Tài liệu Shop Manual & ETM BCM KIA Cerato 2010
2010 > G 1.6 DOHC > Body Electrical System Component Location1. ICM relay box (Door lock/unlock relay)2. Body control module (BCM)3. Front door lock actuator & switch4. Rear door lock actuator & switch6. Door lock knob7. Door lock switch8. Passenger compartment junction box(Trunk lid relay)Language 5. Trunk lid actuator & switch 2010 > G 1.6 DOHC > Body Electrical System InspectionFront Door Lock Actuator1. Remove the front door trim.(Refer to the Body group - Front door)2. Remove the front door module.(Refer to the Body group - Front door).3. Disconnect the connectors from the actuator.[LHD][RHD]Language 4. Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.Rear Door Lock Actuator1. Remove the rear door trim.(Refer to the Body group - Rear door)2. Remove the rear door module.(Refer to the Body group - Rear door)3. Disconnect the connectors from the actuator.[LHD] [RHD]4. Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily. Trunk lid Lock Actuator Inspection1. Remove the trunk trim. (Refer to the Body group - trunk)2. Disconnect the 3P connector from the actuator.3. Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.Front Door Lock Switch1. Remove the front door trim.(Refer to the Body group - Front door)2. Remove the front door module.(Refer to the Body group - Front door).3. Disconnect the connectors from the actuator.[LHD] [RHD]4. Check for continuity between the terminals in each switch position when inserting the key into the door according to the table.Rear Door Lock Switch1. Remove the rear door trim.(Refer to the Body group - Rear door) 2. Remove the rear door module.(Refer to the Body group - Rear door)3. Disconnect the connectors from the actuator.[LHD][RHD]4. Check for continuity between the terminals in each switch position according to the table. Trunk lid Switch1. Remove the trunk trim. (Refer to the Body group - Trunk)2. Disconnect the 3P connector from the actuator.3. Check for continuity between the terminals in each switch position according to the table. 2010 > G 1.6 DOHC > Body Electrical System InspectionLanguage Door Lock1. Disconnect the negative (-) battery terminal.2. Remove the ICM relay box.3. Check for continuity between the terminals.4. There should be continuity between the No.5 terminal and No.4 terminals in the ICM-B when power and ground are connected to the No.11 terminal and No.13 terminal in the ICM-B.5. There should be no continuity between the No.5 terminal and No.14 terminal in the ICM-B when power is disconnected.Door Unlock1. Disconnect the negative (-) battery terminal.2. Remove the ICM relay box.3. Check for continuity between the terminals.4. There should be continuity between the No.4 terminal and No.14 terminal in the ICM-B when power and ground are connected to the No.10 terminal and No.13 terminal in the ICM-B.5. There should be no continuity between the No.4 terminal and No.14 terminal in the ICM-B when power is disconnected. Trunk Open1. Disconnect the negative (-) battery terminal.2. Remove the passenger compartment junction box.3. Check for continuity between the terminals.4. There should be continuity between the No.3 terminal in the I/P-H and the No.2 terminal in the I/P-D when power and ground are connected to the No.3 terminal in the I/P-H and the No.28 terminal in the I/P-F.5. There should be no continuity between the No.3 terminal in the I/P-H and the No.2 terminal in the I/P-D when power and ground are connected to the No.3 terminal in the I/P-H and the No.28 terminal in the I/P-F. 2010 > G 1.6 DOHC > Body Electrical System InspectionLanguage [...]...Driver Door Lock Switch 1 Disconnect the negative (-) battery terminal 2 Remove the front door trim and power window switch (Refer to the Body group - "front door" ) [LHD] [RHD] 3 Remove the power window switch module after removing the screws Be careful not to damage the hooks when removing the switch... module after removing the screws Be careful not to damage the hooks when removing the switch modul 4 Check for continuity between the terminals in each switch position according to the table [Auto Up & Down] [Auto Down] . momentarily.Front Door Lock Switch1. Remove the front door trim.(Refer to the Body group - Front door) 2. Remove the front door module.(Refer to the Body group - Front door) .3.. terminal.2. Remove the front door trim and power window switch. (Refer to the Body group - "front door& quot;)[LHD][RHD]3. Remove the power window switch module