HỆ THỐNG ĐIỀU KHIỂN KHÍ XẢ TRÊN TOYOTA CAMRY 2AZ-FE ĐỜI 2006-2011
2AZ-FE EXHAUST – EXHAUST PIPE EX–1 EX ENGINE2AZ-FE EXHAUST EXHAUST PIPE COMPONENTS REAR EXHAUST PIPE NO. 1 SUPPORT BRACKET EXHAUST PIPE SUPPORT NO. 4 EXHAUST PIPE SUPPORT NO. 4 43 (438, 32) 43 (438, 32) 44 (449, 32) 33 (337, 24) 33 (337, 24) GASKET GASKET GASKET 43 (438, 32) EXHAUST PIPE SUPPORT NO. 4 EXHAUST PIPE SUPPORT NO. 4 EXHAUST PIPE SUPPORT NO. 4 EXHAUST PIPE SUPPORT NO. 4 EXHAUST PIPE SUPPORT NO. 4 Non-reusable part N*m (kgf*cm, ft.*lbf) : Specified torque 43 (438, 32) CENTER EXHAUST PIPE ASSEMBLY FRONT EXHAUST PIPE ASSEMBLY TAIL PIPE ASSEMBLY TAIL PIPE ASSEMBLY HEATED OXYGEN SENSOR FRONT EXHAUST PIPE NO. 1 SUPPORT BRACKET A135662E01 EX–2 2AZ-FE EXHAUST – EXHAUST PIPE EX REMOVAL 1. REMOVE TAIL PIPE ASSEMBLY (a) Remove the 2 nuts and tail pipe assembly. (b) Remove the gasket from the center exhaust pipe. 2. REMOVE CENTER EXHAUST PIPE ASSEMBLY (a) Remove the 2 bolts, 2 nuts and center exhaust pipe assembly. (b) Remove the gasket from the front exhaust pipe. A135689E01 A135690E01 2AZ-FE EXHAUST – EXHAUST PIPE EX–3 EX 3. REMOVE FRONT EXHAUST PIPE ASSEMBLY (a) Remove the 2 nuts. (b) Remove the 2 nuts, front exhaust pipe No. 1 support bracket and front exhaust pipe assembly. (c) Remove the gasket from the exhaust manifold. 4. REMOVE HEATED OXYGEN SENSOR (See page EC- 24) 5. REMOVE REAR EXHAUST PIPE NO. 1 SUPPORT BRACKET (a) Remove the 2 bolts and rear support bracket. INSTALLATION 1. INSTALL REAR EXHAUST PIPE NO. 1 SUPPORT BRACKET (a) Install the rear support bracket with the 2 bolts. Torque: 33 N*m (337 kgf*cm, 24 ft.*lbf) NOTICE: Be sure to install the bracket in the correct direction. 2. INSTALL HEATED OXYGEN SENSOR (See page EC- 24) 3. INSTALL FRONT EXHAUST PIPE ASSEMBLY (a) Install a new gasket onto the front exhaust pipe assembly. A135691 Bracket A132948E01 Pipe Assembly Front Bracket A060823E04 EX–4 2AZ-FE EXHAUST – EXHAUST PIPE EX (b) Install the front exhaust pipe assembly with the 2 nuts. Torque: 43 N*m (438 kgf*cm, 32 ft.*lbf) (c) Install the front exhaust pipe No. 1 support bracket with the 2 nuts . Torque: 33 N*m (337 kgf*cm, 24 ft.*lbf) 4. INSTALL CENTER EXHAUST PIPE ASSEMBLY (a) Install a new gasket onto the front exhaust pipe. (b) Install the center exhaust pipe assembly with the 2 bolts and 2 nuts. A135691 A135690E01 2AZ-FE EXHAUST – EXHAUST PIPE EX–5 EX Torque: 43 N*m (438 kgf*cm, 32 ft.*lbf) 5. INSTALL TAIL PIPE ASSEMBLY (a) Install a new gasket onto the tail pipe assembly. (b) Install the tail pipe assembly with the 2 nuts. Torque: 43 N*m (438 kgf*cm, 32 ft.*lbf) 6. CHECK FOR EXHAUST GAS LEAKS If gas is leaking, tighten the areas necessary to stop the leak. Replace the damaged parts as necessary. A135689E01 . 2AZ-FE EXHAUST – EXHAUST PIPE EX–1 EX ENGINE2AZ-FE EXHAUST EXHAUST PIPE COMPONENTS REAR EXHAUST PIPE NO. 1 SUPPORT BRACKET EXHAUST PIPE SUPPORT NO. 4 EXHAUST PIPE SUPPORT. 32) CENTER EXHAUST PIPE ASSEMBLY FRONT EXHAUST PIPE ASSEMBLY TAIL PIPE ASSEMBLY TAIL PIPE ASSEMBLY HEATED OXYGEN SENSOR FRONT EXHAUST PIPE NO. 1 SUPPORT BRACKET A135662E01 EX–2 2AZ-FE EXHAUST – EXHAUST. pipe. A135689E01 A135690E01 2AZ-FE EXHAUST – EXHAUST PIPE EX–3 EX 3. REMOVE FRONT EXHAUST PIPE ASSEMBLY (a) Remove the 2 nuts. (b) Remove the 2 nuts, front exhaust pipe No. 1 support bracket and front exhaust pipe