... situations. Recommended codeofpracticefor the care and Recommended codeofpracticefor the care and handling of poultry from hatchery to processing planthandling of poultry from hatchery ... Facilities forand handling of loose-housed poultry5.2.1 Proper building design and accessibility to transport vehicles greatly improves the humanehandling of loose-housed poultry. Owners and operators ... and watering space, an adequate and predictable supply of feed and water, and an adequate number of nest boxes and roosts. 142.5 Supervision and protection of chickens2.5.1 Chicken flocks...
... use of steelwork in building — Part 4: Codeofpracticefor design of composite slabs with profiled steel sheeting.BS 5950-5, Structural use of steelwork in building — Part 5: Codeofpractice ... carbon steel bars for the reinforcement of concrete.BS 4482, Specification for cold reduced steel wire for the reinforcement of concrete.BS 4483, Steel fabric for the reinforcement of concrete.BS ... 5: Codeofpracticefor design of cold formed thin gauge sections.BS 5950-6, Structural use of steelwork in building — Part 6: Codeofpracticefor design of light gauge profiled steel sheeting.BS...
... INTERNATIONAL STANDARD ISO/IEC17799 Second edition 2005-06-15Information technology — Security techniques — Codeofpracticefor information security management Technologies de l'information ... Information Labeling and secure handling of classified information is a key requirement for information sharing arrangements. Physical labels are a common form of labeling. However, some information assets, ... guidelines This codeofpractice may be regarded as a starting point for developing organization specific guidelines. Not all of the controls and guidance in this codeofpractice may be applicable....
... conditions and system configurations, can be referenced to codes, guidelines and practices of international standards (such as ASHRAE, CIBSE) or established local standards or trade good practices, for ... forced fan ventilation. ‘Director’ means the Director of Electrical and Mechanical Services. CodeofPracticefor Building Energy Audit EAC_2012 9 of 11 EMSD cost benefit analyses, and ... date of issue of Energy Audit Form, - name and address of building (English and Chinese), - name and Registration No. of Registered Energy Assessor who has carried out the energy audit, and...
... handling;· Manual handling; and · Vehicle and equipment safety. ENVIRONMENTAL CODEOFPRACTICEFOR POULTRY FARMS IN WESTERN AUSTRALIA33PART 4 OTHER CONSIDERATIONS ENVIRONMENTAL CODEOFPRACTICE ... Welfare of Animals: Land Transport of Poultry, available from the Internet site<www.publish.csiro.au> ;and the Department of Local Government and Regional Development’s Code ofPracticefor ... for transportation to the central grading floor in Palmyra for grading and retaildistribution. ENVIRONMENTAL CODEOFPRACTICEFOR POULTRY FARMS IN WESTERN AUSTRALIAiv ENVIRONMENTAL CODE OF...
... information is a shorthand way of determining how this information is to be handled and protected. 7.2.2 Information labeling and handling Control An appropriate set of procedures for information ... INTERNATIONAL STANDARD ISO/IEC17799 Second edition 2005-06-15Information technology — Security techniques — Codeofpracticefor information security management Technologies de l'information ... techniques — Codeof practice for information security management 1 Scope This International Standard establishes guidelines and general principles for initiating, implementing, maintaining, and...
... materials and workmanship: coldformed sections and sheeting.BS 6399-1, Loading for buildings Ð Codeof practice for dead and imposed loads.BS 6399-2, Loading for buildings Ð Codeof practice for ... practicefor protective coating of iron and steel structures against corrosion1).BS 5502-22, Buildings and structures for agriculture Ð Codeofpracticefor design,construction and loading.BS ... properties of fasteners ÐBolts, screws and studs.CP3 Codeof basic data for the design of buildings:Chapter V: Part 2: Wind loads.1.4 Terms and definitions For the purposes of this part of BS...
... 3.4 and 3.5 of BS 8110-1:1985 or Tables 5.1 and 5.2 of BS 8110-2:1985.Figure 4 — Typical profiles BRITISH STANDARDBS 5950-4:1994Structural use of steelwork in building —Part 4: Codeofpractice ... loadDpOverall depth of profiled steel sheetsDsOverall depth of composite slabdsEffective depth of slab to centroid of profiled steel sheetsE Modulus of elasticity of profiled steel sheetsFaEnd ... recommendations for thedesign of composite slabs with profiled steel sheeting. It covers slabs spanning only in the direction of span of the profiled steel sheets.This code applies to the design of composite...
... of first stiffenerhsbVertical depth ofsecond stiffenerIeffEffective second moment of area of a sectionIminMinimum required second moment of area of an effective edge stiffenerIr Second ... Rt,0.5 and Rmshould normally be taken as specified in the relevant product standard for the steel sheet or strip and used for the formed sections. For information, the resulting values of Ys and ... Properties of materials and section properties3.1 Range of thicknessesThe provisions of this Part of BS 5950 apply primarily to profiled steel sheet with a net thickness of steel basemetal of not...
... 3.1: Codeofpracticefor design of simple and continuous composite beams;— Section 3.21): Codeofpracticefor design of composite columns and frames;— Part 4: Codeofpracticefor design of ... Specification for materials and workmanship: cold formed sections;— Part 8: Codeofpracticefor fire resistant design;— Part 91): Codeofpracticefor stressed skin design.This Part of BS5950 ... the second moment of area of concrete core in the plane of buckling;Ir is the second moment of area of the reinforcement in the plane of buckling;Er is the modulus of elasticity of reinforcement;fy...
... 3.1 Codeofpracticefor design of simple and continuous composite beams;— Part 4: Codeofpracticefor design of composite slabs with profiled steel sheeting;— Part 5: Codeofpracticefor ... design of cold formed sections;— Part 61): Codeofpracticefor design of light gauge profiled sheeting;— Part 7: Specification for materials and workmanship: cold formed sections;— Part 8: Code ... sections;— Part 8: Codeofpracticefor fire resistant design;— Part 9: Codeofpracticefor stressed skin design.This Part of BS 5950 gives recommendations for the use of profiled steel sheeting...