1. Trang chủ
  2. » Công Nghệ Thông Tin

Tài liệu Value-Added Module System Chassis used in Non-ADC Optical Distribution Frame pdf

26 309 0

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 26
Dung lượng 3,36 MB

Nội dung

10/03 • 100571 600 mm Products 53 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 4-Inch Chassis – 6 Single Plug-In Modules The 4-inch VAM chassis fits into any 23-inch rack mounting environment. It accommodates a maximum of six plug-in modules, six bulkhead plates, six blank panels or any combination thereof. Not for use in ADC’s FDF FVM-23X400 Description Unloaded chassis for 23 " racks Catalog Number* FVM-23X400 Dimensions (HxWxD) 4.0" x 23" x 12" (10.16 x 58.42 x 30.48 cm) Ordering Information 3.5-Inch Chassis – 4 Single Plug-In Modules The 3.5-inch VAM chassis fits into any 19-inch rack mounting environment. It accommodates a maximum of four plug-in modules, four bulkhead plates, four blank panels or any combination thereof. Adjustable mounting brackets are provided for 23-inch mounting environments. Not for use in ADC’s FDF FVM-19X350 Description Unloaded chassis for 19" or 23" racks Dimensions (HxWxD) 3.5" x 19" or 23" x 12" (8.89 x 48.26 or 58.26 x 30.48 cm) Ordering Information 1.75-Inch Chassis – 2 Single Plug-In Modules The 1.75-inch VAM chassis fits into any 19-inch rack mounting environment. It accommodates a maximum of two plug-in modules, two bulkhead plates, two blank panels or any combination thereof. Adjustable mounting brackets are provided for 23-inch mounting environments. Not for use in ADC’s FDF FVM-19X175 Description Unloaded chassis for 19" or 23" racks; no front door Dimensions (HxWxD) 1.75" x 19" or 23" x 12" (4.45 x 48.26 or 58.26 x 30.48 cm) Ordering Information Catalog Number* FVM-19X350 Catalog Number* FVM-19X175 Value-Added Module System Chassis used in Non-ADC Optical Distribution Frame * This product is available in black; for this option, simply add “-BK” to the end of the catalog number. Please contact the Technical Assistance Center with any questions. 10/03 • 100571 600 mm Products 54 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Value-Added Module System Introduction ADC’s Value-Added Connector Module System (VAM System) adds flexibility and functionality to the optical transport system by enabling telecommunications service providers to easily incorporate optical components into the network. This versatile platform lays the foundation for the fiber distribution frame of the future. The VAM System consists of a variety of chassis and optical components that fit into all existing ADC fiber distribution frames and various other mounting environments. Optical components may include: • Splitters • Wavelength division multiplexers (WDMs) • Variable attenuators Features and Benefits VAM chassis and modules available for all ADC fiber frames One-stop shop for complete optical transport system requirements Monitor testing Enables providers to troubleshoot networks without forcing disruption of service Enclosed plug-in modules Optical components are protected from physical and environmental damage Angled retainers Maintains minimum bend radius of fiber patch cords Horizontal mounted plug-in modules Modules can be added or removed from the chassis without interfering with existing terminated patch cords Universal mounted plug-in modules No need to order different part numbers for left side or right side mounted modules Extensive product labeling Customers have all the information required for installation and maintenance without referring to the user manual or drawings Flexible platform Modules can be created for new applications quickly and easily to meet customer requirements Module labeling system Schematics are marked on peel-off labels that can be attached to the chassis designation labeling system Custom configurations Custom splitter configurations available upon request, contact ADC Standard VAM Module WideVAM ™ Module OMX ™ VAM Module LGX-compatible VAM module 10/03 • 100571 600 mm Products 55 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Value-Added Module System Splitter Modules Catalog Number Configurations VAM Style Input front, output front Input rear, output front 2 5 Split Ratio** 1x2 1x2 1x2 1x2 1x2 1x2 1x2 1x2 1x2 1x2 1x2 1x2 2x2 1x3 1x4 1x5 1x6 1x7 1x8 1x9 1x10 1x11 1x12 1x13 1x14 1x15 1x16 1x32 50/50 55/45 60/40 65/35 66.6/33.3 70/30 75/25 80/20 85/15 90/10 95/5 99/1 50/50 33/33/33 25/25/25/25 20/20/20/20/20 16.6/16.6/16.6/ 16.6/16.6/16.6 14.3/14.3/14.3/ 14.3/14.3/14.3/14.3 12.5/12.5/ 12.5 11.1/11.1/11.1/ 11.1 10/10/10/ 10 9.1/9.1/9.1/ 9.1 8.33/8.33/8.33/ 8.33 7.7/7.7/7.7/ 7.7 7.14/7.14/7.14/ 7.14 6.66/6.66/6.66/ 6.66 6.25/6.25/6.25/ 6.25 3.125/3.125/3.125/ 3.125 OR 2000 2100 2200 2300 2350 2400 2500 2600 2700 2800 2900 2950 2030 3900 4900 5300 6000 7000 8000 9000 A110 B111 C112 D113 E114 F115 G116 M132 Number of Splitters Single splitter Dual splitter (2) Triple splitter (3) A B C Output Connector/Adapter Singlemode 2U 2A 4U 7U 7A 8A LA LU KU 00 FC ultra polish FC angled polish ST ® ultra polish SC ultra polish SC angled polish E-2000 angled polish LX.5 ® angled polish LX.5 ® ultra polish LC ultra polish Bare fiber Multimode** 2M 2N 5F 5U 9A 9B LM LN PM 00 FC 62.5/125 FC 50/125 ST ® 50/125 ST ® 62.5/125 SC 50/125 SC 62.5/125 LX.5 ® 62.5/125 LX.5 50/125 LC 62.5/125 Bare fiber Multimode** OR 2M 2N 5F 5U 9A 9B LM LN PM 00 FC 62.5/125 FC 50/125 ST ® 50/125 ST ® 62.5/125 SC 50/125 SC 62.5/125 LX.5 ® 62.5/125 LX.5 50/125 LC 62.5/125 Bare fiber Input Connector/Adapter Singlemode FC ultra polish FC angled polish ST ® ultra polish SC ultra polish SC angled polish E-2000 angled polish LX.5 ® angled polish LX.5 ® ultra polish LC ultra polish Bare fiber 2U 2A 4U 7U 7A 8A LA LU KU 00 Standard VAM for FL2000 and non-ADC frames WideVAM ™ for FL2000 WideVAM ™ for non-ADC frames MiniVAM for Next Generation Frames* For OMX ™ 600 frames For LGX-compatible frames VSM- FLVW-S VSMW- NGF-V MXV- VLM- Input Pigtail Length Example (In Meters): 01 = 1 m 10 = 10 m 00 = Adapters only on input and output ports Output Pigtail Length *MiniVAMs are not available with split ratios above 1x8 nor can they be configured with three splitters. They are not available with E-2000 connectors/adapters **VAMs with multimode connectors/adapters can only be configured with 90/10 or uniform split (50/50) ratios. See page 58 for configuration illustrations. Please contact ADC for specifications and available split ratios. 10/03 • 100571 600 mm Products 56 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Value-Added Module System Wavelength Division Multiplexer Modules A Single Module Configuration Catalog Number Mux Port Connector/Adapter 2U 2A 4U 7U 7A 8A LA LU KU 00 FC ultra polish FC angled polish ST ® ultra polish SC ultra polish SC angled polish E-2000 angled polish LX.5 ® angled polish LX.5 ® ultra polish LC ultra polish Bare fiber Demux Port Pigtail Length Configuration VAM Style Unidirectional multiplexer Unidirectional demultiplexer Bidirectional λ 1 Tx/λ 2 Rx Bidirectional λ 1 Rx/λ 2 Tx 45 dB isolation, pass 1310 45 dB isolation, pass 1550 (Dual only) unidirectional multiplexer, unidirectional demultiplexer** (Dual only) bidirectional λ 1 Tx/λ 2 Rx, bidirectional λ 2 Tx/λ 1 Rx A C E G J K L M WDM Type (λ 1 ; λ 2 ) B Dual C Triple 1 Standard Isolation* 2 High 3 Very High Mux Port Pigtail Length Example (In Meters): 01 = 1 m 10 = 10 m 00 = Adapters only on mux and demux ports **WDM Type “L” includes (1) unidirectional multiplexer (standard isolation) and (1) unidirectional demultiplexer (isolation specified by next character) *MiniVAMs are not available with E-2000 connectors/adapters Wavelength 1310 (λ 1 )/1550 (λ 2 ) 1533 (λ 1 )/1557 (λ 2 ) 1310/1533/1557 1550 (λ 1 )/1625 (λ 2 ) 1310 (λ 1 )/1625 (λ 2 ) A B C E F 2 5 MUX front, DEMUX front MUX rear, DEMUX front Standard VAM for FL2000 and non-ADC frames WideVAM ™ for FL2000 WideVAM ™ for non-ADC frames MiniVAM for Next Generation Frames* For OMX ™ 600 frames For LGX- compatible frames WDM- FLVW-W WDMW- NGF-W MXV-W VLM-W Demux Port Connector/Adapter 2U 2A 4U 7U 7A 8A LA LU KU 00 FC ultra polish FC angled polish ST ® ultra polish SC ultra polish SC angled polish E-2000 angled polish LX.5 ® angled polish LX.5 ® ultra polish LC ultra polish Bare fiber In the ordering charts, the abbreviation “mux” references the multiplexed side of the WDM, the side where two optical signals co-exist on one fiber. The abbreviation “demux” references the demultiplexed side of the WDM, the side where each signal appears on its own fiber. Both unidirectional and bidirectional WDMs are available as shown below. 1310 1310 1550 1550 1310 1310 1550 1550 UNIDIRECTIONAL MULTIPLEXER BIDIRECTIONAL TRANSMISSION DEMUX MUX 1310 1310 1550 1550 MUX DEMUX DEMUX MUX 1310 1310 1550 1550 MUX DEMUX UNIDIRECTIONAL DEMULTIPLEXER See page 58 for configuration instructions. Please contact ADC for specifications. 10/03 • 100571 600 mm Products 57 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Value-Added Module System Monitor Modules Catalog Number Input pigtail length Example (in meters): 01 = 1 m 10 = 10 m 000 = Adapters only on input, output and monitor ports Monitor pigtail length Output pigtail length Splitter Ratio** A B C E F H J K 90/10 95/05 50/50 80/20 75/25 70/30 60/40 99/01 Module Style Dual monitor cross-connect with attenuator*** Customer premises Dual monitor cross-connect Dual monitor cross-connect 1 B D J Output Connector Type Singlemode 2U 2A 4U 7U 7A 8A LA LU KU 00 FC ultra polish FC angled polish ST ® ultra polish SC ultra polish SC angled polish E-2000 angled polish LX.5 ® angled polish LX.5 ® ultra polish LC ultra polish Bare fiber 2M 2N 5F 5U 9A 9B LM LN PM 00 FC 62.5/125 FC 50/125 ST ® 50/125 ST ® 62.5/125 SC 50/125 SC 62.5/125 LX.5 ® 62.5/125 LX.5 ® 50/125 LC 62.5/125 Bare fiber Multimode** Monitor Connector Type Singlemode 2U 2A 4U 7U 7A 8A LA LU KU 00 FC ultra polish FC angled polish ST ® ultra polish SC ultra polish SC angled polish E-2000 angled polish LX.5 ® angled polish LX.5 ® ultra polish LC ultra polish Bare fiber OR OR 2M 2N SF 5U 9A 9B LM LN PM 00 FC 62.5/125 FC 50/125 ST ® 50/125 ST ® 62.5/125 SC 50/125 SC 62.5/125 LX.5 ® 62.5/125 LX.5 ® 50/125 LC 62.5/125 Bare fiber Multimode** Input Connector Type Singlemode VAM Style 2U 2A 4U 7U 7A 8A LA LU KU 00 FC ultra polish FC angled polish ST ® ultra polish SC ultra polish SC angled polish E-2000 angled polish LX.5 ® angled polish LX.5 ® ultra polish LC ultra polish Bare fiber OR 2M 2N 5F 5U 9A 9B LM LN PM 00 FC 62.5/125 FC 50/125 ST ® 50/125 ST ® 62.5/125 SC 50/125 SC 62.5/125 LX.5 ® 62.5/125 LX.5 ® 50/125 LC 62.5/125 Bare fiber Multimode** 1 2 3 1 circuit 2 circuits 3 circuits Number of Circuits per VAM *** This style cannot be used in NGF-M modules. Standard VAM for FL2000 and non-ADC frames WideVAM ™ for FL2000 WideVAM ™ for non-ADC frames MiniVAM for Next Generation Frames* For OMX ™ 600 frames For LGX- compatible frames VMM- FLVW-M VMMW- NGF-M MXV-M VLM-M *MiniVAMs are not available with E-2000 connectors/adapters **VAMs with multimode connectors/adapters can only be configured with 90/10 or uniform split (50/50) ratios. See page 58 for configuration illustrations. Please contact ADC for specifications and available split ratios. 10/03 • 100571 600 mm Products 58 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Value-Added Module System IN OUT REAR FRONT Connectorized pigtail to OSP port on the fiber frame Adapter to attach patch cord or pigtail to OSP port Adapter to attach patch cord to equipment SPLITTER COMPONENTS Connectorized pigtail (3 mm jacketed) to equipment or to port on frame Stub fiber input spliced to equipment or OSP fibers (2 mm jacketed) 2 IN OUT FRONTREAR OUTPUT INPUT OUTPUT Input Front, Output Front 1 x N IN OUT Input Rear, Output Front 5 REAR FRONT OUTPUT OUTPUT INPUT 1 x N Mux Rear, Demux Front 5 REAR FRONT 2 FRONTREAR Demux Mux Demux Demux Demux Mux Mux Front, Demux Front WDM WDM Dual Monitor Cross-Connect D Tx Rx Tx MON Rx MON Tx Rx SPLITTER 90% 10% SPLITTER 90% 10% Customer Premises Monitor Module B SRC Rx CUST MON SRC MON CUST Rx SRC Tx CUST Tx 1 x 2 SPLITTER A 1 x 2 SPLITTER B XX% XX% XX% XX% Dual Monitor Cross-Connect with Variable Attenuator 1 Tx Rx Mon Tx Mon Tx Rx 1 x 2 1 x 2 Rx VAR ATTN Dual Monitor Cross-Connect J Tx Mon Tx Mon Rx Rx Rx SRC Tx SRC 1 x 2 1 x 2 Splitter Modules WDM Modules Monitor Modules REAR FRONT Connectorized pigtail Adapter port Adapter port WDM Connectorized pigtail (3 mm jacketed) Bare pigtail (2 mm jacketed) 10/03 • 100571 600 mm Products 59 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Bulkhead Plates and Blanks ADC ADC ADC ADC VAM-BLNK VAM-6PBX Description Blank plate Six position bulkhead plates loaded with: Singlemode FC adapters FC angled polish adapters ST ® adapters SC adapters SC angled polish adapters (3) duplex SC adapters E-2000 angled polish APC adapters Multimode ST ® adapters SC adapters (3) duplex SC adapters Catalog Number* VAM-BLNK VAM-6PB2 VAM-A6PB2 VAM-6PB4 VAM-6PB7 VAM-A6PB5 VAM-D6PB7 VAM-A6PB8 VAM-6PB5 VAM-6PB9 VAM-D6PB9 Ordering Information Terminators Terminator plugs should be ordered for each unterminated leg on ultra polish adapter ports. For configurations with pigtails an adapter is also required. Description FC connector ST ® connector SC connector Catalog Number FOC-TERMFC-P FOC-TERMST-P FOC-TERMSC-P Ordering Information * These products are available in black; for this option, simply add “-BK” to the end of the catalog number. Please contact the Technical Assistance Center with any questions. Value-Added Module System 10/03 • 100571 600 mm Products 60 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Singlemode Wideband Optical Splitter Specifications Other splitter configurations are available. Please call ADC Technical Assistance Center. 2000 2100 2200 2300 2350 2400 2500 2600 2700 2800 2900 2950 2030 3900 4900 5300 6000 7000 8000 9000 A110 B111 C112 D113 E114 F115 G116 M132 1x2 1x2 1x2 1x2 1x2 1x2 1x2 1x2 1x2 1x2 1x2 1x2 2x2 1x3 1x4 1x5 1x6 1x7 1x8 1x9 1x10 1x11 1x12 1x13 1x14 1x15 1x16 1x32 50/50 55/45 60/40 65/35 66.6./33.3 70/30 75/25 80/20 85/15 90/10 95/5 99/1 50/50 33/33/33 25/25/25/25 20/20/20/20/20 16.6/16.6/ . . . 16.6 14.3/14.3/ . . . /14.3 12.5/12.5/ . . .12.5 11.1/11.1/ . . . /11.1 10/10/10 . . . /10 9.1/9.1/ . . . /9.1 8.3/8.3/ . . . /8.3 7.7/7.7/ . . . /7.7 7.14/7.14/ . . . /7.14 6.66/6.66/ . . . /6.66 6.25/6.25/ . . . 6.25 3.13/3.13/ . . . 3.13 3.7/3.7 3.2/4.1 2.7/4.7 2.3/5.3 2.2/5.5 2.0/6.0 1.6/6.8 1.3/7.8 1.0/9.2 .8/11.2 .5/14.4 0.3/22.5 3.7/3.7 5.9/5.9/5.9 7.4/7.4/7.4/7.4 8.6/8.6/8.6/8.6/8.6 9.8/9.8/9.8/ . . ./9.8 10.6/10.6/ . . . /10.6 11.3/11.3/ . . . /11.3 11.5/11.5/ . . . /11.5 12.1/12.1/ . . . /12.1 13.1/13.1/ . . . /13.1 13.3/13.3/ . . . /13.3 13.8/13.8/ . . . /13.8 13.8/13.8/ . . . /13.8 14.5/14.5/ . . . /14.5 14.9/14.9/ . . . 14.9 18.5/18.5/ . . . 18/5 3.1/3.1 2.7/3.6 2.3/4.1 2.0/4.7 1.9/5.0 1.7/5.4 1.4/6.2 1.1/7.1 .8/8.4 .6/10.2 .4/13.2 NA/NA 3.1/3.1 5.0/5.0/5.0 6.2/6.2/6.2/6.2 7.3/7.3/7.3/7.3/7.3 8.1/8.1/8.1 . . . /8.1 8.9/8.9/ . . . /8.9 9.5/9.5/ . . ./9.5 9.9/9.9/ . . . /9.9 10.4/10.4/ . . . /10.4 10.9/10.9/ . . . /10.9 11.3/11.3/ . . . /11.3 11.6/11.6/ . . . /11.6 11.8/11.8/ . . . /11.8 12.4/12.4/ . . . /12.4 12.6/12.6/ . . . 12.6 15.8/15.8/ . . . 15.8 Splitter Number Splitter Type Splitter Ratio Maximum Insertion Loss* Typical Insertion Loss* * Does not include connector losses. See table on the following page or contact the ADC Technical Assistance Center. Maximum Insertion Loss Maximum insertion loss is the upper limit of insertion loss for the coupler and applies over the entire wavelength range specified in the bandpass. Typical Insertion Loss Typical insertion loss is the expected insertion loss value for the coupler measured at the specified center wavelength (i.e. 1310 nm and/or 1550 nm). Value-Added Module System 10/03 • 100571 600 mm Products 61 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 MATERIAL Fiber: Jacket: Housing: OPTICAL Bandpass Wavelength 1: Wavelength 2: Directivity: Reflectance: Polarization Stability: MECHANICAL Cable Retention: Flex: Twist: Vibration: Impact: Flammability: ENVIRONMENTAL Humidity: Thermal Aging: Temperature Cycling: Corning SMF-28 0.900 mm hytrel tube Stainless steel tube 1260/1360 nm 1430/1580 nm 55 dB minimum < -55 dB .5 dB maximum .45 kg (1.0 lb.) maximum for .25 mm and .900 mm fiber, 1 kg (2.2 lbs.) maximum for cabled fiber assemblies 300 cycles; .45 kg (1.0 lb.) maximum load (fiber cable only) 100 cycles; .45 kg (1.0 lb.) maximum load (fiber cable only) 10-55 Hz per FOTP II condition I 8 drops from 1.5 meters All materials used in fabrication of coupler housing meet UL 94, Level V-I requirements 336 hours, 60°C at 95% relative humidity 336 hours, 85°C 336 hours, -40°C to 85°C Singlemode Optical Splitter Specifications Value-Added Module System Singlemode Optical Connector Specifications Ultra Polish PC Connectors Angled Polish Connectors INSERTION LOSS (dB) 0.3 dB maximum 0.1 dB typical 0.5 dB maximum 0.1 dB typical RETURN LOSS (dB) 57 dB minimum 65 dB minimum 10/03 • 100571 600 mm Products 62 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Singlemode WDM Specifications MATERIAL Fiber: Corning SMF-28 Jacket: 0.900 mm OPTICAL Uniformity: 1.0 Log2N (where N = number of channels) Polarization Stability: 0.5 dB maximum Bandpass: (see table below) Insertion Loss: (see table below) Reflectance: < -55 dB Isolation Near End: 55 dB Far End: (see table below) MECHANICAL Cable Retention: Flex: 45 kg (1.0 lb.) maximum for .250 mm and .900 mm fiber; Twist: 1.0 kg (2.2 lbs.) maximum for cabled fiber assemblies Vibration: 10-55 Hz per FOTP II condition I Impact: 100 cycles; 8 drops from 1.5 meters Flammability: All materials used in fabrication of the coupler housing meet UL 94, Level V-I requirements ENVIRONMENTAL Humidity Resistance: 336 hours, 60°C at 95% relative humidity Thermal Aging: 336 hours, 85°C Temperature Cycling: 336 hours, -40°C to 85°C Multiplexer/Demultiplexer: High Isolation Demultiplexer: Very High Isolation Demultiplexer: Wavelength Filters: 1310/1550 nm MAXIMUM INSERTION LOSS* (dB) 0.3 0.7 1.0 0.3 MINIMUM ISOLATION (dB) 15 30 45 15 PASSBAND (nm) 1310 ± 20 nm and 1550 ± 20 nm 1310 ± 20 nm and 1550 ± 20 nm 1310 ± 20 nm and 1550 ± 20 nm 1310 ± 20 nm and 1550 ± 20 nm Unidirectional Multiplexer: High Isolation Undirectional Multiplexer or Bidirectional Multiplexer/Demultiplexer: Very High Isolation Undirectional Multiplexer or Bidirectional Multiplexer/Demultiplexer: Filter Passing 1533 nm: Filter Passing 1557 nm: 1533/1557 nm MAXIMUM INSERTION LOSS* (dB) 0.9 1.8 2.1 0.9 0.9 MINIMUM ISOLATION (dB) N/A 20 35 13 13 PASSBAND (nm) 1533 ±3 and 1557 ±3 nm 1533 ±3 and 1557 ±3 nm 1533 ±3 and 1557 ±3 nm 1533 ±3 nm 1557 ±3 nm * Maximum Insertion Loss does not include connector loss. Value-Added Module System [...]... trumpet sliding radius limiter Other mounting styles cannot be used in 40 mm recess applications 2 • +32-2-712-65-42 65 Fiber Management Tray 1 Rack Unit – Termination and Storage The termination and storage tray terminates and stores 12, 16, or 24 fibers in an all-front-access design This tray mounts in 19-inch, 23-inch, or ETSI racks, while sliding radius limiters provide cable management for incoming and... Micro Value-Added Module System MicroVAM Shown in Access Position FMT-G Series with MicroVAM Ordering Information Catalog Number Description 2 RU Fiber Management Tray (FMT-G Series) accommodates up to 12 MicroVAMs for monitoring optical signals FMT-GVM00000-A72P Ordering Information for Micro Value-Added Modules follows on the next page 10/03 • 100571 600 mm Products The 2RU FMT Value-Added Module. .. 63 Fiber Management Tray 1 Rack Unit – Termination Only 10/03 • 100571 600 mm Products The termination-only fiber management tray provides termination for 24 or 32 fibers in an all-front-access design This tray mounts in 19-inch, 23-inch, or ETSI racks Sliding radius limiters provide cable management for incoming and outgoing fibers 32-Termination Only 24-Termination Only Catalog Number FMT-D 0 ... 1 Rack Unit – Termination and Splice 10/03 • 100571 600 mm Products The termination and splice tray terminates and splices 12, 16, or 24 fibers in an all-front-access design This tray mounts in 19-inch, 23-inch, or ETSI racks Sliding radius limiters provide cable management for incoming and outgoing fibers Panels loaded with pigtails come with color-coded 900 micron pigtails 12-Termination/Splice (right... The 2RU FMT Value-Added Module (VAM) chassis houses up to twelve MicroVAMs These MicroVAMs are used for testing and monitoring optical signals; technicians can access both directions of the signal without disrupting service www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 77 Fiber Management Tray 2 Rack Unit – Micro Value-Added Module System Monitor Module Ordering Information Catalog Number 10/03 • 100571... termination-only fiber management tray provides termination for 72 fibers in an all-front-access design This tray mounts in 19-inch, or ETSI racks Sliding radius limiters provide cable management for incoming and outgoing fibers www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 73 Fiber Management Tray 2 Rack Unit – Termination with IFC or Multifiber Cable 10/03 • 100571 600 mm Products The termination-only... 100571 These trays are lockable, further ensuring the integrity of the fibers by greatly reducing the chance for accidents Modular Design 10/03 • The value of a single interface for performing multiple tasks in your network cannot be denied By employing a one-rack-unit modular tray, network technicians have ready access to terminating, splicing, and storing fiber This one-stop management approach means... and increase network operations costs Sliding adapter packs allow easy access for connecting jumpers and cleaning connectors, ensuring that any fiber can be installed or removed without inducing a macrobend on an adjacent fiber That can mean the difference between a network reconfiguration time of 20 minutes per fiber and one of over 90 minutes per fiber 100571 These trays are lockable, further ensuring... www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 74 Fiber Management Tray 2 Rack Unit – Termination and Splice The termination and splice tray terminates and splices 48 fibers in an all-front-access design This tray mounts in 19-inch, or ETSI racks Sliding radius limiters provide cable management for incoming and outgoing fibers Panels loaded with pigtails come with color-coded 900 micron pigtails Catalog... management by addressing one of the most critical elements of fiber cable management: bend radius protection As fibers leave the tray, a specially designed bell-shaped exit point provides maximum edge protection By controlling the movement of fibers within the tray, error-proof slack loop management is maintained, ensuring 30 mm bend radius protection within the tray This is crucial in ensuring no fiber breaks, . x 30.48 cm) Ordering Information 3.5-Inch Chassis – 4 Single Plug -In Modules The 3.5-inch VAM chassis fits into any 19-inch rack mounting environment 30.48 cm) Ordering Information 1.75-Inch Chassis – 2 Single Plug -In Modules The 1.75-inch VAM chassis fits into any 19-inch rack mounting environment.

Ngày đăng: 24/01/2014, 11:20

TỪ KHÓA LIÊN QUAN