© ISO 2016 Tool holders with cylindrical shank — Part 3 Type B with rectangular radial seat Porte outil à queue cylindrique — Partie 3 Porte outil radial de type B INTERNATIONAL STANDARD ISO 10889 3 T[.]
INTERNATIONAL STANDARD ISO 10889-3 Third edition 2016-03-01 Tool holders with cylindrical shank — Part 3: Type B with rectangular radial seat Porte-outil queue cylindrique — Partie 3: Porte-outil radial de type B Reference number ISO 10889-3:2016(E) © ISO 2016 ISO 10889-3:2016(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2016, Published in Switzerland All rights reserved Unless otherwise specified, no part o f this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country o f the requester ISO copyright o ffice Ch de Blandonnet • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel +41 22 749 01 11 Fax +41 22 749 09 47 copyright@iso.org www.iso.org ii © ISO 2016 – All rights reserved ISO 10889-3:2016(E) Contents Page Foreword iv Scope Normative references Dimensions Geometrical tolerances Designation Technical delivery conditions General Design f Annex A (informative) Relationship between designations in this part of ISO 10889 and 6.1 6.2 6.3 S co p e o delivery ISO 13399 10 Bibliography 11 © ISO 2016 – All rights reserved iii ISO 10889-3:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work o f preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o f electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part In particular the different approval criteria needed for the di fferent types o f ISO documents should be noted This document was dra fted in accordance with the editorial rules of the ISO/IEC Directives, Part (see www.iso.org/directives) Attention is drawn to the possibility that some o f the elements o f this document may be the subject o f patent rights ISO shall not be held responsible for identi fying any or all such patent rights Details o f any patent rights identified during the development o f the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents) Any trade name used in this document is in formation given for the convenience o f users and does not constitute an endorsement For an explanation on the meaning o f ISO specific terms and expressions related to formity assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary in formation The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, Holding tools, adaptive items and interfaces This third edition cancels and replaces the second edition (ISO 10889-3:2004), of which it constitutes a minor revision, notably with the addition o f Annex A, which gives the relationship between the designations of this part of ISO 10889 and the ISO 13399 series ISO 10889 consists of the following parts, under the general title Tool holders with cylindrical shank: — Part 1: Cylindrical shank, location bore — Technical delivery conditions — Part 2: Type A, shanks for tool holders of special designs — Part 3: Type B with rectangular radial seat — Part 4: Type C with rectangular axial seat — Part 5: Type D with more than one rectangular seat — Part 6: Type E with cylindrical seat — Part 7: Type F with taper seat — Part 8: Type Z, accessories iv © ISO 2016 – All rights reserved INTERNATIONAL STANDARD ISO 10889-3:2016(E) Tool holders with cylindrical shank — Part 3: Type B with rectangular radial seat Scope This p ar t o f I S O cond ition s for 10 8 s p e ci fie s d i men s ion s , de s ignation s , and complementar y te ch n ic a l del iver y to ol holders with a re c tangu lar rad ia l s e at o f typ e s B to B with c yl i nd ric a l s han k i n accordance with ISO 10889-1 I S O 10 8 i s appl ic able to to ol holders with c yl i nd ric a l s n k pre ferably for for mach i ne to ol s with non-ro tati ng to ol s , turn i ng mach i ne s For non-standardized tool holders with a rectangular radial seat such as the tool holders shown in the figu re s , it i s advi s able to apply the corre s p ond i ng s p e ci fic ation s o f th i s p ar t o f I S O 10 8 Normative references T he fol lowi ng i nd i s p en s able c u ments , i n whole or i n p ar t, are normatively re ference d i n th i s c u ment a nd are for its appl ic ation For date d re ference s , on ly the e d ition cite d appl ie s For u ndate d re ference s , the late s t e d ition o f the re ference d c u ment (i nclud i ng any amend ments) appl ie s ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 2768-2, General tolerances — Part 2: Geometrical tolerances for features without individual tolerance indications ISO 10889-1, Tool holders with cylindrical shank — Part 1: Cylindrical shank, location bore — Technical delivery conditions Dimensions All dimensions and tolerances are given in millimetres Tolerancing is done according to ISO 8015 f f in accordance with ISO 2768-2 Tolerance s no t s p e c i fie d sh a l l b e o tolerance clas s “m” i n accorda nce with I S O 76 -1 and o cla s s “H ” Un s p e ci fie d de ta i l s s l l b e cho s en appropriately T he d i men s ion s o f to ol holders typ e B sh a l l b e i n accordance with the d i men s ion s shown i n and given in Table Figures to T he rel ation sh ip b e twe en the s ymb ol s o f th i s p ar t o f I S O 10 8 and the s ymb ol s accord i ng to I S O 3 9 is given in Annex A © ISO 2016 – All rights reserved ISO 10889-3:2016(E) Rz 16 b1 l2 b2 l1 b3 a h3 h8 h6 ϕd1 h1 h2 h4 h5 15˚ 15˚ α Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type B1 tool holder, right-hand, short Rz 16 b1 l2 b2 l1 b3 a h4 ϕd1 h3 h6 h8 h1 h2 h5 15˚ α 15˚ Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type B2 tool holder, left-hand, short © ISO 2016 – All rights reserved ISO 10889-3:2016(E) Rz 16 l2 l1 α 15˚ h6 h4 h7 h3 ϕd1 h1 h2 h9 a 15˚ b3 b2 b1 Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type B3 tool holder, overhead, right-hand, short Rz 16 l2 l1 α 15˚ h4 h7 h3 ϕd1 h1 h2 h9 h6 a 15˚ b3 b2 b1 Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type B4 tool holder, overhead, left-hand, short © ISO 2016 – All rights reserved ISO 10889-3:2016(E) Rz 16 b1 b2 b3 a α h6 h3 ϕd1 h8 h1 h2 h4 h5 15˚ 15˚ l1 l2 45 ˚ Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type B5 tool holder, right-hand, long © ISO 2016 – All rights reserved ISO 10889-3:2016(E) Rz 16 b1 b2 b3 15˚ h4 h6 h3 ϕd1 h8 h1 h2 h5 a α 15˚ l1 l2 45 ˚ Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type B6 tool holder, left-hand, long © ISO 2016 – All rights reserved ISO 10889-3:2016(E) Rz 16 h4 h7 h3 ϕd1 h2 h1 h8 a h6 15˚ α 15˚ l1 b3 b2 l2 b1 45 ˚ Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type B7 tool holder, overhead, right-hand, long © ISO 2016 – All rights reserved ISO 10889-3:2016(E) Rz 16 15˚ h7 h3 ϕd1 h4 h6 h9 h1 h2 a α 15˚ b3 l1 l2 b2 b1 45 ˚ Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type B8 tool holder, overhead, left-hand, long © ISO 2016 – All rights reserved ISO 10889-3:2016(E) Table — Type B tool holder dimensions d 16 b1 Type B b2 Type B b to to to to 42 58 23 39 h _ 0,1 h max h h h h h Dimensions in millimetres h h l α 12 17 15 15 20 22 20 19 19 20 55 75 30 50 16 22 19 19 25 30 25 23 23 25 55 75 30 50 16 22 22,5 22,5 25 30 25 25 25 30 70 85 100 125 160 100 35 65 10 118 42,5 75,5 12,5 130 50 80 16 145 62,5 82,5 16 190 80 110 20 20 25 32 32 40 29 34 41 41 53 40 50 60 80 l + 0,5 26 35 42 46 60 22 30 35 42,5 55 28 32,5 35 42,5 55 38 48 60 62,5 80 35 42,5 50 62,5 80 30 — — — — 28 — — — — 13 23 16 26 16 26 22 42 22 30 30 40 24 34 30 40 30 40 40 60 44 55 60 75 30° 30° 30° 25° — — — — Geometrical tolerances The geometrical tolerances shall be as defined in Figure 0,1/100 A 0,05 60 ˚ A Figure — Geometrical tolerances Designation A type B tool holder with rectangular radial seat in accordance with this part o f ISO 10889 shall be designated by the following: a) “Tool holder”; b) re ference to this part o f ISO 10889, i.e ISO 10889-3; c) type (B1, B2, B3, B4, B5, B6, B7, or B8); d) e) nominal diameter, , in millimetres; nominal height, , in millimetres; d h © ISO 2016 – All rights reserved ISO 10889-3:2016(E) f) head length, , in millimetres l EXAMPLE A tool holder with rectangular radial seat o f type B1 with a nominal diameter d1 nominal height = 32 mm, and a head length = 60 mm is designated as follows: h = 60 mm, a l Tool holder ISO 10889-3 - B1 - 60 × 32 × 60 Technical delivery conditions 6.1 General As a complement to the requirements of ISO 10889-1, those given in 6.2 and 6.3 shall also apply 6.2 Design Tool holders with rectangular radial seat are equipped with a coolant outlet with adjustable direction The design is at the discretion o f the manu facturer, e.g ball-type nozzle The tools shall be adjustable in the tool holder at right angles to the rectangular seat The design is at the discretion of the manufacturer It shall be possible to reduce the dimension specified in Table to the next smallest standardized dimension as given in Table The design is at the discretion of the manufacturer h h Table — Smaller standardized dimension h 16 h1 d 10 20 12 25 30 12 16 40 20 50 25 Dimensions in millimetres 60 80 25 32 Tool holders may also be supplied with a hardened contact sur face Then it shall be mentioned in the designation (H for hardened contact surface) A tool holder with rectangular radial seat o f type B1 with a nominal diameter = 40 mm, a nominal height = 20 mm, and a head length = 44 mm with hardened contact surface is designated as follows: EXAMPLE d h l Tool holder ISO 10889-3 - B1 -40 × 20 × 44 H 6.3 Scope of delivery The scope o f delivery o f tool holders includes clamping elements for the clamping o f the tools The design of the clamping elements is at the discretion of the manufacturer © ISO 2016 – All rights reserved ISO 10889-3:2016(E) Annex A (informative) Relationship between designations in this part of ISO 10889 and ISO 13399 For the relationship between the symbols o f this part o f ISO 10889 and symbols according to ISO 13399, see Table A.1 Table A.1 — Relationship between symbols in this part of ISO 10889 and ISO 13399 Symbol in this part of ISO 10889 Figures to b2 b3 l1 l2 h1 h2 h3 Figures to Figures to Figures to Figures to Figures to Figures to Figures to Figures to Figures to h6 h7 h8 h9 15° Figures to Figures to Figures to Figures to Figures to Figures to Figures to 15° Figures to d b h h a 10 Reference in this part of ISO 10889 Property name in ISO 13399 connection diameter machine side overall width radial width Radial offset width functional length protruding length functional height — radial height chamfer distance lower radial height chamfer distance upper — radial height — — — Radial offset height radial height chamfer angle lower radial height chamfer angle upper Symbol in ISO 13399 Reference in ISO 13399 (BSU code) DCONMS 71EBDBF5060E6 OAW RADW RADWOF LF LPR HF — RHCDL 71CF299257986 726E3E8DA5589 726E3E8E0AE97 71DCD39338974 71DCD394BB20E 71CF29994E737 — 726E3E8F925AC RHCDU 726E3E9005480 OAH a – RADH RADH OAH a –RADH — — RADHOF RHCAL — 726E3E86B5284 — — — 726E3E8AF37E4 726E3E8E6CEE3 RHCAU 726E3E8F2AE05 OAH is the “overall height” (code BSU 71D078EB73E87) © ISO 2016 – All rights reserved ISO 10889-3:2016(E) Bibliography [1] [2] ISO 8015, Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules ISO 13399 (all parts), Cutting tool data representation and exchange © ISO 2016 – All rights reserved 11 ISO 0889-3 : 01 6(E) ICS 060.2 Price based on 11 pages © ISO 2016 – All rights reserved