© ISO 2016 Tool holders with cylindrical shank — Part 5 Type D with more than one rectangular seat Porte outil à queue cylindrique — Partie 5 Porte outil de type D comportant plusieurs logements INTER[.]
INTERNATIONAL STANDARD ISO 10889-5 Second edition 2016-03-15 Tool holders with cylindrical shank — Part 5: Type D with more than one rectangular seat Porte-outil queue cylindrique — Partie 5: Porte-outil de type D comportant plusieurs logements Reference number ISO 10889-5:2016(E) © ISO 2016 ISO 10889-5:2016(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2016, Published in Switzerland All rights reserved Unless otherwise specified, no part o f this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country o f the requester ISO copyright o ffice Ch de Blandonnet • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel +41 22 749 01 11 Fax +41 22 749 09 47 copyright@iso.org www.iso.org ii © ISO 2016 – All rights reserved ISO 10889-5:2016(E) Contents Page Foreword iv Scope Normative references Dimensions Geometrical tolerances Designation Technical delivery conditions General Design f Annex A (informative) Relationship between designations in this part of ISO 10889 and 6.1 6.2 6.3 S co p e o delivery ISO 13399 Bibliography © ISO 2016 – All rights reserved iii ISO 10889-5:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work o f preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o f electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part In particular the different approval criteria needed for the di fferent types o f ISO documents should be noted This document was dra fted in accordance with the editorial rules of the ISO/IEC Directives, Part (see www.iso.org/directives) Attention is drawn to the possibility that some o f the elements o f this document may be the subject o f patent rights ISO shall not be held responsible for identi fying any or all such patent rights Details o f any patent rights identified during the development o f the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents) Any trade name used in this document is in formation given for the convenience o f users and does not constitute an endorsement For an explanation on the meaning o f ISO specific terms and expressions related to formity assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary in formation The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, Holding tools, adaptive items and interfaces This second edition cancels and replaces the first edition (ISO 10889-5:1997), o f which it constitutes a minor revision, notably with the addition o f Annex A, which gives the relationship between the designations of this part of ISO 10889 and the ISO 13399 series ISO 10889 consists of the following parts, under the general title Tool holders with cylindrical shank: — Part 1: Cylindrical shank, location bore — Technical delivery conditions — Part 2: Type A, shanks for tool holders of special designs — Part 3: Type B with rectangular radial seat — Part 4: Type C with rectangular axial seat — Part 5: Type D with more than one rectangular seat — Part 6: Type E with cylindrical seat — Part 7: Type F with taper seat — Part 8: Type Z, accessories iv © ISO 2016 – All rights reserved INTERNATIONAL STANDARD ISO 10889-5:2016(E) Tool holders with cylindrical shank — Part 5: Type D with more than one rectangular seat Scope This part of I SO cond ition s for 10 8 s p e c i fie s d i men s ion s , de s ignation s a nd complementar y te ch n ic a l del iver y to ol holders with more th an one re c ta ngu la r s e at o f typ e s D1 and D2 with c yl i nd ric a l shank in accordance with ISO 10889-1 I S O 10 8 i s appl ic able to to ol holders with c yl i nd ric a l s n k pre ferably for for mach i ne to ol s with non-ro tati ng to ol s , turn i ng mach i ne s For non-standardized tool holders with more than one rectangular seat, such as tool holders as shown in Figures to f f , it i s advi s able to apply the corre s p ond i ng s p e c i fic ation s o th i s p ar t o I S O 10 8 Normative references T he fol lowi ng i nd i s p en s able c u ments , i n whole or i n p ar t, are normatively re ference d i n th i s c u ment a nd are for its appl ic ation For date d re ference s , on ly the e d ition cite d appl ie s For u ndate d re ference s , the late s t e d ition o f the re ference d c u ment (i nclud i ng any amend ments) appl ie s ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 2768-2, General tolerances — Part 2: Geometrical tolerances for features without individual tolerance indications ISO 10889-1, Tool holders with cylindrical shank — Part 1: Cylindrical shank, location bore — Technical delivery conditions Dimensions All dimensions and tolerances are given in millimetres Tolerancing is done according to ISO 8015 f f in accordance with ISO 2768-2 Tolerance s no t s p e c i fie d sh a l l b e o tolerance clas s “m” i n accorda nce with I S O 76 -1 and o cla s s “H ” Un s p e ci fie d de ta i l s s l l b e cho s en appropriately T he d i men s ion s o f to ol holders typ e D sha l l b e i n accordance with the d i men s ion s shown i n and and given in Table Figures T he relation s h ip b e twe en the s ymb ol s o f th i s p ar t o f I S O 10 8 a nd the s ymb ol s accord i ng to I S O 3 9 is given in Annex A © ISO 2016 – All rights reserved ISO 10889-5:2016(E) Rz 16 l b b1 l1 b4 b2 ?d1 h4 h6 h1 h2 h3 α Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type D1 tool holder Rz 16 b3 b2 h5 ?d1 h2 h1 h7 h4 α b4 b1 l1 l2 Key a Cylindrical s hank in acco rdance with I S O 8 - NOTE Surface roughness is given in micrometres Figure — Type D2 tool holder © ISO 2016 – All rights reserved ISO 10889-5:2016(E) Table — Type D tool holder dimensions d h - 0, 25 30 40 50 60 80 16 20 25 32 32 40 h h max h h h h b b +0 b , 25 30 25 28 38 34 32,5 48 42,5 35 60 50 42,5 62,5 62,5 55 80 80 25 30 — — — — 25 28 — — — — 33 35 42,5 50 57,5 76 19 17 21 26 33 42 b +0 , 22 29 34 41 41 53 Dimensions in millimetres l +0 α 48 60 72 85 110 140 30° 25° — — — — l , 33 19 34 41 23 42 47,5 25,5 50 55 30,5 60 57,5 33 85 76 42 105 Geometrical tolerances Geometrical tolerances shall be as defined in Figure 60˚ Figure — Geometrical tolerances Designation A type D tool holder with more than one rectangular seat in accordance with this part o f ISO 10889 shall be designated by the following: a) “Tool holder”; b) re ference to this part o f ISO 10889, i.e ISO 10889-5; c) type (D1 or D2); d) e) nominal diameter, , in millimetres; nominal height, , in millimetres EXAMPLE d h A tool holder with more than one rectangular seat o f type D1 with a nominal diameter, d1 = 60 mm, and a nominal height, = 32 mm, is designated as follows: h Tool holder ISO 10889-5 - D1 - 60 ì 32 â ISO 2016 All rights reserved ISO 10889-5:2016(E) Technical delivery conditions 6.1 General As a complement to the requirements of ISO 10889-1, those given in 6.2 and 6.3 a l s o apply 6.2 Design To ol holders with more than one re c ta ngu l ar s e at a re e quipp e d with a co olant s upply with adj u s tab le direction The design is at the discretion of the manufacturer T he to ol s s l l b e adj u s table i n the to ol holder at right angle s to the re c tangu lar s e at T he de s ign i s at the discretion of the manufacturer 6.3 Scope of delivery T he s cop e o f del iver y o f to ol holders i nclude s cla mpi ng elements for the clampi ng o f the to ol s T he design of the clamping elements is at the discretion of the manufacturer © ISO 2016 – All rights reserved ISO 10889-5:2016(E) Annex A (informative) Relationship between designations in this part of ISO 10889 and ISO 13399 For the relationship between the symbols o f this part o f ISO 10889 and symbols according to ISO 13399 , see Table A.1 Table A.1 — Relationship between symbols in this part of ISO 10889 and ISO 13399 Symbol in this part of Reference in this part Property name ISO 10889 of ISO 10889 in ISO 13399 b3 b4 l1 l2 h1 h2 Figures and Figures and Figures and Figures and Figures and Figures and Figures and Figures and Figures and connection diameter machine side radial width functional width functional width radial width functional length protruding length functional height — Figure — h6 h7 Figures and Figure Figure Figure Figure radial height — — — — d b b h h h a b α To be indexed Symbol in ISO 13399 Reference in ISO 13399 (BSU code) DCONMS RADWa WFa WFa RADWa LF LPR HF — 71EBDBF5060E6 726E3E8DA5589 71CF29984CDA7 71CF29984CDA7 726E3E8DA5589 71DCD39338974 71DCD394BB20E 71CF29994E737 — OAH b — RADH RADH OAH b — RADH — — — — 726E3E86B5284 — — — — OAH is the “overall height” (code BSU 71D078EB73E87) shall be number and b3 number b shall be number and b number b © ISO 2016 – All rights reserved ISO 10889-5:2016(E) Bibliography [1] [2] ISO 8015, Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules ISO 13399 (all parts), Cutting tool data representation and exchange © ISO 2016 – All rights reserved ISO 0889-5 : 01 6(E) ICS 060.2 Price based on pages © ISO 2016 – All rights reserved