... độ cân trục khuỷu, bánh đà - Thiết bị nắn thanhtruyền - Máy ép thuỷ lực - Máy chiếu Overhead - Projector - Máy mài trục khuỷu máy doa bạc lót truyền - Thiết bị hàn - Máy khoan Dụng cụ: - Pan ... Trang thiết bị, đồ dùng dạy học: - Động xăng, điêzen - Mô hình cắt động - Máy chiếu Overhead - Projector phần mềm mô tháo lắp phận chuyển động - Bộ dụng cụ cầm tay nghề sửa chữa ôtô, - Dụng cụ ... Các loại pit tông - Bản vẽ treo tờng pit tông - Phim pit tông - Slide học - Máy chiếu overhead - Projector - Pan me đo ngoài, - Thớc cặp, - Kính phóng đại, - Thanh kim loại, - Căn lá, lực kế Địa...
... liệt kê nguồn lực cần thiết cho mô đun Dụng cụ trang thiết bi: - Động ô tô - Máy chiếu Overhead - Projector - Bộ dụng cụ cầm tay nghề sửa chữa ôtô - Căn lá, thớc thẳng - Pan me, thớc cặp - Mặt phẳng ... dùng dạy học: - Động xăng, điêzen - Bản vẽ cấu tạo loại hệ thống làm mát - Máy chiếu Overhead - Projector - Slide phần mềm mô tháo lắp phận hệ thống làm mát - Bộ dụng cụ cầm tay nghề sửa chữa ... dạy học: - Động ôtô - Một số bơm nớc - Bản vẽ treo tờng bơm nớc ly tâm - Slide nội dung giảng - Projector - Pan me đo - Thớc cặp - Đồng hồ so - Căn - Máy mài xu páp - Giá đỡ xu páp - Dụng cầm...
... diameter of drums after grinding Width of linings Thickness of linings (including mounting) Minimum thickness of linings (including mounting) Diameter of discs Thickness of discs Minimum thickness of ... (dimensions in mm) Diameter of slave cylinders Diameter of discs Thickness of discs Minimum thickness of discs (1) Thickness of linings (including mounting) Minimum thickness of linings (including ... Trolley jack - Axle stands 02 LIFTING WITH THE TROLLEY JACK FROM THE SIDE AXLE STANDS Use pad Cha 280-02 When taking the weight of the vehicle on the axle stands ensure that the stands are under the...
... to prevent the entry of water which, even in very small quantities, will reduce the quality of the oil and result in seizure of the gearbox or of the final drive STORAGE AND USE Special care ... rubber protector, and pull the fork towards the inside of the clutch casing Check the extent of fork travel It should be: REFITTING X = 17 to 18 mm Coat the walls of the guide tube and the fork pads ... diameter of the bushing with Loctite FRENBLOC Using a tube with an external diameter of 38 mm, fit the bush fully into the crankshaft bore Observe the direction of fitting of the bush and check...
... of the steering wheel rim Move the steering to full lock in the other direction whilst counting the number of turns and fractions of a turn Return to half the number of turns (and fractions of ... direction of fitting : - on the outside, the pad and the groove (B) are offset towards the front of the vehicle, - on the inside, the pad and the groove (B) are offset towards the rear of the vehicle, ... effect of the geometry angles The effect of the different geometry angles on the steering of the vehicle and on its tyre wear Differences in the variation of the parallelism between the right and...
... 475 and check if the flap is stuck Repair wiring between tracks: - A2 of connector R99 andof relay 690 - of relay 690 and B1 of the recycling motor connector - the shunt between A1 and B1 of ... X53A of relay 474 and the compressor Check for + 12 Volts between tracks andof relay 474 Is there + 12 Volts ? no X53A Repair the wiring between track of relay 474 and splice A in the wiring of+ ... continuity between tracks : - of relay 417 and B3 of connector R99 - B3 of connector R99 and B3 of the control panel 319 Is this correct? yes Passenger compartment fan operating and AC on MAX Disconnect...
... rear section of the trim on the roof roll-over bar and clip Check the tension of the trim Rivet the trim to the main roof arch (rear side) Stick the trim to the rear hood frame and re- secure ... described below must be carried out on both the left hand and right hand sides Any incorrect operation of the hood triggers an alarm The order of operations must be followed PRF7303 Opening the ... the unlocking handle (this opens the rear hood locks and the hood compartment) Lift the rear of the hood Remove the safety device and open the hood compartment Fold the rear section of the hood...
... "ATHLET" ROOF BARS For the Renault 19 56 "ATHLET" ROOF BARS For the Renault 19 56 "CARRY ALL" BARS 5-door Renault 19 56 "CARRY ALL" BARS 5-door Renault 19 56 SPECIAL FRONT MUD FLAPS and door Renault ... FLAPS and door Renault 19 56 DEFLECTORS and door Renault 19 56 BRITAX 2110 MODEL MEDIUM-SIZED SUNROOF Fitting instructions 56 BRITAX 2110 MEDIUM-SIZED SUNROOF Fitting instructions 56 ...
... anti-chipping and anti-corrosion mastic with two parts L = 330 40-18 GENERAL Description of symbols LOCATION OF OPERATIONS TYPES OF TOOL AND ORDER OF OPERATIONS LOCATION OF OPERATIONS 40 TYPES OF TOOL AND ... JOINTS rotary grind sand bead of mastic in cartridge unpick clean bead and spraying of mastic ANTI-CHIPPING PROTECTION grind spraying of mastic release brazed joint sand PROTECTION OF HOLLOW SECTIONS ... panels and prevents corrosion of the spot welds Application of aluminium based paint This must be applied to the mating surfaces of each of the parts to be plug welded This paint is conductive and...
... EXPLODED VIEW PRN6000 Sealing and Soundproofing Contents Pages 64 BODY SEALS A Door pillar protective seal 64-1 B "D53 CABRIOLET" windscreen ... are no particular points concerning the removal of the inner section (1) PRN6600 66-2 66 D WINDOW SEALS Rear door frame seal 66 E Remove the trim and the small fixed window Remove: the seal, which ... 92258S Rear door frame slide channel Remove the window and the small fixed window H There are no particular points concerning the removal of the inner section (1) Remove the frame slide channel,...