© ISO 2016 Tool holders with cylindrical shank — Part 4 Type C with rectangular axial seat Porte outil à queue cylindrique — Partie 4 Porte outil axial de type C INTERNATIONAL STANDARD ISO 10889 4 Thi[.]
INTERNATIONAL STANDARD ISO 10889-4 Third edition 2016-03-15 Tool holders with cylindrical shank — Part 4: Type C with rectangular axial seat Porte-outil queue cylindrique — Partie 4: Porte-outil axial de type C Reference number ISO 10889-4:2016(E) © ISO 2016 ISO 10889-4:2016(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2016, Published in Switzerland All rights reserved Unless otherwise specified, no part o f this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country o f the requester ISO copyright o ffice Ch de Blandonnet • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel +41 22 749 01 11 Fax +41 22 749 09 47 copyright@iso.org www.iso.org ii © ISO 2016 – All rights reserved ISO 10889-4:2016(E) Contents Page Foreword iv Scope Normative references Dimensions Geometrical tolerances Designation 6 Technical delivery conditions General Design f Annex A (informative) Relationship between designations in this part of ISO 10889 and 6.1 6.2 6.3 S co p e o delivery ISO 13399 Bibliography 10 © ISO 2016 – All rights reserved iii ISO 10889-4:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work o f preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o f electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part In particular the different approval criteria needed for the di fferent types o f ISO documents should be noted This document was dra fted in accordance with the editorial rules of the ISO/IEC Directives, Part (see www.iso.org/directives) Attention is drawn to the possibility that some o f the elements o f this document may be the subject o f patent rights ISO shall not be held responsible for identi fying any or all such patent rights Details o f any patent rights identified during the development o f the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents) Any trade name used in this document is in formation given for the convenience o f users and does not constitute an endorsement For an explanation on the meaning o f ISO specific terms and expressions related to formity assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary in formation The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, Holding tools, adaptive items and interfaces This third edition cancels and replaces the second edition (ISO 10889-4:2004), of which it constitutes a minor revision, notably with the addition o f Annex A, which gives the relationship between the designations of this part of ISO 10889 and the ISO 13399 series ISO 10889 consists of the following parts, under the general title Tool holders with cylindrical shank: — Part 1: Cylindrical shank, location bore — Technical delivery conditions — Part 2: Type A, shanks for tool holders of special designs — Part 3: Type B with rectangular radial seat — Part 4: Type C with rectangular axial seat — Part 5: Type D with more than one rectangular seat — Part 6: Type E with cylindrical seat — Part 7: Type F with taper seat — Part 8: Type Z, accessories iv © ISO 2016 – All rights reserved INTERNATIONAL STANDARD ISO 10889-4:2016(E) Tool holders with cylindrical shank — Part 4: Type C with rectangular axial seat Scope This part of I SO cond ition s for 10 8 s p e c i fie s d i men s ion s , de s ignation s a nd complementar y te ch n ic a l del iver y to ol holders with a re c tangu lar a xia l s e at o f typ e s C1 to C with c yl i nd ric a l sh an k i n accordance with ISO 10889-1 I S O 10 8 i s appl ic able to to ol holders with c yl i nd ric a l s n k pre ferably for for mach i ne to ol s with non-ro tati ng to ol s , turn i ng mach i ne s For non-standardized tool holders with rectangular axial seat, such as the tool holders shown in Figures to f f , it i s advi s able to apply the corre s p ond i ng s p e ci fic ation s o th i s p ar t o I S O 10 8 Normative references T he fol lowi ng i nd i s p en s able c u ments , i n whole or i n p ar t, are normatively re ference d i n th i s c u ment a nd are for its appl ic ation For date d re ference s , on ly the e d ition cite d appl ie s For u ndate d re ference s , the late s t e d ition o f the re ference d c u ment (i nclud i ng any amend ments) appl ie s ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 2768-2, General tolerances — Part 2: Geometrical tolerances for features without individual tolerance indications ISO 8015, Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules ISO 10889-1, Tool holders with cylindrical shank — Part 1: Cylindrical shank, location bore — Technical delivery conditions Dimensions All dimensions and tolerances are given in millimetres Tolerancing is done according to ISO 8015 f f in accordance with ISO 2768-2 Tolerance s no t s p e c i fie d sh a l l b e o tolerance clas s “m” i n accorda nce with I S O 76 -1 and o cla s s “H ” Un s p e ci fie d de ta i l s s l l b e cho s en appropriately T he d i men s ion s o f to ol holders typ e C s l l b e i n accordance with the d i men s ion s shown i n and given in Table Figures to T he rel ation sh ip b e twe en the s ymb ol s o f th i s p ar t o f I S O 10 8 and the s ymb ol s accord i ng to I S O 3 9 is given in Annex A © ISO 2016 – All rights reserved ISO 10889-4:2016(E) Rz 16 l1 b1 l2 b2 a α h h1 h3 h8 h6 ? d1 h4 h5 15˚ 15˚ b l3 Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type C1 tool holder, right-hand © ISO 2016 – All rights reserved ISO 10889-4:2016(E) Rz 16 b4 b5 l1 l b6 15˚ h h1 h h8 h6 h2 ? d1 h5 a 15˚ α l Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type C2 tool holder, left-hand © ISO 2016 – All rights reserved ISO 10889-4:2016(E) b1 b2 Rz 16 b3 l1 h7 h2 h3 ? d1 h h1 15˚ a h9 h6 α 15˚ l2 l3 Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type C3 tool holder, overhead, right-hand © ISO 2016 – All rights reserved ISO 10889-4:2016(E) b4 Rz 16 b5 b6 a 15˚ h h7 h ? d1 h2 h1 h9 h6 α 15˚ l2 l1 l Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type C4 tool holder, overhead, left-hand Table — Type C tool holder dimensions d b b b + 0,3 b b Types C1 and C3 16 20 25 30 40 50 60 80 43 24 52 27 65 40 58 33 70 35 85 42,5 100 50 125 62,5 160 80 13 13 26 19 17 21 26 33 42 b + 0,3 Types C1 and C4 43 24 — — 65 40 58 33 76 41 90 47,5 105 55 125 62,5 160 78 © ISO 2016 – All rights reserved 13 — 26 19 23 25,5 30,5 33 42 h1 +0 − 0,1 max 12 17 15 15 20 22 20 19 19 16 22 19 19 25 30 25 23 23 16 20 25 32 32 40 22 29 34 41 41 53 22,5 26 35 42 46 60 22,5 25 30 25 25 25 22 28 38 35 30 28 30 32,5 48 42,5 — — 35 35 60 50 — — 42,5 42,5 62,5 62,5 — — 55 55 80 80 — — h h h h h Dimensions in millimetres h h h l l l 44 20 55 30 50 — 55 20 70 10 30 85 12,5 30 100 16 40 125 16 40 160 20 40 α 30° 30° 30° 25° — — — — ISO 10889-4:2016(E) Geometrical tolerances The geometrical tolerances shall be as defined in Figure Dimensions in millimetres 60˚ Figure — Geometrical tolerances Designation A type C tool holder with rectangular axial seat in accordance with this part o f ISO 10889 shall be designated by the following: a) “Tool holder”; b) re ference to this part o f ISO 10889, i.e ISO 10889-4; c) type (C1, C2, C3 or C4), d) e) f) nominal diameter, , in millimetres; nominal height, , in millimetres; nominal length, , in millimetres, only if = 20 mm EXAMPLE d h l d A tool holder with rectangular axial seat o f type C1 with a nominal diameter, d1 = 60 mm and a nominal height, = 32 mm, is designated as follows: h Tool holder ISO 10889-4 - C1 - 60 × 32 EXAMPLE A tool holder with rectangular axial seat o f type C1 with a nominal diameter, d1 nominal height, = 16 mm, and a nominal length, = 55 mm, is designated as follows: h = 20 mm, a l Tool holder ISO 10889-4 - C1 - 20 × 16 × 55 Technical delivery conditions 6.1 General As a complement to the requirements of ISO 10889-1, those given in 6.2 and 6.3 also apply 6.2 Design Tool holders with a rectangular axial seat are equipped with a coolant outlet with adjustable direction The design is at the discretion o f the manu facturer, e.g ball-type nozzle © ISO 2016 – All rights reserved ISO 10889-4:2016(E) The tools shall be adjustable in the tool holder at right angles to the rectangular seat The design is at the discretion of the manufacturer It shall be possible to reduce the dimension h1 specified in Table to the next smallest standardized dimension h1 as given in Table The design is at the discretion of the manufacturer Table — Smaller standardized dimension, h d1 h1 16 10 20 12 25 12 30 16 40 20 50 25 Dimensions in millimetres 60 25 80 32 Tool holders may also be supplied with a hardened contact sur face It shall be then mentioned in the designation (H for hardened contact surface) EXAMPLE A tool holder with rectangular axial seat o f type C1 with a nominal diameter, d1 nominal height, h1 = 20 mm, with hardened contact surface is designated as follows: = 40 mm, a Tool holder ISO 10889-4 - C1 - 40 × 20 H 6.3 Scope of delivery The scope o f delivery o f tool holders includes clamping elements for the clamping o f the tools The design of the clamping elements is at the discretion of the manufacturer © ISO 2016 – All rights reserved ISO 10889-4:2016(E) Annex A (informative) Relationship between designations in this part of ISO 10889 and ISO 13399 For the relationship between the symbols o f this part o f ISO 10889 and symbols according to ISO 13399, see Table A.1 Table A.1 — Relationship between symbols in this part of ISO 10889 and ISO 13399 Symbol in this part of ISO 10889 Figures to b2 Figures and Figures and Figures and Figures and Figures and Figures and d b b b b b h h Figures to Figures to Figures to Figures to Figures to h Figures to h Figures to h6 h7 h8 h9 Figures to Figures to Figures to Figures to Figures to l l3 l h a Reference in this part of Property name ISO 10889 in ISO 13399 OAH is the “overall height” (code BSU 71D078EB73E87) Symbol in ISO 13399 connection diameter maDCONMS chine side overall width OAW radial width RADW functional WF width overall width OAW radial width RADW functional WF width protruding LPR length — — — — functional HF height — — radial height chamfer disRHCDL tance lower radial height chamfer disRHCDU tance upper — OAH a – RADH radial height RADH — OAH a – RADH — — — — Reference in ISO 13399 (BSU code) 71EBDBF5060E6 71CF299257986 726E3E8DA5589 71CF29984CDA7 71CF299257986 726E3E8DA5589 71CF29984CDA7 71DCD394BB20E — — 71CF29994E737 — 726E3E8F925AC 726E3E9005480 — 726E3E86B5284 — — — © ISO 2016 – All rights reserved ISO 10889-4:2016(E) Table A.1 (continued) Symbol in this part of ISO 10889 a Reference in this part of Property name ISO 10889 in ISO 13399 Figures to 15° Figures to 15° Figures to OAH is the “overall height” (code BSU 71D078EB73E87) © ISO 2016 – All rights reserved radial offset height radial height chamfer angle lower radial height chamfer angle upper Symbol in ISO 13399 Reference in ISO 13399 (BSU code) RADHOF 726E3E8AF37E4 RHCAL 726E3E8E6CEE3 RHCAU 726E3E8F2AE05 ISO 10889-4:2016(E) Bibliography [1] [2] ISO 8015, Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules ISO 13399 (all parts), Cutting tool data representation and exchange 10 © ISO 2016 – All rights reserved ISO 0889-4: 01 6(E) ICS 060.2 Price based on 10 pages © ISO 2016 – All rights reserved