Đang tải... (xem toàn văn)
Tài liệu Shop Manual & ETM BCM KIA Cerato 2010
2010 > G 1.6 DOHC > Body Electrical System Component Location1. Windshield wiper arm & blade2. Wiper & washer switch3. Windshield washer hose5. Washer motor6. Washer reservoir7. Wiper relay (Engine room relay box)Language 4. Windshield wiper motor & linkage 2010 > G 1.6 DOHC > Body Electrical System Removal1. Disconnect the negative (-) battery terminal.2. Remove the steering column upper(A) and lower (B) shrouds after loosening 3 screws.Language 3. Remove the wiper switch (A) with pushing the lock pin (C) after disconnecting the connector (B).[LHD][RHD] Installation1. Install the windshield wiper switch.2. Connect the wiper switch connector.3. Install the steering column upper and lower shrouds.InspectionCheck for continuity between the terminals while operating the wiper and washer switch. If it is not normal condition, replace wiper and wiper switch.Wiper Switch Washer Switch 2010 > G 1.6 DOHC > Body Electrical System Component LocationLanguage 1. Cap2. Nut3. Wiper arm & blade4. Retainer5. Cowl top cover6. Bolt7. Wiper motor & linkage assembly8. Wiper motor connector 2010 > G 1.6 DOHC > Body Electrical System Removal1. Remove the windshield wiper arm and blade after removing a nut (A) and wiper cap (B).2. Remove the weather strip and the cowl top cover (A) after removing retainers.3. Remove the windshield wiper motor and linkage assembly(B) after removing 2 bolts. Disconnect the wiper motor connector (A) from the wiper motor & linkage assembly.Language Installation1. Install the wiper motor and linkage assembly and then connect the wiper motor connector.TORQUE : 7-11Nm (0.7-1.1, kgf.m, 5.0-7.9 lbf.ft)2. Install the cowl top cover.3. Install the windshield wiper arm and blade.TORQUE : 22.5~26.4 Nm (2.3~2.7 kgf.m, 16.6~21.7 lbf.ft)- The windshield wiper motor must be cycled to make sure that it is in the park position.If necessary, adjust the wiper arm and blade.4. Install the wiper arm and blade to the specified position.SpecifiedpositionADistance[in (mm)]1.18~1.37(30~35) 5. Set the cowl top cover on the specified spray position.SpecifiedpositionDistance (in)A 15.7B 1.13C 2.96D 13.8E 6.4F 7.14G 12.88H 16.15InspectionSpeed Operation Check 1. Remove the connector from the wiper motor.1. Low, 2. GND, 3. High4. Parking, 5. IGN +, 6. -2. Attach the positive (+) lead from the battery to terminal 6 and the negative (-) lead to terminal 5.3. Check that the motor operates at low speed.4. Connect the positive (+) lead from the battery to terminal 4 and the negative (-) lead to terminal 5.5. Check that the motor operates at high speed.Automatic Stop Operation Check1. Operate the motor at low speed using the stalk control.2. Stop the motor operation anywhere except at the off position by disconnecting terminal 1.3. Connect terminals 4 and 1.4. Connect the positive (+) lead from the battery to terminal 5 and the negative (-) lead to terminal 2.5. Check that the motor stops running at the off position. . 2010 > G 1.6 DOHC > Body Electrical System Component Location1. Windshield wiper arm & blade2. Wiper & washer switch3. Windshield. box)Language 4. Windshield wiper motor & linkage 2010 > G 1.6 DOHC > Body Electrical System Removal1. Disconnect the negative (-) battery terminal.2.