TIÊU CHUẨN GIÁM ĐỊNH HÃNG tàu MSC

TIÊU CHUẨN GIÁM ĐỊNH HÃNG tàu MSC TIÊU CHUẨN GIÁM ĐỊNH HÃNG tàu MSC TIÊU CHUẨN GIÁM ĐỊNH HÃNG tàu MSC TIÊU CHUẨN GIÁM ĐỊNH HÃNG tàu MSC TIÊU CHUẨN GIÁM ĐỊNH HÃNG tàu MSC TIÊU CHUẨN GIÁM ĐỊNH HÃNG tàu MSC TIÊU CHUẨN GIÁM ĐỊNH HÃNG tàu MSC

MSC Container Inspection Criteria and Repair Guidelines General The below mentioned criteria should be taken as a guideline and it is applicable for use at all MSC managed/operated and leased general purpose containers Inspection should be done to ensure the container is structurally sound and safe, as defined by the International Convention for Safe Containers (CSC) The container must show a valid CSC plate and “ACEP” approval sticker or stamp All containers “NOT COVERED BY ACEP” must have their CSC plate updated in accordance the CSC regulations Any damages exceed these criteria should be repaired All repairs must be carried conform to General Repair Policy published in the latest edition of the Institute of International Container Lessors (IICL) Any repair completed not confirm to those guidelines can be considered as improper and not acceptable All MSC agents must ensure any appointed MSC depot or terminal performing improper repairs, will be held liable for all consequences Non-ISO improper repairs are absolutely forbidden Full sections and inserts in a crossmember are not allowed Crossmembers bent down, needs to be renewed: repair methods such as cutting in, straighten and reweld are not allowed of Main Structural Components and Cargoworthy Inspection Criteria Rails, Headers, and Sills Component Measurement & Acceptable Criteria Top side rail Deformation not exceeding 30mm; No holes and cracks Deformation not exceeding 50mm; No holes and cracks Cuts and cracks extend up to web radius; No limit on dents Deformation not exceeding 40mm; No holes and cracks Deformation not exceeding 50mm; No holes and cracks Bottom side rail – web only Bottom side rail – flange only Front & Rear Header Front & Rear Sill Corner Post and Corner Casting Component Measurement & Acceptable Criteria Front & Rear corner post Dents not exceeding 20mm; any number of dents No holes and cracks; Deformation not exceeding 5mm beyond corner fitting end face and 10mm beyond corner fitting side face No dents, distortion, and cracks; No worn, gouged or broken apertures; No repairs on the fitting Corner Fitting Floor and Understructure Component Measurement & Acceptable Criteria Floor board - Plywood No holes, broken or finger cracks, and loose board; Surface crack at most outer ply if no signs of impact or overloading; No delamination and hollow sound; No temporary patch using steel plate; No low-quality plywood material No light leakage between boards, center spacers, and rails/sills; Different in height between adjacent board not exceeding 10mm; of Cross members – web only Cross members – upper flange only Forklift pocket, outriggers, and gooseneck tunnel assembly Gouges not exceeding 10mm deep up to 150mm wide; Gouges not exceeding 15mm deep; No protruding fasteners or nails; No transferable stain or adhesive residue Deformation not exceeding 75mm; Bow upwards not exceeding 50mm; Bow downwards not beyond the plane of lower surfaces of the bottom corner fittings; No holes, cracks or cut on web; No welding repair on web Separation of flange and plywood not exceeding 10mm Deformation not exceeding 50mm; Bow upwards not exceeding 50mm; Bow downwards not beyond the plane of lower surfaces of the bottom corner fittings; Cut or crack on lower flange extend up to web radius – connection to bottom side rails only; Horizontal cut or crack not exceeding 500mm extend up to any weld connection Doors Component Measurement & Acceptable Criteria Door panel No holes and cuts; No light leakage Deformation not affecting door operations and water tightness; Deformation not affecting securing of high security bolt seal; Hinge pins and blade are not seized due to corrosion Deformation not affecting door operations and water tightness; Deformation not exceeding 5mm beyond corner fitting end face and 10mm beyond corner fitting side face No holes, cuts, and cracked; No light leakage Door assembly, including hardware J-bars Door gasket of Front, Side, and Roof panels Component Measurement & Acceptable Criteria Side and front panels Deformation which reduces internal width up to 50mm; Deformation not exceeding 40mm beyond corner fitting end face and 40mm beyond corner fitting side face; No holes, cuts, and cracks No transferable stain or adhesive residue for interior panels only No stickers or label in any form and shape; No political, religious, sexual or any offensive graffiti and marking Deformation which reduces internal height up to 70mm; Deformation not exceeding 40mm beyond corner fitting top face; No holes, cuts, and cracks Roof panels Other components Component Measurement & Acceptable Criteria Ventilator cover Watertight; Perforated area is not covered or blocked Valid and readable wording CSC plate Container Number and Weight decals Lashing rings and bars Complete and readable wording No cuts, broken or missing of