Nissan teana j32 esm tai lieu sua chua phan 1

Tài liệu hướng dẫn sửa chữa xe Nissan teana j32 esm tai lieu sua chua phan 1. Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chửa nhanh chóng, chính xác, hiệu quả, hợp lý

BODY INTERIOR SECTION ADP AUTOMATIC DRIVE POSITIONER A B C D E CONTENTS BASIC INSPECTION DIAGNOSIS AND REPAIR WORK FLOW Work Flow INSPECTION AND ADJUSTMENT ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Description ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement SYSTEM INITIALIZATION SYSTEM INITIALIZATION : Description SYSTEM INITIALIZATION : Special Repair Requirement MEMORY STORING MEMORY STORING : Description MEMORY STORING : Special Repair Requirement AUTOMATIC DRIVE POSITIONER SYSTEM : System Diagram 11 AUTOMATIC DRIVE POSITIONER SYSTEM : System Description 11 AUTOMATIC DRIVE POSITIONER SYSTEM : Component Parts Location 13 AUTOMATIC DRIVE POSITIONER SYSTEM : Component Description 14 MANUAL FUNCTION 15 MANUAL FUNCTION : System Diagram 15 MANUAL FUNCTION : System Description 15 MANUAL FUNCTION : Component Parts Location 17 MANUAL FUNCTION : Component Description 18 MEMORY FUNCTION 18 MEMORY FUNCTION : System Diagram .19 MEMORY FUNCTION : System Description 19 MEMORY FUNCTION : Component Parts Location 21 MEMORY FUNCTION : Component Description 22 EXIT ASSIST FUNCTION 22 EXIT ASSIST FUNCTION : System Diagram 23 EXIT ASSIST FUNCTION : System Description 23 EXIT ASSIST FUNCTION : Component Parts Location .25 EXIT ASSIST FUNCTION : Component Description 26 AUTOMATIC DRIVE POSITIONER SYSTEM 11 ENTRY ASSIST FUNCTION 26 ENTRY ASSIST FUNCTION : System Diagram 27 ENTRY ASSIST FUNCTION : System Description 27 ENTRY ASSIST FUNCTION : Component Parts Location 29 ENTRY ASSIST FUNCTION : Component Description 30 AUTOMATIC DRIVE POSITIONER SYSTEM 11 INTELLIGENT KEY INTERLOCK FUNCTION 30 SYSTEM SETTING 10 SYSTEM SETTING : Description 10 SYSTEM SETTING : Special Repair Requirement 10 FUNCTION DIAGNOSIS 11 Revision: 2008 December ADP-1 J32 F G H I ADP K L M N O P INTELLIGENT KEY INTERLOCK FUNCTION : System Diagram 31 INTELLIGENT KEY INTERLOCK FUNCTION : System Description 31 INTELLIGENT KEY INTERLOCK FUNCTION : Component Parts Location 33 INTELLIGENT KEY INTERLOCK FUNCTION : Component Description 34 DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT) 35 Diagnosis Description 35 CONSULT-III Function 35 COMPONENT DIAGNOSIS 38 U1000 CAN COMM CIRCUIT 38 Description 38 DTC Logic 38 Diagnosis Procedure 38 Special Repair Requirement 38 U1010 CONTROL UNIT (CAN) 39 Description 39 DTC Logic 39 Diagnosis Procedure 39 B2130 EEPROM 40 DTC Logic 40 Diagnosis Procedure 40 B2112 SLIDING MOTOR 41 Description 41 DTC Logic 41 Diagnosis Procedure 41 B2113 RECLINING MOTOR 43 Description 43 DTC Logic 43 Diagnosis Procedure 43 POWER SUPPLY AND GROUND CIRCUIT 45 DRIVER SEAT CONTROL UNIT 45 DRIVER SEAT CONTROL UNIT : Diagnosis Procedure 45 SLIDING SWITCH 46 Diagnosis Procedure 50 Component Inspection 51 LIFTING SWITCH (REAR) 52 Description 52 Component Function Check 52 Diagnosis Procedure 52 Component Inspection 53 SEAT MEMORY SWITCH 54 Description 54 Component Function Check 54 Diagnosis Procedure 54 Component Inspection 55 POWER SEAT SWITCH GROUND CIRCUIT 57 Diagnosis Procedure 57 SLIDING SENSOR 58 Description 58 Component Function Check 58 Diagnosis Procedure 58 RECLINING SENSOR 61 Description 61 Component Function Check 61 Diagnosis Procedure 61 LIFTING SENSOR (FRONT) 64 Description 64 Component Function Check 64 Diagnosis Procedure 64 LIFTING SENSOR (REAR) 67 Description 67 Component Function Check 67 Diagnosis Procedure 67 SLIDING MOTOR 70 Description 70 Component Function Check 70 Diagnosis Procedure 70 RECLINING MOTOR 72 Description 72 Component Function Check 72 Diagnosis Procedure 72 Description 46 Component Function Check 46 Diagnosis Procedure 46 Component Inspection 47 LIFTING MOTOR (FRONT) 74 RECLINING SWITCH 48 LIFTING MOTOR (REAR) 76 Description 48 Component Function Check 48 Diagnosis Procedure 48 Component Inspection 49 Description 76 Component Function Check 76 Diagnosis Procedure 76 LIFTING SWITCH (FRONT) 50 Description 50 Component Function Check 50 Revision: 2008 December Description 74 Component Function Check 74 Diagnosis Procedure 74 SEAT MEMORY INDICATOR 78 Description 78 Component Function Check 78 Diagnosis Procedure 78 ADP-2 J32 ECU DIAGNOSIS 80 DRIVER SEAT CONTROL UNIT 80 SEAT RECLINING 148 SEAT RECLINING : Diagnosis Procedure 148 Reference Value 80 Wiring Diagram - AUTOMATIC DRIVE POSITIONER (LHD MODELS) - 85 Wiring Diagram - AUTOMATIC DRIVE POSITIONER (RHD MODELS) - 93 Fail-safe 100 DTC Index 101 SEAT LIFTING (FRONT) 148 SEAT LIFTING (FRONT) : Diagnosis Procedure 148 BCM (BODY CONTROL MODULE) 102 ENTRY/EXIT ASSIST FUNCTION DOES NOT OPERATE 151 Reference Value 102 Wiring Diagram - BCM - 126 Fail-safe 139 DTC Inspection Priority Chart 141 DTC Index 142 SYMPTOM DIAGNOSIS 144 MANUAL FUNCTION DOES NOT OPERATE 144 ALL COMPONENTS 144 ALL COMPONENTS : Diagnosis Procedure 144 SEAT SLIDING 144 SEAT SLIDING : Diagnosis Procedure 144 SEAT RECLINING 145 SEAT RECLINING : Diagnosis Procedure 145 SEAT LIFTING (FRONT) 145 SEAT LIFTING (FRONT) : Diagnosis Procedure 145 SEAT LIFTING (REAR) 146 SEAT LIFTING (REAR) : Diagnosis Procedure 146 MEMORY FUNCTION DOES NOT OPERATE 147 ALL COMPONENTS 147 ALL COMPONENTS : Diagnosis Procedure 147 SEAT SLIDING 147 SEAT SLIDING : Diagnosis Procedure 148 A B SEAT LIFTING (REAR) 149 SEAT LIFTING (REAR) : Diagnosis Procedure 149 MEMORY INDICATE DOES NOT OPERATE 150 C Diagnosis Procedure 150 D Diagnosis Procedure 151 INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE 152 E Diagnosis Procedure 152 NORMAL OPERATING CONDITION 153 F Description 153 PRECAUTION 154 G PRECAUTIONS 154 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 154 H ON-VEHICLE REPAIR 155 I DRIVER SEAT CONTROL UNIT 155 Exploded View 155 Removal and Installation 155 SEAT MEMORY SWITCH 156 ADP Exploded View 156 Removal and Installation 156 K POWER SEAT SWITCH 157 L Exploded View 157 Removal and Installation 157 M N O P Revision: 2008 December ADP-3 J32 DIAGNOSIS AND REPAIR WORK FLOW < BASIC INSPECTION > BASIC INSPECTION DIAGNOSIS AND REPAIR WORK FLOW Work Flow INFOID:0000000004296132 OVERALL SEQUENCE JMJIA1856GB DETAILED FLOW Revision: 2008 December ADP-4 J32 DIAGNOSIS AND REPAIR WORK FLOW < BASIC INSPECTION > 1.GET INFORMATION FOR SYMPTOM A Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurs) B >> GO TO 2.CHECK DTC WITH AUTOMATIC DRIVE POSITIONER SYSTEM C Check “Self Diagnostic Result” with CONSULT-III Refer to ADP-101, "DTC Index" Are any symptoms described and any DTC displayed? Symptom is described, DTC is detected.>>GO TO Symptom is not described, DTC is detected.>>GO TO Symptom is described, DTC is not detected.>>GO TO D 3.CONFIRM THE SYMPTOM E Try to confirm the symptom described by the customer F >> GO TO 4.CONFIRM THE SYMPTOM Try to confirm the symptom described by the customer G >> GO TO 5.CHECK NORMAL OPERATING CONDITION H Check normal operating condition Refer to ADP-153, "Description" Is the incident a normal operation? YES >> GO TO 10 NO >> GO TO I 6.PERFORM DTC CONFIRMATION PROCEDURE ADP Perform the confirmation procedure for the detected DTC Is the DTC displayed? YES >> GO TO NO >> Check intermittent incident Refer to GI-40, "Intermittent Incident" K 7.PERFORM COMPONENT FUNCTION CHECK L Perform the component function check for the isolated malfunctioning point M >> GO TO 8.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE Isolate the malfunctioning point by performing the diagnosis procedure relevant to the symptom during the component diagnosis >> GO TO N O 9.REPARE OR REPLACE Repair or replace the malfunctioning part P >> GO TO 10 10.FINAL CHECK Perform the DTC confirmation procedure (if DTC is detected) or component function check (if no DTC is detected) again Check that the malfunction is repaired Are all malfunctions repaired? Revision: 2008 December ADP-5 J32 DIAGNOSIS AND REPAIR WORK FLOW < BASIC INSPECTION > YES >> INSPECTION END Symptom is detected.>> GO TO DTC is detected.>> GO TO Revision: 2008 December ADP-6 J32 INSPECTION AND ADJUSTMENT < BASIC INSPECTION > INSPECTION AND ADJUSTMENT A ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Description B INFOID:0000000004296136 Each function is reset to the following condition when the battery terminal is disconnected C Function Memory (Seat) Condition Erased Procedure Perform memory storage D Perform system initialization Entry/exit assist OFF Intelligent Key interlock *1: Erased Set slide amount*1 Perform memory storage E Default value is 40mm NOTE: Notice that disconnecting the battery when detected DTC are present will erase the DTC memory F ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement G INFOID:0000000004296137 1.SYSTEM INITIALIZATION Perform system initialization Refer to ADP-8, "SYSTEM INITIALIZATION : Description" H >> GO TO 2.SYSTEM SETTING I Perform system setting Refer to ADP-10, "SYSTEM SETTING : Description" ADP >> GO TO 3.MEMORY STORAGE K Perform memory storage Refer to ADP-8, "MEMORY STORING : Description" >> END L ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description INFOID:0000000004296138 M Each function is reset to the following condition when the driver seat control unit is replaced Function Condition Memory (Seat) Erased Entry/exit assist OFF N Procedure Perform memory storage Perform system initialization O *1 Set slide amount Intelligent Key interlock *1: Erased Perform memory storage P Default value is 40 mm NOTE: Notice that disconnecting the battery when detected DTC are present will erase the DTC memory ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re- Revision: 2008 December ADP-7 J32 INSPECTION AND ADJUSTMENT < BASIC INSPECTION > quirement INFOID:0000000004296139 1.SYSTEM INITIALIZATION Perform system initialization Refer to ADP-8, "SYSTEM INITIALIZATION : Description" >> GO TO 2.SYSTEM SETTING Perform system setting Refer to ADP-10, "SYSTEM SETTING : Description" >> GO TO 3.MEMORY STORAGE Perform memory storage Refer to ADP-8, "MEMORY STORING : Description" >> END SYSTEM INITIALIZATION SYSTEM INITIALIZATION : Description INFOID:0000000004296140 Always perform the initialization when the battery terminal is disconnected or the driver seat control unit is replaced The entry/exit assist function will not operate normally unless initialization is performed SYSTEM INITIALIZATION : Special Repair Requirement INFOID:0000000004296141 INITIALIZATION PROCEDURE CHOOSE METHOD There are two initialization methods Which method you use? With door switch>>GO TO With vehicle speed>>GO TO STEP A-1 Turn ignition switch from the ACC to the OFF position >> GO TO 3 STEP A-2 Driver door switch is ON (open) → OFF (close) → ON (open) >> END STEP B-1 Drive the vehicle at more than 25 km/h (16 MPH) >> END MEMORY STORING MEMORY STORING : Description INFOID:0000000004296142 Always perform memory storage when the battery terminal is disconnected or the driver seat control unit is replaced The memory function and Intelligent Key interlock function will not operate normally unless memory storage is performed Revision: 2008 December ADP-8 J32 INSPECTION AND ADJUSTMENT < BASIC INSPECTION > MEMORY STORING : Special Repair Requirement INFOID:0000000004931030 A Memory Storage Procedure Two positions for the driver seat, steering column and outside mirror can be stored for memory operation by following procedure B 1.STEP Shift A/T selector lever to P position (A/T models) or applied parking brake (M/T models) C >> GO TO 2.STEP D Turn ignition switch ON E >> GO TO 3.STEP F Adjust driver seat, steering column and outside mirror position manually >> GO TO G 4.STEP Push set switch NOTE: H • Memory indicator for which driver seat position is already retained in memory is illuminated for seconds • Memory indicator for which driver seat position is not retained in memory is illuminated for 0.5 second I Push the memory switch (1 or 2) for at least second within seconds after pushing the set switch NOTE: • To enter driver seat positions into blank memory, memory indicator will be turned on for seconds • To modify driver seat positions, memory indicator will be turned OFF for 0.5 second, then turned ON for ADP seconds NOTE: If memory is stored in the same memory switch, the previous memory will be deleted K Do you need linking of Intelligent Key? YES >> GO TO NO >> GO TO L STEP 5 Confirm the operation of each part with memory operation M >> END 6.STEP N Turn ignition switch OFF O >> GO TO 7.STEP • Press and release set switch Memory switch indicator is illuminated for seconds During memory switch indicator is illuminated, press Intelligent Key unlock button while pressing memory switch or • Set switch indicator lamp is illuminated when completing registration >> GO TO 8.STEP Confirm the operation of each part with memory operation and Intelligent Key interlock operation Revision: 2008 December ADP-9 J32 P INSPECTION AND ADJUSTMENT < BASIC INSPECTION > >> END SYSTEM SETTING SYSTEM SETTING : Description INFOID:0000000004296144 The settings of the automatic driving positioner system can be changed, using CONSULT-III, the display unit in the center of the instrument panel and the set switch Always check the settings before and after disconnecting the battery terminal or replacing driver seat control unit Setting Change ×: Applicable Item Content CONSULT –III Set switch Factory setting Amount of seat sliding for entry/exit assist The amount of seat sliding for entry/exit assist can be selected from items [40mm/80mm/150mm] x — 40mm Entry/exit assist (seat) Entry/exit assist (seat) can be selected: ON (operated) – OFF (not operated) x x ON SYSTEM SETTING : Special Repair Requirement INFOID:0000000003888101 CHOOSE METHOD There are three ways of setting methods Which method you choose? With set switch>>GO TO With CONSULT-III>>GO TO WITH SET SWITCH - STEP Turn ignition switch OFF >> GO TO 3 WITH SET SWITCH - STEP Push setting button and hold for more than 10 seconds, then confirm blinking of the memory switch indicator • Entry/exit assist (seat) are ON: Memory switch indicator blinks two times • Entry/exit assist (seat) are OFF: Memory switch indicator blinks once >> END WITH CONSULT-III - STEP Select “Work support” >> GO TO 5 WITH CONSULT-III - STEP 2 Select “EXIT SEAT SLIDE SETTING”, or “SEAT SLIDE VOLUME SET” then touch display to change between ON and OFF EXIT SEAT SLIDE SETTING: Entry/exit assist (seat) Then touch “OK” >> END Revision: 2008 December ADP-10 J32 REAR DOOR LOCK [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > While pulling outside handle, remove outside handle escutcheon A B C JMKIA0560ZZ D While pulling outside handle (1), slide toward rear of vehicle to remove outside handle E F G JMKIA0524ZZ Remove rear door finisher Refer to INT-36, "Removal and Installation" Remove sealing screen Refer to GW-18, "Removal and Installation" Fully close rear door glass Remove front gasket and rear gasket While pulling outside handle bracket, slide toward rear of vehicle to remove outside handle bracket H I J DLK L JMKIA2303ZZ Reach in to separate outside handle cable connection on outside handle bracket M INSTALLATION Install in the reverse order of removal CAUTION: Check door open/close, lock/unlock operation after installation N O P Revision: 2008 December DLK-451 J32 TRUNK LID LOCK [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > TRUNK LID LOCK Exploded View INFOID:0000000004399468 JMKIA2389GB Trunk lid Trunk lid weather-strip Cap Stopper Bumper rubber Trunk lid hinge Trunk lid striker Trunk lid lock assembly A : Center mark (upper) B : Center mark (lower) Trunk lid stay Refer to GI-4, "Components" for symbols in the figure Removal and Installation INFOID:0000000004399469 REMOVAL Remove trunk lid finisher inner Refer to INT-63, "Removal and Installation" Disconnect trunk lid opener cable Disconnect trunk lid lock assembly and trunk lid opener switch connectors Remove mounting bolts and remove trunk lid lock assembly INSTALLATION Install in the reverse order of removal CAUTION: Check trunk lid open/close, lock/unlock operation after installation Revision: 2008 December DLK-452 J32 FUEL FILLER LID OPENER [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > FUEL FILLER LID OPENER A Exploded View INFOID:0000000004399470 B C D E F G H I JMKIA2390ZZ Fuel filler lid assembly Fuel filler lid opener actuator Bumper rubber Lock nut Removal and Installation J INFOID:0000000004399471 NOTE: When fuel filler lid opener actuator (1) is malfunctioning, pull the rod to open fuel filler lid DLK L M N JMKIA1960ZZ O REMOVAL Remove mounting screws, and then remove fuel filler lid Rotate lock nut counterclockwise, and then remove lock nut Push fuel filler lid opener actuator behind the vehicle, while pushing the pawl Remove rear wheel house finisher (LH) Refer to INT-61, "Exploded View" Disconnect harness connector and remove fuel filler lid opener actuator P INSTALLATION Install in the reverse order of removal CAUTION: Revision: 2008 December DLK-453 J32 FUEL FILLER LID OPENER [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > After installation, apply the touch-up paint (the body color) onto the head of the mounting screws Revision: 2008 December DLK-454 J32 DOOR SWITCH [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > DOOR SWITCH A Exploded View INFOID:0000000004400243 B C D JMKIA2569GB Door switch E Torx bolt Removal and Installation INFOID:0000000004400244 F REMOVAL G Remove the door switch torx bolt (A), and then remove door switch (1) H I JMKIA2173ZZ J INSTALLATION Install in the reverse order of removal DLK L M N O P Revision: 2008 December DLK-455 J32 OUTSIDE WARNING BUZZER [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > OUTSIDE WARNING BUZZER Exploded View INFOID:0000000004400257 JMKIA2435ZZ Outside warning buzzer Removal and Installation INFOID:0000000004400258 REMOVAL Remove the outside warning buzzer mounting nut (A), and then remove the outside warning buzzer (1) JMKIA2445ZZ INSTALLATION Install in the reverse order of removal Revision: 2008 December DLK-456 J32 KEY SLOT [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > KEY SLOT A Exploded View INFOID:0000000004400259 B C D E F JMKIA1820ZZ Key slot G Instrument lower panel Removal and Installation INFOID:0000000004400260 H REMOVAL Remove the instrument lower panel LH Refer to IP-12, "Removal and Installation" Disconnect key slot connector Remove the key slot mounting screws (A), and then remove key slot (1) from instrument lower panel LH I J DLK L JMKIA2351ZZ INSTALLATION M Install in the reverse order of removal N O P Revision: 2008 December DLK-457 J32 TRUNK LID OPENER REQUEST SWITCH [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > TRUNK LID OPENER REQUEST SWITCH Exploded View INFOID:0000000004400261 Refer to EXT-40, "Exploded View" Removal and Installation INFOID:0000000004400262 REMOVAL Remove the trunk lid finisher outer Refer to EXT-40, "Removal and Installation" Remove the trunk lid opener request switch mounting pawl (A), and then remove trunk lid opener request switch (1) from inner bracket : Pawl JMKIA2446ZZ INSTALLATION Install in the reverse order of removal Revision: 2008 December DLK-458 J32 TRUNK LID OPENER SWITCH [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > TRUNK LID OPENER SWITCH A Exploded View INFOID:0000000004400263 Refer to INT-63, "Exploded View" B Removal and Installation INFOID:0000000004400264 C REMOVAL Remove the instrument lower panel Refer to IP-12, "Removal and Installation" Remove the trunk lid opener switch from instrument driver lower panel, and then remove pawl Press trunk lid opener switch front side to disengage from instrument driver lower panel : D E Pawl F JMKIA2443ZZ G INSTALLATION Install in the reverse order of removal H I J DLK L M N O P Revision: 2008 December DLK-459 J32 REMOTE KEYLESS ENTRY RECEIVER [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > REMOTE KEYLESS ENTRY RECEIVER Exploded View INFOID:0000000004400265 JMKIA2178ZZ Remote keyless entry receiver Removal and Installation INFOID:0000000004400266 REMOVAL Remove the instrument lower panel RH Refer to IP-12, "Removal and Installation" Remove the remote keyless entry receiver mounting screws (A), and then remove remote keyless entry receiver (1) JMKIA2171ZZ INSTALLATION Install in the reverse order of removal Revision: 2008 December DLK-460 J32 KEYFOB BATTERY [WITHOUT INTELLIGENT KEY SYSTEM] < ON-VEHICLE REPAIR > KEYFOB BATTERY A Removal and Installation INFOID:0000000004400652 Release the lock knob at the back of the Intelligent Key and remove the mechanical key Insert a flat-blade screwdriver (A) wrapped with a cloth into the slit of the corner and twist it to separate the upper part from the lower part CAUTION: • Do not touch the circuit board or battery terminal • The key fob is water-resistant However, if it does get wet, immediately wipe it dry B C D E PIIB6221E F Replace the battery with new one Battery replacement :Coin-type lithium battery (CR2025) G Align the tips of the upper and lower parts, and then push them together until it is securely closed CAUTION: • When replacing battery, keep dirt, grease, and other foreign materials off the electrode contact area • After replacing the battery, check that all Intelligent Key functions work normally H I J PIIB6222E DLK L M N O P Revision: 2008 December DLK-461 J32 ENGINE SECTION ACC ACCELERATOR CONTROL SYSTEM A ACC C D E CONTENTS PRECAUTION ON-VEHICLE REPAIR PRECAUTIONS ACCELERATOR CONTROL SYSTEM Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" Exploded View Removal and Installation Inspection F G H I J K L M N O P Revision: 2008 December ACC-1 J32 PRECAUTIONS < PRECAUTION > PRECAUTION PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000004221778 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module, see the “SRS AIR BAG” • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury • When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the battery, and wait at least minutes before performing any service Revision: 2008 December ACC-2 J32 ACCELERATOR CONTROL SYSTEM < ON-VEHICLE REPAIR > ON-VEHICLE REPAIR A ACCELERATOR CONTROL SYSTEM Exploded View INFOID:0000000003801899 ACC C D E F G H I J JPBIA2204GB Accelerator pedal assembly : Vehicle front K Refer to GI-4, "Components" for symbols in the figure Removal and Installation INFOID:0000000003801900 L REMOVAL Disconnect accelerator pedal position sensor harness connector Loosen mounting bolts, and remove accelerator pedal assembly CAUTION: • Never disassemble accelerator lever Never remove accelerator pedal position sensor from accelerator lever • Avoid impact from dropping etc during handling • Be careful to keep accelerator lever away from water M N O INSTALLATION Note the following, and install in the reverse order of removal P Revision: 2008 December ACC-3 J32 ACCELERATOR CONTROL SYSTEM < ON-VEHICLE REPAIR > • Install the protrusion (A) of the bracket into the locating hole (B) of the accelerator pedal assembly before tightening the accelerator pedal assembly mounting bolts JPBIA2246ZZ Inspection INFOID:0000000003801901 INSPECTION AFTER INSTALLATION • Check accelerator pedal moves smoothly within the whole operation range when it is fully depressed and released • Check accelerator pedal securely returns to the fully released position • For the electrical inspection of accelerator pedal position sensor, refer to the following: - MR20DE (TYPE 1) EC-279, "Component Inspection", EC-282, "Component Inspection", and EC-290, "Component Inspection" - MR20DE (TYPE 2) EC-555, "Component Inspection", EC-558, "Component Inspection", and EC-566, "Component Inspection" - VQ25DE, VQ35DE (TYPE 1) EC-958, "Component Inspection", EC-961, "Component Inspection", and EC-968, "Component Inspection" - VQ25DE, VQ35DE (TYPE 2) EC-1314, "Component Inspection", EC-1317, "Component Inspection", and EC-1324, "Component Inspection" - CAUTION: When harness connector of accelerator pedal position sensor is disconnected, perform “Accelerator Pedal Released Position Learning” Refer to EC-29, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement" [MR20DE (TYPE 1)], EC-369, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement" [MR20DE (TYPE 2)], EC-661, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement" [VQ25DE, VQ35DE (TYPE 1)] or EC-1077, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement" [VQ25DE, VQ35DE (TYPE 2)] Revision: 2008 December ACC-4 J32