Centum VP maintenance training part2

June 2012 Yokogawa Electric Corporation YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Maintenance Course Yokogawa Vietnam Co Ltd Service Department YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Maintenance Course Schedule for the day: Session Starts: 9:00 – 10:30 am Tea Break: 10:30 – 10:45 am Lunch: 12:00 – 1:00 pm Session Resume: YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT 1:00 – 3:00 Tea Break: 3:00 – 3:15 pm Sessions Ends: 5:00 pm pm Agenda CENTUM VP Maintenance Course Day Software compatibility Hardware setup prior to installation Software Environment Window set-up prior to installation (Vista/W7/Server) Centum VP installation Hands-on Exercises YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Software compatibility Software Name Version Microsoft Exel 2007, 2010 Microsoft Word 2007, 2010 Microsoft Visual Studio 2008+SP1 Microsoft Internet Explorer 8.0/9.0 APC PowerChute Business Edition 8.01 Symantec Endpoint Protection 11.0 McAfee Virus Scan Enterprise 8.07i Adobe Reader 9.4 Adobe Acrobat 10.1 YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Remarks Use with the report package and setting for FCS data setting/ acquisition package (Picot) Use with electronic Document package Hardware Installation Hardware Setup Prior to Installation YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Hardware Setup It is necessary to set domain and station numbers for the following switches before installing the software: • Vnet/IP interface card (VI701) • Field control station processor module (CP451) • Vnet Router (AVR10D) When the domain number and station number are correctly defined and the Unshielded Twisted Pair Cables (UTP) are properly connected, the SND and RCV lamps turn on at power-on If the RCV lamp turns on while the SND lamp does not, check the dip switch setting of the corresponding card YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Vnet/IP Interface Card • RDY lamp This lamp illuminates to indicate that the card is working properly as the result of the periodic diagnosis • RCV lamp This lamp illuminates when a signal is received through Vnet/IP • SND lamp This lamp illuminates when a signal is sent through Vnet/IP • Ethernet connectors These connectors are used for connecting with the Layer2 Switch The connector type is RJ45 and the twist-pair cable type is CAT5e YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Page.8 Installing the Vnet/IP Interface Card to a PC The Vnet/IP interface card (VI701) is installed in the expansion PCI slot of a general purpose personal computer (PC/AT compatible) The VI701 connects the computer to the Vnet/IP Installation Procedure: Set the station address of VI701 interface card Turn off the power of the PC For safety, remove the power plug from the power outlet Loosen the screws of the PCI slot cover and remove the slot cover Insert the VI701 interface card in the PCI slot and make sure that the card is inserted straightly in the slot Tighten the screws of the PCI slot cover so as to fix the VI701 card Remove Procedure: Turn off the power of the PC Disconnect the cables for BUS1 and BUS2 from the VI701 card For replacement of VI701 card, there is no need to disconnect the cables from the Layer2 Switch Connect the card with Layer2 Switch with the cables for BUS1 and BUS2 For this connection, there is no need to turn off the power of the Layer2 Switch Turn on the power of the PC Confirm that the RDY lamp on VI701 card is on Write the station address to the sticker that comes with the VI701 and stick it on the front of the computer or another obvious place YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Remove the VI701 from the PCI slot Setting Vnet/IP Station Address – VI701 The station address of a Vnet/IP is defined by a combination of a domain number and a station number The DIP switches for setting the domain number and station number are located on the printed circuit board of the VI701 YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Overview of License Management License project is created in the license manager HIS license are defined in the license project Licenses are then deployed to each individual HIS HIS must accept these licenses YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Overview of License Management Licenses are assigned to the following three stations:  License-assigned Stations Are assigned licenses for the CENTUM VP software package installed on the license-assigned stations  License Management Station Is assigned licenses for the CENTUM VP software packages installed on the license management station itself  FCS Are assigned licenses for the Options software used in FCS YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Overview of License Management After assigning licenses, distribute the licenses to the stations At this point, the licenses that have been assigned to each station are distributed as follow:  Licenses assigned to license-assigned Stations Distributed from the license management station to the relevant license-assigned station  Licenses assigned to License Management Station Distributed from the license management station to itself  Licenses assigned to an FCS License assigned to an FCS are distributed to the HIS installed with system builders YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Creating license Project YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Create a new license project Read the license Specify Stations Assign License to Stations Check license consistency Distribute License to stations Creating New license Project Log on to the license management station PC as a user with maintenance privileges Start - select [All Programs] > [YOKOGAWA License], and right-click [License Manager] Select [Run as administrator] > License Manager starts From the menu bar, select [File] > [New] > [Project] The Create new license project dialog box appears Specify the following information: Project name: type a name for the System type: drop-down list, select a system product name [CENTUM VP] Click [OK] YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT license project (1 and characters) Creating license Project Specify the Station type Specify the Station Address YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Creating license Project Read the license Read the license key file from the license media and register the available licenses At this point you need to enter the Project ID number YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Creating license Project Assign available licenses to the each station YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Check license Consistency Check that the basic software and option software have been combined correctly and that the licenses have been properly assigned YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Distribute Licenses Distribute licenses to the license-assigned stations through the network or by using external medial Choose [Select All] – then [OK] YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Accept License After CENTUM VP or ProSafe-RS software package is installed, the licenses initially distributed through the network are accepted automatically After the licenses have been accepted, the status of the license-assigned station changes to OK YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT HIS Utility YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT HIS Utility Log on as CTM_MAINTENANCE group Start – [All programs] – [YOKOGAWA CENTUM] – [HIS Utility] [User] – [Add] – display [Add user] dialog box YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT HIS Utility On the dropdown list of [Domain or Computer Name], choose a Windows domain name or a local computer name Enter the user name and password for automatically start HIS functions after logging on Check [Enable Automatic Logon], [ Enable Centum Desktop] and [Enable HIS Automatic Start If automatic start of HIS functions is needed by more users after logging on, repeat the above procedure step to step to add the users Finish HIS Utility with [OK] button YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT End of the presentation THANH YOU FOR YOUR ATTENTION YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Page.99 ... pm Agenda CENTUM VP Maintenance Course Day Software compatibility Hardware setup prior to installation Software Environment Window set-up prior to installation (Vista/W7/Server) Centum VP installation.. .Maintenance Course Yokogawa Vietnam Co Ltd Service Department YOKOGAWA VIETNAM CO.LTD Copyright © Yokogawa Electric Corporation SERVICE DEPARTMENT Maintenance Course... Installation of Windows Settings of Network Installation of Windows Service Pack Installation of Centum VP Software Installation of Windows Security patch Setting of IT Security Settings of Windows