1. Trang chủ
  2. » Kỹ Thuật - Công Nghệ

Toyota land cruiser 1998 2007 lubrication hệ thống bôi trơn trên xe land cruiser đời 1998 2007

22 709 0

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 22
Dung lượng 555 KB

Nội dung

HỆ THỐNG BÔI TRƠN TRÊN XE LAND CRUISER ĐỜI 1998-2007

B16233 Recommended Viscosity (SAE): TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE 5W-30 °C °F -20 -29 0 -18 20 -7 40 4 60 16 80 27 100 38 LU08N-04 B04468 Front B04469 Oil Pressure Gauge Oil Pressure Switch P08343 Adhesive -LUBRICATION OIL AND FILTER LU-1 1782Author: Date: 2004 LAND CRUISER (RM1071U) OIL AND FILTER INSPECTION 1. CHECK ENGINE OIL QUALITY Check the oil for deterioration, entry of water, discoloring or thin- ning. If the quality is visibly poor, replace the oil. Oil grade: API grade SL Energy-Conserving or ILSAC multi- grade engine oil. 2. CHECK ENGINE OIL LEVEL The oil level should be between the ”L” and ”F” marks on the dip- stick. If low, check for leakage and add oil up to the ”F” mark. NOTICE: L Do not fill with engine oil above the ”F” mark. L Install the oil dipstick facing the direction shown in the illustration. 3. REMOVE ENGINE UNDER COVER NO.1 4. REMOVE OIL PRESSURE SWITCH 5. INSTALL OIL PRESSURE GAUGE 6. WARM UP ENGINE Allow the engine to warm up to normal operating temperature. 7. CHECK OIL PRESSURE Oil pressure: At idle: 29 kPa (0.3 kgf/cm 2 , 4.2 psi) or more At 3,000 rpm: 294 - 588 kPa (3.0 - 6.0 kgf/cm 2, 43 - 85 psi) 8. REMOVE OIL PRESSURE GAUGE 9. REINSTALL OIL PRESSURE SWITCH (a) Apply adhesive to 2 or 3 threads of the oil pressure switch. Adhesive: Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent (b) Reinstall the oil pressure switch. 10. START ENGINE, AND CHECK FOR ENGINE OIL LEAKS 11. REINSTALL ENGINE UNDER COVER NO.1 LU08O-02 B04490 Engine Under Cover No.3 B04609 B04481 Service Hole Cover LU-2 -LUBRICATION OIL AND FILTER 1783Author: Date: 2004 LAND CRUISER (RM1071U) REPLACEMENT CAUTION: L Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addi- tion, used engine oil contains potentially harmful contaminants which may cause skin cancer. L Care should be taken, therefore, when changing en- gine oil to minimize the frequency and length of time your skin is exposed to used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be thoroughly washed with soap and water, or use water-less hand cleaner, to remove any used engine oil. Do not use gasoline, thinners, or solvents. L In order to preserve the environment, used oil and used oil filters must be disposed of only at desig- nated disposal sites. 1. DRAIN ENGINE OIL (a) Remove the 2 nuts and engine under cover No.3. (b) Remove the oil filler cap. (c) Remove the oil drain plug, and drain the oil into a contain- er. 2. REPLACE OIL FILTER (a) Remove the 2 bolts and service hole cover. B04482 SST B04483 B04484 SST 3/4 Turn -LUBRICATION OIL AND FILTER LU-3 1784Author: Date: 2004 LAND CRUISER (RM1071U) (b) Using SST, remove the oil filter. SST 09228-07501 (c) Clean the oil filter contact surface on the oil filter mount- ing. (d) Lubricate the filter rubber gasket with clean engine oil. (e) Tighten the oil filter by hand until the rubber gasket con- tacts the seat of the filter mounting. (f) Using SST, give it an additional 3/4 turn to seat the filter. SST 09228-07501 3. REFILL WITH ENGINE OIL (a) Clean and install the oil drain plug with a new gasket. Torque: 39 N·m (400 kgf·cm, 29 ft·lbf) (b) Fill with new engine oil. Capacity: Drain and refill: w/ Oil filter change: 6.8 liters (7.2 US qts, 6.0 Imp. qts) w/o Oil filter change: 6.4 liters (6.8 US qts, 5.6 Imp. qts) Dry fill: 8.0 liters (8.5 US qts, 7.0 Imp. qts) (c) Reinstall the oil filler cap. 4. START ENGINE AND CHECK FOR ENGINE OIL LEAKS 5. RECHECK ENGINE OIL LEVEL 6. REINSTALL ENGINE UNDER COVER NO.3 AND SER- VICE HOLE COVER LU08W-08 B04473 Oil Cooler Hose L O-Ring Oil Cooler Plate Washer Union Bolt Oil Filter N·m (kgf·cm, ft·lbf) : Specified torque L Non-reusable part 68.6 (700, 51) -LUBRICATION OIL COOLER LU-19 1800Author: Date: 2004 LAND CRUISER (RM1071U) OIL COOLER COMPONENTS LU08Y-06 B04610 -LUBRICATION OIL COOLER LU-21 1802Author: Date: 2004 LAND CRUISER (RM1071U) INSPECTION INSPECT OIL COOLER Check the oil cooler for damage or clogging. If necessary, replace the oil cooler. LU08Z-08 B04611 New O-Ring B04612 LU-22 -LUBRICATION OIL COOLER 1803Author: Date: 2004 LAND CRUISER (RM1071U) INSTALLATION 1. INSTALL OIL COOLER (a) Clean the oil cooler contact surface on the cooler mount- ing. (b) Install a new O-ring to the oil cooler. (c) Apply a light coat of engine oil on the threads and under the head of the union bolt. (d) Install the plate washer and union bolt. Torque: 68.6 N·m (700 kgf·cm, 51 ft·lbf) (e) Connect the 2 oil cooler hoses to the oil cooler. 2. INSTALL OIL FILTER (See page LU-2 ) 3. FILL WITH ENGINE COOLANT 4. START ENGINE AND CHECK FOR ENGINE OIL LEAKS 5. CHECK ENGINE OIL LEVEL LU08X-06 B04612 LU-20 -LUBRICATION OIL COOLER 1801Author: Date: 2004 LAND CRUISER (RM1071U) REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE OIL FILTER (See page LU-2 ) 3. REMOVE OIL COOLER (a) Disconnect the 2 oil cooler hoses from the oil cooler. (b) Remove the union bolt, plate washer and the oil cooler. (c) Remove the O-ring from the oil cooler. LU08P-07 B04470 B04791 RH No.3 Timing Belt Cover LH No.3 Timing Belt Cover No.2 Timing Belt Cover Camshaft Position Sensor Connector Engine Wire Drive Belt Idler Pulley Timing Belt Fan Bracket N·m (kgf·cm, ft·lbf) : Specified torque Oil Cooler Pipe Timing Belt Tensioner Dust Boot Cover Plate 39 (400,29) 245 (2,500, 181) 32 (330, 24) 16 (160, 12) 7.5 (80, 66 in.·lbf) 16 (160, 12) Water Bypass Hose LU-4 -LUBRICATION OIL PUMP 1785Author: Date: 2004 LAND CRUISER (RM1071U) OIL PUMP COMPONENTS B04472 Generator Drive Belt Tensioner No.1 Timing Belt Cover Crankshaft Pulley Timing Belt Timing Belt Guide (Crankshaft Angle Sensor Plate) No.1 Idler Pulley Crankshaft Timing Pulley Plate Washer No.2 Idler Pulley Timing Belt Cover Spacer Gasket L Precoated part N·m (kgf·cm, ft·lbf) : Specified torque 39 (400, 29) 34.5 (350, 25) L 34.5 (350, 25) -LUBRICATION OIL PUMP LU-5 1786Author: Date: 2004 LAND CRUISER (RM1071U) B04485 Oil Pump Crankshaft Position Sensor Connector Crankshaft Position Sensor Oil Filter, Oil Cooler and Filter Bracket Assembly Oil Cooler Hose Clamp Oil Strainer Oil Dipstick Guide and Dipstick  O-Ring  Gasket No.1 Oil Pan No.2 Oil Pan Oil Pan Baffle Plate Clamp  Gasket Drain Plug x 20 N·m (kgf·cm, ft·lbf) : Specified torque  Non-reusable part  Gasket 30.5 (310, 22) 15.5 (160, 11)  O-Ring 15.5 (160, 11) x 4 x 8 28 (290, 21) 7.5 (80, 66 in.·lbf) 7.5 (80, 66 in.·lbf) 7.5 (80, 66 in.·lbf) 7.5 (80, 66 in.·lbf) 39 (400, 29) 7.5 (80, 66 in.·lbf) 18 (185,13) 15 (153,11) LU-6 -LUBRICATION OIL PUMP 1787Author: Date: 2004 LAND CRUISER (RM1071U) [...]... to damage the contact surface of the cylinder block and oil pump (c) Remove the O-ring from the cylinder block B00951 2004 LAND CRUISER (RM1071U) Author : Date : 1791 LU-13 LUBRICATION - OIL PUMP LU08T-02 REPLACEMENT REPLACE CRANKSHAFT FRONT OIL SEAL (See page EM-104 ) 2004 LAND CRUISER (RM1071U) Author : Date : 1794 ...LU-7 LUBRICATION - OIL PUMP Oil Pump Body Drive Rotor Driven Rotor x 10 Oil Pump Body Cover Relief Valve Crankshaft Front Oil Seal Compression Spring Retainer Snap Ring Non-reusable part B03735 2004 LAND CRUISER (RM1071U) Author : Date : 1788 LU-1 1 LUBRICATION - OIL PUMP LU08R-07 DISASSEMBLY 1 (a) (b) REMOVE RELIEF VALVE Using... 0.30 mm (0.0118 in.) If the body clearance is greater than maximum, replace the rotors as a set If necessary, replace the oil pump assembly 6 REMOVE DRIVE AND DRIVE ROTORS 2004 LAND CRUISER (RM1071U) Author : Date : 1793 LU-15 LUBRICATION - OIL PUMP LU08V-03 INSTALLATION 1 (a) A B A Seal Width 2 - 3 mm B B00960 INSTALL OIL PUMP Remove any old packing (FIPG) material and be careful not to drop any oil... ft·lbf) for 14 mm head Engage P21388 A A A E C D HINT: A B B00950 L L Use a 6 mm hexagon wrench for the hexagon head bolt Each bolt length is indicated in the illustration 2004 LAND CRUISER (RM1071U) Author : Date : 1796 LU-16 LUBRICATION - OIL PUMP Bolt length: 35 mm (1.38 in.) for A of 12 mm head 50 mm (1.97 in.) for B of 12 mm head 106 mm (4.17 in.) for C of 12 mm head 40 mm (1.57 in.) for D of 14... L Parts must be assembled within 5 minutes of application Otherwise the material must be removed and reapplied L Immediately remove nozzle from the tube and reinstall cap 2004 LAND CRUISER (RM1071U) Author : Date : 1797 LU-17 LUBRICATION A B B B B (c) C C A D A D A B B B B C C B04459 - OIL PUMP Temporarily install the No.1 oil pan with the 19 bolts, stud bolt and 2 nuts HINT: Each bolt length is indicated... No.2 oil pan as shown in the illustration Seal packing: Part No 08826-00080 or equivalent L Install a nozzle that has been cut to a 3 - 4 mm (0.12 - 0.16 in.) opening B04489 2004 LAND CRUISER (RM1071U) Author : Date : 1798 LU-18 LUBRICATION - OIL PUMP L (c) Parts must be assembled within 5 minutes of application Otherwise the material must be removed and reapplied L Immediately remove nozzle from the tube... EM-22 ) INSTALL NO.2 IDLER PULLEY (See page EM-22 ) INSTALL TIMING BELT (See page EM-22 ) DISCONNECT ENGINE FROM ENGINE STAND INSTALL ENGINE TO VEHICLE (See page EM-81 ) 2004 LAND CRUISER (RM1071U) Author : Date : 1799 LU-14 LUBRICATION - OIL PUMP LU08U-05 REASSEMBLY 1 (a) INSTALL DRIVE AND DRIVEN ROTORS Place the drive and driven rotors into pump body with the marks facing the pump body cover side... (a) Mark INSTALL RELIEF VALVE Insert the relief valve, spring and retainer into the oil pump body hole Using snap ring pliers, install the snap ring B04455 B03741 (b) B03740 2004 LAND CRUISER (RM1071U) Author : Date : 1795 LU-8 LUBRICATION - OIL PUMP LU08Q-08 REMOVAL HINT: When repairing the oil pump, the oil pan and strainer should be removed and cleaned 1 REMOVE ENGINE FROM VEHICLE (See page EM-77 )... the No.2 oil pan SST 09032-00100 NOTICE: L Be careful not to damage the No.2 oil pan contact surface of the No.1 oil pan L Be careful not to damage the No.2 oil pan flange 2004 LAND CRUISER (RM1071U) Author : Date : 1789 LU-9 LUBRICATION - OIL PUMP 11 REMOVE OIL PAN BAFFLE PLATE Remove the 4 bolts, 2 nuts and baffle plate B03737 12 (a) REMOVE NO.1 OIL PAN Remove the 18 bolts and 2 nuts B03738 (b) Using... careful not to damage the contact surface of the cylinder block and No.1 oil pan Ply B05144 13 REMOVE OIL STRAINER Remove the 2 bolt, 2 nuts, oil strainer and gasket B03739 2004 LAND CRUISER (RM1071U) Author : Date : 1790 LU-10 LUBRICATION - OIL PUMP 14 REMOVE OIL PUMP (a) Remove the 8 bolts HINT: Use a 6 mm hexagon wrench for the hexagon head bolt B01044 (b) Using a screwdriver, remove the oil pump by . Ring Retainer Oil Pump Body -LUBRICATION OIL PUMP LU-7 1788Author: Date: 2004 LAND CRUISER (RM1071U) LU08R-07 B03740 B03741 -LUBRICATION OIL PUMP LU-1 1 1792Author: Date: 2004 LAND CRUISER (RM1071U) DISASSEMBLY 1 51) -LUBRICATION OIL COOLER LU-19 1800Author: Date: 2004 LAND CRUISER (RM1071U) OIL COOLER COMPONENTS LU08Y-06 B04610 -LUBRICATION OIL COOLER LU-21 1802Author: Date: 2004 LAND CRUISER (RM1071U) INSPECTION INSPECT. OIL CHANGE 5W-30 °C °F -2 0 -2 9 0 -1 8 20 -7 40 4 60 16 80 27 100 38 LU08N-04 B04468 Front B04469 Oil Pressure Gauge Oil Pressure Switch P08343 Adhesive -LUBRICATION OIL AND FILTER LU-1 1782Author:

Ngày đăng: 24/05/2014, 15:30

TỪ KHÓA LIÊN QUAN

TÀI LIỆU CÙNG NGƯỜI DÙNG

TÀI LIỆU LIÊN QUAN

w