1. Trang chủ
  2. » Kỹ Thuật - Công Nghệ

Điện thân xe ô tô Kia

49 2,8K 21
Tài liệu đã được kiểm tra trùng lặp

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 49
Dung lượng 1,45 MB

Nội dung

General Information Actually, ETACS starts by the needs to control time and alarm related electric device of the vehicle in one controller. The controlled items can be more or less according to the vehicle grades or trim levels but the basic concept

Trang 1

E T A C S

Trang 2

General Information

Actually, ETACS starts by the needs to control time and alarm related electric device of the vehicle in one controller

The controlled items can be more or less according to the

vehicle grades or trim levels but the basic concept is similar That is why a system of a vehicle is familiarized, easy

to understand other systems.

Trang 3

General Information

Seat Belt Warning

Tail Lamp Auto Cut

Central Door Lock

IGN Key operated warning IGN Key Reminder

Crash Door Unlock

Anti - theft Function

Keyless Entry Function

ETACS Module Function

Trang 4

All Door Switch (each door S/W)

Hood Switch / Trunk Switch

Door Lock/Unlock Switch (in actuator)

Ignition Key Warning Switch

Tail Lamp Switch

Trang 5

E T A C S

FUNCTION

Detail

Trang 6

Seat Belt Warning Timer

Description

1 Seat belt warning lamp must blink for 6 seconds from IG ON with 0.9 sec.

frequency, 50% duty, and chime bell should ring too.

2 If the IG is turned OFF within 6 seconds, the warning lamp and chime bell

output should be OFF.

3 In case of the seat belt switch is ON, the chime bell sound must be stopped

immediately, but seat belt warning lamp output should be ON during 6 seconds.

4 If the seat belt is not fastened while IG is ON, the warning lamp

and chime bell output should be repeated continuously until the seat belt is fastened.

* T1 : 6 ±1.0 sec * T2 : 0.45 ±0.1 sec *T3:0.3 ±0.1sec

OnOff

Trang 7

Seat Belt Warning Timer

STIG1IG2

Trang 8

Key Operated Warning

Description

1 If the driver door is opened with the IG key is inserted into key cylinder,

the chime bell should ring with 0.9 second frequency, 50% duty continuously.

2 When the key is removed from key cylinder or the driver door is closed,

door warning output is stopped immediately.

▶ Chime Bell Operating Order : Seat belt warning → Key operated warning

OnOff

* T1 & T2 : 0.45 ± 0.1 sec

Trang 9

Key Operated Warning

Chime Bell

Key Operated Door Warning S/W

from BATT.Driver’s DR S/W

to DR opening indicator

in cluster

E T A C S C M

Trang 10

Ignition Key Reminder Control

Description

This function is to prevent vehicle from Lock if IG key is inserted into key cylinder.

1 IG key is inserted into key cylinder.

2 The signal of IG key insert condition is perception in ETACSCM.

3 At this time if pushed door lock knob of front LH or RH door, door unlock signal

output for 1 sec.

4 So, that during insert key into the key-cylinder to prevent door lock

DR Warning

Switch

OnOffFRT LH/RH

CASE 1

T2

Trang 11

Ignition Key Reminder Control

Trang 12

Ignition Key Reminder Control

AM Acc IG1 IG2 ST

Each Door Lock Actuator

143Ω 143Ω

Battery

Battery Battery

Central Door Lock Relay

by Key or Knob

Door Lock Knob

Door Warning

Switch

Trang 13

Tail Lamp Auto Cut(off)

Description

1 In case of the tail lamp switch is turned ON after IG SW ON or the driver door

is opened after IG SW OFF, the tail lamp is extinguished automatically.

2 In addition, the IG SW is turned OFF after driver door is opened with

IG SW is ON condition, the tail lamp will be extinguished automatically too.

3 After automatic extinguish, if the tail lamp switch is turned ON again,

then, the tail lamp will be ON (illuminating) and the auto cut function will be released.

IG KEY

Switch

OnOffOnOffOpenClose

Trang 14

Tail Lamp Auto Cut(off)

ACC IG2 IG1 ST

B1 B2 ACC IG2 IG1 ST

IGN SW

L R Alternator

A17

B13

Tail Lamp Fusible Link

BATT

Trang 15

Central Door Lock Control

Description

The ETACS module receives “Lock/Unlock” signal from the front LH or RLH door switch, door “Lock” or

“Unlock” relay is executed 0.5second later

◆ In case of front LH or RH door switch is on less than 60ms, door actuator should be off

Trang 16

Central Door Lock Control

AM Acc IG1 IG2 ST

Each Door Lock Actuator

143Ω 143Ω

Battery

Battery Battery

by Key or Knob

Trang 17

Crash Door Unlock

Description

1 If the airbag signal is inputted to the ETACS when the door is locked, the unlock signal is executed immediately for safety

2 At this time, all door should be unlocked for operating above “unlock execution”

3 “Door unlock” is activated only one time while IGN 1 switch is on

T1

T1 : 200 ms T2 : 40 m sec T3 : 5 sec ± 0.5 sec

Air Bag Module

Trang 18

Crash Door Unlock

A/BAG Module

A/BAGCM CRASH SIGNAL

A : Door Lock Actuator

AM Acc IG1 IG2 ST

Central Door LockRelay in J/BOX

Dash Fuse

143Ω Unlock RLY Lock RLY.

Battery

Trang 19

ANTI-THEFT FUNCTION

Trang 20

General Information

Trang 21

Anti-theft system Block Diagram

Transmitter(TX)

Lock button

Unlock button Receiver(RX) ETACSCM

Door Actuator Hazard Lamp Relay Start Inhibit Relay Alarm Horn

Rolling Code

Door Lock or Door Unlock

Actuator Actuating

Trang 22

General Information

Anti - theft system General

Anti-theft system Transmitter Rolling Code

Rolling Code Example.

3F50C19 3F50C20 3F50C21

ETACSCM

Lo Signal by Time Lock : 50 ms.

Unlock : 100 ms.

Trang 23

Input and Output

E T A C S C M

- Transmitter signal

Door lock button signal

Door unlock button signal

- All door lock/unlock

signal

- All door switch

- Hood switch

- Door lock/unlock actuator

- Arm status

- Disarm status

- Alarm horn

- Hazard relay

- Start inhibiter relay

Input Signal Controller Output Signal

Trang 24

Arm Function

Description

1 If the ETACS receives the “Lock” signal from TX.( when IG key removed from key cylinder and all switchs are closed)

ETACS outputs “ON” the “Lock” outputs and vehicle becomes “Armed condition” with turn on the Hazard

lamp for 1 sec After confirming lock signal of door lock actuator.

2.If the ETACS receives the “Lock “ signal from TX when any one switch of all door switches is open, it outputs “ON” the “Lock” output only,

In this case, ETACS does not output Hazard lamp “ON” and the vehicle does not “Armed”

3 The door is closed in the above “2” condition, ETACS output “ON” the Hazard lamp for 1sec And the vehicle is Armed.

4 If lock button on the TX is pushed again under “Armed” condition, only Hazard lamp is “ON” for 1sec With maintaining Armed condition.

☞ Only the TX can make the “Armed” condition for the vehicle.

OpenClose

Door Lock

Actuator

OnOff

Hazard

Lamp OnOff

Max 0.5 sec.

Trang 25

Disarm Function

Description

1 When TX unlock button pushed, door unlock output and the vehicle is “Disarmed”.

At this time, Hazard lamp output “ON” twice.

2 If unlock(TX) button is pushed again under “Unlocked” condition, only Hazard lamp output “ON” twice In this case, door unlock is not output again

☞ To disarm impassible using by door key switch.

Alarm Relay OnOff

T1 T1 T1

T1 : 0.5 ± 0.1 sec

Trang 26

Alarm Function 1 (General area, non EC)

Trang 27

Alarm Function 2 (EC only)

3 If the door is opened again after first alarm the alarm is operated again 27±2 sec

Arm State Arm

On

T2Hazard Lamp

T2

Trang 28

Hazard

Lamp OffOn

T2

T1 T1

Trang 29

Alarm Function 4

Description

1.In the alarm mode, if the hood(or door) is opened and battery is disconnected,

all functions stopped.

2.In the condition above, when battery is removed, start inhibit, siren and Hazard lamp are activated.

☞**one time for EC, three times for the other area

Start

DisarmArm State

OffOn

Trang 30

Description

If TX lock is received after the opened(invaded) door is closed while alarm, then ETACS outputs the “Door lock” and confirms the lock signal from the door actuator

And turns the siren and start inhibitor “OFF”

At this case, Hazard lamp becomes Armed” condition after output “ON” once

※ Start inhibitor on : can not start, Start inhibitor off : cant start

Trang 31

OffOn

Trang 32

1 Alarm cancellation can be performed by TX.

2 To release alarm situation by an ignition key, turn it “ON” and wait for 30 seconds until the alarm sound comes off and arm release.

HORN

OFFON

Trang 33

Alarm & Hazard circuit

5V

ST

IG1IG2

Turn signal Lamp

A/T : InhibitorM/T : IGN Lock SW

From start relay

Trang 34

Start Inhibitor circuit 1

Q1.What we have to check is start motor doesn’t work in Anti-theft system?(no power supply to the “ST” terminal of start motor Q2.What is the voltage of the pin from Ignition lock switch start out relay?(Pin No 8) 2-1.at Alarm mode : ( ) volt 2-2.at Disarm mode : ( ) volt 2-3.at Arm mode : ( ) volt Q3.What are the conditions for Burglar Alarm Relay to be on?

Trang 35

Start Inhibitor circuit 2

L2 3

D R N P

B1 B2 ACC IG2 IG1 ST

L R

Trang 36

Anti - theft system optional

1 Anti - theft system optional : with Immobilizer

1-1 Application area : EC

1-2 Circuit

AM Acc IG1 IG2 ST Acc

ON ST

Ignition Switch

L R

ALTERNATOR

100A

E T A C S C M

Trang 37

Communication wave form

Communication wave form between receiver & ETACSCM

Communication Line

TX

Trang 38

Anti - theft system optional

2 Anti - theft system optional : without Immobilizer

2-1 Application area : General

Ignition Switch

L R

ALTERNATOR

100A

E T A C S C M

Trang 39

Operating temperature range -20 ~+60℃

Modulation ASK (Amplitude Shift Keying)

315.00MHz(General)

Battery Life 2 Year(10 times/a day) - Lithium 3V 1EA

Trang 40

◆ When the IG Key is removed from key cylinder.

◆ When the SET/OFF switch on keyless entry system receiver is put on the “OFF” (Operation mode)

T2

T1

T1

T1ON

OFF

Lock Button Pushed

Unlock Button Pushed

DR UN LOCK

OUTPUT

Trang 41

Each Door Lock Actuator

143Ω 143Ω

Battery

Battery Battery

Central Door Lock Relay

by Key or Knob Monitor Line

Central Door Lock Control Circuit by Remote Control Circuit.

Trang 42

Code Saving method

1 without Immobilizer vehicle

※Off/Set switch located

on receiver.

OFF SET

1

OFF SET 2

2.Move the “OFF/SET” switch to “SET”

position and all door close and push “Lock & Unlock” button of the Transmitter at the

same time and Lock or Unlock push once

SET

Trang 43

Code Saving method

2 with Immobilizer vehicle

OFF SET

※Off/Set switch located

on ICM.

2.Move the “OFF/SET” switch to “SET”

position and and push “Lock & Unlock”

button of the Transmitter at the same time

and Lock or Unlock push once again.

◐ OFF/SET switch is on “OFF” position

at first.

OFF SET 2

Trang 44

Code Saving Case

1 2EA Transmitter Code Saving Case 1, from the beginning

OFF/SET SW

Position

OFFSET

OFFON(Push)

OFFON(PUSH)

Transmitter”1”

Look & Unlock

Pushed

1sec

1) 1st TX Pushed Look & Unlock Button at the same time

1) 2nd TX Pushed Lock & Unlock Button at the same time

2) Pushed Lock or Unlock Button at once again

2) Pushed Lock or Unlock Button at once again

2 1

2 1

Trang 45

Code Saving Case

2 Transmitter Code Saving Case 2

After one more purchasing in one key use : Have to be code save both of

TX

OFF/SET SW

Position

OFFSET

OFFON(Push)

OFFON(PUSH)

Transmitter”1”

Lock & Unlock

Pushed

1sec

1) 1st TX Pushed Lock & Unlock Button at the same time(used TX)

1) 2nd TX Pushed Lock & Unlock Button at the same time(brand new TX)

2) Pushed Lock or Unlock Button at once again

2) Pushed Lock or Unlock Button at once again

2 1

2 1

Trang 46

Code Saving Case

3 Transmitter Code Saving Case 3

Newly usage after losing one key in two keys use : Have to be code save both of TX

OFF/SET SW

Position

OFFSET

OFFON(Push)

OFFON(PUSH)

1sec

1) 1st TX Pushed Lock & Unlock Button at the same time(used TX)

1) 2nd TX Pushed Lock & Unlock Button

at the same time(brand new TX)

2) Pushed Lock or Unlock Button at once again

2) Pushed Lock or Unlock Button at once again

1 2

2 1

Trang 47

Code Saving Case

4 Transmitter Code Saving Case 4

The first key and the second that is registered remote code must not use and third one is

possible to use only, if two pieces of remote keys are registered and registered one

more

1) 3rd TX Pushed Lock Button

at the same time(New TX) : Can be use.)

1) 2nd TX Pushed Lock & Unlock Button

at the same time(used TX) : Memory Erased

2) Pushed Lock or Unlock Button at once again

OFF/SET SW

Position

OFFSET

1) 1st TX Pushed Lock & Unlock Button

at the same time(used TX) - Memory Erased)

1sec

1sec

10 sec

2) Pushed Lock or Unlock Button at once again

2) Pushed Lock or Unlock Button at once again

1 2

1 2

2 1

Trang 48

Key code saving to use Hi-scan

1) Connect the DLC cable to the 16-pin connector of the keyless adapter

2) Connect the 10-pin connector of the keyless adapter into the muti purpose ch eck connector next to the Data Link Connector Turn the Hi-scan ON and press ENTER.

3) Select the vehicle model

4) Select code saving menu

5) Follow steps 1 to 3 according to the message shown in the Hi-scan screen

to complete the transmitter code saving

Trang 49

I.C.M RELAY

- Characteristic

☞ I.C.M (Integrated Circuit Module) Relay

I.C.M Relay Outside view

I.C.M Relay Inside view

Ngày đăng: 22/10/2012, 09:12

TỪ KHÓA LIÊN QUAN

w