Tài liệu hướng dẫn sửa chữa xe Nissan teana j32 esm tai lieu sua chua phan 5. Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác, hiệu quả, hợp lý
DRIVER INFORMATION & MULTIMEDIA SECTION WCS WARNING CHIME SYSTEM A B C D E CONTENTS BASIC INSPECTION DIAGNOSIS AND REPAIR WORKFLOW Work Flow KEY WARNING CHIME : Component Parts Location 12 KEY WARNING CHIME : Component Description 12 DIAGNOSIS SYSTEM (METER) 13 F G FUNCTION DIAGNOSIS CONSULT-III Function (METER/M&A) 13 WARNING CHIME SYSTEM DIAGNOSIS SYSTEM (BCM) 17 H WARNING CHIME SYSTEM WARNING CHIME SYSTEM : System Diagram WARNING CHIME SYSTEM : System Description WARNING CHIME SYSTEM : Component Parts Location WARNING CHIME SYSTEM : Component Description COMMON ITEM 17 COMMON ITEM : CONSULT-III Function (BCM COMMON ITEM) .17 I LIGHT REMINDER WARNING CHIME LIGHT REMINDER WARNING CHIME : System Diagram LIGHT REMINDER WARNING CHIME : System Description LIGHT REMINDER WARNING CHIME : Component Parts Location LIGHT REMINDER WARNING CHIME : Component Description BUZZER .18 BUZZER : CONSULT-III Function (BCM - BUZZER) 18 COMPONENT DIAGNOSIS 20 K POWER SUPPLY AND GROUND CIRCUIT 20 COMBINATION METER 20 COMBINATION METER : Diagnosis Procedure 20 L BCM (BODY CONTROL MODULE) 20 BCM (BODY CONTROL MODULE) : Diagnosis Procedure 20 M METER BUZZER CIRCUIT 22 PARKING BRAKE RELEASE WARNING CHIME PARKING BRAKE RELEASE WARNING CHIME : System Diagram PARKING BRAKE RELEASE WARNING CHIME : System Description PARKING BRAKE RELEASE WARNING CHIME : Component Parts Location 10 PARKING BRAKE RELEASE WARNING CHIME : Component Description 10 WARNING CHIME SYSTEM 23 KEY WARNING CHIME 10 KEY WARNING CHIME : System Diagram 11 KEY WARNING CHIME : System Description 11 Reference Value 27 Wiring Diagram - METER - 33 Fail-Safe 41 DTC Index .42 Revision: 2008 December J Description .22 Component Function Check 22 Diagnosis Procedure 22 WCS O Wiring Diagram - WARNING CHIME - 23 ECU DIAGNOSIS 27 COMBINATION METER 27 WCS-1 J32 P BCM (BODY CONTROL MODULE) 44 Reference Value 44 Wiring Diagram - BCM - 68 Fail-safe 81 DTC Inspection Priority Chart 83 DTC Index 84 SYMPTOM DIAGNOSIS 86 THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR DOES NOT SOUND 86 Description 86 Diagnosis Procedure 86 Revision: 2008 December THE LIGHT REMINDER WARNING DOES NOT SOUND 87 Description 87 Diagnosis Procedure 87 THE KEY WARNING DOES NOT SOUND 88 Description 88 Diagnosis Procedure 88 PRECAUTION 89 PRECAUTIONS 89 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 89 WCS-2 J32 DIAGNOSIS AND REPAIR WORKFLOW < BASIC INSPECTION > BASIC INSPECTION A DIAGNOSIS AND REPAIR WORKFLOW Work Flow INFOID:0000000003803203 B OVERALL SEQUENCE C D E F G H I J K L M JSNIA0733GB DETAILED FLOW 1.OBTAIN INFORMATION ABOUT SYMPTOM WCS Interview the customer to obtain as much information as possible about the conditions and environment under which the malfunction occurred O >> GO TO 2.CHECK SYMPTOM P • Check the symptom based on the information obtained from the customer • Check if any other malfunctions are present >> GO TO 3.CHECK CONSULT-III SELF-DIAGNOSIS RESULTS Connect CONSULT-III and perform self-diagnosis Refer to WCS-13, "CONSULT-III Function (METER/M&A)" Revision: 2008 December WCS-3 J32 DIAGNOSIS AND REPAIR WORKFLOW < BASIC INSPECTION > Are self-diagnosis results normal? YES >> GO TO NO >> GO TO 4.NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS Perform symptom diagnosis and narrow down the malfunctioning parts >> GO TO 5.REPAIR OR REPLACE MALFUNCTIONING PARTS Repair or replace malfunctioning parts NOTE: If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts >> GO TO 6.FINAL CHECK Check that the warning buzzer in the combination meter operates normally Does it operate normally? YES >> INSPECTION END NO >> GO TO Revision: 2008 December WCS-4 J32 WARNING CHIME SYSTEM < FUNCTION DIAGNOSIS > FUNCTION DIAGNOSIS A WARNING CHIME SYSTEM WARNING CHIME SYSTEM B WARNING CHIME SYSTEM : System Diagram INFOID:0000000003803204 C D E F G H I JSNIA1797GB WARNING CHIME SYSTEM : System Description J INFOID:0000000003803205 K COMBINATION METER • The buzzer (1) for the warning chime system is integrated in the combination meter • The combination meter sounds the alarm buzzer installed in the combination meter when receiving the buzzer output signal transmitted from each unit L M WCS JPNIA1010ZZ O BCM BCM receives signals from various units and transmits a buzzer output signal to the combination meter via CAN communication if it judges that the warning buzzer should be activated P BCM warning function list Revision: 2008 December WCS-5 J32 WARNING CHIME SYSTEM < FUNCTION DIAGNOSIS > Warning functions Signal name Light reminder warning chime • Ignition switch signal • Lighting switch position signal • Door switch signal (driver side) Key warning chime • Ignition signal • Key switch signal • Door switch signal (driver side) NOTE: Parking brake release warning chime is detected by combination meter WARNING CHIME SYSTEM : Component Parts Location INFOID:0000000003803206 JPNIA1332ZZ ABS actuator and electric unit (control unit) Front door switch (driver side) Combination switch (Lighting switch) Parking brake switch Key slot BCM Combination meter A Behind the combination meter Revision: 2008 December WCS-6 J32 WARNING CHIME SYSTEM < FUNCTION DIAGNOSIS > WARNING CHIME SYSTEM : Component Description INFOID:0000000003803207 A Unit Combination meter Description • Receives a buzzer output signal from the BCM with CAN communication line and sounds the buzzer • Judges whether the parking brake is released from the vehicle speed signal received from the ABS actuator and electric unit (control unit) with CAN communication line and the parking brake switch signal from the parking brake switch, and sounds the buzzer if necessary BCM Transmits signals provided by various units to the combination meter with CAN communication line ABS actuator and electric unit (control unit) Transmits the vehicle speed signal to combination meter with CAN communication line Combination switch (Lighting switch) Transmits the lighting switch position signal to BCM Front door switch (driver side) Transmits the door switch signal to BCM Parking brake switch Refer to MWI-52, "Description" B C D E F LIGHT REMINDER WARNING CHIME LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000003803208 G H I J JPNIA0749GB LIGHT REMINDER WARNING CHIME : System Description INFOID:0000000003803209 K DESCRIPTION With ignition switch in the OFF or ACC position, when the driver door is open and the lighting switch is the 1st or 2nd position, the light warning chime will sound • BCM detects ignition switch in the OFF or ACC position, front door switch (driver side) ON, and lighting switch in 1st or 2nd position Then the BCM transmits the buzzer output signal (light reminder warning chime) to combination meter with CAN communication line • When combination meter receives buzzer output signal (light reminder warning chime), it sounds the buzzer L M WARNING OPERATION CONDITIONS WCS If all of the following conditions are fulfilled • Ignition switch is in the OFF or ACC • Lighting switch is in the 1st or 2nd position • Front door switch (driver side) is ON O WARNING CANCEL CONDITIONS Warning is canceled if any of the following conditions is fulfilled • Lighting switch OFF • Ignition switch ON • Front door switch (driver side) is OFF Revision: 2008 December WCS-7 P J32 WARNING CHIME SYSTEM < FUNCTION DIAGNOSIS > LIGHT REMINDER WARNING CHIME : Component Parts Location INFOID:0000000003826866 JPNIA1332ZZ ABS actuator and electric unit (control unit) Front door switch (driver side) Combination switch (Lighting switch) Parking brake switch Key slot BCM Combination meter A Behind the combination meter LIGHT REMINDER WARNING CHIME : Component Description Unit INFOID:0000000003803211 Description Combination meter Receives a buzzer output signal from the BCM and sounds the buzzer BCM Judges the light warning conditions from the signals provided by various switches and transmits a buzzer output signal to the combination meter via CAN communication line if necessary Combination switch (Lighting switch) Transmits the lighting switch position signal to BCM Front door switch (driver side) Transmits the door switch signal to BCM PARKING BRAKE RELEASE WARNING CHIME Revision: 2008 December WCS-8 J32 WARNING CHIME SYSTEM < FUNCTION DIAGNOSIS > PARKING BRAKE RELEASE WARNING CHIME : System Diagram INFOID:0000000003803216 A B C JPNIA0751GB D PARKING BRAKE RELEASE WARNING CHIME : System Description INFOID:0000000003803217 E DESCRIPTION Parking brake release warning chime judges the remaining parking brake according to the vehicle speed signal received from the ABS actuator and electric unit (control unit) via CAN communication and the parking brake switch signal from parking brake switch to sound the warning buzzer F WARNING OPERATION CONDITIONS G If all of the following conditions are fulfilled • Vehicle speed is km/h (4.3 MPH) or higher • Parking brake switch ON H WARNING CANCEL CONDITIONS Warning is canceled if any of the following conditions are fulfilled • Vehicle speed is approximately km/h (1.9 MPH) or less • Parking brake switch OFF I J K L M WCS O P Revision: 2008 December WCS-9 J32 WARNING CHIME SYSTEM < FUNCTION DIAGNOSIS > PARKING BRAKE RELEASE WARNING CHIME : Component Parts Location INFOID:0000000003826867 JPNIA1332ZZ ABS actuator and electric unit (control unit) Front door switch (driver side) Combination switch (Lighting switch) Parking brake switch Key slot BCM Combination meter A Behind the combination meter PARKING BRAKE RELEASE WARNING CHIME : Component Description Unit INFOID:0000000003803219 Description Combination meter Judges the remaining parking brake according to the vehicle speed signal received from the ABS actuator and electric unit (control unit) via CAN communication and the parking brake switch signal from parking brake switch and sounds the warning buzzer ABS actuator and electric unit (control unit) Transmits the vehicle speed signal to the combination meter via CAN communication Parking brake switch Transmits the parking brake switch signal to the combination meter KEY WARNING CHIME Revision: 2008 December WCS-10 J32 PRECAUTIONS < PRECAUTION > PRECAUTION A PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" B INFOID:0000000004362511 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module, see the “SRS AIR BAG” • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors C D E F G PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the H ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury • When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the VTL battery, and wait at least minutes before performing any service Precaution Necessary for Steering Wheel Rotation after Battery Disconnect INFOID:0000000004362512 NOTE: • Before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables • Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work If a DTC is detected, perform trouble diagnosis according to self-diagnosis results This vehicle is equipped with a push-button ignition switch and a steering lock unit If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure below before starting the repair operation OPERATION PROCEDURE K L M N Connect both battery cables NOTE: Supply power using jumper cables if battery is discharged Turn the push-button ignition switch to ACC position (At this time, the steering lock will be released.) Disconnect both battery cables The steering lock will remain released with both battery cables disconnected and the steering wheel can be turned Perform the necessary repair operation When the repair work is completed, re-connect both battery cables With the brake pedal released, turn the push-button ignition switch from ACC position to ON position, then to LOCK position (The steering wheel will lock when the push-button ignition switch is turned to LOCK position.) Perform self-diagnosis check of all control units using CONSULT-III Revision: 2008 December J VTL-9 J32 O P PRECAUTIONS < PRECAUTION > Precaution for Procedure without Cowl Top Cover INFOID:0000000004362513 When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc PIIB3706J Revision: 2008 December VTL-10 J32 PREPARATION < PREPARATION > PREPARATION A PREPARATION Commercial Service Tool INFOID:0000000003839435 Tool name Description Remover tools B C D Remove clips, pawls, metal clips E PIIB7923J F G H VTL J K L M N O P Revision: 2008 December VTL-11 J32 AIR CONDITIONER FILTER < ON-VEHICLE MAINTENANCE > ON-VEHICLE MAINTENANCE AIR CONDITIONER FILTER Exploded View INFOID:0000000003839437 JPIIA0895ZZ Heater & cooling unit assembly Air conditioner filter Removal and Installation Filter cover INFOID:0000000003839438 REMOVAL Remove filter cover (1), and then remove air conditioner filter (2) JPIIA0896ZZ INSTALLATION Installation is basically the reverse order of removal CAUTION: • If the filter is deformed/damaged when removing, replace it with a new one Deformed/damaged filter may deteriorate the dust collecting performance • When installing, handle the filter with extreme care to avoid deforming/damaging • Never open the wrap until just before the installation Because the high performance filter (for odors, pollen, and other allergens) immediately starts absorbing odors by opening the wrap to remove them (with ACCS) Replacement INFOID:0000000003839439 Replace air conditioner filter Refer to MA-5, "Periodic Maintenance" Affix a caution label inside the glove box when replacing filter Revision: 2008 December VTL-12 J32 DUCT AND GRILLE < ON-VEHICLE REPAIR > ON-VEHICLE REPAIR A DUCT AND GRILLE Exploded View INFOID:0000000003839472 B FRONT C D E F G H VTL J K JPIIA1301ZZ Side defroster nozzle (right) Defroster nozzle Side defroster nozzle (left) Heater & cooling unit assembly Foot duct (left) Ventilator duct Side defroster grille (left) Instrument panel assembly Side ventilator grille (left) 10 Center ventilator grille (left) 11 Cluster lid D L M 12 Center ventilator grille (right) 13 Side ventilator grille (right) 14 Side defroster grille (right) 15 Bracket 16 Ionizer 17 Harness 18 Foot duct (right) N 19 Blower unit A With plasmacluster REAR O P Revision: 2008 December VTL-13 J32 DUCT AND GRILLE < ON-VEHICLE REPAIR > JPIIA1129ZZ Heater & cooling unit assembly Rear foot duct (left) Rear foot duct (left) Rear foot duct (left) Rear ventilator duct Console rear cover (Rear ventilator grille) Rear foot duct (right) Rear foot duct (right) Rear foot duct (right) 10 Rear ventilator duct A With rear ventilation CENTER VENTILATOR GRILLE CENTER VENTILATOR GRILLE : Removal and Installation INFOID:0000000003839473 REMOVAL Remove cluster lid D Refer to IP-11, "Exploded View" Disengage the pawls, and then remove center ventilator grilles (left and right) (1) : pawl JPIIA0929ZZ INSTALLATION Installation is basically the reverse order of removal SIDE VENTILATOR GRILLE Revision: 2008 December VTL-14 J32 DUCT AND GRILLE < ON-VEHICLE REPAIR > SIDE VENTILATOR GRILLE : Removal and Installation INFOID:0000000003839475 A REMOVAL Remove ventilator duct Refer to VTL-13, "Exploded View" Disengage the pawls, and then remove side ventilator grilles (left and right) (1) B C : pawl D E JPIIA0930ZZ INSTALLATION Installation is basically the reverse order of removal F SIDE DEFROSTER GRILLE SIDE DEFROSTER GRILLE : Removal and Installation INFOID:0000000003839477 G REMOVAL Remove side defroster nozzles (left and right) Refer to VTL-13, "Exploded View" Remove mounting screws (A), and then remove side defroster grilles (left and right) (1) H VTL J K JPIIA0931ZZ INSTALLATION L Installation is basically the reverse order of removal VENTILATOR DUCT VENTILATOR DUCT : Removal and Installation INFOID:0000000003839479 M REMOVAL N Remove instrument panel assembly Refer to IP-11, "Exploded View" O P Revision: 2008 December VTL-15 J32 DUCT AND GRILLE < ON-VEHICLE REPAIR > Remove mounting screws (A) JPIIA0932ZZ Remove ionizer harness connector (B) (if equipped) Remove ventilator duct (1) Remove ionizer (if equipped) Refer to HAC-133, "Exploded View" INSTALLATION Installation is basically the reverse order of removal SIDE DEFROSTER NOZZLE SIDE DEFROSTER NOZZLE : Removal and Installation INFOID:0000000003839481 REMOVAL Remove ventilator duct Refer to VTL-13, "Exploded View" Remove mounting screw (A), and then remove side defroster nozzle (left) (1) JPIIA0933ZZ Remove mounting screw (B) and harness clip (C), and then remove side defroster nozzle (right) (2) INSTALLATION Installation is basically the reverse order of removal DEFROSTER NOZZLE DEFROSTER NOZZLE : Removal and Installation INFOID:0000000003839483 REMOVAL Revision: 2008 December VTL-16 J32 DUCT AND GRILLE < ON-VEHICLE REPAIR > Remove side defroster nozzles (left and right) Refer to VTL-13, "Exploded View" Remove mounting screws (A), and then remove defroster nozzle (1) A B C D E F JPIIA0934ZZ INSTALLATION G Installation is basically the reverse order of removal REAR VENTILATOR GRILLE REAR VENTILATOR GRILLE : Removal and Installation INFOID:0000000003839485 H REMOVAL VTL Remove console rear cover (rear ventilator grille) Refer to IP-22, "Exploded View" INSTALLATION Installation is basically the reverse order of removal J REAR VENTILATOR DUCT REAR VENTILATOR DUCT : Removal and Installation INFOID:0000000003839487 K REMOVAL Remove rear ventilator duct Refer to VTL-13, "Exploded View" Remove instrument stay Refer to VTL-21, "Exploded View" (RHD models) Remove mounting clip (A), and then remove rear ventilator duct (1) L M N O JPIIA0936ZZ INSTALLATION P Installation is basically the reverse order of removal REAR VENTILATOR DUCT REAR VENTILATOR DUCT : Removal and Installation INFOID:0000000003839489 REMOVAL Revision: 2008 December VTL-17 J32 DUCT AND GRILLE < ON-VEHICLE REPAIR > Remove center console assembly Refer to IP-22, "Exploded View" Remove screws (A), and then remove rear ventilator duct (1) JPIIA0937ZZ INSTALLATION Installation is basically the reverse order of removal REAR FOOT DUCT REAR FOOT DUCT : Removal and Installation INFOID:0000000003839491 REMOVAL Remove instrument lower cover LH Refer to IP-11, "Exploded View" Remove rear foot duct (left) (1) JPIIA0938ZZ INSTALLATION Installation is basically the reverse order of removal REAR FOOT DUCT REAR FOOT DUCT : Removal and Installation INFOID:0000000003839493 REMOVAL Remove rear foot duct (left) Refer to VTL-13, "Exploded View" Remove front seat assembly (left) Refer to SE-103, "Exploded View" (WITH VENTILATION SEAT) or SE152, "Exploded View" (WITHOUT VENTILATION SEAT) Pull up floor trim of left side Refer to INT-47, "Exploded View" Remove mounting clip (A), and then remove rear foot duct (left) (1) JPIIA0940ZZ INSTALLATION Revision: 2008 December VTL-18 J32 DUCT AND GRILLE < ON-VEHICLE REPAIR > Installation is basically the reverse order of removal REAR FOOT DUCT A REAR FOOT DUCT : Removal and Installation INFOID:0000000003839495 B REMOVAL Remove front seat assembly (left) Refer to SE-103, "Exploded View" (WITH VENTILATION SEAT) or SE152, "Exploded View" (WITHOUT VENTILATION SEAT) Pull up floor trim of left side Refer to INT-47, "Exploded View" Remove mounting clip (A) and harness clip (B), and then remove rear foot duct (left) (1) C D E F JPIIA0942ZZ G INSTALLATION Installation is basically the reverse order of removal FOOT DUCT H FOOT DUCT : Removal and Installation (LHD models) INFOID:0000000003839497 VTL REMOVAL Driver side Remove instrument driver lower panel Refer to IP-11, "Exploded View" Remove mounting screws (A), and then remove foot duct (left) (1) J K L M JPIIA0944ZZ Passenger side N Remove blower unit assembly Refer to VTL-21, "Exploded View" Remove mounting screws (A) and harness clip, and then remove foot duct (right) (1) O P JPIIA0945ZZ INSTALLATION Revision: 2008 December VTL-19 J32 DUCT AND GRILLE < ON-VEHICLE REPAIR > Installation is basically the reverse order of removal FOOT DUCT : Removal and Installation (RHD models) INFOID:0000000004268023 REMOVAL Driver side Remove device assembly, and then move it to a position where it dose not inhibit work Refer to PB-14, "Exploded View" Remove mounting screws (A), and then remove foot duct (right) (1) JPIIA1138ZZ Passenger side Remove blower unit assembly Refer to VTL-21, "Exploded View" Remove mounting screws (A) and harness clip, and then remove foot duct (left) (1) JPIIA1139ZZ INSTALLATION Installation is basically the reverse order of removal Revision: 2008 December VTL-20 J32 BLOWER UNIT < ON-VEHICLE REPAIR > BLOWER UNIT A Exploded View INFOID:0000000003839458 B C D E F G H VTL JPIIA0914GB Blower unit Heater & cooling unit assembly Instrument stay Instrument panel assembly Steering member J Refer to GI-4, "Components" for symbols in the figure K DISASSEMBLY L M N O P Revision: 2008 December VTL-21 J32 BLOWER UNIT < ON-VEHICLE REPAIR > JPIIA1302ZZ Shutter box case Intake door Intake upper case Intake door motor Intake lower case Blower motor Outlet seal Intake seal BLOWER UNIT BLOWER UNIT : Removal and Installation INFOID:0000000003940541 REMOVAL Remove instrument panel assembly Refer to IP-11, "Exploded View" Remove mounting nuts (A), and then remove instrument stay (1) JPIIA0909ZZ Disconnect intake door motor and blower motor connectors Revision: 2008 December VTL-22 J32 BLOWER UNIT < ON-VEHICLE REPAIR > Remove heater & cooling unit assembly mounting bolts (A) and blower unit mounting bolts (B) A B C D E F G H JPIIA0910ZZ Remove steering member mounting bolts (C) (right) Remove blower unit (2) while pulling steering member (1) VTL INSTALLATION Installation is basically the reverse order of removal BLOWER MOTOR J BLOWER MOTOR : Removal and Installation INFOID:0000000003839461 K REMOVAL Remove globe box assembly Refer to IP-11, "Exploded View" Disconnect blower motor connector Remove mounting screws (A), and then remove blower motor (1) L M N O JPIIA0911ZZ INSTALLATION P Installation is basically the reverse order of removal Revision: 2008 December VTL-23 J32