Tài liệu hướng dẫn sửa chữa xe Nissan altima hybrid esm tai lieu sua chua phan 1 . Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác, hiệu quả, hợp lý
ELECTRICAL & POWER CONTROL SECTION BCS BODY CONTROL SYSTEM A B C D E CONTENTS BCM BASIC INSPECTION DIAGNOSIS AND REPAIR WORKFLOW Work Flow ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement CONFIGURATION (BCM) CONFIGURATION (BCM) : Description CONFIGURATION (BCM) : Special Repair Requirement CONFIGURATION (BCM) : Configuration list FUNCTION DIAGNOSIS BODY CONTROL SYSTEM System Description Component Parts Location COMBINATION SWITCH READING SYSTEM 10 System Diagram 10 System Description 10 SIGNAL BUFFER SYSTEM .14 System Diagram 14 System Description 14 POWER CONSUMPTION CONTROL SYSTEM 15 System Diagram 15 System Description 15 Component Parts Location 17 DIAGNOSIS SYSTEM (BCM) 18 Revision: September 2009 F COMMON ITEM 18 COMMON ITEM : Diagnosis Description 18 COMMON ITEM : CONSULT-III Function (BCM COMMON ITEM) .18 G DOOR LOCK 19 DOOR LOCK : CONSULT-III Function (BCM DOOR LOCK) 19 H REAR WINDOW DEFOGGER 19 REAR WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER) .19 I BUZZER .20 BUZZER : CONSULT-III Function (BCM - BUZZER) 20 J INT LAMP 20 INT LAMP : CONSULT-III Function (BCM - INT LAMP) 20 K HEADLAMP .22 HEADLAMP : CONSULT-III Function (BCM HEAD LAMP) 22 L WIPER 24 WIPER : CONSULT - III Function (BCM - WIPER) 24 BCS FLASHER 24 FLASHER : CONSULT-III Function (BCM FLASHER) .24 N AIR CONDITIONER 25 AIR CONDITIONER : CONSULT-III Function 25 O INTELLIGENT KEY 25 INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) 25 P COMB SW 28 COMB SW : CONSULT-III Function (BCM COMB SW) 28 BCM 29 BCS-1 2010 Altima HEV BCM : CONSULT-III Function (BCM - BCM) 29 Special Repair Requirement 40 IMMU 29 IMMU : CONSULT-III Function (BCM - IMMU) 29 POWER SUPPLY AND GROUND CIRCUIT 41 BATTERY SAVER 30 BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER) 30 TRUNK 31 TRUNK : CONSULT-III Function (BCM - TRUNK) 31 THEFT ALM 31 THEFT ALM : CONSULT-III Function (BCM THEFT) 31 RETAINED PWR 32 RETAINED PWR : CONSULT-III Function (BCM RETAINED PWR) 32 SIGNAL BUFFER 32 SIGNAL BUFFER : CONSULT-III Function 32 AIR PRESSURE MONITOR 33 AIR PRESSURE MONITOR : Diagnosis Description 33 AIR PRESSURE MONITOR : CONSULT-III Function (BCM - AIR PRESSURE MONITOR) 34 COMPONENT DIAGNOSIS 36 U1000 CAN COMM CIRCUIT 36 Diagnosis Procedure 41 Special Repair Requirement 41 COMBINATION SWITCH INPUT CIRCUIT 42 Diagnosis Procedure 42 Special Repair Requirement 43 COMBINATION SWITCH OUTPUT CIRCUIT 44 Diagnosis Procedure 44 Special Repair Requirement 45 ECU DIAGNOSIS 46 BCM (BODY CONTROL MODULE) 46 Reference Value 46 Terminal Layout 50 Physical Values 50 Fail Safe 66 DTC Inspection Priority Chart 67 DTC Index 68 WIRING DIAGRAM 71 BCM (BODY CONTROL MODULE) 71 Wiring Diagram 71 SYMPTOM DIAGNOSIS 80 Description 36 DTC Logic 36 Diagnosis Procedure 36 COMBINATION SWITCH SYSTEM SYMPTOMS 80 U1010 CONTROL UNIT (CAN) 37 PRECAUTION 81 DTC Logic 37 Diagnosis Procedure 37 PRECAUTIONS 81 U0415 VEHICLE SPEED SIG 38 Symptom Table 80 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 81 Description 38 DTC Logic 38 Diagnosis Procedure 38 PREPARATION 82 B2562 LOW VOLTAGE 39 PREPARATION 82 DTC Logic 39 Diagnosis Procedure 39 Special Repair Requirement 39 B2563 HI VOLTAGE 40 DTC Logic 40 Diagnosis Procedure 40 Revision: September 2009 Commercial Service Tools 82 ON-VEHICLE REPAIR 83 BCM (BODY CONTROL MODULE) 83 Removal and Installation 83 BCS-2 2010 Altima HEV DIAGNOSIS AND REPAIR WORKFLOW [BCM] < BASIC INSPECTION > BASIC INSPECTION A DIAGNOSIS AND REPAIR WORKFLOW Work Flow INFOID:0000000005438890 B OVERALL SEQUENCE C D E F G H I J K L BCS N O P JMKIA0101GB DETAILED FLOW Revision: September 2009 BCS-3 2010 Altima HEV DIAGNOSIS AND REPAIR WORKFLOW [BCM] < BASIC INSPECTION > GET INFORMATION FOR SYMPTOM Get the detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred) >> GO TO 2 CHECK DTC Check DTC Perform the following procedure if DTC is displayed Record DTC and freeze frame data Erase DTC Study the relationship between the cause detected by DTC and the symptom described by the customer Check related service bulletins for information Is any symptom described and any DTC detected? Symptom is described, DTC is detected>>GO TO Symptom is described, DTC is not detected>>GO TO Symptom is not described, DTC is detected>>GO TO CONFIRM THE SYMPTOM Confirm the symptom described by the customer Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real time diagnosis results Verify relation between the symptom and the condition when the symptom is detected >> GO TO CONFIRM THE SYMPTOM Confirm the symptom described by the customer Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real time diagnosis results Verify relation between the symptom and the condition when the symptom is detected >> GO TO PERFORM DTC CONFIRMATION PROCEDURE Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again At this time, always connect CONSULT-III to the vehicle, and check diagnostic results in real time If two or more DTCs are detected, refer to BCS-67, "DTC Inspection Priority Chart" and determine trouble diagnosis order NOTE: • Freeze frame data is useful if the DTC is not detected • Perform Component Function Check if DTC Confirmation Procedure is not included in Service Manual This simplified check procedure is an effective alternative though DTC cannot be detected during this check If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation Procedure Is DTC detected? YES >> GO TO NO >> Refer to BCS-68, "DTC Index" PERFORM BASIC INSPECTION Perform BCS-3, "Work Flow" Inspection End>>GO TO 7 DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE Detect malfunctioning system according to BCS-8, "System Description" based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom >> GO TO Revision: September 2009 BCS-4 2010 Altima HEV DIAGNOSIS AND REPAIR WORKFLOW [BCM] < BASIC INSPECTION > DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE A Inspect according to Diagnostic Procedure of the system NOTE: The Diagnostic Procedure described based on open circuit inspection A short circuit inspection is also required for the circuit check in the Diagnostic Procedure Is malfunctioning part detected? YES >> GO TO NO >> Check voltage of related BCM terminals using CONSULT-III B C REPAIR OR REPLACE THE MALFUNCTIONING PART Repair or replace the malfunctioning part Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replacement Check DTC If DTC is displayed, erase it D E >> GO TO 10 10 FINAL CHECK F When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check again, and then check that the malfunction have been repaired securely When symptom was described from the customer, refer to confirmed symptom in step or 4, and check that the symptom is not detected Does the symptom reappear? YES (DTC is detected)>>GO TO YES (Symptom remains)>>GO TO NO >> Inspection End ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT G H I ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description INFOID:0000000005438891 J BEFORE REPLACEMENT When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before replacement NOTE: If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after replacing BCM K L AFTER REPLACEMENT CAUTION: • When replacing BCM, you must perform “WRITE CONFIGURATION” with CONSULT-III - Complete the procedure of “WRITE CONFIGURATION” in order - If you set incorrect “WRITE CONFIGURATION”, incidents might occur - Configuration is different for each vehicle model Confirm configuration of each vehicle model • When replacing BCM, perform the system initialization (NATS) ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement INFOID:0000000005438892 BCS N O SAVING VEHICLE SPECIFICATION CONSULT-III Configuration Perform “READ CONFIGURATION” to save or print current vehicle specification Refer to BCS-6, "CONFIGURATION (BCM) : Description" NOTE: If “READ CONFIGURATION” cannot be used, use the “WRITE CONFIGURATION - Manual selection” after replacing BCM Revision: September 2009 BCS-5 2010 Altima HEV P DIAGNOSIS AND REPAIR WORKFLOW [BCM] < BASIC INSPECTION > >> GO TO 2 REPLACE BCM Replace BCM Refer to BCS-83, "Removal and Installation" >> GO TO 3 WRITING VEHICLE SPECIFICATION CONSULT-III Configuration Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write vehicle specification Refer to BCS-6, "CONFIGURATION (BCM) : Special Repair Requirement" >> GO TO 4 INITIALIZE BCM (NATS) Perform BCM initialization (NATS) Refer to CONSULT-III Operation Manual >> Inspection End CONFIGURATION (BCM) CONFIGURATION (BCM) : Description INFOID:0000000005438893 Vehicle specification needs to be written with CONSULT-III because it is not written after replacing BCM Configuration has three functions as follows Function Description READ CONFIGURATION • Reads the vehicle configuration of current BCM • Saves the read vehicle configuration WRITE CONFIGURATION - Manual selection Writes the vehicle configuration with manual selection WRITE CONFIGURATION - Config file Writes the vehicle configuration with saved data NOTE: Manual setting item: Items which need selection by vehicle specifications Automatic setting item: Items which are written in automatically (Setting cannot be changed) CAUTION: • When replacing BCM, you must perform “WRITE CONFIGURATION” with CONSULT-III • Complete the procedure of “WRITE CONFIGURATION” in order • If you set incorrect “WRITE CONFIGURATION”, incidents might occur • Configuration is different for each vehicle model Confirm configuration of each vehicle model • Never perform “WRITE CONFIGURATION” except for new BCM CONFIGURATION (BCM) : Special Repair Requirement INFOID:0000000005438894 WRITING MODE SELECTION CONSULT-III Configuration Select “CONFIGURATION” of BCM When writing saved data>>GO TO When writing manually>>GO TO PERFORM “WRITE CONFIGURATION - CONFIG FILE” CONSULT-III Configuration Perform “WRITE CONFIGURATION - Config File” >> Inspection End Revision: September 2009 BCS-6 2010 Altima HEV DIAGNOSIS AND REPAIR WORKFLOW [BCM] < BASIC INSPECTION > PERFORM “WRITE CONFIGURATION - MANUAL SELECTION” A CONSULT-III Configuration Select "WRITE CONFIGURATION - Manual selection" Identify the correct model and configuration list Refer to BCS-7, "CONFIGURATION (BCM) : Configuration list" Confirm and/or change setting value for each item Select "Setting change" CAUTION: Make sure to select “Setting change” even if the indicated configuration of brand new BCM is same as the desirable configuration If not, configuration which is set automatically by selecting vehicle model cannot be memorized When "COMMAND FINISHED", select "END" >> GO TO B C D E OPERATION CHECK Confirm that each function controlled by BCM operates normally F >> Inspection End CONFIGURATION (BCM) : Configuration list MANUAL SETTING ITEM INFOID:0000000005438895 H NOTE Items Setting value AUTO LIGHT WITH⇔WITHOUT DTRL WITH⇔WITHOUT TRANSMISSION HEV — TR CANCEL SW WITH⇔WITHOUT — TIRE PRESSURE 240 kPa — G — I • WITH: Canada • WITHOUT: Except Canada J K L BCS N O P Revision: September 2009 BCS-7 2010 Altima HEV BODY CONTROL SYSTEM [BCM] < FUNCTION DIAGNOSIS > FUNCTION DIAGNOSIS BODY CONTROL SYSTEM System Description INFOID:0000000005438896 OUTLINE • BCM (body control module) controls the various electrical components It inputs the information required to the control from CAN communication and the signal received from each switch and sensor • BCM has combination switch reading function for reading the operation status of combination switches (light, turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical components It also has the signal transmission function as the passed point of signal and the power saving control function that reduces the power consumption with the ignition switch OFF • BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various settings CAN communication control In CAN communication, control units are connected with communication lines (CAN-L, CAN-H) allowing a high rate of information transmission with less wiring Each control unit transmits/receives the data but selectively reads required information only CAN communication signal Refer to the LAN-28, "CAN Communication Signal Chart" BCM control function list System Refer to Combination switch reading system BCS-10, "System Description" Signal buffer system BCS-14, "System Description" Power consumption control system BCS-15, "System Description" Auto light system EXL-12, "System Description" Turn signal and hazard warning lamp system EXL-15, "System Description" Headlamp system EXL-7, "System Description" Exterior lamp battery saver system PCS-11, "System Description" Daytime running light system (Canada only) EXL-9, "System Description" Interior room lamp control system Step lamp system INL-6, "System Description" Interior room lamp battery saver system BCS-15, "System Description" Front wiper and washer system WW-6, "System Description" Warning chime system WCS-4, "WARNING CHIME SYSTEM : System Description" Door lock system DLK-13, "DOOR LOCK AND UNLOCK SWITCH : System Description" Trunk open system DLK-26, "TRUNK LID OPENER SWITCH : System Description" Nissan vehicle immobilizer system SEC-15, "System Description" Vehicle security system Panic alarm Rear window defogger system Revision: September 2009 SEC-18, "System Description" DEF-6, "System Description" BCS-8 2010 Altima HEV BODY CONTROL SYSTEM [BCM] < FUNCTION DIAGNOSIS > System Refer to A Door lock function • DLK-15, "DOOR REQUEST SWITCH : System Description" (door request switch) • SEC-10, "System Description" (Intelligent Key) B Trunk open function • DLK-26, "TRUNK LID OPENER SWITCH : System Description" (trunk request switch) • SEC-10, "System Description" (Intelligent Key) Warning function DLK-38, "System Description" C Key reminder function DLK-44, "System Description" Hybrid system start function SEC-10, "System Description" Intelligent Key system/hybrid system start D Power window system • PWC-94, "System Description" (LH & RH front window antipinch) • PWC-11, "System Description" (LH front only window antipinch) RAP (retained accessory power) system RF-8, "System Description" TPMS (tire pressure monitor system) WT-8, "System Description" Component Parts Location E F INFOID:0000000005438897 G H I J K L ALCIA0020ZZ BCM M16, M17, M18, M19, M20, M21 (view with instrument panel removed) BCS N O P Revision: September 2009 BCS-9 2010 Altima HEV COMBINATION SWITCH READING SYSTEM [BCM] < FUNCTION DIAGNOSIS > COMBINATION SWITCH READING SYSTEM System Diagram INFOID:0000000005438898 ABMIA1836GB System Description INFOID:0000000005438899 OUTLINE • BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the status of each switch • BCM is a combination of output terminals (OUTPUT - 5) and input terminals (INPUT - 5) It reads a maximum of 20 switch status COMBINATION SWITCH MATRIX Combination switch circuit ABMIA1837GB Combination switch INPUT-OUTPUT system list System OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT INPUT — FR WASHER FR WIPER LOW TURN LH TURN RH INPUT FR WIPER HI — FR WIPER INT PASSING HEADLAMP INPUT INT VOLUME — — HEADLAMP HI BEAM Revision: September 2009 BCS-10 2010 Altima HEV USB CONNECTOR [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > USB CONNECTOR Removal and Installation INFOID:0000000005818899 Removal Remove the center console assembly Refer to IP-14, "Removal and Installation" Push the pawl from the back of the center console to remove the USB connector (1) ALNIA1238ZZ Installation Installation is in the reverse order of removal Revision: Revision: JulyJune 20102010 AV-294 2010 Altima HEV 2010 Altima HEV AUXILIARY INPUT JACKS [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > AUXILIARY INPUT JACKS A Removal and Installation INFOID:0000000005818900 REMOVAL B C Remove the center console Refer to IP-14, "Removal and Installation" Remove the center console bin box Disconnect the auxiliary input jacks connector (B) Remove the auxiliary input jacks screws (A) Remove the auxiliary input jacks (1) D E F ALNIA1240ZZ INSTALLATION Installation is in the reverse order of removal G H I J K L M AV O P Revision: Revision: JulyJune 20102010 AV-295 2010 Altima HEV 2010 Altima HEV TWEETER [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > TWEETER Removal and Installation INFOID:0000000005438871 REMOVAL Remove the front pillar finisher Refer to INT-26, "Removal and Installation" Remove tweeter speaker grille Refer to IP-11, "Removal and Installation" Remove the tweeter speaker screws (A), disconnect the tweeter speaker connector and remove the tweeter speaker (1) ALNIA0180GB INSTALLATION Installation is in the reverse order of removal Revision: Revision: JulyJune 20102010 AV-296 2010 Altima HEV 2010 Altima HEV CENTER SPEAKER [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > CENTER SPEAKER A Removal and Installation INFOID:0000000005438872 REMOVAL B Remove the center speaker grille Refer to IP-11, "Removal and Installation" Remove the center speaker screws (A), then pull out the center speaker (1), disconnect the connector and remove the center speaker (1) C D E ALNIA0181GB F INSTALLATION Installation is in the reverse order of removal G H I J K L M AV O P Revision: Revision: JulyJune 20102010 AV-297 2010 Altima HEV 2010 Altima HEV FRONT DOOR SPEAKER [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > FRONT DOOR SPEAKER Removal and Installation INFOID:0000000005438873 REMOVAL Remove the front door finisher Refer to INT-13, "Removal and Installation" Remove the front door speaker screws (A), then disconnect the front door speaker connector and remove the front door speaker (1) ALNIA0040ZZ INSTALLATION Installation is in the reverse order of removal Revision: Revision: JulyJune 20102010 AV-298 2010 Altima HEV 2010 Altima HEV REAR DOOR SPEAKER [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > REAR DOOR SPEAKER A Removal and Installation INFOID:0000000005438874 REMOVAL B Remove the rear door finisher Refer to INT-13, "Removal and Installation" Remove the rear door speaker screws (A), then disconnect the rear door speaker connector and remove the rear door speaker (1) C D E ALNIA0041ZZ F INSTALLATION Installation is in the reverse order of removal G H I J K L M AV O P Revision: Revision: JulyJune 20102010 AV-299 2010 Altima HEV 2010 Altima HEV SUBWOOFER [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > SUBWOOFER Removal and Installation INFOID:0000000005438875 REMOVAL Remove the rear parcel shelf finisher Refer to INT-22, "Removal and Installation" Remove the rear subwoofer screws (A), then disconnect the rear subwoofer connector and remove the rear subwoofer (1) ALNIA0042ZZ INSTALLATION Installation is in the reverse order of removal Revision: Revision: JulyJune 20102010 AV-300 2010 Altima HEV 2010 Altima HEV AUDIO ANTENNA [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > AUDIO ANTENNA A Location of Antennas INFOID:0000000005438876 B C D E F G H I J K L M AWNIA2144ZZ AV control unit harness connector AV control unit harness AV control unit Roof antenna rod Roof antenna base Antenna feeder (to AV control unit) Window antenna Roof Antenna AV INFOID:0000000005438877 O REMOVAL AND INSTALLATION P Removal Remove the rear parcel shelf finisher Refer to INT-22, "Removal and Installation" Remove the rear assist grips Refer to INT-26, "Removal and Installation" Pull down headlining (rear) and obtain space work between roof and headlining Revision: Revision: JulyJune 20102010 AV-301 2010 Altima HEV 2010 Altima HEV AUDIO ANTENNA [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > Remove the roof antenna nut (A), then disconnect the antenna feeder connector (B) and remove the antenna feeder (1) from the roof Detach the antenna feeder harness wire clips, then disconnect the antenna feeder harness wire end and feed the antenna feeder harness through the roof to remove the roof antenna base ALNIA0127ZZ Installation Installation is in the reverse order of removal Window Antenna Repair INFOID:0000000005438878 ELEMENT CHECK Attach probe circuit tester (ohm setting) to antenna terminal on each side SEL250I • When measuring continuity, wrap tin foil around the top of probe Then, press the foil against the wire with your finger SEL122R Revision: Revision: JulyJune 20102010 AV-302 2010 Altima HEV 2010 Altima HEV AUDIO ANTENNA < ON-VEHICLE REPAIR > If an element is broken, no continuity will exist [BOSE AUDIO WITH NAVIGATION] A B C D E F G SEL252I To locate a break, move probe along element Tester indication will change abruptly when probe passes the broken point H I J SEL253I K REPAIR EQUIPMENT • • • • • • Conductive silver composition (DuPont No 4817 or equivalent) Ruler 30 cm (11.8 in) long Drawing pen Heat gun Alcohol Cloth L M REPAIRING PROCEDURE Wipe broken heat wire and its surrounding area clean with a cloth dampened in alcohol Apply a small amount of conductive silver composition to tip of drawing pen Shake silver composition container before use Place ruler on glass along broken line Deposit conductive silver composition on break with drawing pen Slightly overlap existing heat wire on both sides [preferably mm (0.20 in)] of the break AV O P PIIA0215E Revision: Revision: JulyJune 20102010 AV-303 2010 Altima HEV 2010 Altima HEV AUDIO ANTENNA [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > After repair has been completed, check repaired wire for continuity This check should be conducted 10 minutes after silver composition is deposited Do not touch repaired area while test is being conducted SEL012D Apply a constant stream of hot air directly to the repaired area for approximately 20 minutes with a heat gun A minimum distance of cm (1.2 in) should be kept between repaired area and hot air outlet If a heat gun is not available, let the repaired area dry for 24 hours SEL013D Revision: Revision: JulyJune 20102010 AV-304 2010 Altima HEV 2010 Altima HEV GPS ANTENNA [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > GPS ANTENNA A Removal and Installation INFOID:0000000005438879 REMOVAL B Remove the combination meter Refer to IP-11, "Removal and Installation" Remove the navigation audio unit Refer to AV-292, "Removal and Installation" Remove the GPS navigation antenna screw (A), then fish the GPS navigation antenna connector and harness (1), through the combination meter instrument panel opening and remove the GPS antenna C D E F ALNIA0061ZZ INSTALLATION G Installation is in the reverse order of removal H I J K L M AV O P Revision: Revision: JulyJune 20102010 AV-305 2010 Altima HEV 2010 Altima HEV STEERING SWITCH [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > STEERING SWITCH Removal and Installation INFOID:0000000005438880 REMOVAL Remove the driver airbag module Refer to SR-4, "Removal and Installation" Remove the steering wheel switch assembly screws (A), then remove the steering wheel switches (1) ALNIA0045ZZ INSTALLATION Installation is in the reverse order of removal Revision: Revision: JulyJune 20102010 AV-306 2010 Altima HEV 2010 Altima HEV MICROPHONE [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > MICROPHONE A Removal and Installation INFOID:0000000005438881 REMOVAL B Remove the room/map lamp assembly Refer to INT-26, "Exploded View" Detach the microphone connector (A) C D E ALNIA0928ZZ F Remove the map lamp covers (1), then remove the map lamp assembly cover (2) G H I ALNIA0929ZZ Release the microphone tabs (A), then remove the microphone (1) J K L M ALNIA0930ZZ INSTALLATION Installation is in the reverse order of removal AV O P Revision: Revision: JulyJune 20102010 AV-307 2010 Altima HEV 2010 Altima HEV REAR VIEW CAMERA [BOSE AUDIO WITH NAVIGATION] < ON-VEHICLE REPAIR > REAR VIEW CAMERA Removal and Installation INFOID:0000000005438882 REMOVAL Remove the license plate finisher Refer to EXT-25, "Removal and Installation" Remove the trunk lid finisher Refer to INT-30, "Removal and Installation" Disconnect the rear view camera connector (B), press the rear view camera tab (A) and remove the rear view camera (1) ALNIA0062ZZ INSTALLATION Installation is in the reverse order of removal Adjustment INFOID:0000000005438883 REAR VIEW MONITOR For adjustment on the rear view camera, refer to AV-68, "Diagnosis Description" Revision: Revision: JulyJune 20102010 AV-308 2010 Altima HEV 2010 Altima HEV