... Thao tác Chính xác, hợp lý 14 Thời gian Không vợt quá thời gian quy định 15 An toàn Không xẩy ra tai nạn, không làm hỏng thiết bị 16 Tổ chức nơi làm việc Sạch sẽ, ngăn nắp, gọn gàng 0,5Tổng cộng ... Thao tác Chính xác, hợp lý 14 Thời gian Không vợt quá thời gian quy định 15 An toàn Không xẩy ra tai nạn, không làm hỏng thiết bị 16 Tổ chức nơi làm việc Sạch sẽ, ngăn nắp, gọn gàng 0,5Tổng cộng ... Thao tác Chính xác, hợp lý 14 Thời gian Không vợt quá thời gian quy định 15 An toàn Không xẩy ra tai nạn, không làm hỏng thiết bị 16 Tổ chức nơi làm việc Sạch sẽ, ngăn nắp, gọn gàng 0,5Tổng cộng...
... Thao tác Chính xác, hợp lý 14 Thời gian Không vợt quá thời gian quy định 15 An toàn Không xẩy ra tai nạn, không làm hỏng thiết bị 16 Tổ chức nơi làm việc Sạch sẽ, ngăn nắp, gọn gàng 0,5Tổng cộng ... Thao tác Chính xác, hợp lý 14 Thời gian Không vợt quá thời gian quy định 15 An toàn Không xẩy ra tai nạn, không làm hỏng thiết bị 16 Tổ chức nơi làm việc Sạch sẽ, ngăn nắp, gọn gàng 0,5Tổng cộng ... Thao tác Chính xác, hợp lý 14 Thời gian Không vợt quá thời gian quy định 15 An toàn Không xẩy ra tai nạn, không làm hỏng thiết bị 16 Tổ chức nơi làm việc Sạch sẽ, ngăn nắp, gọn gàng 0,5Tổng cộng...
... ngời lái xe và hành khách đi trên xe, vì hệ thống lái không đảm bảo an toàn sẽ trực tiếp gây ra tai nạn giao thông và đe doạ đến tính mạng của con ngời. Do đó công việc sửachữa không chỉ cần...
... theequipment’s 9 volt battery,- if a value other than 0 is displayed, operatescrew (F) until 0 is obtained .07-7 SPECIFICATIONSVehicle identification01This consists of:At A: the manufacturer’s ... the trim identification code.NOTE: some of these items of information are not required for certain export markets. The plates describedabove are shown in their most complete form.ALLOCATION ... manufacturing number is 7 numbers.NOTE: some of these items of information are not required for certain export markets. The plates describedabove are shown in their most complete form.40 0 0 00...
... by the samenumber of turns in opposite directions on the left handand right hand sides, to obtain the same reading fordimension A on both sides.INCORRECTCORRECTAdjust the parallelism by ... caliper,- the pads.CheckingCheck :- the fitting and condition of the piston dustcover and its retaining ring,- the condition of the dust covers (8) on theguides.Fit the new pads, together with ... with genuinereplacement parts and refit the seal, the pistonand the dust cover (fitting the retaining ring onthe GIRLING assembly).Using a thin blade with rounded edges (forexample a feeler...
... be removed in oneposition).Disconnect the motor connector.Open the two half covers.Pull the motor out as shown below.When refitting, put the motor back in position sothat the connector is ... refrigerant level.Check that the mixing flap moves when thecontrol is moved.Is there movement?Visually check on the assembly that the flap travelis correct.Adjust if necessary.Does the fault ... winter, operate thecompressor periodically in order to preventdestruction of the compressor rotor bearing races.The needles mark the bearing races when theassembly is immobilised in one position...
... NAUDER*and stainless steel clips2 - Rivets Part number : 77 03 072 2803 - Neoprene adhesive4 - Brush5 - Seal Part number:* NAUDER :Please contact your local After Sales Head Officefor details.94791SGENERALTooling ... 53CABRIOLETAfter removing the external trim, remove the ri-vets from the rear section and the stainless steelclips.Remove the adhesive tape from the front section.Unstick the front section.73-7 ... hooks (2).Unclip the trim.TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE)Bonnet trim73APRF7301Tailgate trim73B73-1 REMOVALInsert a flat screwdriver in hole (2) in the uppersection, so...
... SIDE STRUCTUREUPPER REAR STRUCTUREUPPER BODY SECTIONBODY PROTECTIONSIDE OPENINGSBONNET AND TAILGATE ContentsGENERALEngine - Clutch - GearboxVehicle dimensionsLiftingDescription of parts...