2000 toyota camry manual transmission

Ngày tải lên: 23/05/2014, 16:02

Ngày tải lên: 24/05/2014, 13:18

Ngày tải lên: 24/05/2014, 13:31

Ngày tải lên: 24/05/2014, 13:47

Ngày tải lên: 14/12/2013, 15:10

Ngày tải lên: 25/12/2013, 12:33

Ngày tải lên: 29/12/2013, 11:16

... LUBRICATION SYSTEM LU (f) Apply adhesive to 2 or 3 threads of the oil pressure switch. Adhesive: Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent (g) Using a 24 mm deep socket wrench, ... SUB-ASSEMBLY Non-reusable part 13 (133, 10) A134971E01 2AZ-FE LUBRICATION – OIL PUMP LU–17 LU Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent NOTICE: ã Remove any oil from ... packing (diameter: 4.0 to 4.5 mm (0.157 to 0.177 in.)) as shown in the illustration. Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent (c) Apply seal packing in a continuous...

Ngày tải lên: 23/05/2014, 16:26

Ngày tải lên: 23/05/2014, 16:26

... Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC). Specified capacity: 6.2 liters (6.6 US qts, 5.5 lmp. qts) HINT: ã TOYOTA vehicles are filled with TOYOTA SLLC at the factory. ... surface. (b) Apply a continuous line of seal packing as shown in the illustration. Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent Standard seal diameter: 2.2 to ... lines when the engine is cold. If the engine coolant level is low, check for leaks and add " ;TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate,...

Ngày tải lên: 23/05/2014, 16:27

... VENTILATION VALVE SUB-ASSEMBLY (a) Apply adhesive to 2 or 3 threads of the ventilation valve. Adhesive: Toyota genuine adhesive 1324, three bond 1324 or equivalent (b) Using a 22 mm deep socket wrench,...

Ngày tải lên: 23/05/2014, 16:27

... circuit open ENGINE SPD Engine speed: Min.: 0 rpm, Max.: 16,383.75 rpm 650 to 750 rpm: Idling (Manual transaxle) 610 to 710 rpm: Idling (Automatic transaxle) - VEHICLE SPD Vehicle speed: Min.: ... terminal Results Condition SIL 7 Bus "+" line 5 - Signal ground Pulse generation During transmission CG 4 Chassis ground Body ground 1 Ω or less Always SG 5 Signal ground Body ground 1 ... vehicle at between 38 mph (60 km/h) and 75 mph (120 km/h) for at least 10 minutes. (7) Change the transmission to the 2nd gear. (8) Accelerate the vehicle to 40 mph (64 km/h) or more by depressing...

Ngày tải lên: 23/05/2014, 16:29

... light coat of engine oil to the threads and under the heads of the bearing cap bolts. 08 5.080 (0 .2000) 32 5.320 (0.2094) 56 5.560 (0.2189) 10 5.100 (0.2008) 34 5.340 (0.2102) 58 5.580 (0.2197) 12 ... 0.0409) 1.041 - 1.060 (0.0410 - 0.0417) 1.061 - 1.080 (0.0418 - 0.0425) 5.060 (0.1992) 5.080 (0 .2000) 5.100 (0.2008) 5.120 (0.2016) 5.140 (0.2024) 5.160 (0.2031) 5.180 (0.2039) 5.200 (0.2047) 5.210 ... tester. Ignition timing: 8 to 12° BTDC at idle HINT: Refer to the intelligent tester operator's manual for help when selecting the DATA LIST. (c) When not using the intelligent tester: Check...

Ngày tải lên: 23/05/2014, 16:33

Ngày tải lên: 23/05/2014, 16:33

... the hose clamp and disconnect the fuel tank to filter pipe hose. ( * 2) (f) Slightly lower the transmission jack. (g) Disconnect the fuel tank vent hose from the charcoal canister. ( * 3) (1)...

Ngày tải lên: 23/05/2014, 16:34

Ngày tải lên: 23/05/2014, 16:34

Ngày tải lên: 23/05/2014, 16:34

... securely connected by trying to pull them apart. (b) Install the No. 1 fuel pipe clamp. 54. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (a) Install the clip and nut, and connect the cable to the ... ASSEMBLY EM FRONT FENDER APRON SEAL RH FUEL TUBE SUB-ASSEMBLY RADIATOR HOSE INLET RADIATOR HOSE OUTLET TRANSMISSION CONTROL CABLE ASSEMBLY COOLER COMPRESSOR ASSEMBLY ENGINE MOVING CONTROL ROD SUB-ASSEMBLY NO. ... bolts and 2 clamps from the body. (c) Remove the bolt and clamp from the bracket. 35. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (a) Remove the clip and nut, and separate the cable from the...

Ngày tải lên: 23/05/2014, 16:53

... ASSEMBLY N*m (kgf*cm, ft.*lbf) : Specified torque 9.8 (100, 87 in.*lbf) 37 (380, 28) 12 (120, 9) for Manual Transaxle: CLUTCH FLEXIBLE HOSE BRACKET x2 AIR CLEANER CAP SUB-ASSEMBLY AIR CLEANER CASE ... ES-416) 4. REMOVE AIR CLEANER CASE SUB-ASSEMBLY (See page EM-95) 5. REMOVE STARTER ASSEMBLY (for Manual Transaxle) (a) Disconnect the terminal 50 connector from the starter assembly. (b) Remove ... with the nut. Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) INSTALLATION 1. INSTALL STARTER ASSEMBLY (for Manual Transaxle) (a) Install the starter assembly and clutch flexible hose bracket with the 3...

Ngày tải lên: 23/05/2014, 16:53

Ngày tải lên: 23/05/2014, 16:54