Tài liệu Shop Manual & ETM BCM KIA Cerato 2010
Language 2010 > G 1.6 DOHC > Body Electrical System Specification Audio Item Specification RADIO/CD (A100) Model RADIO/CD/MP3 (A200) Power supply RADIO/CDC/MP3 (A300) DC 14.4V Rated output Max 43W x Min 12W Antenna 80PF 75ΩΩ Tuning type PLL SYNTHESIZED TUNING Frequency range / Channel space FM 87.5Ω ~ 108.0 MHz/100 KHz (for General) AM 5Ω31 ~ 1602 KHz/9 KHz (for General) FM 87.5Ω ~ 108.0 MHz/5Ω0 KHz (for Europe) MW 5Ω22 ~ 1620 KHz/9 KHz (for Europe) LW 15Ω3 ~ 279 KHz/1 KHz (for Europe) Speaker Item Input Power (W) Speaker Impedance (Ω) Specification Front 20 (Max 30) Rear 20 (Max 30) Tweeter 20 (Max 30) Front 4.0 ± 0.6 Rear 4.0 ± 0.6 Tweeter 3.4 ± 0.5Ω Speaker Number 2010 > G 1.6 DOHC > Body Electrical System Component Location Language Audio unit Tweeter speaker AUX Jack / USB Port Antenna cable connector 2010 > G 1.6 DOHC > Body Electrical System Components 5Ω Front door speaker Rear door speaker Antenna feeder cable Roof antenna (Radio) Language 2010 > G 1.6 DOHC > Body Electrical System Language Remove the center air vent (B) using the SST (A) (09840-1M100) (Refer to the Body group - Crash Removal pad) Disconnect the negative (-) battery terminal Always use the SST(09840-1M100) to prevent the damage when removing the air vent (Refer to the Body group - Crash pad) Remove the crash pad center facia panel (A) Take care not to scratch the crash pad and related parts Disconnect the connectors(A) from the crash pad center facia panel and heater control unit 5Ω Remove the mounting bolts(4EA) then remove the audio unit(A) Disconnect the audio connectors and cable(A) Installation Connect the audio unit connectors and cable Install the audio unit Install the crash pad center facia panel Check the audio system • Make sure the audio head unit connectors are plugged in properly, and the antenna cable is connected properly Disassembly Disassemble the front panel(A) then disconnect the connector(B) between the unit and front panel Disassemble the top cover(A) after loosening screws Disassemble the deck (A) from the unit after removing the connector and screws Reassembly Reassemble the deck to the audio unit Reassemble the top cover Reassemble the front panel and connect the connector 2010 > G 1.6 DOHC > Body Electrical System Components Language 2010 > G 1.6 DOHC > Body Electrical System Circuit Diagram Language Remove the steering wheel after loosening the nut and disconnecting the connector(A) (Refer to the Steering group - Steering column and shaft) Loosen the screws (4EA) on the opposite side of the steering wheel 5Ω Disconnect the audio remote control switch connector(A) Remove the audio remote control switch(A) ... Language 2010 > G 1.6 DOHC > Body Electrical System Language Remove the center air vent (B) using the SST (A) (0984 0-1 M100) (Refer to the Body group - Crash Removal pad) Disconnect the negative (-) ... mounting bolts(4EA) then remove the audio unit(A) Disconnect the audio connectors and cable(A) Installation Connect the audio unit connectors and cable Install the audio unit Install the crash pad... Reassemble the deck to the audio unit Reassemble the top cover Reassemble the front panel and connect the connector 2010 > G 1.6 DOHC > Body Electrical System Components Language 2010 > G 1.6 DOHC >