Drill 1 OSG

PRODUCT INFORMATION PRODUCT INFORMATION TOOL COMMUNICATION Cutting Data TOOL COMMUNICATION PRODUCT INFORMATION Selection Chart Vol NEW SIZES Selection chart Diamond Drill Series 20 15 10 10 50 5,000 100 200 10,000 300 400 15,000 500 20,000 600 800 1,000 1,056 25,000 10 Safe use of cutting tools 3,312 6,624 11,592 14,904 Use a safety cover,safety glasses and safety shoes during operation 24,840 Do not touch cutting edges with bare hands Do not touch cutting chips with bare hands.Chips will be hot after cutting Stop cutting when the tool becomes dull Stop cutting operation immediately if you hear any strange cutting sounds Do not modify tools Check hole after drilling Tool specifications subject to change without notice 1,000 1,500 2,000 2,500 3,000 1 1 1 1 1 1 1 1 1 0533-82-1134 Features 3-22 Honnogahara, Toyokawa, Aichi 442-8543 Japan Tel +81-533-82-1118 Fax +81-533-82-1136 E-mail:cs-info@osg.co.jp 1 1 500 For aluminum alloy with high silicon content 1 1 1 1 1 1 1 1 1 When drilling aluminum alloy with high silicon content, this diamond drill has a longer tool life than a comparable carbide drill hp-info@osg.co.jp The drill's edges are not subject to welding when drilling aluminum alloy E-mail :cs-info@osg.co.jp Trademark of American Soybean Association The chisel edges of the OSG Diamond drill are made of PCD Thanks to the unique point design, the PCD-GDN can perform at high speeds D-GDN employs a diamond coating PRODUCT INFORMATION TOOL COMMUNICATION Specification Chart PRODUCT INFORMATION TOOL COMMUNICATION Specification Chart PCD Helix Twist Drill for Aluminum Alloy with high silicon content Recommended Drilling Conditions Diamond Coated Carbide Drills Thanks to specially selected PCD(polycrystalline diamond), PCD-GDN has high wear resistance that extends its tool life PRODUCT INFORMATION Wide range of sizes (from1 to 12mm) with 0.1mm incrementally TOOL COMMUNICATION PRODUCT INFORMATION TOOL COMMUNICATION Specification Chart PRODUCT INFORMATION TOOL COMMUNICATION Specification Chart PCD Helix Twist Drill for Aluminum Alloy with high silicon content Recommended Drilling Conditions Diamond Coated Carbide Drills Thanks to specially selected PCD(polycrystalline diamond), PCD-GDN has high wear resistance that extends its tool life PRODUCT INFORMATION Wide range of sizes (from1 to 12mm) with 0.1mm incrementally TOOL COMMUNICATION PRODUCT INFORMATION TOOL COMMUNICATION Specification Chart PRODUCT INFORMATION TOOL COMMUNICATION Specification Chart PCD Helix Twist Drill for Aluminum Alloy with high silicon content Recommended Drilling Conditions Diamond Coated Carbide Drills Thanks to specially selected PCD(polycrystalline diamond), PCD-GDN has high wear resistance that extends its tool life PRODUCT INFORMATION Wide range of sizes (from1 to 12mm) with 0.1mm incrementally TOOL COMMUNICATION PRODUCT INFORMATION PRODUCT INFORMATION TOOL COMMUNICATION Cutting Data TOOL COMMUNICATION PRODUCT INFORMATION Selection Chart Vol NEW SIZES Selection chart Diamond Drill Series 20 15 10 10 50 5,000 100 200 10,000 300 400 15,000 500 20,000 600 800 1,000 1,056 25,000 10 Safe use of cutting tools 3,312 6,624 11,592 14,904 Use a safety cover,safety glasses and safety shoes during operation 24,840 Do not touch cutting edges with bare hands Do not touch cutting chips with bare hands.Chips will be hot after cutting Stop cutting when the tool becomes dull Stop cutting operation immediately if you hear any strange cutting sounds Do not modify tools Check hole after drilling Tool specifications subject to change without notice 1,000 1,500 2,000 2,500 3,000 1 1 1 1 1 1 1 1 1 0533-82-1134 Features 3-22 Honnogahara, Toyokawa, Aichi 442-8543 Japan Tel +81-533-82-1118 Fax +81-533-82-1136 E-mail:cs-info@osg.co.jp 1 1 500 For aluminum alloy with high silicon content 1 1 1 1 1 1 1 1 1 When drilling aluminum alloy with high silicon content, this diamond drill has a longer tool life than a comparable carbide drill hp-info@osg.co.jp The drill's edges are not subject to welding when drilling aluminum alloy E-mail :cs-info@osg.co.jp Trademark of American Soybean Association The chisel edges of the OSG Diamond drill are made of PCD Thanks to the unique point design, the PCD-GDN can perform at high speeds D-GDN employs a diamond coating PRODUCT INFORMATION PRODUCT INFORMATION TOOL COMMUNICATION Cutting Data TOOL COMMUNICATION PRODUCT INFORMATION Selection Chart Vol NEW SIZES Selection chart Diamond Drill Series 20 15 10 10 50 5,000 100 200 10,000 300 400 15,000 500 20,000 600 800 1,000 1,056 25,000 10 Safe use of cutting tools 3,312 6,624 11,592 14,904 Use a safety cover,safety glasses and safety shoes during operation 24,840 Do not touch cutting edges with bare hands Do not touch cutting chips with bare hands.Chips will be hot after cutting Stop cutting when the tool becomes dull Stop cutting operation immediately if you hear any strange cutting sounds Do not modify tools Check hole after drilling Tool specifications subject to change without notice 1,000 1,500 2,000 2,500 3,000 1 1 1 1 1 1 1 1 1 0533-82-1134 Features 3-22 Honnogahara, Toyokawa, Aichi 442-8543 Japan Tel +81-533-82-1118 Fax +81-533-82-1136 E-mail:cs-info@osg.co.jp 1 1 500 For aluminum alloy with high silicon content 1 1 1 1 1 1 1 1 1 When drilling aluminum alloy with high silicon content, this diamond drill has a longer tool life than a comparable carbide drill hp-info@osg.co.jp The drill's edges are not subject to welding when drilling aluminum alloy E-mail :cs-info@osg.co.jp Trademark of American Soybean Association The chisel edges of the OSG Diamond drill are made of PCD Thanks to the unique point design, the PCD-GDN can perform at high speeds D-GDN employs a diamond coating  ... + 81- 533-82 -11 18 Fax + 81- 533-82 -11 36 E-mail:cs-info @osg. co.jp 1 1 500 For aluminum alloy with high silicon content 1 1 1 1 1 1 1 1 1 When drilling aluminum alloy with high silicon content, this diamond drill. .. + 81- 533-82 -11 18 Fax + 81- 533-82 -11 36 E-mail:cs-info @osg. co.jp 1 1 500 For aluminum alloy with high silicon content 1 1 1 1 1 1 1 1 1 When drilling aluminum alloy with high silicon content, this diamond drill. .. after drilling Tool specifications subject to change without notice 1, 000 1, 500 2,000 2,500 3,000 1 1 1 1 1 1 1 1 1 0533-82 -11 34 Features 3-22 Honnogahara, Toyokawa, Aichi 442-8543 Japan Tel + 81- 533-82 -11 18