Nissan teana l33 esm tai lieu sua chua phan 5

Tài liệu hướng dẫn sửa chữa xe Nissan teana l33 esm tai lieu sua chua phan 5 . Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác, hiệu quả, hợp lý

TRANSMISSION & DRIVELINE SECTION TM TRANSAXLE & TRANSMISSION A B C TM E CONTENTS CVT: RE0F10D CVT CONTROL SYSTEM : Output Speed Sensor 18 CVT CONTROL SYSTEM : Input Speed Sensor 18 CVT CONTROL SYSTEM : CVT Fluid Temperature Sensor 18 CVT CONTROL SYSTEM : Primary Pressure Sensor .19 CVT CONTROL SYSTEM : Secondary Pressure Sensor .19 CVT CONTROL SYSTEM : Primary Pressure Solenoid Valve .20 CVT CONTROL SYSTEM : Secondary Pressure Solenoid Valve 20 CVT CONTROL SYSTEM : Select Solenoid Valve 20 CVT CONTROL SYSTEM : Torque Converter Clutch Solenoid Valve .20 CVT CONTROL SYSTEM : Line Pressure Solenoid Valve 21 CVT CONTROL SYSTEM : Sport Mode Switch 21 CVT CONTROL SYSTEM : SPORT Indicator Lamp 21 CVT CONTROL SYSTEM : O/D OFF Indicator Lamp 21 CVT CONTROL SYSTEM : Shift Position Indicator 22 HOW TO USE THIS MANUAL HOW TO USE THIS SECTION Information PRECAUTION 10 PRECAUTIONS 10 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 10 Precautions Necessary for Steering Wheel Rotation after Battery Disconnect 10 Precaution for Procedure without Cowl Top Cover 11 Precaution for TCM and Transaxle Assembly Replacement 11 General Precautions 11 On Board Diagnosis (OBD) System of CVT and Engine 12 Removal and Installation Procedure for CVT Unit Connector 12 PREPARATION 14 PREPARATION 14 Special Service Tools 14 Commercial Service Tools 14 SYSTEM DESCRIPTION 15 COMPONENT PARTS .15 CVT CONTROL SYSTEM 15 CVT CONTROL SYSTEM : Component Parts Location 15 CVT CONTROL SYSTEM : TCM 17 CVT CONTROL SYSTEM : Transmission Range Switch 17 CVT CONTROL SYSTEM : Primary Speed Sensor 17 Revision: July 2014 F G H I J K L M SHIFT LOCK SYSTEM 22 SHIFT LOCK SYSTEM : Component Parts Location 22 N STRUCTURE AND OPERATION 23 O TRANSAXLE 23 TRANSAXLE : Cross-Sectional View 23 TRANSAXLE : Operation Status .24 TRANSAXLE : Transaxle Mechanism .24 TRANSAXLE : Oil Pressure System .27 TRANSAXLE : Component Description 28 FLUID COOLER & FLUID WARMER SYSTEM 28 FLUID COOLER & FLUID WARMER SYSTEM : System Description 29 TM-1 2015 Model L33 P SHIFT LOCK SYSTEM 30 SHIFT LOCK SYSTEM : System Description 30 KEY LOCK SYSTEM 31 KEY LOCK SYSTEM : System Description 31 SYSTEM 32 CVT CONTROL SYSTEM 32 CVT CONTROL SYSTEM : System Description 32 CVT CONTROL SYSTEM : Fail-safe 33 CVT CONTROL SYSTEM : Protection Control 36 LINE PRESSURE CONTROL 37 LINE PRESSURE CONTROL : System Description 37 SHIFT CONTROL 37 SHIFT CONTROL : System Description 38 SELECT CONTROL 39 SELECT CONTROL : System Description 40 LOCK-UP CONTROL 40 LOCK-UP CONTROL : System Description 40 ON BOARD DIAGNOSTIC (OBD) SYSTEM 42 Description 42 Function of OBD 42 DIAGNOSIS SYSTEM (TCM) 43 DIAGNOSIS DESCRIPTION 43 DIAGNOSIS DESCRIPTION : Trip Detection Diagnosis and Trip Detection Diagnosis 43 DIAGNOSIS DESCRIPTION : DTC and DTC of 1st Trip 43 DIAGNOSIS DESCRIPTION : Malfunction Indicator Lamp (MIL) 43 DIAGNOSIS DESCRIPTION : Counter System 43 CONSULT Function 45 ECU DIAGNOSIS INFORMATION 51 TCM 51 Question sheet 79 ADDITIONAL SERVICE WHEN REPLACING TCM 81 Description 81 Work Procedure 81 ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY 83 Description 83 Work Procedure 83 ADDITIONAL SERVICE WHEN REPLACING TCM AND TRANSAXLE ASSEMBLY 85 Description 85 Work Procedure 85 CVT FLUID 87 Replacement 87 Adjustment 88 STALL TEST 90 Work Procedure 90 CVT POSITION 91 Inspection 91 Adjustment 91 DTC/CIRCUIT DIAGNOSIS 92 U0073 COMMUNICATION BUS A OFF 92 DTC Logic 92 Diagnosis Procedure 92 U0100 LOST COMMUNICATION (ECM A) 93 DTC Logic 93 Diagnosis Procedure 93 U0140 LOST COMMUNICATION (BCM) 94 DTC Logic 94 Diagnosis Procedure 94 U0141 LOST COMMUNICATION (BCM A) 95 DTC Logic 95 Diagnosis Procedure 95 Reference Value 51 Fail-safe 57 Protection Control 60 DTC Inspection Priority Chart 61 DTC Index 62 U0155 LOST COMMUNICATION (IPC) 96 WIRING DIAGRAM 64 U0300 CAN COMMUNICATION DATA 97 CVT CONTROL SYSTEM 64 Wiring diagram 64 CVT SHIFT LOCK SYSTEM 74 Wiring diagram 74 BASIC INSPECTION 78 DIAGNOSIS AND REPAIR WORK FLOW 78 Flowchart of Trouble Diagnosis 78 Revision: July 2014 DTC Logic 96 Diagnosis Procedure 96 DTC Logic 97 Diagnosis Procedure 97 U1000 CAN COMM CIRCUIT 98 Description 98 DTC Logic 98 Diagnosis Procedure 98 U1117 LOST COMMUNICATION (ABS) 99 DTC Logic 99 Diagnosis Procedure 99 TM-2 2015 Model L33 P062F EEPROM 100 Description 100 DTC Logic 100 Diagnosis Procedure 100 DTC Logic 136 Diagnosis Procedure 136 A P0779 PRESSURE CONTROL SOLENOID B 138 P0705 TRANSMISSION RANGE SENSOR A 101 DTC Logic 138 Diagnosis Procedure 138 B DTC Logic 101 Diagnosis Procedure 101 Component Inspection 105 P0841 TRANSMISSION FLUID PRESSURE SEN/SW A 140 C DTC Logic 140 Diagnosis Procedure 140 P0706 TRANSMISSION RANGE SENSOR A 107 DTC Logic 107 Diagnosis Procedure 107 Component Inspection 109 TM P0847 TRANSMISSION FLUID PRESSURE SEN/SW B 141 P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A 110 E DTC Logic 110 Diagnosis Procedure 113 Component Inspection 114 P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A 116 DTC Logic 116 Diagnosis Procedure 116 Component Inspection 116 P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A 118 DTC Logic 118 Diagnosis Procedure 118 Component Inspection 119 DTC Logic 141 Diagnosis Procedure 141 P0848 TRANSMISSION FLUID PRESSURE SEN/SW B 143 DTC Logic 143 Diagnosis Procedure 143 P084C TRANSMISSION FLUID PRESSURE SEN/SW H 145 DTC Logic 145 Diagnosis Procedure 145 P084D TRANSMISSION FLUID PRESSURE SEN/SW H 147 P0863 TCM COMMUNICATION 149 J DTC Logic 149 Diagnosis Procedure 149 P0890 TCM 150 P0962 PRESSURE CONTROL SOLENOID A 151 DTC Logic 151 Diagnosis Procedure 151 DTC Logic 153 Diagnosis Procedure 153 DTC Logic 155 Diagnosis Procedure 156 DTC Logic 157 Diagnosis Procedure 157 P0967 PRESSURE CONTROL SOLENOID B 159 DTC Logic 159 Diagnosis Procedure 159 P0776 PRESSURE CONTROL SOLENOID B 134 DTC Logic 134 Diagnosis Procedure 135 P2765 INPUT SPEED SENSOR B 161 P0778 PRESSURE CONTROL SOLENOID B 136 Revision: July 2014 N O P0966 PRESSURE CONTROL SOLENOID B 157 P0746 PRESSURE CONTROL SOLENOID A 132 DTC Logic 132 Diagnosis Procedure 133 M P0965 PRESSURE CONTROL SOLENOID B 155 P0744 TORQUE CONVERTER 130 DTC Logic 130 Diagnosis Procedure 131 L P0963 PRESSURE CONTROL SOLENOID A 153 P0743 TORQUE CONVERTER 128 DTC Logic 128 Diagnosis Procedure 129 K DTC Logic 150 Diagnosis Procedure 150 P0740 TORQUE CONVERTER 126 DTC Logic 126 Diagnosis Procedure 127 H I P0717 INPUT SPEED SENSOR A 123 DTC Logic 123 Diagnosis Procedure 124 G DTC Logic 147 Diagnosis Procedure 147 P0715 INPUT SPEED SENSOR A 120 DTC Logic 120 Diagnosis Procedure 121 F TM-3 DTC Logic 161 2015 Model L33 P Diagnosis Procedure .162 P2813 SELECT SOLENOID 164 Removal and Installation 188 Adjustment 189 DTC Logic 164 Diagnosis Procedure .165 AIR BREATHER HOSE 190 P2814 SELECT SOLENOID 166 CONTROL VALVE 191 DTC Logic 166 Diagnosis Procedure .166 Exploded View 191 Removal and Installation 192 Inspection 196 P2815 SELECT SOLENOID 168 DTC Logic 168 Diagnosis Procedure .168 MAIN POWER SUPPLY AND GROUND CIRCUIT 170 Diagnosis Procedure .170 SPORT MODE SWITCH 172 Component Function Check 172 Diagnosis Procedure .172 Component Inspection 173 SPORT INDICATOR CIRCUIT 174 Component Function Check 174 Diagnosis Procedure .174 SHIFT POSITION INDICATOR CIRCUIT 175 Removal and Installation 190 INPUT SPEED SENSOR 197 Exploded View 197 Removal and Installation 197 Inspection and Adjustment 197 PRIMARY SPEED SENSOR 199 Exploded View 199 Removal and Installation 199 Inspection and Adjustment 199 OUTPUT SPEED SENSOR 201 Exploded View 201 Removal and Installation 201 Inspection and Adjustment 201 DIFFERENTIAL SIDE OIL SEAL 202 Component Parts Function Inspection 175 Diagnosis Procedure .175 Exploded View 202 Removal and Installation 202 Inspection and Adjustment 203 SHIFT LOCK SYSTEM 176 CVT OIL WARMER SYSTEM 204 Component Function Check 176 Diagnosis Procedure .176 Component Inspection (Shift Lock Solenoid) 177 Component Inspection (Park Position Switch) 177 Component Inspection (Stop Lamp Switch) 178 SYMPTOM DIAGNOSIS 179 CVT CONTROL SYSTEM 179 Symptom Table .179 PERIODIC MAINTENANCE 183 CVT FLUID 183 Inspection 183 REMOVAL AND INSTALLATION 184 CVT SHIFT SELECTOR 184 Exploded View .184 Removal and Installation .184 Inspection 185 CONTROL CABLE 186 Exploded View .186 Removal and Installation .186 Inspection and Adjustment 187 TCM 188 Exploded View .188 Revision: July 2014 WATER HOSE 204 WATER HOSE : Exploded View 204 WATER HOSE : Removal and Installation 204 WATER HOSE : Inspection 206 CVT FLUID COOLER HOSE 206 CVT FLUID COOLER HOSE : Exploded View 206 CVT FLUID COOLER HOSE : Removal and Installation 207 CVT FLUID COOLER HOSE : Inspection 208 CVT OIL WARMER 208 CVT OIL WARMER : Exploded View 208 CVT OIL WARMER : Removal and Installation 208 CVT OIL WARMER : Inspection 209 CVT FLUID COOLER 210 Exploded View (GCC, MEX, LAC) 210 Removal and Installation (GCC, MEX, LAC) 210 PLUG 211 Description 211 Exploded View 211 Removal and Installation 211 Inspection and Adjustment 211 UNIT REMOVAL AND INSTALLATION 212 TRANSMISSION ASSEMBLY 212 TM-4 2015 Model L33 Exploded View 212 Removal and Installation 212 Inspection and Adjustment 214 CVT CONTROL SYSTEM : Input Speed Sensor 227 CVT CONTROL SYSTEM : CVT Fluid Temperature Sensor 227 CVT CONTROL SYSTEM : Primary Pressure Sensor 228 CVT CONTROL SYSTEM : Secondary Pressure Sensor 228 CVT CONTROL SYSTEM : Primary Pressure Solenoid Valve 229 CVT CONTROL SYSTEM : Secondary Pressure Solenoid Valve 229 CVT CONTROL SYSTEM : Select Solenoid Valve 229 CVT CONTROL SYSTEM : Torque Converter Clutch Solenoid Valve 229 CVT CONTROL SYSTEM : Line Pressure Solenoid Valve 230 CVT CONTROL SYSTEM : Paddle Shifter 230 CVT CONTROL SYSTEM : Shift Position Indicator 230 UNIT DISASSEMBLY AND ASSEMBLY 215 TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL 215 Exploded View 215 Disassembly 215 Assembly 215 Inspection 216 SERVICE DATA AND SPECIFICATIONS (SDS) 218 SERVICE DATA AND SPECIFICATIONS (SDS) 218 General Specification 218 Shift Characteristics 218 Stall Speed 218 Torque Converter 218 Heater Thermostat 218 A B C TM E F G CVT: RE0F10E SHIFT LOCK SYSTEM 230 SHIFT LOCK SYSTEM : Component Parts Location 230 PRECAUTION 219 STRUCTURE AND OPERATION 232 H PRECAUTIONS 219 TRANSAXLE 232 TRANSAXLE : Cross-Sectional View 232 TRANSAXLE : Operation Status 233 TRANSAXLE : Transaxle Mechanism 233 TRANSAXLE : Oil Pressure System 235 TRANSAXLE : Component Description 236 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 219 Precautions Necessary for Steering Wheel Rotation after Battery Disconnect 219 Precaution for Procedure without Cowl Top Cover 220 Precaution for TCM and Transaxle Assembly Replacement 220 General Precautions 220 On Board Diagnosis (OBD) System of CVT and Engine 221 Removal and Installation Procedure for CVT Unit Connector 221 PREPARATION 223 PREPARATION 223 Special Service Tools 223 Commercial Service Tools 223 SYSTEM DESCRIPTION 224 COMPONENT PARTS 224 CVT CONTROL SYSTEM 224 CVT CONTROL SYSTEM : Component Parts Location 224 CVT CONTROL SYSTEM : TCM 226 CVT CONTROL SYSTEM : Transmission Range Switch 226 CVT CONTROL SYSTEM : Primary Speed Sensor 226 CVT CONTROL SYSTEM : Output Speed Sensor 226 Revision: July 2014 FLUID COOLER & FLUID WARMER SYSTEM 236 FLUID COOLER & FLUID WARMER SYSTEM : System Description 237 SHIFT LOCK SYSTEM 238 SHIFT LOCK SYSTEM : System Description 238 KEY LOCK SYSTEM 239 KEY LOCK SYSTEM : System Description 239 I J K L M SYSTEM 240 CVT CONTROL SYSTEM 240 CVT CONTROL SYSTEM : System Description 240 CVT CONTROL SYSTEM : Fail-safe 241 CVT CONTROL SYSTEM : Protection Control 244 LINE PRESSURE CONTROL 245 LINE PRESSURE CONTROL : System Description 245 SHIFT CONTROL 245 SHIFT CONTROL : System Description 246 SELECT CONTROL 247 SELECT CONTROL : System Description 247 LOCK-UP CONTROL 248 LOCK-UP CONTROL : System Description 248 TM-5 2015 Model L33 N O P ON BOARD DIAGNOSTIC (OBD) SYSTEM 250 Description .250 Function of OBD 250 DIAGNOSIS SYSTEM (TCM) 251 DIAGNOSIS DESCRIPTION 251 DIAGNOSIS DESCRIPTION : Trip Detection Diagnosis and Trip Detection Diagnosis 251 DIAGNOSIS DESCRIPTION : DTC and DTC of 1st Trip 251 DIAGNOSIS DESCRIPTION : Malfunction Indicator Lamp (MIL) .251 DIAGNOSIS DESCRIPTION : Counter System 251 CONSULT Function .253 ECU DIAGNOSIS INFORMATION 259 TCM 259 Reference Value 259 Fail-safe 266 Protection Control 269 DTC Inspection Priority Chart 270 DTC Index .271 WIRING DIAGRAM 273 Inspection 300 Adjustment 300 DTC/CIRCUIT DIAGNOSIS 301 U0073 COMMUNICATION BUS A OFF 301 DTC Logic 301 Diagnosis Procedure 301 U0100 LOST COMMUNICATION (ECM A) 302 DTC Logic 302 Diagnosis Procedure 302 U0140 LOST COMMUNICATION (BCM) 303 DTC Logic 303 Diagnosis Procedure 303 U0141 LOST COMMUNICATION (BCM A) 304 DTC Logic 304 Diagnosis Procedure 304 U0155 LOST COMMUNICATION (IPC) 305 DTC Logic 305 Diagnosis Procedure 305 U0300 CAN COMMUNICATION DATA 306 CVT CONTROL SYSTEM 273 DTC Logic 306 Diagnosis Procedure 306 Wiring diagram 273 U1000 CAN COMM CIRCUIT 307 CVT SHIFT LOCK SYSTEM 283 Description 307 DTC Logic 307 Diagnosis Procedure 307 Wiring diagram 283 BASIC INSPECTION 287 DIAGNOSIS AND REPAIR WORK FLOW 287 Work Flow 287 Diagnostic Work Sheet 288 ADDITIONAL SERVICE WHEN REPLACING TCM 290 Description .290 Work Procedure .290 ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY 292 Description .292 Work Procedure .292 ADDITIONAL SERVICE WHEN REPLACING TCM AND TRANSAXLE ASSEMBLY 294 Description .294 Work Procedure .294 CVT FLUID 296 Replacement 296 Adjustment .297 STALL TEST 299 Work Procedure .299 CVT POSITION 300 Revision: July 2014 U1117 LOST COMMUNICATION (ABS) 308 DTC Logic 308 Diagnosis Procedure 308 P062F EEPROM 309 Description 309 DTC Logic 309 Diagnosis Procedure 309 P0705 TRANSMISSION RANGE SENSOR A 310 DTC Logic 310 Diagnosis Procedure 310 Component Inspection 314 P0706 TRANSMISSION RANGE SENSOR A 316 DTC Logic 316 Diagnosis Procedure 316 Component Inspection 318 P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A 319 DTC Logic 319 Component Function Check 320 Diagnosis Procedure 320 Component Inspection 321 P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A 322 TM-6 2015 Model L33 DTC Logic 322 Diagnosis Procedure 322 Component Inspection 322 P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A 324 DTC Logic 324 Diagnosis Procedure 324 Component Inspection 325 P0715 INPUT SPEED SENSOR A 326 DTC Logic 326 Diagnosis Procedure 327 P0717 INPUT SPEED SENSOR A 329 DTC Logic 329 Diagnosis Procedure 330 P0740 TORQUE CONVERTER 332 DTC Logic 332 Diagnosis Procedure 333 P0743 TORQUE CONVERTER 334 DTC Logic 334 Diagnosis Procedure 335 P0744 TORQUE CONVERTER 336 DTC Logic 336 Diagnosis Procedure 337 P0746 PRESSURE CONTROL SOLENOID A 338 DTC Logic 338 Diagnosis Procedure 339 P0776 PRESSURE CONTROL SOLENOID B 340 DTC Logic 340 Diagnosis Procedure 341 P0778 PRESSURE CONTROL SOLENOID B 342 DTC Logic 342 Diagnosis Procedure 342 P0779 PRESSURE CONTROL SOLENOID B 344 DTC Logic 344 Diagnosis Procedure 344 P0841 TRANSMISSION FLUID PRESSURE SEN/SW A 346 DTC Logic 346 Diagnosis Procedure 346 P0847 TRANSMISSION FLUID PRESSURE SEN/SW B 347 DTC Logic 347 Diagnosis Procedure 347 P0848 TRANSMISSION FLUID PRESSURE SEN/SW B 349 DTC Logic 349 Diagnosis Procedure 349 Revision: July 2014 P084C TRANSMISSION FLUID PRESSURE SEN/SW H 351 A DTC Logic 351 Diagnosis Procedure 351 P084D TRANSMISSION FLUID PRESSURE SEN/SW H 353 DTC Logic 353 Diagnosis Procedure 353 B C P0863 TCM COMMUNICATION 355 DTC Logic 355 Diagnosis Procedure 355 P0890 TCM 356 DTC Logic 356 Diagnosis Procedure 356 P0962 PRESSURE CONTROL SOLENOID A 357 DTC Logic 357 Diagnosis Procedure 357 P0963 PRESSURE CONTROL SOLENOID A 359 TM E F G DTC Logic 359 Diagnosis Procedure 359 P0965 PRESSURE CONTROL SOLENOID B 361 DTC Logic 361 Diagnosis Procedure 362 P0966 PRESSURE CONTROL SOLENOID B 363 DTC Logic 363 Diagnosis Procedure 363 H I J P0967 PRESSURE CONTROL SOLENOID B 365 DTC Logic 365 Diagnosis Procedure 365 K P2765 INPUT SPEED SENSOR B 367 DTC Logic 367 Diagnosis Procedure 368 L P2813 SELECT SOLENOID 370 DTC Logic 370 Diagnosis Procedure 371 P2814 SELECT SOLENOID 372 M DTC Logic 372 Diagnosis Procedure 372 N P2815 SELECT SOLENOID 374 O DTC Logic 374 Diagnosis Procedure 374 MAIN POWER SUPPLY AND GROUND CIRCUIT 376 Diagnosis Procedure 376 SHIFT POSITION INDICATOR CIRCUIT 378 TM-7 Component Parts Function Inspection 378 Diagnosis Procedure 378 2015 Model L33 P SHIFT LOCK SYSTEM 379 DIFFERENTIAL SIDE OIL SEAL 407 Component Function Check 379 Diagnosis Procedure .379 Component Inspection (Shift Lock Solenoid) 380 Component Inspection (Park Position Switch) 380 Component Inspection (Stop Lamp Switch) 381 Exploded View 407 Removal and Installation 407 Inspection and Adjustment 408 SYMPTOM DIAGNOSIS 382 CVT CONTROL SYSTEM 382 Symptom Table .382 PERIODIC MAINTENANCE 386 CVT FLUID 386 Inspection 386 REMOVAL AND INSTALLATION 387 CVT SHIFT SELECTOR 387 Exploded View .387 Removal and Installation .387 Inspection 388 CONTROL CABLE 389 Exploded View .389 Removal and Installation .389 Inspection and Adjustment 390 CVT OIL WARMER SYSTEM 409 WATER HOSE 409 WATER HOSE : Exploded View 409 WATER HOSE : Removal and Installation 409 WATER HOSE : Inspection 411 CVT FLUID COOLER HOSE 411 CVT FLUID COOLER HOSE : Exploded View 411 CVT FLUID COOLER HOSE : Removal and Installation 412 CVT FLUID COOLER HOSE : Inspection 413 CVT OIL WARMER 413 CVT OIL WARMER : Exploded View 413 CVT OIL WARMER : Removal and Installation 413 CVT OIL WARMER : Inspection 414 CVT FLUID COOLER 415 Exploded View (GCC) 415 Removal and Installation (GCC) 415 PLUG 416 Exploded View .391 Removal and Installation .391 Description 416 Exploded View 416 Removal and Installation 416 Inspection and Adjustment 416 TCM 393 UNIT REMOVAL AND INSTALLATION 417 Exploded View .393 Removal and Installation .393 Adjustment .394 TRANSMISSION ASSEMBLY 417 PADDLE SHIFTER 391 AIR BREATHER HOSE 395 Removal and Installation .395 CONTROL VALVE 396 Exploded View .396 Removal and Installation .397 Inspection 401 INPUT SPEED SENSOR 402 Exploded View .402 Removal and Installation .402 Inspection and Adjustment 402 PRIMARY SPEED SENSOR 404 Exploded View .404 Removal and Installation .404 Inspection and Adjustment 404 OUTPUT SPEED SENSOR 406 Exploded View .406 Removal and Installation .406 Inspection and Adjustment 406 Revision: July 2014 Exploded View 417 Removal and Installation 417 Inspection and Adjustment 419 UNIT DISASSEMBLY AND ASSEMBLY 420 TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL 420 Exploded View 420 Disassembly 420 Assembly 420 Inspection 421 SERVICE DATA AND SPECIFICATIONS (SDS) 423 SERVICE DATA AND SPECIFICATIONS (SDS) 423 General Specification 423 Shift Characteristics 423 Stall Speed 423 Torque Converter 423 Heater Thermostat 423 TM-8 2015 Model L33 HOW TO USE THIS SECTION [CVT: RE0F10D] < HOW TO USE THIS MANUAL > HOW TO USE THIS MANUAL A HOW TO USE THIS SECTION Information INFOID:0000000011369825 B Names in service manual depend on vehicle destinations For details, refer to the following table C Destination Service manual name Except for Israel For Israel Sport mode Sport mode O/D OFF Sport mode switch Sport mode switch Overdrive control switch SPORT indicator lamp SPORT indicator lamp O/D OFF indicator lamp TM E F G H I J K L M N O P Revision: July 2014 TM-9 2015 Model L33 PRECAUTIONS [CVT: RE0F10D] < PRECAUTION > PRECAUTION PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000010529811 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision Information necessary to service the system safely is included in the SR and SB section of this Service Manual WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module, see the SR section • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery and wait at least three minutes before performing any service Precautions Necessary for Steering Wheel Rotation after Battery Disconnect INFOID:0000000010529812 CAUTION: Comply with the following cautions to prevent any error and malfunction • Before removing and installing any control units, first turn the ignition switch to the LOCK position, then disconnect both battery cables • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables • Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing work If a DTC is detected, perform trouble diagnosis according to self-diagnosis results This vehicle is equipped with a push-button ignition switch and a steering lock unit If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure below before starting the repair operation OPERATION PROCEDURE Connect both battery cables NOTE: Supply power using jumper cables if battery is discharged Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position (At this time, the steering lock will be released.) Disconnect both battery cables The steering lock will remain released with both battery cables disconnected and the steering wheel can be turned Perform the necessary repair operation When the repair work is completed, re-connect both battery cables With the brake pedal released, turn the push-button ignition switch from ACC position to ON position, then to LOCK position (The steering wheel will lock when the push-button ignition switch is turned to LOCK position.) Perform self-diagnosis check of all control units using CONSULT Revision: July 2014 TM-10 2015 Model L33 STARTING SYSTEM < WIRING DIAGRAM > ABBIA2517GB Revision: July 2014 STR-12 2015 Model L33 DIAGNOSIS AND REPAIR WORKFLOW < BASIC INSPECTION > BASIC INSPECTION A DIAGNOSIS AND REPAIR WORKFLOW Work Flow (With GR8-1200 NI) INFOID:0000000010532558 STR STARTING SYSTEM DIAGNOSIS WITH GR8-1200 NI To test the starting system, use the following special service tool: • GR8-1200 NI Multitasking battery and electrical diagnostic station NOTE: Refer to the diagnostic station Instruction Manual for proper starting system diagnosis procedures C D E F G H I J K L M N O P Revision: July 2014 STR-13 2015 Model L33 DIAGNOSIS AND REPAIR WORKFLOW < BASIC INSPECTION > OVERALL SEQUENCE AWBIA1200GB DETAILED FLOW NOTE: To ensure a complete and thorough diagnosis, the battery, starter motor and generator test segments must be done as a set from start to finish 1.DIAGNOSIS WITH MULTITASKING BATTERY AND ELECTRICAL DIAGNOSTIC STATION GR8-1200 NI Revision: July 2014 STR-14 2015 Model L33 DIAGNOSIS AND REPAIR WORKFLOW < BASIC INSPECTION > Perform the starting system test with Multitasking battery and electrical diagnostic station GR8-1200 NI For details and operating instructions, refer to diagnostic station Instruction Manual A Test result CRANKING NORMAL>>GO TO LOW VOLTAGE>>GO TO STR CHARGE BATTERY>>Perform the slow battery charging procedure (Initial rate of charge is 10A for 12 hours.) Perform battery test again Refer to diagnostic station instruction manual REPLACE BATTERY>>Before replacing battery, clean the battery cable clamps and battery posts Perform C battery test again Refer to diagnostic station instruction manual If second test result is “REPLACE BATTERY”, then so Perform battery test again to confirm repair 2.CRANKING CHECK D Check that the starter motor operates properly Does the engine crank normally? YES >> GO TO NO >> GO TO E 3.ENGINE START CHECK Check that the engine starts Does the engine start? YES >> Inspection End NO >> Perform further diagnosis of engine mechanical or engine control system Refer to EM and EC sections Once resolved, perform battery test again 4.STARTER MOTOR ACTIVATION F G H Check that the starter motor operates Does the starter motor turn? YES >> Check ring gear and starter motor drive pinion Once resolved, perform battery test again NO >> GO TO 5.COMPARISON BETWEEN ENGINE COOLANT AND CRANKING VOLTAGE Compare the engine coolant temperature and verify the cranking voltage is within specifications I J Minimum Specification of Cranking Voltage Referencing Coolant Temperature Engine coolant temperature [°C (°F)] Voltage [V] −30 to −20 (−22 to −4) 8.6 −19 to −10 (−2 to 14) 9.1 −9 to (16 to 32) 9.5 More than (More than 34) 9.9 K L Is the voltage less than the specified value? YES >> GO TO NO >> GO TO M 6.STARTER OPERATION N Check the starter operation Does the starter motor turn smoothly? YES >> Inspection End NO >> GO TO O 7.“B” TERMINAL CIRCUIT INSPECTION P Check “B” terminal circuit Refer to STR-19, "Diagnosis Procedure" Is “B” terminal circuit normal? YES >> GO TO NO >> Repair as needed 8.“S” CONNECTOR CIRCUIT INSPECTION Check “S” connector circuit Refer to STR-19, "Diagnosis Procedure" Revision: July 2014 STR-15 2015 Model L33 DIAGNOSIS AND REPAIR WORKFLOW < BASIC INSPECTION > Is “S” connector circuit normal? YES >> GO TO NO >> Repair as needed 9.ENGINE ROTATION STATUS Check that the engine can be rotated by hand Does the engine turn freely by hand? YES >> Replace starter motor Refer to STR-23, "QR25DE : Removal and Installation" (QR25DE) or STR24, "VQ35DE : Removal and Installation" (VQ35DE) NO >> Perform further diagnosis of engine mechanical or powertrain mechanism Once resolved, perform battery test again using Multitasking battery and electrical diagnostic station GR8-1200 NI Refer to the diagnostic station Instruction Manual for proper testing procedures Work Flow (Without GR8-1200 NI) INFOID:0000000010532559 OVERALL SEQUENCE Revision: July 2014 STR-16 2015 Model L33 DIAGNOSIS AND REPAIR WORKFLOW < BASIC INSPECTION > If any malfunction is found, immediately disconnect the battery cable from the negative terminal A STR C D E F G H I J K L M N AWBIA1303GB DETAILED FLOW NOTE: If any malfunction is found, immediately disconnect the battery cable from the negative terminal 1.CHECK ENGINE START P Crank the engine and check that the engine starts Does the engine start? YES >> GO TO NO >> GO TO 2.CHECK THAT THE STARTER MOTOR STOPS Check that the starter motor stops after starting the engine Revision: July 2014 O STR-17 2015 Model L33 DIAGNOSIS AND REPAIR WORKFLOW < BASIC INSPECTION > Does the starter motor stop? YES >> Inspection End NO >> Replace starter motor Refer to STR-23, "QR25DE : Removal and Installation" (QR25DE) or STR24, "VQ35DE : Removal and Installation" (VQ35DE) 3.CHECK THAT THE ENGINE TURNS WHEN CRANKING Check that the engine turns when cranking Does engine turn when cranking? YES >> GO TO NO >> GO TO 4.CHECK THE ENGINE SPEED WHEN CRANKING Check that the engine speed is not low when cranking Does engine turn normally? YES >> Check ignition/fuel system NO >> Check charge condition, corrosion and connection condition of the battery 5.CHECK STARTER MOTOR ACTIVATION Check that the starter motor runs at cranking Does starter motor turn? YES >> Replace starter motor Refer to STR-23, "QR25DE : Removal and Installation" (QR25DE) or STR24, "VQ35DE : Removal and Installation" (VQ35DE) NO >> GO TO 6.CHECK POWER SUPPLY CIRCUIT Check the following conditions: • Fuse and fusible link • Charge condition, corrosion and connection of the battery Are these inspection results normal? YES >> GO TO NO >> Repair as needed 7.CHECK STARTING SYSTEM WIRING Check the following: • “B” terminal circuit Refer to STR-19, "Diagnosis Procedure" • “S” terminal circuit Refer to STR-21, "Diagnosis Procedure" Are the inspection results normal? YES >> Replace starter motor Refer to STR-23, "QR25DE : Removal and Installation" (QR25DE) or STR24, "VQ35DE : Removal and Installation" (VQ35DE) NO >> Repair as needed Revision: July 2014 STR-18 2015 Model L33 B TERMINAL CIRCUIT < DTC/CIRCUIT DIAGNOSIS > DTC/CIRCUIT DIAGNOSIS A B TERMINAL CIRCUIT Description INFOID:0000000010532560 STR INFOID:0000000010532561 C Terminal “B” is constantly supplied with battery power Diagnosis Procedure Regarding Wiring Diagram information, refer to STR-8, "Wiring Diagram" D CAUTION: Perform diagnosis under the condition that the engine cannot start by the following procedure Remove fuel pump fuse Crank or start the engine (where possible) until the fuel pressure is released E 1.CHECK “B” TERMINAL CIRCUIT F G Turn ignition switch OFF Check that starter motor B” terminal connection is clean and tight Check voltage between starter motor connector F27 and ground Terminals (+) Starter motor “B” terminal Terminal F27 B (-) Voltage (Approx.) Ground Battery voltage H I Is the inspection result normal? YES >> GO TO NO >> Check harness between battery and starter motor for open circuit J K 2.CHECK BATTERY CABLE CONNECTION STATUS (VOLTAGE DROP TEST) Shift selector lever to P (Park) or N (Neutral) position Check voltage between battery positive terminal and starter motor B terminal Terminals (-) (+) Starter motor “B“ terminal Terminal Battery positive terminal F27 B Condition Voltage (Approx.) When the ignition switch is in START position Less than 0.5V Is the inspection result normal? YES >> GO TO NO >> Check harness between the battery and starter motor for continuity O Shift selector lever to P (Pack) or N (Neutral) position Check voltage between starter motor case and battery negative terminal Terminals (+) (-) Starter motor case Battery negative terminal Condition Voltage (Approx.) When the ignition switch is in START position Less than 0.2V Is the inspection result normal? Revision: July 2014 STR-19 M N 3.CHECK GROUND CIRCUIT STATUS (VOLTAGE DROP TEST) L 2015 Model L33 P B TERMINAL CIRCUIT < DTC/CIRCUIT DIAGNOSIS > YES >> “B” terminal circuit is OK Further inspection is necessary Refer to STR-13, "Work Flow (With GR8-1200 NI)" or STR-16, "Work Flow (Without GR8-1200 NI)" NO >> Check the starter motor case to engine mounting for high resistance Revision: July 2014 STR-20 2015 Model L33 S CONNECTOR CIRCUIT < DTC/CIRCUIT DIAGNOSIS > S CONNECTOR CIRCUIT A Description INFOID:0000000010532562 The starter motor magnetic switch is supplied with power when the ignition switch is turned to the START posi- STR tion while the selector lever is in the P (Park) or N (Neutral) position Diagnosis Procedure INFOID:0000000010532563 C Regarding Wiring Diagram information, refer to STR-8, "Wiring Diagram" D CAUTION: Perform diagnosis under the condition that engine cannot start by the following procedure Remove fuel pump fuse Crank or start the engine (where possible) until the fuel pressure is released 1.CHECK “S” CONNECTOR CIRCUIT Turn ignition switch OFF Disconnect starter motor connector Shift selector lever to “P” (Park) or “N” (Neutral) position Check voltage between starter motor harness connector F28 (QR25DE) or F81 (VQ35DE) and ground (+) Connector F28 (QR25DE) F81 (VQ35DE) (-) Condition Voltage (Approx.) When the ignition switch is in START position Battery voltage Terminal S Ground Is the inspection result normal? YES >> “S” circuit is OK Further inspection is necessary Refer to STR-13, "Work Flow (With GR8-1200 NI)" or STR-16, "Work Flow (Without GR8-1200 NI)" NO >> GO TO E F G H I J 2.CHECK HARNESS CONTINUITY (OPEN CIRCUIT) Disconnect IPDM E/R connector Check continuity between starter motor harness connector F28 (QR25DE) or F81 (VQ35DE) and the IPDM E/R harness connector F10 K L Starter motor harness connector Connector F28 (QR25DE) F81 (VQ35DE) IPDM E/R harness connector Terminal Connector Terminal S F10 51 Continuity Yes Is the inspection result normal? YES >> Further inspection is necessary Refer to STR-13, "Work Flow (With GR8-1200 NI)" or STR-16, "Work Flow (Without GR8-1200 NI)" NO >> Repair or replace the harness or connectors M N O P Revision: July 2014 STR-21 2015 Model L33 STARTING SYSTEM < SYMPTOM DIAGNOSIS > SYMPTOM DIAGNOSIS STARTING SYSTEM Symptom Table INFOID:0000000010532564 Symptom No normal cranking Starter motor does not rotate Revision: July 2014 Reference Refer to STR-13, "Work Flow (With GR8-1200 NI)" or STR-16, "Work Flow (Without GR8-1200 NI)" STR-22 2015 Model L33 STARTER MOTOR < REMOVAL AND INSTALLATION > REMOVAL AND INSTALLATION A STARTER MOTOR QR25DE STR QR25DE : Exploded View INFOID:0000000010532565 C D E F G H I J AWBIA1296GB Converter housing Starter motor “B” terminal harness QR25DE : Removal and Installation “S” connector K INFOID:0000000010532566 L REMOVAL Remove the core support cover clips (A), then remove the core support cover (1) M N O ALKIA2602ZZ Remove battery tray Refer to PG-84, "Removal and Installation" Disconnect the starter motor harness connectors Remove the two starter motor bolts, using power tools Remove the starter motor INSTALLATION Revision: July 2014 STR-23 2015 Model L33 P STARTER MOTOR < REMOVAL AND INSTALLATION > Installation is in the reverse order of removal • Perform "Throttle Valve Closed Position Learning" Refer to EC-167, "Work Procedure" [QR25DE (TYPE 1)] or EC-647, "Work Procedure" [QR25DE (TYPE 2)] • Perform "Accelerator Pedal Release Position Learning" Refer to EC-166, "Work Procedure" [QR25DE (TYPE 1)] or EC-646, "Work Procedure" [QR25DE (TYPE 2)] VQ35DE VQ35DE : Exploded View INFOID:0000000010532567 AWBIA2136ZZ Cylinder block Shim "B" terminal harness "S" connector VQ35DE : Removal and Installation Starter motor INFOID:0000000010532568 REMOVAL Remove the core support cover clips (A), then remove the core support cover (1) ALKIA2602ZZ Remove the battery tray Refer to PG-84, "Removal and Installation" Disconnect the ”S” connector and the ”B” terminal Remove the two starter motor bolts, using power tools Remove the starter motor Revision: July 2014 STR-24 2015 Model L33 STARTER MOTOR < REMOVAL AND INSTALLATION > INSTALLATION A Installation is in the reverse order of removal • Perform "Throttle Valve Closed Position Learning" Refer to EC-1019, "Work Procedure" [VQ35DE (TYPE 1)] or EC-1469, "Work Procedure" [VQ35DE (TYPE 2)] • Perform "Accelerator Pedal Release Position Learning" Refer to EC-1468, "Work Procedure" [VQ35DE STR (TYPE 1)] or EC-1468, "Work Procedure" [VQ35DE (TYPE 2)] C D E F G H I J K L M N O P Revision: July 2014 STR-25 2015 Model L33 STARTER MOTOR < SERVICE DATA AND SPECIFICATIONS (SDS) SERVICE DATA AND SPECIFICATIONS (SDS) STARTER MOTOR Starter INFOID:0000000010532569 QR25DE Application VQ35DE CVT model Manufacturer Mitsubishi Model number* M000TB0071ZC Type Reduction gear type System voltage 12V Terminal voltage No-load M000TA0073ZC 11V Current Revolution Less than 90A More than 2,370 rpm More than 2,400 rpm *: Always check with the Parts Department for the latest parts information Revision: July 2014 STR-26 2015 Model L33