Tài liệu hướng dẫn sửa chữa Nissan teana l33 esm tai lieu sua chua phan 1 . Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác, hiệu quả, hợp lý
DRIVER INFORMATION & MULTIMEDIA SECTION AV AUDIO, VISUAL & NAVIGATION SYSTEM A B C D E CONTENTS BASE AUDIO BASIC INSPECTION 25 PRECAUTION DIAGNOSIS AND REPAIR WORKFLOW 25 PRECAUTIONS Work Flow 25 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" Precaution Necessary for Steering Wheel Rotation After Battery Disconnect Precaution for Trouble Diagnosis Precaution for Harness Repair Precaution for Work DTC/CIRCUIT DIAGNOSIS 27 PREPARATION FRONT SPEAKER 30 POWER SUPPLY AND GROUND CIRCUIT 27 AUDIO UNIT .27 AUDIO UNIT : Diagnosis Procedure .27 SYSTEM DESCRIPTION 10 SYMPTOM DIAGNOSIS 34 COMPONENT PARTS .10 AUDIO SYSTEM 34 Component Parts Location 10 Component Description 10 Symptom Table .34 NORMAL OPERATING CONDITION 36 Exploded View 37 Removal and Installation 37 ECU DIAGNOSIS INFORMATION 16 FRONT SPEAKER 38 Removal and Installation 38 FRONT DOOR SPEAKER 39 Removal and Installation 39 STEERING SWITCH 40 Wiring Diagram 18 Revision: July 2014 L M REMOVAL AND INSTALLATION 37 AV Diagnosis Description 13 On Board Diagnosis Function 13 BASE AUDIO .18 K Description .36 AUDIO UNIT 37 WIRING DIAGRAM 18 J Diagnosis Procedure .32 DIAGNOSIS SYSTEM (AUDIO UNIT) 13 Reference Value 16 I Diagnosis Procedure .30 STEERING SWITCH 32 AUDIO UNIT .16 H Diagnosis Procedure .28 Special Service Tools Commercial Service Tools System Diagram 12 System Description 12 G FRONT DOOR SPEAKER 28 PREPARATION SYSTEM .12 F AV-1 Exploded View 40 Removal and Installation 40 2015 Model L33 O P ANTENNA AMP 41 Removal and Installation 41 ANTENNA FEEDER 42 Location of Antenna 42 Window Antenna Repair 42 DISPLAY AUDIO WITHOUT BOSE DTC/CIRCUIT DIAGNOSIS 77 POWER SUPPLY AND GROUND CIRCUIT 77 AUDIO UNIT 77 AUDIO UNIT : Diagnosis Procedure 77 FRONT DOOR SPEAKER 78 PRECAUTION 45 PRECAUTIONS 45 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 45 Precaution Necessary for Steering Wheel Rotation After Battery Disconnect 45 Precaution for Trouble Diagnosis 46 Precaution for Harness Repair 46 Precaution for Work 46 PREPARATION 47 Diagnosis Procedure 78 FRONT SPEAKER 80 Diagnosis Procedure 80 REAR DOOR SPEAKER 82 Diagnosis Procedure 82 REAR SPEAKER 84 Diagnosis Procedure 84 REAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 86 Diagnosis Procedure 86 PREPARATION 47 MICROPHONE SIGNAL CIRCUIT 88 Special Service Tools 47 Commercial Service Tools 47 Diagnosis Procedure 88 SYSTEM DESCRIPTION 48 STEERING SWITCH 90 Diagnosis Procedure 90 COMPONENT PARTS 48 USB CONNECTOR 92 Component Parts Location 48 Component Description 49 Diagnosis Procedure 92 AUXILIARY INPUT JACK 93 SYSTEM 50 Diagnosis Procedure 93 System Diagram 50 System Description 50 SYMPTOM DIAGNOSIS 94 DIAGNOSIS SYSTEM (AUDIO UNIT) 52 AUDIO SYSTEM 94 Description 52 On Board Diagnosis Function 52 Symptom Table 94 NORMAL OPERATING CONDITION 97 ECU DIAGNOSIS INFORMATION 58 Description 97 AUDIO UNIT 58 REMOVAL AND INSTALLATION 99 Reference Value 58 AUDIO UNIT 99 WIRING DIAGRAM 62 Exploded View 99 Removal and Installation 99 DISPLAY AUDIO WITHOUT BOSE 62 Wiring Diagram 62 BASIC INSPECTION 73 DIAGNOSIS AND REPAIR WORKFLOW 73 Work Flow 73 USB INTERFACE 100 Removal and Installation 100 AUX IN JACK 101 Removal and Installation 101 FRONT SPEAKER 102 INSPECTION AND ADJUSTMENT 75 Removal and Installation 102 REGISTRATION (AUDIO UNIT) 75 REGISTRATION (AUDIO UNIT) : Description 75 REGISTRATION (AUDIO UNIT) : Work Procedure 75 FRONT DOOR SPEAKER 103 Revision: July 2014 Removal and Installation 103 REAR DOOR SPEAKER 104 Removal and Installation 104 AV-2 2015 Model L33 REAR SPEAKER 105 DISPLAY AUDIO WITH BOSE 134 Removal and Installation 105 Wiring Diagram 134 STEERING SWITCH 106 BASIC INSPECTION 150 Exploded View 106 Removal and Installation 106 DIAGNOSIS AND REPAIR WORKFLOW 150 ANTENNA FEEDER 107 Location of Antenna 107 Window Antenna Repair 107 ANTENNA AMP 110 Removal and Installation 110 MICROPHONE 111 INSPECTION AND ADJUSTMENT 152 C REGISTRATION (AUDIO UNIT) 152 REGISTRATION (AUDIO UNIT) : Description 152 REGISTRATION (AUDIO UNIT) : Work Procedure 152 D DTC/CIRCUIT DIAGNOSIS 154 REAR VIEW CAMERA 112 POWER SUPPLY AND GROUND CIRCUIT 154 DISPLAY AUDIO WITH BOSE PRECAUTION 113 PRECAUTIONS 113 AUDIO UNIT 154 AUDIO UNIT : Diagnosis Procedure 154 BOSE SPEAKER AMP 154 BOSE SPEAKER AMP : Diagnosis Procedure 155 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 113 Precaution Necessary for Steering Wheel Rotation After Battery Disconnect 113 Precaution for Trouble Diagnosis 114 Precaution for Harness Repair 114 Precaution for Work 114 FRONT DOOR SPEAKER 156 PREPARATION 115 REAR DOOR SPEAKER 164 PREPARATION 115 Special Service Tools 115 Commercial Service Tools 115 SYSTEM DESCRIPTION 116 COMPONENT PARTS 116 Component Parts Location 116 Component Description 117 SYSTEM 118 System Diagram 118 System Description 119 DIAGNOSIS SYSTEM (AUDIO UNIT) 121 Description 121 On Board Diagnosis Function 121 Diagnosis Procedure 156 CENTER SPEAKER 162 G H I Diagnosis Procedure 162 J Diagnosis Procedure 164 REAR SPEAKER 167 Diagnosis Procedure 167 K AMP ON SIGNAL CIRCUIT 170 Diagnosis Procedure 170 REAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 171 Diagnosis Procedure 171 L M MICROPHONE SIGNAL CIRCUIT 176 Diagnosis Procedure 176 AV STEERING SWITCH 178 Diagnosis Procedure 178 O USB CONNECTOR 180 Diagnosis Procedure 180 AUXILIARY INPUT JACK 181 Diagnosis Procedure 181 SYMPTOM DIAGNOSIS 182 Reference Value 131 AUDIO SYSTEM 182 WIRING DIAGRAM 134 Symptom Table 182 Revision: July 2014 F Diagnosis Procedure 159 Reference Value 127 BOSE SPEAKER AMP 131 E FRONT SPEAKER 159 ECU DIAGNOSIS INFORMATION 127 AUDIO UNIT 127 B Work Flow 150 Removal and Installation 111 Removal and Installation 112 A AV-3 2015 Model L33 P NORMAL OPERATING CONDITION 187 Description .187 REMOVAL AND INSTALLATION 189 AUDIO UNIT 189 Cautions in Removing Battery Terminal and AV Control Unit (Models with AV Control Unit) 207 Precaution for Trouble Diagnosis 207 Precaution for Harness Repair 207 Precaution for Work 207 Exploded View .189 Removal and Installation .189 PREPARATION 209 USB INTERFACE 190 Removal and Installation .190 Special Service Tools 209 Commercial Service Tools 209 AUX IN JACK 191 SYSTEM DESCRIPTION 210 Removal and Installation .191 FRONT SPEAKER 192 PREPARATION 209 COMPONENT PARTS 210 Removal and Installation .192 Component Parts Location 210 Component Description 211 CENTER SPEAKER 193 SYSTEM 212 Removal and Installation .193 FRONT DOOR SPEAKER 194 System Diagram 212 System Description 212 Removal and Installation .194 DIAGNOSIS SYSTEM (AV CONTROL UNIT) 216 REAR DOOR SPEAKER 195 Description 216 On Board Diagnosis Function 216 CONSULT Function 217 Removal and Installation .195 REAR SPEAKER 196 Removal and Installation .196 BOSE SPEAKER AMP 197 Removal and Installation .197 STEERING SWITCH 198 Exploded View .198 Removal and Installation .198 ECU DIAGNOSIS INFORMATION 218 AV CONTROL UNIT 218 Reference Value 218 DTC Index 221 BOSE SPEAKER AMP 222 Reference Value 222 ANTENNA FEEDER 199 WIRING DIAGRAM 225 Location of Antenna .199 Window Antenna Repair 199 NAVIGATION WITH BOSE 225 ANTENNA AMP 202 BASIC INSPECTION 242 Removal and Installation .202 MICROPHONE 203 Removal and Installation .203 REAR VIEW CAMERA 204 Exploded View .204 Removal and Installation .204 ITS CONTROL UNIT 205 Removal and Installation .205 NAVIGATION WITH BOSE PRECAUTION 206 PRECAUTIONS 206 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 206 Precaution Necessary for Steering Wheel Rotation After Battery Disconnect 206 Revision: July 2014 Wiring Diagram 225 DIAGNOSIS AND REPAIR WORKFLOW 242 Work Flow 242 INSPECTION AND ADJUSTMENT 244 ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT 244 ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT : Description 244 ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT : Work Procedure 244 CONFIGURATION (AV CONTROL UNIT) 244 CONFIGURATION (AV CONTROL UNIT) : Description 245 CONFIGURATION (AV CONTROL UNIT) : Work Procedure 245 CONFIGURATION (AV CONTROL UNIT) : Configuration List 246 AV-4 2015 Model L33 DTC/CIRCUIT DIAGNOSIS 247 U1000 CAN COMM CIRCUIT 247 DTC Logic 264 Diagnosis Procedure 264 DTC Logic 247 Diagnosis Procedure 247 U1310 AV CONTROL UNIT 266 U1010 CONTROL UNIT (CAN) 248 POWER SUPPLY AND GROUND CIRCUIT 267 DTC Logic 248 U1217 AV CONTROL UNIT 249 DTC Logic 249 DTC Logic 266 AV CONTROL UNIT 267 AV CONTROL UNIT : Diagnosis Procedure 267 U1229 AV CONTROL UNIT 250 BOSE SPEAKER AMP 267 BOSE SPEAKER AMP : Diagnosis Procedure 267 DTC Logic 250 FRONT DOOR SPEAKER 269 U122F AV CONTROL UNIT 251 Diagnosis Procedure 269 DTC Logic 251 FRONT SPEAKER 272 U1244 GPS ANTENNA 252 Diagnosis Procedure 272 DTC Logic 252 Diagnosis Procedure 252 CENTER SPEAKER 275 U1263 USB 253 DTC Logic 253 Diagnosis Procedure 253 U1264 ANTENNA AMP 254 DTC Logic 254 Diagnosis Procedure 254 REAR DOOR SPEAKER 277 Diagnosis Procedure 277 REAR SPEAKER 280 Diagnosis Procedure 280 Diagnosis Procedure 283 REAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 284 U12AA CONFIGURATION ERROR 256 Diagnosis Procedure 284 DTC Logic 256 Diagnosis Procedure 256 MICROPHONE SIGNAL CIRCUIT 289 U12AB ANTENNA 257 STEERING SWITCH 291 DTC Logic 258 U12AD AV CONTROL UNIT 259 DTC Logic 259 U12AE AV CONTROL UNIT 260 DTC Logic 260 Diagnosis Procedure 289 Diagnosis Procedure 291 USB CONNECTOR 293 AUXILIARY INPUT JACK 294 G H I J K L M MULTI AV SYSTEM 295 Symptom Table 295 O NORMAL OPERATING CONDITION 300 Description 300 REMOVAL AND INSTALLATION 309 U12B1 POWER SUPPLY VOLTAGE 263 Exploded View 309 Removal and Installation 309 Revision: July 2014 F SYMPTOM DIAGNOSIS 295 AV DTC Logic 262 Diagnosis Procedure 262 U1300 AV COMM CIRCUIT 264 E Diagnosis Procedure 294 U12B0 POWER SUPPLY VOLTAGE 262 DTC Logic 263 Diagnosis Procedure 263 D Diagnosis Procedure 293 U12AF AV CONTROL UNIT 261 DTC Logic 261 C AMP ON SIGNAL CIRCUIT 283 DTC Logic 255 Diagnosis Procedure 255 U12AC AV CONTROL UNIT 258 B Diagnosis Procedure 275 U1265 BOSE AMP 255 DTC Logic 257 Diagnosis Procedure 257 A AV CONTROL UNIT 309 USB INTERFACE 310 AV-5 Removal and Installation 310 2015 Model L33 P AUX IN JACK 311 STEERING SWITCH 319 Removal and Installation .311 Exploded View 319 Removal and Installation 319 FRONT SPEAKER 312 Removal and Installation .312 ANTENNA FEEDER 320 CENTER SPEAKER 313 Location of Antenna 320 Window Antenna Repair 320 Removal and Installation .313 FRONT DOOR SPEAKER 314 Removal and Installation .314 REAR DOOR SPEAKER 315 Removal and Installation .315 REAR SPEAKER 316 ANTENNA AMP 323 Removal and Installation 323 MICROPHONE 324 Removal and Installation 324 REAR VIEW CAMERA 325 Removal and Installation .316 Exploded View 325 Removal and Installation 325 BOSE SPEAKER AMP 317 ITS CONTROL UNIT 326 Removal and Installation .317 Removal and Installation 326 GPS ANTENNA 318 Removal and Installation .318 Revision: July 2014 AV-6 2015 Model L33 PRECAUTIONS [BASE AUDIO] < PRECAUTION > PRECAUTION A PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" B INFOID:0000000010509468 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision Information necessary to service the system safely is included in the SR and SB section of this Service Manual WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module, see the SR section • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery and wait at least three minutes before performing any service Precaution Necessary for Steering Wheel Rotation After Battery Disconnect INFOID:0000000010509469 NOTE: • Before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables • Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing work If a DTC is detected, perform trouble diagnosis according to self-diagnosis results This vehicle is equipped with a push-button ignition switch and a steering lock unit If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure below before starting the repair operation OPERATION PROCEDURE D E F G H I J K L M AV Connect both battery cables NOTE: Supply power using jumper cables if battery is discharged Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position (At this time, the steering lock will be released.) Disconnect both battery cables The steering lock will remain released with both battery cables disconnected and the steering wheel can be turned Perform the necessary repair operation When the repair work is completed, re-connect both battery cables With the brake pedal released, turn the push-button ignition switch from ACC position to ON position, then to LOCK position (The steering wheel will lock when the push-button ignition switch is turned to LOCK position.) Perform self-diagnosis check of all control units using CONSULT Revision: July 2014 C AV-7 2015 Model L33 O P PRECAUTIONS [BASE AUDIO] < PRECAUTION > Precaution for Trouble Diagnosis INFOID:0000000010509470 AV COMMUNICATION SYSTEM • Do not apply voltage of 7.0 V or higher to the measurement terminals • Use the tester with its open terminal voltage being 7.0 V or less • Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before checking the circuit Precaution for Harness Repair INFOID:0000000010509471 AV COMMUNICATION SYSTEM • Solder the repaired parts, and wrap with tape [Frays of twisted line must be within 110 mm (4.33 in).] PKIA0306E • Do not perform bypass wire connections for the repair parts (The spliced wire will become separated and the characteristics of twisted line will be lost.) PKIA0307E Precaution for Work INFOID:0000000010509472 • When removing or disassembling each component, be careful not to damage or deform it If a component may be subject to interference, be sure to protect it with a shop cloth • When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it • Protect the removed parts with a shop cloth and prevent them from being dropped • Replace a deformed or damaged clip • If a part is specified as a non-reusable part, always replace it with a new one • Be sure to tighten bolts and nuts securely to the specified torque • After installation is complete, be sure to check that each part works properly • Follow the steps below to clean components: - Water soluble dirt: • Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area • Then rub with a soft, dry cloth - Oily dirt: • Dip a soft cloth into lukewarm water with mild detergent (concentration: within to 3%) and wipe the dirty area • Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off • Then rub with a soft, dry cloth - Do not use organic solvent such as thinner, benzene, alcohol or gasoline - For genuine leather seats, use a genuine leather seat cleaner Revision: July 2014 AV-8 2015 Model L33 PREPARATION [BASE AUDIO] < PREPARATION > PREPARATION A PREPARATION Special Service Tools INFOID:0000000010509473 B The actual shape of the tools may differ from those illustrated here Tool number (TechMate No.) Tool name Description — (J-46534) Trim Tool Set Removing trim components C D E AWJIA0483ZZ F Commercial Service Tools INFOID:0000000010509474 G Tool name Description Power tool Loosening nuts, screws and bolts H I PIIB1407E J K L M AV O P Revision: July 2014 AV-9 2015 Model L33 COMPONENT PARTS [BASE AUDIO] < SYSTEM DESCRIPTION > SYSTEM DESCRIPTION COMPONENT PARTS Component Parts Location INFOID:0000000010509475 AWNIA3677ZZ Front speaker LH Steering switches Audio unit Front speaker RH Front door speaker LH Front door speaker RH Antenna amp Window antenna Component Description INFOID:0000000010509476 Part name Audio unit Revision: July 2014 Description • Controls audio and AUX IN connection functions • Display unit is built in to audio unit AV-10 2015 Model L33 INTELLIGENT KEY WARNING BUZZER < REMOVAL AND INSTALLATION > INTELLIGENT KEY WARNING BUZZER A Removal and Installation INFOID:0000000010510775 REMOVAL B NOTE: The Intelligent Key warning buzzer is located in the left front area of the engine compartment Remove the Intelligent Key warning buzzer harness clip Remove the nut (B) that retains the Intelligent Key warning buzzer (1) to the body Disconnect the harness connector (A) from the Intelligent Key warning buzzer (1) and remove C D E F ALKIA2728ZZ INSTALLATION G Installation is in the reverse order of removal H I J DLK L M N O P Revision: July 2014 DLK-223 2015 Model L33 REMOTE KEYLESS ENTRY RECEIVER < REMOVAL AND INSTALLATION > REMOTE KEYLESS ENTRY RECEIVER Removal and Installation INFOID:0000000010510776 REMOVAL Remove glove box assembly Refer to IP-23, "Removal and Installation" Disconnect the harness connector (A) from the remote keyless entry receiver (1) Remove the screw (B) and the remote keyless entry receiver (1) ALKIA2725ZZ INSTALLATION Installation is in the reverse order or removal Revision: July 2014 DLK-224 2015 Model L33 INTELLIGENT KEY BATTERY < REMOVAL AND INSTALLATION > INTELLIGENT KEY BATTERY A Removal and Installation INFOID:0000000010510777 Release the lock knob on the back of the Intelligent Key and remove the key Insert a suitable tool (A) wrapped with a cloth into the slit of the corner and twist it to separate the upper part from the lower part CAUTION: • Do not touch the circuit board or battery terminal • The key fob is water-resistant However, if it does get wet, immediately wipe it dry B C D E PIIB6221E Replace the battery with a new one Battery replacement F :Coin-type lithium battery (CR2032) G Align the tips of the upper and lower parts, and then push them together until unit is securely closed CAUTION: • When replacing battery, keep dirt, grease, and other foreign materials off the electrode contact area • After replacing the battery, check that all Intelligent Key functions work normally H I J PIIB6222E DLK L M N O P Revision: July 2014 DLK-225 2015 Model L33 TRUNK LID OPENER CANCEL SWITCH < REMOVAL AND INSTALLATION > TRUNK LID OPENER CANCEL SWITCH Removal and Installation INFOID:0000000010510778 REMOVAL Remove the glove box assembly Refer to IP-23, "Removal and Installation" Release pawls and remove the trunk lid opener cancel switch INSTALLATION Installation is in the reverse order of removal Revision: July 2014 DLK-226 2015 Model L33 TRUNK LID OPENER SWITCH < REMOVAL AND INSTALLATION > TRUNK LID OPENER SWITCH A Removal and Installation INFOID:0000000010510779 REMOVAL B Remove the instrument lower panel LH Refer to IP-22, "Removal and Installation" Remove screws (A) that retain the upper switch carrier (1) to the instrument lower panel LH (2) C D E ALKIA2729ZZ Using a suitable tool release pawls and remove the trunk lid opener switch from the upper switch carrier (1) Pawl: F G H I AWOIA0091ZZ INSTALLATION J Installation is in the reverse order of removal DLK L M N O P Revision: July 2014 DLK-227 2015 Model L33 TRUNK OPENER REQUEST SWITCH < REMOVAL AND INSTALLATION > TRUNK OPENER REQUEST SWITCH Removal and Installation INFOID:0000000010510780 REMOVAL Remove the license plate lamp finisher Refer to EXT-37, "Removal and Installation" Release the pawls and remove the trunk opener request switch (1) : Pawl ALKIA2722ZZ INSTALLATION Installation is in the reverse order of removal Revision: July 2014 DLK-228 2015 Model L33 FRONT DOOR < UNIT DISASSEMBLY AND ASSEMBLY > UNIT DISASSEMBLY AND ASSEMBLY A FRONT DOOR Exploded View INFOID:0000000010510781 B C D E F G H I ALKIA2685ZZ Front door panel Front door outside molding Front door outer panel Front door tape Front door sash molding Front door check link Front door inside seal Front door lower seal Front door vapor barrier 10 Front door weatherstrip 11 Front door grommet Disassembly and Assembly INFOID:0000000010510782 NOTE: RH side shown; LH similar Remove front door Refer to DLK-184, "DOOR ASSEMBLY : Removal and Installation" Remove front door speaker Refer to AV-37, "Removal and Installation" (BASE AUDIO) or AV-103, "Removal and Installation" (DISPLAY AUDIO WITHOUT BOSE) or AV-194, "Removal and Installation" (DISPLAY AUDIO WITH BOSE) or AV-314, "Removal and Installation" (NAVIGATION WITH BOSE) Remove front door lower seal Remove front door bumper rubber Remove front door sash molding Refer to EXT-32, "FRONT DOOR SASH MOLDING : Removal and Installation" Remove front door weatherstrip Remove front door glass Refer to GW-14, "Removal and Installation" Remove front door glass regulator Refer to GW-16, "Removal and Installation" Remove front door glass rubber run Refer to GW-16, "Exploded View" 10 Remove front door outside molding Refer to EXT-35, "Removal and Installation" 11 Remove front door front and rear glass channel Refer to GW-16, "Exploded View" DLK-229 DLK 12 Front door bumper rubber DISASSEMBLY Revision: July 2014 J 2015 Model L33 L M N O P FRONT DOOR < UNIT DISASSEMBLY AND ASSEMBLY > 12 Remove front door lock assembly Refer to DLK-203, "FRONT DOOR LOCK : Removal and Installation" 13 Remove front door check link ASSEMBLY Assembly is in the reverse order of disassembly Revision: July 2014 DLK-230 2015 Model L33 REAR DOOR < UNIT DISASSEMBLY AND ASSEMBLY > REAR DOOR A Exploded View INFOID:0000000010510783 B C D E F G H I ALKIA2686ZZ Rear door outer panel Rear door sash molding Rear door tape Rear door outside molding Rear door check link Rear door weatherstrip Rear door lower seal Rear door vapor barrier Rear door inside seal 10 Rear door grommet 11 Rear door bumper rubber Disassembly and Assembly J DLK 12 Rear door panel INFOID:0000000010510784 L DISASSEMBLY NOTE: RH side shown; LH similar Remove rear door Refer to DLK-190, "DOOR ASSEMBLY : Removal and Installation" Remove rear door finisher Refer to INT-19, "Removal and Installation" Remove rear door speaker (if equipped) Refer to AV-195, "Removal and Installation" (DISPLAY AUDIO WITH BOSE) or AV-315, "Removal and Installation" (NAVIGATION WITH BOSE) Remove rear door lower seal Remove rear door bumper rubber Remove rear door sash molding Refer to EXT-32, "FRONT DOOR SASH MOLDING : Removal and Installation" Remove rear door weatherstrip Remove rear door glass Refer to GW-20, "Removal and Installation" Remove rear door glass regulator Refer to GW-21, "Removal and Installation" 10 Remove rear door outside molding Refer to EXT-35, "Removal and Installation" 11 Remove rear door lock Refer to DLK-204, "REAR DOOR LOCK : Removal and Installation" 12 Remove rear door check link ASSEMBLY Revision: July 2014 DLK-231 2015 Model L33 M N O P REAR DOOR < UNIT DISASSEMBLY AND ASSEMBLY > Assembly is in the reverse order of disassembly Revision: July 2014 DLK-232 2015 Model L33 ENGINE SECTION ACC ACCELERATOR CONTROL SYSTEM A ACC C D E CONTENTS PRECAUTION ACCELERATOR CONTROL SYSTEM PRECAUTIONS Exploded View Removal and Installation Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" Precaution Necessary for Steering Wheel Rotation After Battery Disconnect REMOVAL AND INSTALLATION SERVICE DATA AND SPECIFICATIONS (SDS) SERVICE DATA AND SPECIFICATIONS (SDS) Accelerator Control F G H I J K L M N O P Revision: July 2014 ACC-1 2015 Model L33 PRECAUTIONS < PRECAUTION > PRECAUTION PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000010532570 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision Information necessary to service the system safely is included in the SR and SB section of this Service Manual WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module, see the SR section • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery and wait at least three minutes before performing any service Precaution Necessary for Steering Wheel Rotation After Battery Disconnect INFOID:0000000010532571 NOTE: • Before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables • Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing work If a DTC is detected, perform trouble diagnosis according to self-diagnosis results This vehicle is equipped with a push-button ignition switch and a steering lock unit If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure below before starting the repair operation OPERATION PROCEDURE Connect both battery cables NOTE: Supply power using jumper cables if battery is discharged Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position (At this time, the steering lock will be released.) Disconnect both battery cables The steering lock will remain released with both battery cables disconnected and the steering wheel can be turned Perform the necessary repair operation When the repair work is completed, re-connect both battery cables With the brake pedal released, turn the push-button ignition switch from ACC position to ON position, then to LOCK position (The steering wheel will lock when the push-button ignition switch is turned to LOCK position.) Perform self-diagnosis check of all control units using CONSULT Revision: July 2014 ACC-2 2015 Model L33 ACCELERATOR CONTROL SYSTEM < REMOVAL AND INSTALLATION > REMOVAL AND INSTALLATION A ACCELERATOR CONTROL SYSTEM Exploded View INFOID:0000000010532572 ACC C D E F G H I J K AWBIA1396ZZ Accelerator pedal assembly L Front Removal and Installation INFOID:0000000010532573 M REMOVAL Disconnect the harness connector from accelerator pedal assembly Remove the two accelerator pedal bolts Remove the accelerator pedal assembly CAUTION: • Do not disassemble the accelerator pedal assembly • Do not drop or impact the accelerator pedal assembly • Do not expose the accelerator pedal assembly to water N O INSTALLATION P Installation is in the reverse order of removal Revision: July 2014 ACC-3 2015 Model L33 ACCELERATOR CONTROL SYSTEM < REMOVAL AND INSTALLATION > • Check the accelerator pedal moves smooth within the specified range Accelerator pedal stroke (A) : Refer to ACC-5, "Accelerator Control" ALBIA0168GB CAUTION: • Whenever the harness connector of the accelerator pedal position sensor is disconnected, perform the “Accelerator pedal released position learning” Refer to EC-166, "Work Procedure" [QR25DE (TYPE 1)], EC-646, "Work Procedure" [QR25DE (TYPE 2)], EC-1018, "Work Procedure" [VQ35DE (TYPE 1)], or EC-1468, "Work Procedure" [VQ35DE (TYPE 2)] • The accelerator pedal should return smoothly to the fully raised position Revision: July 2014 ACC-4 2015 Model L33 SERVICE DATA AND SPECIFICATIONS (SDS) < SERVICE DATA AND SPECIFICATIONS (SDS) SERVICE DATA AND SPECIFICATIONS (SDS) A SERVICE DATA AND SPECIFICATIONS (SDS) Accelerator Control INFOID:0000000010532574 ACC Unit: mm (in) C D E F ALBIA0168GB Accelerator pedal stroke (A) 50.5 - 53.5 (1.99 - 2.11) G H I J K L M N O P Revision: July 2014 ACC-5 2015 Model L33