Tài liệu hướng dẫn sửa chữa Hệ thống dẫn động trên xe Hilux 2015 2018 manual drive shaft propeller shaft he thong dan dong . Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác
Print-Toyota Service Information 11/3/17, 7'53 pm Print Exit DRIVE SHAFT / PROPELLER SHAFT DRIVE SHAFT SYSTEM PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table Check each symptom by checking the suspected areas in the order they are listed Replace parts as necessary Drive Shaft System Symptom Front wheel shimmy Suspected Area Link Front drive shaft (worn) © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…manual/repair/contents/RM100000000M5SK.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'54 pm Print Exit DRIVE SHAFT / PROPELLER SHAFT FRONT DRIVE SHAFT ASSEMBLY COMPONENTS ILLUSTRATION *1 NO ENGINE UNDER COVER N*m (kgf*cm, ft.*lbf): Specified torque *2 - NO ENGINE UNDER COVER - ILLUSTRATION https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M5SN.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information *1 *3 *5 *7 ● FRONT AXLE HUB GREASE CAP LH FRONT DRIVE SHAFT ASSEMBLY LH FRONT LOWER SUSPENSION ARM ASSEMBLY LH TIE ROD END SUB-ASSEMBLY LH 11/3/17, 7'54 pm *2 *4 FRONT AXLE SHAFT NUT LH FRONT DRIVE SHAFT HOLE SNAP RING *6 FRONT SPEED SENSOR LH *8 LOCK CAP Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque Non-reusable part Differential oil https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M5SN.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'54 pm MP grease Do not apply lubricants to the threaded parts ILLUSTRATION *1 FRONT AXLE HUB DUST SEAL *2 FRONT AXLE INBOARD JOINT BOOT CLAMP LH https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M5SN.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'54 pm *3 FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH *4 FRONT DRIVE SHAFT DUST COVER LH *5 FRONT NO AXLE INBOARD JOINT BOOT CLAMP LH *6 FRONT NO AXLE OUTBOARD JOINT BOOT CLAMP LH *7 INBOARD JOINT *8 INBOARD JOINT BOOT *9 *11 ● OUTBOARD JOINT BOOT TRIPOD Non-reusable part *10 *12 - SNAP RING FRONT DRIVE OUTBOARD JOINT ASSEMBLY - © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M5SN.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'59 pm Print Exit DRIVE SHAFT / PROPELLER SHAFT FRONT DRIVE SHAFT ASSEMBLY DISASSEMBLY CAUTION / NOTICE / HINT NOTICE: · · When using a vise, place aluminum plates between the part and vise When using a vise, not overtighten it HINT: · · Use the same procedure for the RH and LH sides The procedure listed below is for the LH side PROCEDURE 1.DISCONNECT FRONT NO AXLE INBOARD JOINT BOOT CLAMP LH *a a 43448G Claw Engagement Using needle-nose pliers, detach the claw engagement and disconnect the front No axle inboard joint boot clamp LH as shown in the illustration 2.DISCONNECT FRONT AXLE INBOARD JOINT BOOT CLAMP LH 43448F a Using pliers, grasp and move the front axle inboard joint boot clamp LH as shown in the illustration to disconnect it from the inboard joint boot https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…manual/repair/contents/RM100000000M5SP.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'59 pm 3.DISCONNECT INBOARD JOINT BOOT a Disconnect the inboard joint boot from the inboard joint 4.REMOVE INBOARD JOINT *a Matchmark a Remove any old grease from the inboard joint b Put matchmarks on the inboard joint and front drive outboard joint assembly NOTICE: Do not use a punch to make the matchmarks c Remove the inboard joint from the front drive outboard joint assembly d Using a snap ring expander, remove the snap ring https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…manual/repair/contents/RM100000000M5SP.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'59 pm e *a Matchmark Put matchmarks on the front drive outboard joint assembly and tripod joint NOTICE: · · f Using a brass bar and hammer, remove the tripod joint from the front drive outboard joint assembly NOTICE: · · g Do not use a punch to make the matchmarks Only put a matchmark on the front side of the tripod joint, so as not to confuse the installation direction Do not tap the rollers Do not drop the tripod joint Remove the front No axle inboard joint boot clamp LH, inboard joint boot and front axle inboard joint boot clamp LH 5.DISCONNECT FRONT NO AXLE OUTBOARD JOINT BOOT CLAMP LH 43447F a Using pliers, grasp and move the front No axle outboard joint boot clamp LH as shown in the illustration to disconnect it from the outboard joint boot 6.DISCONNECT FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH 43447E HINT: Use the same procedure described for the front No axle outboard joint boot clamp LH 7.REMOVE OUTBOARD JOINT BOOT https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M5SP.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 7'59 pm a Remove the front axle outboard joint boot clamp LH, outboard joint boot and front No axle outboard joint boot clamp LH from the front drive outboard joint assembly b Remove any old grease from the front drive outboard joint assembly 8.REMOVE FRONT DRIVE SHAFT DUST COVER LH a Using SST and a press, remove the front drive shaft dust cover LH from the front drive inboard joint assembly SST 09950-00020 9.REMOVE FRONT AXLE HUB DUST SEAL a 41336E 43502K Using a screwdriver and hammer, remove the front axle hub dust seal from the front drive outboard joint assembly © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M5SP.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 8(00 pm Print Exit DRIVE SHAFT / PROPELLER SHAFT FRONT DRIVE SHAFT ASSEMBLY INSPECTION CAUTION / NOTICE / HINT NOTICE: · · When using a vise, place aluminum plates between the part and vise When using a vise, not overtighten it PROCEDURE 1.INSPECT FRONT DRIVE SHAFT ASSEMBLY a Check that there is no excessive play in the radial direction of the inboard joint and outboard joint b Check that the inboard joint slides smoothly in the thrust direction c Check that there is no excessive play in the radial direction of the inboard joint d Check that the inboard joint boot and outboard joint boot are not cracked or damaged, and no grease is leaking out e Check that the inboard joint boot and outboard joint boot are not stretched or contracted when the front drive shaft assembly is at the standard length Length (A): Item Length for LH Side 555.9 mm (1.82 ft.) https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M5SM.html?PUB_TYPE=RM&MODE=1 Page of