Tài liệu hướng dẫn cách tháo lắp các tấm ốp trên xe Toyota camry hybrid xv50 2012 2017 instrument panel các tấm ốp. Cung cấp các thông tin cho Kỹ thuật viên tiến hành sửa chữa nhanh chóng, chính xác, hiệu quả
INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD IP–1 INSTRUMENT PANEL SAFETY PAD PRECAUTION Code Shape PRECAUTION FOR VEHICLE WITH SRS AIRBAG AND SEAT BELT PRETENSIONER (a) Some operations in this section may affect the SRS airbags Prior to performing the corresponding operations, read the SRS airbag NOTICE TABLE OF BOLT, SCREW AND NUT Size Parts No φ=6 mm (0.24 in.) Length=20 mm (0.79 in.) 90119-06166 φ=5 mm (0.20 in.) Length=16 mm (0.63 in.) 93567-55016 φ=6 mm (0.24 in.) 90179-06115 φ=5 mm (0.20 in.) Length=15 mm (0.59 in.) 90164-50034 φ=5 mm (0.20 in.) Length=20 mm (0.79 in.) 93567-15020 φ=5 mm (0.20 in.) Length=16 mm (0.63 in.) 93567-15016 φ=6 mm (0.24 in.) Length=16 mm (0.63 in.) 90119-06480 IP IP–2 Code IP INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD Shape Size Parts No φ=6 mm (0.24 in.) Length=18 mm (0.71 in.) 90119-06428 φ=6 mm (0.24 in.) 90179-06206 φ=6 mm (0.24 in.) Length=15 mm (0.59 in.) 90119-06915 φ=8 mm (0.31 in.) Length=20 mm (0.79 in.) 91633-60820 φ=5 mm (0.20 in.) Length=16 mm (0.63 in.) 90159-50305 φ=5 mm (0.20 in.) Length=16 mm (0.63 in.) 93565-15016 φ=6 mm (0.24 in.) Length=20 mm (0.79 in.) 90159-60610 IP–3 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD COMPONENTS TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY 2.0 (20, 18 in.*lbf) STEERING COLUMN COVER 50 (510, 37) IP STEERING WHEEL ASSEMBLY LOWER NO STEERING WHEEL COVER LOWER NO STEERING WHEEL COVER 8.8 (90, 78 in.*lbf) STEERING PAD N*m (kgf*cm, ft.*lbf) : Specified torque B137279E04 IP–4 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD COMBINATION METER ASSEMBLY INSTRUMENT CLUSTER FINISH PANEL LOWER INSTRUMENT PANEL FINISH PANEL IP NO INSTRUMENT PANEL SUB-ASSEMBLY COWL SIDE TRIM SUB-ASSEMBLY LH COWL SIDE TRIM CLIP LOWER INSTRUMENT PANEL FINISH PANEL LH FRONT DOOR SCUFF PLATE LH B145864E01 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD IP–5 LOWER INSTRUMENT PANEL SUB-ASSEMBLY COWL SIDE TRIM SUB-ASSEMBLY RH COWL SIDE TRIM CLIP IP FRONT DOOR SCUFF PLATE RH INSTRUMENT PANEL NO UNDER COVER SUB-ASSEMBLY B137282E05 IP–6 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD NO INSTRUMENT CLUSTER FINISH PANEL GARNISH NO INSTRUMENT CLUSTER FINISH PANEL GARNISH SHIFT LEVER KNOB SUB-ASSEMBLY IP FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY UPPER CONSOLE REAR PANEL SUBASSEMBLY B145865E01 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD IP–7 INSTRUMENT PANEL NO REGISTER ASSEMBLY without Navigation System: with Navigation System: IP RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY UPPER CONSOLE PANEL SUB-ASSEMBLY B145866E02 IP–8 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD FRONT PILLAR GARNISH CLIP FRONT PILLAR GARNISH RH FRONT PILLAR GARNISH CLIP FRONT PILLAR GARNISH LH INSTRUMENT PANEL NO REGISTER ASSEMBLY INSTRUMENT PANEL NO REGISTER ASSEMBLY NO CONSOLE BOX INSERT FRONT IP NO CONSOLE BOX INSERT FRONT CONSOLE BOX CARPET CONSOLE BOX ASSEMBLY CONSOLE BOX POCKET Non-reusable part B145867E01 IP–9 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD INSTRUMENT PANEL NO SPEAKER PANEL SUB-ASSEMBLY INSTRUMENT PANEL NO SPEAKER PANEL SUB-ASSEMBLY NO DEFROSTER NOZZLE GARNISH for RH Side: for LH Side: FRONT NO SPEAKER ASSEMBLY FRONT NO SPEAKER ASSEMBLY IP or or or 20 (204, 15) or INSTRUMENT PANEL SAFETY PAD ASSEMBLY N*m (kgf*cm, ft.*lbf) : Specified torque B145868E02 IP–10 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD NO INSTRUMENT PANEL STAY GLOVE BOX LIGHT ASSEMBLY DEFROSTER NOZZLE ASSEMBLY NO HEATER TO REGISTER DUCT PLASMACLUSTER SIDE NO DEFROSTER NOZZLE DUCT SIDE NO DEFROSTER NOZZLE DUCT NO HEATER TO REGISTER DUCT IP NO HEATER TO REGISTER DUCT with Navigation System: FRONT PASSENGER AIRBAG ASSEMBLY NO ANTENNA CORD SUB-ASSEMBLY NAVIGATION ANTENNA ASSEMBLY N*m (kgf*cm, ft.*lbf) : Specified torque 7.0 (71, 62 in.*lbf) B137288E03 IP–27 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD (b) Install the bolts or and nuts or or or or IP or B134014E05 (c) Engage each clamp (d) Install the bolt Torque: 7.0 N*m (71 kgf*cm, 62 in.*lbf) (e) Install the passenger airbag bolts Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) IP–28 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD (f) Connect each connector and install the instrument panel safety pad assembly IP Clamp B134012E03 CONNECT INSTRUMENT PANEL WIRE ASSEMBLY (See page RS-383) INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD Guide Guide IP–29 INSTALL NO DEFROSTER NOZZLE GARNISH (a) Connect each connector (b) Engage the guides (c) Engage the clips and install the No defroster nozzle garnish INSTALL FRONT NO SPEAKER ASSEMBLY (for LH Side) (See page AV-146) INSTALL INSTRUMENT PANEL NO SPEAKER PANEL SUB-ASSEMBLY (a) Engage the guides (b) Engage the claws and the clips to install the instrument panel No speaker panel subassembly B134011E01 IP B134009E01 B134007 INSTALL INSTRUMENT PANEL NO REGISTER ASSEMBLY (a) Engage the clips and install the instrument panel No register assembly INSTALL FRONT PILLAR GARNISH LH (See page IR38) INSTALL FRONT NO SPEAKER ASSEMBLY (for RH Side) HINT: Use the same procedures described for the LH side (See page AV-146) IP–30 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD 10 INSTALL INSTRUMENT PANEL NO SPEAKER PANEL SUB-ASSEMBLY (a) Engage the guides (b) Engage the claws and the clips to install the instrument panel No speaker panel subassembly Guide B134010E01 11 INSTALL INSTRUMENT PANEL NO REGISTER ASSEMBLY (a) Engage the clips and install the instrument panel No register assembly 12 INSTALL FRONT PILLAR GARNISH RH (See page IR39) IP B134008 13 INSTALL NO CONSOLE BOX INSERT FRONT (a) Engage the clip (b) Install the No console box insert front with the screws B134006E01 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD IP–31 14 INSTALL NO CONSOLE BOX INSERT FRONT (a) Engage the clip (b) Install the No console box insert front with the screws B134005E01 15 INSTALL CONSOLE BOX ASSEMBLY (a) Install the screws B134002E01 (b) Install the console box assembly with the bolts (c) Engage the clamp Clamp B149935E01 16 INSTALL CONSOLE BOX CARPET (a) Install the console box carpet 17 INSTALL CONSOLE BOX POCKET (a) Install the console box pocket 18 INSTALL RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/o Navigation System) (See page AV-137) B134004 19 INSTALL NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System) (See page NS-194) IP IP–32 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD 20 INSTALL INSTRUMENT PANEL NO REGISTER ASSEMBLY (a) Engage the clips and install the instrument panel No register assembly 21 INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (a) Connect each connector B134001 (b) Engage the claws (c) Install the upper console panel sub-assembly with the screws B133997E01 22 INSTALL UPPER CONSOLE REAR PANEL SUBASSEMBLY (a) Connect the connector (b) Engage the claws and clips to install the upper console rear panel sub-assembly IP 23 INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (a) with Seat Heater System: (1) Connect each connector B149933 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD IP–33 (b) Engage the claws and the clips to install the floor shift position indicator housing sub-assembly B149956 24 INSTALL NO INSTRUMENT CLUSTER FINISH PANEL GARNISH (a) Engage the clips and install the No instrument cluster finish panel garnish IP B145876 25 INSTALL NO INSTRUMENT CLUSTER FINISH PANEL GARNISH (a) Engage the clips and install the No instrument cluster finish panel garnish B145875 26 INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (a) Install the shift lever knob sub-assembly B145874 IP–34 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD 27 INSTALL LOWER INSTRUMENT PANEL SUBASSEMBLY (a) Engage the claws and clips (b) Install the screws (c) Install the lower instrument panel sub-assembly with the bolt B133992E01 28 INSTALL INSTRUMENT PANEL NO UNDER COVER SUB-ASSEMBLY (a) Engage the claws and guides and install the instrument panel No under cover 29 INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH (See page IR-42) 30 INSTALL FRONT DOOR SCUFF PLATE RH (See page IR-42) IP Guide B133989E01 31 INSTALL COMBINATION METER ASSEMBLY (a) Connect each connector (b) Install the combination meter assembly with the screws B133987E01 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD IP–35 32 INSTALL INSTRUMENT CLUSTER FINISH PANEL (a) Engage the guide and the claws (b) Install the instrument cluster finish panel with the clips 33 INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (a) Connect the connector Guide B133985E01 (b) Engage the claws and clips to install the lower instrument panel finish panel 34 INSTALL NO INSTRUMENT PANEL SUBASSEMBLY (a) Connect the connector B145872 (b) Engage the claws and clips to install the No instrument panel sub-assembly 35 INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY (See page SR-41) 36 ADJUST SPIRAL CABLE SUB-ASSEMBLY (See page RS-360) B133982 IP IP–36 INSTRUMENT PANEL – INSTRUMENT PANEL SAFETY PAD 37 INSTALL STEERING COLUMN COVER (a) Engage the claw and install the upper steering column cover (b) Engage the claws and install the lower steering column cover (c) Install the steering column cover with the screws B137294E03 38 INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH (a) Install the air hose and connect each connector (b) Engage the claw and the clips (c) Instal the instrument panel finish panel LH with the screw and bolt 39 INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (See page IR-41) 40 INSTALL FRONT DOOR SCUFF PLATE LH (See page IR-41) IP 41 INSTALL STEERING WHEEL ASSEMBLY (See page SR-42) 42 INSTALL STEERING PAD (See page RS-346) 43 INSTALL LOWER NO STEERING WHEEL COVER (See page RS-347) 44 INSTALL LOWER NO STEERING WHEEL COVER (See page RS-347) B145878E01 45 CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 46 INSPECT STEERING PAD (See page RS-347) 47 INSPECT SRS WARNING LIGHT (RS-1) 48 PERFORM INITIALIZATION NOTICE: Some systems need initialization after reconnecting the cable to the negative battery terminal (See page IN-43) IP–36 INSTRUMENT PANEL – REAR CONSOLE BOX REAR CONSOLE BOX INSTRUMENT PANEL BODY COMPONENTS NO INSTRUMENT CLUSTER FINISH PANEL GARNISH NO INSTRUMENT CLUSTER FINISH PANEL GARNISH SHIFT LEVER KNOB SUB-ASSEMBLY IP FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY UPPER CONSOLE REAR PANEL SUB-ASSEMBLY CONSOLE BOX CARPET CONSOLE BOX POCKET CONSOLE BOX ASSEMBLY B145869E01 INSTRUMENT PANEL – REAR CONSOLE BOX IP–37 CONSOLE COMPARTMENT DOOR SUB-ASSEMBLY IP REAR CONSOLE END PANEL SUB-ASSEMBLY B145870E01 IP–38 INSTRUMENT PANEL – REAR CONSOLE BOX REMOVAL REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (See page IP-14) REMOVE NO INSTRUMENT CLUSTER FINISH PANEL GARNISH (See page IP-14) REMOVE NO INSTRUMENT CLUSTER FINISH PANEL GARNISH (See page IP-14) REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (See page IP-15) REMOVE UPPER CONSOLE REAR PANEL SUBASSEMBLY (See page IP-15) REMOVE CONSOLE BOX POCKET (See page IP-17) REMOVE CONSOLE BOX CARPET (See page IP-17) REMOVE CONSOLE BOX ASSEMBLY (a) Remove the screws B134002 (b) Disengage the clamp (c) Remove the bolts and the console box assembly IP Clamp B149935E02 DISASSEMBLY B137269 REMOVE REAR CONSOLE END PANEL SUBASSEMBLY (a) Disengage the clips and remove the rear console end panel sub-assembly INSTRUMENT PANEL – REAR CONSOLE BOX IP–39 REMOVE CONSOLE COMPARTMENT DOOR SUBASSEMBLY (a) Remove the screws and the console compartment door sub-assembly B137270 REASSEMBLY INSTALL CONSOLE COMPARTMENT DOOR SUBASSEMBLY (a) Install the console compartment door sub-assembly with the screws INSTALL REAR CONSOLE END PANEL SUBASSEMBLY (a) Engage the clips and install the rear console end panel sub-assembly B137270 IP B137269 INSTALLATION B134002 INSTALL CONSOLE BOX ASSEMBLY (a) Install the screws IP–40 INSTRUMENT PANEL – REAR CONSOLE BOX (b) Install the console box assembly with the bolts (c) Engage the clamp Clamp INSTALL CONSOLE BOX CARPET (See page IP-30) INSTALL CONSOLE BOX POCKET (See page IP-30) INSTALL UPPER CONSOLE REAR PANEL SUBASSEMBLY (See page IP-31) INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (See page IP-31) INSTALL NO INSTRUMENT CLUSTER FINISH PANEL GARNISH (See page IP-32) INSTALL NO INSTRUMENT CLUSTER FINISH PANEL GARNISH (See page IP-32) INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (See page IP-32) B149935E02 IP