© ISO 2016 Tool holders with cylindrical shank — Part 7 Type F with taper seat Porte outil à queue cylindrique — Partie 7 Porte outil de type F pour outils à queue conique INTERNATIONAL STANDARD ISO 1[.]
INTERNATIONAL STANDARD ISO 10889-7 Third edition 2016-03-15 Tool holders with cylindrical shank — Part 7: Type F with taper seat Porte-outil queue cylindrique — Partie 7: Porte-outil de type F pour outils queue conique Reference number ISO 10889-7:2016(E) © ISO 2016 ISO 10889-7:2016(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2016, Published in Switzerland All rights reserved Unless otherwise specified, no part o f this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country o f the requester ISO copyright o ffice Ch de Blandonnet • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel +41 22 749 01 11 Fax +41 22 749 09 47 copyright@iso.org www.iso.org ii © ISO 2016 – All rights reserved ISO 10889-7:2016(E) Contents Page Foreword iv Scope Normative references Dimensions Designation Technical delivery conditions Annex A (informative) Relationship between designations in this part of ISO 10889 and ISO 13399 Bibliography © ISO 2016 – All rights reserved iii ISO 10889-7:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work o f preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o f electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part In particular the different approval criteria needed for the di fferent types o f ISO documents should be noted This document was dra fted in accordance with the editorial rules of the ISO/IEC Directives, Part (see www.iso.org/directives) Attention is drawn to the possibility that some o f the elements o f this document may be the subject o f patent rights ISO shall not be held responsible for identi fying any or all such patent rights Details o f any patent rights identified during the development o f the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents) Any trade name used in this document is in formation given for the convenience o f users and does not constitute an endorsement For an explanation on the meaning o f ISO specific terms and expressions related to formity assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary in formation The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, Holding tools, adaptive items and interfaces This third edition cancels and replaces the second edition (ISO 10889-7:2004), of which it constitutes a minor revision, notably with the addition o f Annex A, which gives the relationship between the designations of this part of ISO 10889 and the ISO 13399 series ISO 10889 consists of the following parts, under the general title Tool holders with cylindrical shank: — Part 1: Cylindrical shank, location bore — Technical delivery conditions — Part 2: Type A, shanks for tool holders of special designs — Part 3: Type B with rectangular radial seat — Part 4: Type C with rectangular axial seat — Part 5: Type D with more than one rectangular seat — Part 6: Type E with cylindrical seat — Part 7: Type F with taper seat — Part 8: Type Z, accessories iv © ISO 2016 – All rights reserved INTERNATIONAL STANDARD ISO 10889-7:2016(E) Tool holders with cylindrical shank — Part 7: Type F with taper seat Scope This p ar t cond ition s of I SO for 10 8 s p e c i fie s d i men s ion s , de s ignation s , and complementar y te ch nic a l del iver y to ol holders with tap er s e at o f typ e F a nd with a c yl i nd ric a l s han k mounti ng s ys tem i n accordance with ISO 10889-1 I S O 10 8 i s appl ic able to to ol holders with c yl i nd ric a l sh an k p re ferab ly fo r for mach i ne to ol s with non-ro tati ng to ol s , turning machines For non-standardized tool holders with taper seat such as the tool holders shown in Figure 1, it is advi s able to apply the corre s p ond i ng s p e ci fic ation s o f th i s p a r t o f I S O 10 8 Normative references T he fol lowi ng i nd i s p en s able c u ments , i n whole or i n p ar t, a re normatively re ference d i n th i s c u ment a nd a re for its appl ic ation For date d re ference s , on ly the e d ition c ite d appl ie s For u ndate d re ference s , the late s t e d ition o f the re ference d c u ment (i nclud i ng a ny a mend ments) appl ie s ISO 296, Machine tools — Self-holding tapers for tool shanks ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 2768-2, General tolerances — Part 2: Geometrical tolerances for features without individual tolerance indications ISO 10889-1, Tool holders with cylindrical shank — Part 1: Cylindrical shank, location bore — Technical delivery conditions Dimensions All dimensions and tolerances are given in millimetres Tolerancing is done according to ISO 8015 in accordance with ISO 2768-2 Tolerance s no t s p e c i fie d sha l l b e o f tolera nce cl as s “m” i n accorda nce with I S O 76 -1 and o f cla s s “H ” Un s p e ci fie d de ta i l s sh a l l b e cho s en appropriately T he d i men s ion s o f to ol holders typ e F s l l b e i n accordance with the d i men s ion s shown i n and given in Table Figure T he rel ation sh ip b e twe en the s ymb ol s o f th i s p a r t o f I S O 10 8 a nd the s ymb ol s accord i ng to I S O 3 9 is given in Annex A © ISO 2016 – All rights reserved ISO 10889-7:2016(E) Dimensions in millimetres c ? 0,02 ? d₃ h₂ ? d₁ ? d₄ h₁ a b ? d₅ l₂ l₁ l₃ ? d₂ Key a b c Cylindrical s hank in acco rdance with I S O 8 - I nternal M o rs e tap er, typ e B I K in acco rdance with I S O E xternal co o lant s up p ly (clo s ab le) Figure 1 — Taper seat type F tool holder for taper shanks with flat tang Table — Type F tool holder dimensions d 20 25 30 40 50 a Internal Morse taper, type BIK No 1 2 4 T he s e s i z e s h ave a re ce s s d 50 58 68 83 98 fo r 12,065 12,065 17,780 12,065 17,780 17,780 23,825 31,267 17,780 23,825 31,267 h d d h — — — — — 55 58 68 55 58 68 — — — 5 7 — 25 23 25 28 30 32,5 — 35 — tap e r s h a n ks with fl at ta n g up to the end at the discretion of the manufacturer d face Dimensions in millimetres l l l 23 23 27 27 — — — — — 40 48 36 80 36 80 22 63 30 78 55 l 7a — — — 14a — 14a — — — 18 a o f the c yl i nd r ic a l s h a n k T he de s i g n o f s lo t i s © ISO 2016 – All rights reserved ISO 10889-7:2016(E) Table (continued) d1 Internal Morse taper, type BIK No 60 80 a 5 d2 d3 23,825 123 31,267 44,399 31,267 158 44,399 d4 d5 58 68 98 68 98 7 h1 h2 42,5 — 55 — l1 36 50 63 50 l2 l3 30 94 40 104 l4 — — 32 a — — These sizes have a recess for taper shanks with flat tang up to the end face o f the cylindrical shank The design o f slot is at the discretion of the manufacturer Designation A type F tool holder with Morse taper seat in accordance with this part o f ISO 10889 shall be designated by the following: a) “tool holder”; b) re ference to this part o f ISO 10889, i.e ISO 10889-7; c) type (F); d) nominal diameter, d1 , in millimetres; e) internal taper type; f) if applicable, hardened contact surface (H) EXAMPLE A type F tool holder with a Morse taper seat, a nominal diameter, d1 taper, type BIK 3, is designated as follows: = 40 mm, and an internal Tool holder ISO 10889-7 - F - 40 - MT-BIK EXAMPLE A type F tool holder with a Morse taper seat and nominal diameter, d1 = 40 mm, an internal taper, type BIK 3, and hardened contact sur face is designated as follows: Tool holder ISO 10889-7 - F - 40 - MT-BIK H Technical delivery conditions As a complement to the requirements o f ISO 10889-1, the following requirements also apply The taper socket shall be hardened with a surface hardness of (56 +04 ) HRC and a depth of hardening of at least 0,5 mm The taper angle tolerance class of taper socket shall be AT5 in accordance with ISO 296 Tool holders can also be supplied with hardened contact surface © ISO 2016 – All rights reserved ISO 10889-7:2016(E) Annex A (informative) Relationship between designations in this part of ISO 10889 and ISO 13399 For the relationship between the symbols o f this part o f ISO 10889 and the symbols according to ISO 13399, see Table A.1 Table A.1 — Relationship between symbols in this part of ISO 10889 and ISO 13399 Symbol in this part of ISO 10889 Figure d3 Figure Figure d5 l1 l2 l3 l4 h1 h2 Figure Figure Figure Figure Figure Figure Figure Figure d d d a Reference in this part of ISO 10889 Property Symbol in name in ISO 13399 series ISO 13399 series connection DCONMS diameter machine side flange diameter DF functional DFC diameter body diameter DB — — protruding length LPR flange thickness FLGT shank length LS — — — OAH a – RADH radial height RADH OAH is the “overall height” (code BSU 71D078EB73E87) Reference in ISO 13399 series BSU code 71EBDBF5060E6 71EC61D8A1771 7272379AD9C85 71ED6A9AF7D1D — 71DCD394BB20E 71EEF53809764 71CF298870946 — — 726E3E86B5284 © ISO 2016 – All rights reserved ISO 10889-7:2016(E) Bibliography [1] [2] ISO 8015, Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules ISO 13399 (all parts), Cutting tool data representation and exchange © ISO 2016 – All rights reserved ISO 0889-7: 01 6(E) ICS 060.2 Price based on pages © ISO 2016 – All rights reserved