Tài liệu hướng dẩn sửa chữa Hệ thống kiểm soát khí thải trên xe Hilux 2015 2018 manual 1gd ftv emission control he thong kiem soat khi thai . Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác, hiệu quả
Print-Toyota Service Information 11/3/17, 6(20 pm Print Exit 1GD-FTV EMISSION CONTROL DIFFERENTIAL PRESSURE SENSOR COMPONENTS ILLUSTRATION *1 DIFFERENTIAL PRESSURE SENSOR *3 AIR HOSE *2 - NO ENGINE COVER SUB-ASSEMBLY - N*m (kgf*cm, ft.*lbf): Specified torque - - © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000MMTX.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 6(21 pm Print Exit 1GD-FTV EMISSION CONTROL DIFFERENTIAL PRESSURE SENSOR INSTALLATION PROCEDURE 1.INSTALL DIFFERENTIAL PRESSURE SENSOR 89481B a *a Paint Mark Install the air hoses to the differential pressure sensor, and slide the clamps to secure the hoses HINT: Make sure the paint mark of the air hose side the differential pressure sensor b Connect the air hoses to the No vacuum pipe and No vacuum pipe, and slide the clamps to secure the hoses c Install the differential pressure sensor to the pipe clamp with the bolt Torque: 10 N*m (102 kgf*cm, ft.*lbf) d Connect the connector to the differential pressure sensor 2.INSTALL NO ENGINE COVER SUB-ASSEMBLY 12601B Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>INSTALLATION © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000MMTZ.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 6(20 pm Print Exit 1GD-FTV EMISSION CONTROL DIFFERENTIAL PRESSURE SENSOR ON-VEHICLE INSPECTION PROCEDURE 1.INSPECT DIFFERENTIAL PRESSURE SENSOR a Connect the GTS to the DLC3 b Remove the No engine cover sub-assembly c Slide the clamp and disconnect the air hose from the differential pressure sensor 89481B d Install SST to the differential pressure sensor SST 09992-00242 e Turn the ignition switch to ON f Turn the GTS on g Enter the following menus: Powertrain / Engine / Data List / DPF Differential Pressure https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000MMU0.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 6(20 pm h *a Pressure Apply pressure to the differential pressure sensor assembly i Check the pressure value of the differential pressure sensor Standard pressure: Approximately the same pressure as the applied pressure is indicated on the GTS NOTICE: Perform the inspection within the range of to 98 kPa (0 to 1.0 kgf/cm2, to 14.2 psi) If the result is not as specified, check the differential pressure sensor circuit j Remove SST from the differential pressure sensor k Connect the air hose to the differential pressure sensor, and slide the clamp to secure the hose l Install the No engine cover sub-assembly © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000MMU0.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 6(21 pm Print Exit 1GD-FTV EMISSION CONTROL DIFFERENTIAL PRESSURE SENSOR REMOVAL CAUTION / NOTICE / HINT CAUTION: To prevent burns, not touch the engine, exhaust manifold or other high temperature components while the engine is hot PROCEDURE 1.REMOVE NO ENGINE COVER SUB-ASSEMBLY 12601B Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL 2.REMOVE DIFFERENTIAL PRESSURE SENSOR 89481B CAUTION: To prevent burns, not touch the engine, exhaust manifold or other high temperature components while the engine is hot a Disconnect the connector from the differential pressure sensor b Remove the bolt and differential pressure sensor from the pipe clamp https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000MMTY.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 6(21 pm c Slide the clamps and disconnect the air hoses from the No vacuum pipe and No vacuum pipe d Slide the clamps and remove the No air hoses from the differential pressure sensor © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000MMTY.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 6(17 pm Print Exit 1GD-FTV EMISSION CONTROL EGR BYPASS VALVE SWITCHING VALVE COMPONENTS ILLUSTRATION *1 NO ENGINE COVER SUB-ASSEMBLY *3 ENGINE WIRE BRACKET *2 - VACUUM CONTROL VALVE SET - N*m (kgf*cm, ft.*lbf): Specified torque - - ILLUSTRATION https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000MMTG.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information *1 NO VACUUM SWITCHING VALVE ASSEMBLY N*m (kgf*cm, ft.*lbf): Specified torque 11/3/17, 6(17 pm *2 - BRACKET - © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000MMTG.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 6(17 pm Print Exit 1GD-FTV EMISSION CONTROL EGR BYPASS VALVE SWITCHING VALVE INSPECTION PROCEDURE 1.INSPECT NO VACUUM SWITCHING VALVE ASSEMBLY 25860 a *a Component without harness connected (No vacuum switching valve assembly) Measure the resistance according to the value(s) in the table below Standard Resistance: Tester Specified Condition Connection Condition 1-2 20°C (68°F) 33 to 39 Ω - Body ground - Body ground 20°C (68°F) MΩ or higher If the result is not as specified, replace the No vacuum switching valve assembly b Check operation of the No vacuum switching valve assembly https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…manual/repair/contents/RM100000000MMTJ.html?PUB_TYPE=RM&MODE=1 Page of Print-Toyota Service Information 11/3/17, 6(17 pm i *a *b Vacuum Air *c Port E *d Port F *e Filter When a vacuum of 60 kPa (450 mmHg, 18 in.Hg) is applied to port F, check that air flows from port E to the filter ii *a Air *b *c Port F Port E Apply battery voltage 12V across terminals and iii Check that air flows from port E to port F If the result is not as specified, replace the No vacuum switching valve assembly © 2012 TOYOTA MOTOR CORPORATION All Rights Reserved https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000MMTJ.html?PUB_TYPE=RM&MODE=1 Page of