tai lieu sua xe may honda

Ngày tải lên: 20/12/2013, 22:15

... động chạy trong Scheduled Tasks. Chọn Start.Programs.Accessories.System Tools.Scheduled Task để xem những chương trình nào đang sử dụng tính năng này. Xóa tất cả những thứ liên quan đến Chkdsk ... trình kiểm tra (treo máy) hoặc không khắc phục được lỗi, hãy sử dụng tiện ích checkdisk (chkdsk.exe), fixmbr và fixboot của Recovery Console (bộ tiện ích có trong đĩa cài đặt Windows) để kiểm ... 2000/XP, đăng nhập với quyền Administrator, vào Control Pannel\Administrative Tools\Event Viewew để xem thông báo lỗi. Đây là một trong những nơi cần tham khảo, tìm hiểu nguyên nhân để biết cách...

Ngày tải lên: 20/12/2013, 22:15

Ngày tải lên: 20/12/2013, 22:15

Ngày tải lên: 22/12/2013, 14:15

Ngày tải lên: 08/01/2014, 22:07

Ngày tải lên: 09/04/2014, 15:44

Ngày tải lên: 09/04/2014, 17:26

Ngày tải lên: 26/01/2014, 14:20

Ngày tải lên: 27/05/2014, 11:51

... a value X between values (A and B) (A ≤ X ≤ B). COMMENT: It may be necessary to carry out a few preliminary test in order to obtain the correct value. If the values are incorrect after several ... the trim identification code. NOTE: some of these items of information are not required for certain export markets. The plates described above are shown in their most complete form. ALLOCATION ... SPECIFICATIONS Vehicle identification 01 LOCATION OF THE VEHICLE IDENTIFICATION PLATE Plates (A) and (B) may be separate or on a single plate (according to specification). Position n° 2 Position n° 1 Position...

Ngày tải lên: 22/10/2012, 15:42

... of two bolts around the gearbox. 92903S C engines 21-13 MANUAL GEARBOXES Special features GEAR CHANGE PATTERN The gearboxes of the following types: JB0 JB4 JB2 JB1 JB3 5 forward gears JB5 1 ... the gearbox with oil. 21-28 MANUAL GEARBOXES 5th speed linkage in situ 21 On the secondary shaft: Remove shouldered washer (64). PRG21.1 Remove the fixed gear using tool B.Vi. 28-01-02- 03 fitted ... 1007. 88575R REFITTING On the secondary shaft: Put three drops of Loctite FRENBLOC on the fixed gear splines. Fit the fixed gear using tool B. Vi. 1175 and shoul- dered washer (64). 93462R Remove tool B....

Ngày tải lên: 22/10/2012, 15:42

... this document are based on the technical specifications current when it was prepared. The methods may be modified as a result of changes introduced by the manufacturer in the production of the various ... GENERAL Checking and adjusting the front axle geometry ADJUSTING PARALLELISM One of several cases may arise : Parallelism incorrect by more than 6 mm. Parallelism Distribution Correction to be carried ... by the same number of turns in opposite directions on the left hand and right hand sides, to obtain the same reading for dimension A on both sides. INCORRECTCORRECT Adjust the parallelism by...

Ngày tải lên: 22/10/2012, 15:42

... level in the circuit. There may have been too much refrigerant. The humidity in the circuit may have formed a plug of ice in the pressure relief valve or the valve may be faulty (slight lack of ... ventilators (a) and (c) may be closed. POSITION The air flow is distributed between all the ventilators (a), (b), (c), (d), (e), (f). The dashboard ventilators (a) and (c) may be closed. FAN CONTROL ... refrigerant and vice versa. MAINTENANCE When a vehicle is fitted with air conditioning, the engine may heat up more than on other vehicles. It is recommended that the level of coolant is checked...

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

... NAUDER* and stainless steel clips 2 - Rivets Part number : 77 03 072 280 3 - Neoprene adhesive 4 - Brush 5 - Seal Part number: * NAUDER : Please contact your local After Sales Head Office for details. 94791S GENERAL Tooling ... 53 CABRIOLET After removing the external trim, remove the ri- vets from the rear section and the stainless steel clips. Remove the adhesive tape from the front section. Unstick the front section. 73-7 ... hooks (2). Unclip the trim. TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE) Bonnet trim 73 A PRF7301 Tailgate trim 73 B 73-1 REMOVAL Insert a flat screwdriver in hole (2) in the upper section, so...

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

... this document are based on the technical specifications current when it was prepared. The methods may be modified as a result of changes by the manufacturer in the production of the various component ... SIDE STRUCTURE UPPER REAR STRUCTURE UPPER BODY SECTION BODY PROTECTION SIDE OPENINGS BONNET AND TAILGATE Contents GENERAL Engine - Clutch - Gearbox Vehicle dimensions Lifting Description of parts...

Ngày tải lên: 22/10/2012, 15:42