Tài liệu hướng dẫn sửa chữa Hệ thống 2 cầu trê xe Hilux 2015 2018 manual vf2cm transfer 4wd awd he thong 2 cau . Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác, hiệu quả
Print-Toyota Service Information 11/3/17, 7'52 pm Print Exit VF2CM TRANSFER / 4WD / AWD 4WD CONTROL ECU COMPONENTS ILLUSTRATION *1 WHEEL DRIVE CONTROL ECU N*m (kgf*cm, ft.*lbf): Specified torque *2 - ECM - © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-j…manual/repair/contents/RM100000000M1SO.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'52 pm Print Exit VF2CM TRANSFER / 4WD / AWD 4WD CONTROL ECU INSTALLATION CAUTION / NOTICE / HINT HINT: · · Use the same procedure for RHD and LHD vehicles The procedure listed below is for LHD vehicles PROCEDURE 1.INSTALL WHEEL DRIVE CONTROL ECU a 89533 Install the wheel drive control ECU with the nut Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf) 2.INSTALL ECM · · · · · · · for for for for for for for 89661 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>ECM>INSTALLATION 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>INSTALLATION 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>INSTALLATION 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>INSTALLATION 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>INSTALLATION 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>INSTALLATION 5L-E: Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>ECM>INSTALLATION © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-j…manual/repair/contents/RM100000000TFTZ.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'52 pm Print Exit VF2CM TRANSFER / 4WD / AWD 4WD CONTROL ECU REMOVAL CAUTION / NOTICE / HINT The necessary procedures(adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the wheel drive control ECU removal/installation are shown below Necessary Procedure After Parts Removed/Installed/Replaced Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed for 1GR-FE: VIN registration or DTC P0630 is output frame number registration for 2TR-FE: VIN registration or DTC P0630 is output frame number registration Link Click here( ) Click here( ) for 1GD-FTV: Click here( for 1GD-FTV, 2GD-FTV: · Learning Values Save · Learning Values Write · VIN registration · · Engine starting DTC P0630 is output ) for 1GD-FTV, w/ DPF: Click here( ) for 2GD-FTV: Click here( ) for 2GD-FTV, w/ DPF: Click here( ECM for 1KD-FTV, 2KD-FTV: · Learning Values Save Engine starting · Learning Values Write · VIN registration for 5L-E: VIN registration or frame number registration Performing iMT installation information reset Code registration (Immobiliser system) · · Engine starting DTC P0630 is output · · iMT system DTCs are output Engine start function ) for 1KD-FTV: Click here( ) for 2KD-FTV: Click here( ) Click here( ) Click here( ) See the Service Bulletin for the registration method HINT: · · Use the same procedure for RHD and LHD vehicles The procedure listed below is for LHD vehicles PROCEDURE 1.REMOVE ECM 89661 https://toyotamanuals.com.au/docs/hilux-service-repair-manual-j…manual/repair/contents/RM100000000TFTY.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information · · · · · · · for for for for for for for 11/3/17, 7'52 pm 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>ECM>REMOVAL 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL 5L-E: Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>ECM>REMOVAL 2.REMOVE WHEEL DRIVE CONTROL ECU 89533 a Remove the nut and wheel drive control ECU © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-j…manual/repair/contents/RM100000000TFTY.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'51 pm Print Exit VF2CM TRANSFER / 4WD / AWD 4WD CONTROL SWITCH COMPONENTS ILLUSTRATION *A *1 for Automatic Air Conditioning System AIR CONDITIONING CONTROL ASSEMBLY *2 TRANSFER POSITION SWITCH ILLUSTRATION https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…manual/repair/contents/RM100000000M1SH.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information *A *1 for Manual Air Conditioning System INTEGRATION PANEL SUB-ASSEMBLY 11/3/17, 7'51 pm *2 TRANSFER POSITION SWITCH © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…manual/repair/contents/RM100000000M1SH.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'52 pm Print Exit VF2CM TRANSFER / 4WD / AWD 4WD CONTROL SWITCH INSTALLATION CAUTION / NOTICE / HINT HINT: · · Use the same procedure for RHD and LHD vehicles The procedure listed below is for LHD vehicles PROCEDURE 1.INSTALL TRANSFER POSITION SWITCH a 84223A Attach the claws to install the transfer position switch 2.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System) 55900 Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL(for Automatic Air Conditioning System)>INSTALLATION 3.INSTALL INTEGRATION PANEL SUB-ASSEMBLY (for Manual Air Conditioning System) 84013A Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL(for Manual Air Conditioning System)>INSTALLATION © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-j…manual/repair/contents/RM100000000M1SJ.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'51 pm Print Exit VF2CM TRANSFER / 4WD / AWD 4WD CONTROL SWITCH REMOVAL CAUTION / NOTICE / HINT HINT: · · Use the same procedure for RHD and LHD vehicles The procedure listed below is for LHD vehicles PROCEDURE 1.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System) 55900 Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL(for Automatic Air Conditioning System)>REMOVAL 2.REMOVE INTEGRATION PANEL SUB-ASSEMBLY (for Manual Air Conditioning System) 84013A Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL(for Manual Air Conditioning System)>REMOVAL 3.REMOVE TRANSFER POSITION SWITCH 84223A a *A *B for Automatic Air Conditioning System for Manual Air Conditioning System https://toyotamanuals.com.au/docs/hilux-service-repair-manual-j…manual/repair/contents/RM100000000M1SI.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'51 pm Detach the claws and remove the transfer position switch © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-j…manual/repair/contents/RM100000000M1SI.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'48 pm Print Exit VF2CM TRANSFER / 4WD / AWD TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM PROBLEM SYMPTOMS TABLE HINT: · · Use the table below to help determine the cause of problem symptoms If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table Check each symptom by checking the suspected areas in the order they are listed Replace parts as necessary Inspect the fuses and relays related to this system before inspecting the suspected areas below Touch Select 2-4 and High-low System Symptom Suspected Area While in 2WD, even when the transfer position switch is turned to a position other than H2, the 4WD indicator light (green) and 4LO indicator light not illuminate ECU power source circuit While in 4WD, even when the transfer position switch is turned to a position other than H4, the 4WD indicator light (green) remains on and the 4LO indicator light does not illuminate ECU power source circuit While in 4WD, even when the transfer position switch is turned to a position other than L4, the 4WD indicator light (green) and 4LO indicator light remain illuminated ECU power source circuit Link CAN communication system Combination meter assembly Transfer position switch wheel drive control ECU Clutch start switch circuit (for Manual Transmission) Transfer position switch wheel drive control ECU Transfer position switch wheel drive control ECU CAN communication system ECU power source circuit Transfer shift actuator assembly (transfer shift motor) A.D.D actuator (differential motor actuator assembly) (A.D.D shift motor)* The 4WD indicator light (green) continues blinking after the Transfer shift actuator assembly transfer position switch is operated (limit switch, 4WD detection switch or L4 detection switch) A.D.D actuator (differential motor actuator assembly) (limit switch or A.D.D position switch)* wheel drive control ECU ECU power source circuit Clutch start switch circuit (for Manual Transmission) The 4LO indicator light continues blinking after the transfer position switch is operated Transfer shift actuator assembly (transfer shift motor) Transfer shift actuator assembly (limit switch, 4WD detection switch or L4 detection switch) wheel drive control ECU *: w/ A.D.D Actuator https://toyotamanuals.com.au/docs/hilux-service-repair-manual-j…manual/repair/contents/RM100000000LTLP.html?PUB_TYPE=RM&MODE=1 Page of