... 664) 13 Chỉ số iốt iốt /10 0 g < 12 0 EN 14 111 / TCVN 612 2 (ISO 39 61) 14 Độ ổn định oxy hóa 11 0oC >6 TCVN7895:2008 (EN 14 112 ) 15 Glycerin tự % khối lượng < 0,020 TCVN78 67: 2008 (ASTM D 6584) 16 Glycerin ... pháp 65 D 116 0 D86 24 3.2 .1. 8 So sánh đặc điểm cách tiến hành hai phương 69 pháp D 116 0 D86 Stt Hình /sơ đồ Tên hình /sơ đồ Trang 25 1. 1.3 Biểu đồ thành phần diesel biodiesel pha 26 1. 1.4 Sơđồ sản ... D 67 51 58 ASTM D 975 17 3.2 .1. 1So sánh đặc điểm phạm vi áp dụng D 874 57 D482 18 3.2 .1. 2 So sánh số đặc điểm phạm vi áp dụng D5453 61 D129 19 3.2 .1. 3 So sánh đặc điểm tiến trình thực D5453 60 D129...
... 0,6cm Khuy áo Áo có 15 khuy, khuy thùa nẹp áo (1 khuy cách chân cổ 9cm, khoảng cách khuy lại 10 cm) khuy chân cổ, khuy thùa manchette 10 Nút áo Có 13 nút lớn nút nhỏ (đã có tính nút dự trữ loại ... khảo: BẢNG QUI CÁCH MAY SẢN PHẨM Mã hàng: áo chemise nam dài tay LX – 325 Kế hoạch: 10 .000 áo; Giao hàng: 10 /10 /2005 Stt Tên chi tiết Qui cách may Nắp túi May lộn theo rập mẫu, diễu hai đường ... tâm khuy thùa, tâm khuy nút nẹp áo phải nằm Ứng dụng tiêu chuẩn ASTM D 619 3 nẹp áo để gài nút vào hai nẹp phải trùng khít lên 11 Mật độ mũi mũi/cm Ngày … tháng … năm … Người lập bảng Ký tên Hầu kiến...
... the cavity, and then welding 15 .2 All repaired pipe shall be tested hydrostatically in accordance with Section 11 , unless otherwise specified in 11 .3 16 Inspection 16 .1 The inspector representing ... “NH” 13 Lengths 13 .1 Pipe lengths shall be supplied in accordance with the following regular practice: 13 .1. 1 The lengths shall be as specified on the order with a tolerance of 61 2in (13 mm), ... subjected to the hydrostatic test specified in Section 11 , unless otherwise specified in 11 .3 10 Tensile Properties of Production Welds 10 .1 Reduced-section tension test specimens required in Section...
... characteristics of bituminous materials, 25°C (77 °F) penetration, n—the consistency of a bituminous material expressed as the distance in tenths of a millimetre (0 .1 mm) that a standard needle penetrates ... railroad ballasts, etc coarse aggregate, n— (1) aggregate predominantly retained on the 4 .75 -mm (No 4) sieve: or (2) that portion of an aggregate retained on the 4 .75 -mm (No 4) sieve DISCUSSION—The definitions ... relatively small fine aggregate, n— (1) aggregate passing the 3⁄8-in (9.5-mm) sieve and almost entirely passing the 4 .75 -mm (No 4) sieve and predominantly retained on the 75 -µm (No 200) sieve: or (2)...
... pedestal 3.2 The pedestal shall be 10 to 11 in [250 to 275 mm] square at the top, and 15 to 16 in [ 375 to 400 mm] square at the bottom, 25 to 30 in [625 to 75 0 mm] in height, and shall be of ... RR: C 01 10 06 C 230/C 230M FIG Flow Table and Accessory Apparatus (Partial) (In./Lb) (continued) top opening shall be 2 .75 6 0.02 in [70 .0 0.5 mm] for new molds and 2 .75 + 0.05 in [70 .0 + 1. 3 mm] ... least 14 0 lb/ft3 [2240 kg/m 3] A stable gasket cork padding, 1 2 in [13 mm] thick and the same size as the pedestal bottom or four pieces of padding 1 2 in [13 mm] thick and approximately in [10 0...