Toyota land cruiser 1998 2007 service specifications các thông số kỹ thuật trên xe land cruiser đời 1998 2007

CÁC THÔNG SỐ KỸ THUẬT CỦA XE LAND CRUISER ĐỜI 1998-2007

Idle s eed Magnetic clutch not engaged

Magnetic clutch engaged 780 ± 50 rpmMagnetic clutch clearance 0.5 ± 0.15 mm (0.020 ± 0.0059 in.)

N → R position

Less than 1.2 secondsLess than 1.5 secondsEngine idle speed

Torque converter clutch installation distance

0.20 mm (0.0079 in.)0.30 mm (0.0118 in.)More than 17.1 mm (0.673 in.)Shift schedule

No.2 vehicle speed sensor x Transmission case NT

SP2

5.45.4

5555

48 in.·lbf

48 in.·lbfATF temperature sensor (for linear control ) x Valve body 11 112 8

ATF temperature sensor (for oil temp warning lamp ) x Valve body 10 100 7

Nut

133.9

13040

9

35 in.·lbfTransmission control shaft lever x Transmission control rod 13 130 9

Transfer shift lever x Transfer shift lever rod assembly 12 122 9

Nut

5074

510750

3754

Bolt B

7137

724377

5227

2nd

49Turn 90°

500Turn 90°

36Turn 90°

TURN SIGNAL FLASHER

FUEL SENDER GAUGE

DEFOGGER SWITCH (w/ Navigation)

-SERVICE SPECIFICATIONS BODY ELECTRICAL

SS-47

DEFOGGER SWITCH (w/o Navigation)

SLIDING ROOF CONTROL ASSEMBLY

POWER MIRROR SWITCH

4 - Ground (Ignition switch ACC or ON) Battery positive voltage

POWER SEAT SWITCH (Driver’s Seat)

POWER SEAT SWITCH (Passenger’s Seat)

LUMBAR SUPPORT SWITCH (Driver’s Seat)

POWER MIRROR SWITCH (Wire harness side)

4 - Ground (Ignition switch is ACC or ON) Battery positive voltage

POWER AMPLIFIER

REAR SEAT AUDIO

24 - Ground (Ignition switch ACC or ON) Battery positive voltage

DVD CHANGER

1 - Ground (Ignition switch ACC or ON) Battery positive voltage

RADIO RECEIVER

A11 - Ground (Ignition switch ACC or ON) Battery positive voltage

ANTENNA MOTOR CONTROL RELAY

17 - Ground (Ignition switch ACC or ON) Battery positive voltage

OVERHEAD J/B

2004 LAND CRUISER (RM1071U)

Rear bumper step reinforcement x Extension mounting bracket 12.5 127 11

2004 LAND CRUISER (RM1071U)

Front passenger airbag assembly x Instrument panel 6.0 61 53 in.·lbf

Seat position sensor x Seat adjuster Driver’s side: 8.0 82 71in.·lbf

-SERVICE SPECIFICATIONS BODY

SS-51

Seat belt reclining detecting part x Seat back assembly 3.9 40 35 in.·lbf

Brake pedal height (from asphalt sheet) 183.7 - 193.7 mm (7.232 - 7.626 in.)

Brake pedal reserve distance at 490 N (50 kgf, 110.1 lbf) More than 116 mm (4.57 in.)

Front brake pad thickness STD 11.5 mm (0.453 in.)

Front brake pad thickness Minimum 1.0 mm (0.039 in.)

Front brake disc thickness STD 32.0 mm (1.260 in.)

Front brake disc thickness Minimum 30.0 mm (1.181 in.)

Front brake disc runout Maximum 0.07 mm (0.0028 in.)

Rear brake pad thickness STD 12.0 mm (0.472 in.)

Rear brake pad thickness Minimum 1.0 mm (0.039 in.)

Rear brake disc thickness STD 18.0 mm (0.709 in.)

Rear brake disc thickness Minimum 16.0 mm (0.611 in.)

Rear brake disc runout Maximum 0.1 mm (0.004 in.)

Rear brake disc inside diameter STD 230 mm (9.06 in.)

Rear brake disc inside diameter Maximum 231 mm (9.09 in.)

Parking brake shoe lining thickness STD 4.0 mm (0.157 in.)

Parking brake shoe lining thickness Minimum 1.0 mm (0.039 in.)

Parking brake lever travel at 196 N (20 kgf, 44 lbf) 4 - 6 clicks

Parking brake clearance between rear shoe and lever Less than 0.25 mm (0.0098 in.)

Parking brake shoe and lever clearance adjusting shim thickness

0.3 mm (0.012 in.)0.4 mm (0.016 in.)0.5 mm (0.020 in.)0.6 mm (0.024 in.)0.9 mm (0.035 in.)

ABS ECU or ABS & BA & TRAC & VSC ECU set nut 5.0 51 44 in.·lbf

Master cylinder pressure sensor (w/ ABS & BA & TRAC & VSC only) 81 830 60

Rotor coil resistance at 20°C (68°F)

Minimum

Minimum

12V 130A2.3 - 2.7 Ω

14.2 - 14.4 mm (0.559 - 0.567 in.)14.0 mm (0.551 in.)

10.5 mm (0.413 in.)4.5 mm (0.177 in.)Charging circuit Without load STD amperage

STD voltage

10 A or less13.2 - 14.8 V

30 A or less

Nut 10 mmNut 8 mm

393915.5

400440158

292911

93 - 123 kPa (0.95 - 1.25 kgf/cm2, 13.5 - 17.8 psi)

78 kPa (0.8 kgf/cm2, 11.4 psi)

Stud bolt and nut

2118

215185

1513

1,324 kPa (13.5 kgf/cm2, 192 psi) or more

No.02No.04No.06No.08No.10No.12No.14No.16No.18No.20No.22No.24No.26No.28No.30No.32No.34No.36No.38No.40No.42No.44No.46No.48No.50No.52No.54No.56No58No.60No.62No.64No.66No.68No.70No.72No.74No.76No.78No.80

0.15 - 0.25 mm (0.006 - 0.010 in.)0.25 - 0.35 mm (0.010 - 0.014 in.)2.000 mm (0.0787 in.)

2.020 mm (0.0795 in.)2.040 mm (0.0803 in.)2.060 mm (0.0811 in.)2.080 mm (0.0819 in.)2.100 mm (0.0827 in.)2.120 mm (0.0835 in.)2.140 mm (0.0843 in.)2.160 mm (0.0850 in.)2.180 mm (0.0858 in.)2.200 mm (0.0866 in.)2.220 mm (0.0874 in.)2.240 mm (0.0882 in.)2.260 mm (0.0890 in.)2.280 mm (0.0898 in.)2.300 mm (0.0906 in.)2.320 mm (0.0913 in.)2.340 mm (0.0921 in.)2.360 mm (0.0929 in.)2.380 mm (0.0937 in.)2.400 mm (0.0945 in.)2.420 mm (0.0953 in.)2.440 mm (0.0961 in.)2.460 mm (0.0969 in.)2.480 mm (0.0976 in.)2.500 mm (0.0984 in.)2.520 mm (0.0992 in.)2.540 mm (0.1000 in)2.560 mm (0.1008 in.)2.580 mm (0.1016 in.)2.600 mm (0.1024 in.)2.620 mm (0.1031 in.)2.640 mm (0.1039 in.)2.660 mm (0.1047 in.)2.680 mm (0.1055 in.)2.700 mm (0.1063 in.) 2.720 mm (0.1071 in.)2.740 mm (0.1079 in.)2.760 mm (0.1087 in.)2.780 mm (0.1094 in.)2.800 mm (0.1102 in.)Ignition timing w/ Terminals TC and E1 connected of DLC1 5 -15° BTDC @ idle

2004 LAND CRUISER (RM1071U)

Valve seat Refacing angle Contacting angle Contacting widthValve guide bushing bore diameter STD

O/S 0.05Cylinder head bolt thread inside diameter STD

9.2 - 9.8 mm (0.362 - 0.386 in.)8.2 - 8.8 mm (0.323 - 0.346 in.)Valve guide

bushing

Inside diameterOutside diameter (for repair part) STD

O/S 0.05

5.510 - 5.530 mm (0.2169 - 0.2177 in.)10.285 - 10.306 mm (0.4049 - 0.4057 in.)10.335 - 10.356 mm (0.4069 - 0.4077 in.)

ExhaustMinimum IntakeExhaustValve face angle

ExhaustStem oil clearance STD Intake

ExhaustMaximum IntakeExhaustMargin thickness STD IN

EXMinimum

95.05 mm (3.7421 in.)95.10 mm (3.7441 in.)94.55 mm (3.7224 in.)94.60 mm (3.7244 in.)44.5°

5.470 - 5.485 mm (0.2154 - 0.2159 in.)5.465 - 5.480 mm (0.2152 - 0.2157 in.)0.025 - 0.060 mm (0.0010 - 0.0024 in.)0.030 - 0.065 mm (0.0012 - 0.0026 in.)0.08 mm (0.0031 in.)

0.10 mm (0.0039 in.)1.25 mm (0.049 in.)1.4 mm (0.055 in.)0.5 mm (0.020 in.)

Free lengthInstalled tension at 35.0 mm (1.378 in.)

2.0 mm (0.079 in.)54.1 mm (2.130 in.)

204 - 226 N (20.8 - 23.0 kgf·cm, 45.9 - 50.7 lbf)Valve lifter Lifter diameter

Lifter bore diameter

Maximum

30.966 - 30.976 mm (1.2191 - 2.2195 in.)31.000 - 31.016 mm (1.2205 - 1.2211 in.)0.024 - 0.050 mm (0.0009 - 0.0020 in.)0.07 mm (0.0028 in.)

ExhaustMaximum

MaximumJournal diameter

Circle runout

ExhaustMinimum IntakeExhaust

MaximumCamshaft gear spring end free distance

0.040 - 0.090 mm (0.0016 - 0.0035 in.)0.040 - 0.085 mm (0.0016 - 0.0033 in.)0.12 mm (0.0047 in.)

0.030 - 0.067 mm (0.0012 - 0.0026 in.)0.10 mm (0.0039 in.)

26.954 - 26.970 mm (1.0612 - 1.0618 in.)0.08 mm (0.0031 in.)

41.94 - 42.04 mm (1.6512 - 1.6551 in.)41.96 - 42.06 mm (1.6520 - 1.6559 in.)41.79 mm (1.6453 in.)

41.81 mm (1/6461 in.)0.020 - 0.200 mm (0.0008 - 0.0079 in.)0.30 mm (0.0188 in.)

18.2 - 18.8 mm (0.712 - 0.740 in.)

Exhaust

0.15 mm (0.0059 in.)0.50 mm (0.0197 in.)

0.07 mm (0.0028 in.)94.002 - 94.010 mm (3.7009 - 3.7012 in.)94.010 - 94.023 mm (3.7012 - 3.7017 in.)94.023 - 94.031 mm (3.7017 - 3.7020 in.)94.231 mm (3.7099 in.)

94.731 mm (3.7296 in.)10.760 - 10.970 mm (0.4236 - 0.4319 in.)10.40 mm (0.4094 in.)

Piston and

piston ring

Mark 2Mark 3O/S 0.50

MaximumPiston ring groove clearance No.1

No.2Piston ring end gap STD No.1

No.2OilMaximum No.1

No.2Oil

93.902 - 93.912 mm (3.6969 - 3.6973 in.)93.912 - 93.920 mm (3.6973 - 3.6976 in.)93.920 - 93.930 mm (3.6976 - 3.6980 in.)94.402 - 94.430 mm (3.7166 - 3.7177 in.)0.090 - 0.111 mm (0.0035 - 0.0044 in.)0.13 mm (0.0051 in.)

0.030 - 0.080 mm (0.0012 - 0.0031 in.)0.030 - 0.070 mm (0.0012 - 0.0028 in.)0.300 - 0.500 mm (0.0118 - 0.0197 in.)0.400 - 0.650 mm (0.0157 - 0.0256 in.)0.130 - 0.480 mm (0.0051 - 0.0189 in.)1.10 mm (0.0433 in.)

1.20 mm (0.0472 in.)1.15 mm (0.0453 in.)

MaximumConnecting rod thickness

Connecting rod oil clearance STD

MaximumConnecting rod bearing center wall thickness

Mark 3Mark 4Mark 5Mark 6Mark 7Rod bend Maximum per 100 mm (3.94 in.)Rod twist Maximum per 100 mm (3.94 in.)Bushing inside diameter

Piston pin diameter

MaximumConnecting rod bolt tension portion diameter STD

Minimum

0.160 - 0.290 mm (0.0063 - 0.0138 in.)0.35 mm (0.0138 in.)

22.880 - 22.920 mm (0.9008 - 0.9024 in.)0.027 - 0.053 mm (0.0011 - 0.0021 in.)0.065 mm (0.0026 in.)

1.484 - 1.487 mm (0.0584 - 0.0585 in.)1.487 - 1.490 mm (0.0585 - 0.0587 in.)1.490 - 1.493 mm (0.0587 - 0.0588 in.)1.493 - 1.496 mm (0.0588 - 0.0589 in.)1.496 - 1.499 mm (0.0589 - 0.0590 in.)1.499 - 1.502 mm (0.0590 - 0.0591 in.)0.05 mm (0.0020 in.)

0.15 mm (0.0059 in.)22.005 - 22.014 mm (0.8663 - 0.8667 in.)21.997 - 22.006 mm (0.8660 - 0.8664 in.)0.005 - 0.011 mm (0.0002 - 0.0004 in)0.05 mm (0.0020 in.)

7.200 - 7.300 mm (0.2835 - 0.2874 in.)7.00 mm (0.2756 in.)

MaximumThrust washer thickness

Main journal bore diameter on cylinder block (with main bearing)

Main journal oil clearance STD

MaximumMain journal diameter

0.020 - 0.220 mm (0.0008 - 0.0087 in.)0.30 mm (0.0118 in.)

2.440 - 2.490 mm (0.0961 - 0.0980 in.)66.986 - 67.000 mm (2.6372 - 2.6378 in.)0.040 - 0.058 mm (0.0016 - 0.0023 in.)0.070 mm (0.0028 in.)

66.988 - 67.000 mm (2.6373 - 2.6378 in.)

Main bearing center wall thickness (Reference)

No.1 and No.5 Mark 3

Mark 4Mark 5Mark 6Mark 7Others Mark 1Mark 2Mark 3Mark 4Mark 5Crank pin diameter

Main journal taper and out-of-round MaximumCrank pin taper and out-of-round Maximum

2.481 - 2.484 mm (0.0977 - 0.0978 in.)2.484 - 2.487 mm (0.0978 - 0.0979 in.)2.487 - 2.490 mm (0.0979 - 0.0980 in.)2.490 - 2.493 mm (0.0980 - 0.0981 in.)2.493 - 2.496 mm (0.0981 - 0.0983 in.)2.481 - 2.484 mm (0.0977 - 0.0978 in.)2.484 - 2.487 mm (0.0978 - 0.0979 in.)2.487 - 2.490 mm (0.0979 - 0.0980 in.)2.490 - 2.493 mm (0.0980 - 0.0981 in.)2.493 - 2.496 mm (0.0981 - 0.0983 in.)51.982 - 52.000 mm (2.0465 - 2.0472 in.)0.08 mm (0.0031 in.)

0.02 mm (0.0008 in.)0.02 mm (0.0008 in.)

Radiator bracket x Radiator assembly Bolt

Nut

1820

185200

1315

Fan bracket x Cylinder block 12 mm head

14 mm head

1632

160330

1224

No.3 timing belt cover x Cylinder block, cylinder head 7.5 80 66 in.·lbf

2nd3rd

32Turn 90°

Turn 90°

325Turn 90°

Turn 90°

24Turn 90°

Turn 90°

Camshaft bearing cap x Cylinder head Bolt C

Others

7.516

80160

66 in.·lbf12

Front water bypass joint, Rear water bypass joint x Cylinder head 18 185 13

2nd

49Turn 90°

500Turn 90°

36Turn 90°

2nd

27Turn 90°

275Turn 90°

20Turn 90°

2004 LAND CRUISER (RM1071U)

Heated oxygen sensor (Bank 1, 2 sensor 2) x Front exhaust pipe 20 200 14

Maximum electrode gap for used spark plug

SK20R11IFR6A111.1 mm (0.043 in.)1.3 mm (0.051 in.)Camshaft

2,065 - 3,225 Ω

Ignition coil (with igniter) x Cylinder head cover 7.5 80 66 in.·lbf

0.030 - 0.090 mm (0.0012 - 0.0035 in.)0.15 mm (0.0059 in.)

0.100 - 0.175 mm (0.0039 - 0.0069 in.)0.30 mm (0.0118 in.)

12 mm and 6mm hexagon head

30.515.5

310160

2211

No.1 oil pan x Cylinder block 10 mm head

12 mm head

7.528

80290

66 in.·lbf21

Shaft runout

Bearing axial play

Snap ring thickness

0.8 mm (0.031 in.)

0 mm (0 in.)

2.44 - 2.46 mm (0.0961 - 0.0969 in.) 2.46 - 2.48 mm (0.0969 - 0.0976 in.)

Max.

Max.

Color Mark

Brown Blue

2.30 - 2.32 mm (0.0906 - 0.0913 in.) 2.34 - 2.36 mm (0.0921 - 0.0929 in.)

2.28 - 2.30 mm (0.0898 - 0.0906 in.) 2.32 - 2.34 mm (0.0913 - 0.0921 in.) 2.36 - 2.38 mm (0.0929 - 0.0937 in.) 2.38 - 2.40 mm (0.0937 - 0.0945 in.) 2.40 - 2.42 mm (0.0945 - 0.0953 in.) 2.42 - 2.44 mm (0.0953 - 0.0961 in.)

Front passenger airbag assembly x Instrument panel 6.0 61 53 in.·lbfFront passenger airbag assembly x Instrument panel reinforcement 20 205 15

Front seat outer belt x Body Upper bolt:

Lower bolt:

8.042

81428

71 in.·lbf31

Seat position sensor assembly x Seat adjuster assembly 8.0 82 71 in.·lbf

2004 LAND CRUISER (RM1071U)

SUSPENSION AND AXLE

71 mm (2.795 in.)

51 mm (2.008 in.)Camber

Right-left error

0°05’ ± 45’ (0.08°± 0.75°)30’ (0.5°) or less

F t h l

Caster

Right-left error

2°30’ ± 45’ (2.5°± 0.75°)30’ (0.5°) or less

Front wheel

alignment Steering axis inclination

Right-left error

12°10’ ± 45’ (12.17°± 0.75°)30’ (0.5°) or less

Toe-in (total)

Rack end length difference

0°06’ ± 12’ (0.1°± 0.2°, 1 ± 2 mm, 0.04 ± 0.08 in.)3.0 mm (0.118 in.) or less

Outside wheel: Reference

36°42’ (33°42’ - 36°42’)36.7° (33.7° - 36.7°)

A: Ground clearance of spindle center

B: Ground clearance of lower suspension arm front bolt center

C: Ground clearance of rear axle shaft center

D: Ground clearance of lower control arm front bushing center

Reused bearing

1.0 - 1.6 N·m (10 - 16 kgf·cm, 8.9 - 14.2 in.·lbf)0.5 - 0.8 N·m (5 - 8 kgf·cm, 4.4 - 7.1 in.·lbf)Total preload (at starting) Drive pinion preload plus

0.4 - 0.6 N·m (4 - 6 kgf·cm, 3.5 - 5.3 in.·lbf)Ring gear runout Max 0.07 mm (0.0028 in.)

Front differential Ring gear backlash 0.13 - 0.18 mm (0.0051 - 0.0071 in.)

Front differential

Side gear backlash 0.05 - 0.20 mm (0.0020 - 0.0079 in.)Differential case runout Max 0.07 mm (0.0028 in.)

Front differential oil seal drive in depth 1.5 mm (0.059 in.)

Side gear thrust washer thickness

0.9 mm (0.035 in.)1.0 mm (0.039 in.)1.1 mm (0.043 in.)1.2 mm (0.047 in.)1.3 mm (0.051 in.)

2004 LAND CRUISER (RM1071U)

Front differential Side bearing adjusting washer thickness

2.58 mm (0.1016 in.)2.60 mm (0.1024 in.)2.62 mm (0.1031 in.)2.64 mm (0.1039 in.)2.66 mm (0.1047 in.)2.68 mm (0.1055 in.)2.70 mm (0.1063 in.)2.72 mm (0.1071 in.)2.74 mm (0.1079 in.)2.76 mm (0.1087 in.)2.78 mm (0.1094 in.)2.80 mm (0.1102 in.)2.82 mm (0.1110 in.)2.84 mm (0.1118 in.)2.86 mm (0.1126 in.)2.88 mm (0.1134 in.)2.90 mm (0.1142 in.)2.92 mm (0.1150 in.)2.94 mm (0.1157 in.)2.96 mm (0.1165 in.)2.98 mm (0.1173 in.)3.00 mm (0.1181 in.)3.02 mm (0.1189 in.)3.04 mm (0.1197 in.)3.06 mm (0.1205 in.)3.08 mm (0.1213 in.)3.10 mm (0.1220 in.)3.12 mm (0.1228 in.)3.14 mm (0.1236 in.)3.16 mm (0.1244 in.)3.18 mm (0.1252 in.)3.20 mm (0.1260 in.)3.22 mm (0.1268 in.)3.24 mm (0.1276 in.)3.26 mm (0.1283 in.)3.28 mm (0.1291 in.)3.30 mm (0.1299 in.)3.32 mm (0.1307 in.)3.34 mm (0.1315 in.)3.36 mm (0.1323 in.)3.38 mm (0.1331 in.)3.40 mm (0.1339 in.)3.42 mm (0.1346 in.)3.44 mm (0.1354 in.)3.46 mm (0.1362 in.)3.48 mm (0.1370 in.)

2004 LAND CRUISER (RM1071U)

Companion flange vertical runout Max 0.10 mm (0.0039 in.)Companion flange lateral runout Max 0.10 mm (0.0039 in.)Drive pinion preload (at starting) New bearing

Reused bearing

1.3 - 1.8 N·m (13 - 19 kgf·cm, 11.5 - 15.9 in.·lbf)0.64 - 0.92 N·m (6.5 - 9.4 kgf·cm, 5.7 - 8.1 in.·lbf)Total preload (at starting) Drive pinion preload plus

0.38 - 0.63 N·m (3.9 - 6.5 kgf·cm, 3.3 - 5.6 in.·lbf)Ring gear runout Max 0.05 mm (0.0020 in.)

Ring gear backlash 0.13 - 0.18 mm (0.0051 - 0.0071 in.)Side gear backlash 0.02 - 0.15 mm (0.0008 - 0.0059 in.)Differential case runout Max 0.04 mm (0.0016 in.)

Rear differential front oil seal drive in depth 0.5 mm (0.020 in.)

Rear differential

Side gear thrust washer thickness

1.55 mm (0.061 in.)1.60 mm (0.063 in.)1.65 mm (0.065 in.)1.70 mm (0.067 in.)1.75 mm (0.069 in.)1.80 mm (0.071 in.)1.85 mm (0.073 in.)1.90 mm (0.075 in.)1.95 mm (0.077 in.)2.00 mm (0.079 in.)2.05 mm (0.081 in.)2.10 mm (0.083 in.)

Tooth contact pattern adjusting washer thickness

1.050 mm (0.04134 in.)1.075 mm (0.04232 in.)1.100 mm (0.04331 in.)1.125 mm (0.04429 in.)1.150 mm (0.04528 in.)1.175 mm (0.04626 in.)1.200 mm (0.04724 in.)1.225 mm (0.04823 in.)1.250 mm (0.04921 in.)1.275 mm (0.05020 in.)1.300 mm (0.05118 in.)1.325 mm (0.05217 in.)1.350 mm (0.05315 in.)1.375 mm (0.05413 in.)1.400 mm (0.05512 in.)1.425 mm (0.05610 in.)1.450 mm (0.05709 in.)1.475 mm (0.05807 in.)1.500 mm (0.05906 in.)1.525 mm (0.06004 in.)1.550 mm (0.06102 in.)