net oda disbursements to africa 2000 09 billion usd current

... Always torque brake lines when installing Preparation SPECIAL SERVICE TOOLS NGAX0002 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here Tool number ... the noise will stop occur in the hubs AX-10 Stop the vehicle or decrease speed to less than 40 km/h (25 mph) Return the transfer case lever to the 2H position once, then re-shift to the 4H position ... Remove free-running hub assembly (4WD models) Refer to “Auto-lock Free-running Hub”, AX-9 Remove wheel hub and rotor disc Refer to “Wheel Hub and Rotor Disc”, AX-11 TF PD SFA828B Separate drive shaft...

Ngày tải lên: 22/10/2012, 11:50

... terminal ¼ to headlamp RH terminal M and ¼ from lighting switch terminal ¼ to headlamp LH terminal M and ¼ to combination meter terminal 26 for the high beam indicator Ground is supplied to terminal ... tab-locking type connectors are disconnected by pushing or lifting the locking tab(s) Refer to the illustration below Refer to EL-6 for description of the slide-locking type connector CAUTION: Do not ... type connectors are disconnected by pushing or pulling the slider Refer to the illustration below CAUTION: Do not pull the harness or wires when disconnecting the connector Be careful not to damage...

Ngày tải lên: 22/10/2012, 11:51

... MAKE THIS SERVICE MANUAL BETTER! Your comments are important to NISSAN and will help us to improve our Service Manuals Use this form to report any issues or comments you may have regarding our ... clear and easy to follow? (circle your answer) YES NO Please comment: What information should be included in NISSAN Service Manuals to better support you in servicing or repairing customer vehicles? ... engine, WD22 KA24DE engine 2000MY ★ 2：Except models L30 KA24DE engine 2000MY CATALYST Three way catalyst function Test value (GST display) TID CID 01H 02H 05H 05H 06H 07H 09H 0AH 0BH 0CH 0DH 19H...

Ngày tải lên: 22/10/2012, 11:51

... the MIL to light up ¼ Be sure to connect and lock the connectors securely after work A loose (unlocked) connector will cause the MIL to light up due to an open circuit (Be sure the connector is ... Reverse clutch R/C To transmit input power to front sun gear High clutch H/C To transmit input power to front planetary carrier 11 Forward clutch 16 F/C To connect front planetary carrier 11 with ... Accumulator control valve Accumulator control sleeve Regulate accumulator backpressure to pressure suited to driving conditions Manual valve Directs line pressure to oil circuits corresponding to...

Ngày tải lên: 22/10/2012, 11:51

... pedal/foot effort to bring the vehicle to a pressure such that vehicle stopping time equals to to seconds To cool the brake system, drive the vehicle at 50 km/h (31 MPH) for minute without stopping Repeat ... of stopper cap outward HA SC EL SBR938A BR-13 IDX MASTER CYLINDER Disassembly (Cont’d) Remove piston stopper while piston is pushed into cylinder Remove piston assemblies If it is difficult to ... seal into groove on cylinder body With piston boot fitted to piston, insert piston boot into groove on cylinder body and install piston Properly secure piston boot CAUTION: ¼ Secure dust seal property...

Ngày tải lên: 22/10/2012, 11:51

... verifying the customer concern or symptom, check ASSIST for Technical Service Bulletins (TSB’s) related to that concern or symptom If a TSB relates to the symptom, follow the procedure to repair the ... related to the SRS BT-2 PREPARATION Special Service Tools Special Service Tools NGBT0027 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here Tool ... noise occurs and any customers comments; refer to BT-8 This information is necessary to duplicate the conditions that exist when the noise occurs ¼ The customer may not be able to provide a detail...

Ngày tải lên: 22/10/2012, 11:51

... FUSE AND FUSIBLE LINK BOX Terminal Arrangement Terminal Arrangement NGEL0149 AEL521C JOINT CONNECTOR Terminal Arrangement Terminal Arrangement NGEL0198 AEL523C ELECTRICAL UNITS Terminal Arrangement...

Ngày tải lên: 22/10/2012, 11:51

... prevent damage to the transmission GI-46 LIFTING POINTS AND TOW TRUCK TOWING Tow Truck Towing (Cont’d) TOWING POINT NGGI0008S0 409 Never tow the vehicle using only the towing points To avoid damaging ... terminal into female terminal SEL265V GI-20 HOW TO CHECK TERMINAL How to Probe Connectors (Cont’d) ¼ Some connectors not have a notch above each terminal To probe each terminal, remove the connector ... connector to be measured Procedure with Generic Scan Tool (GST, OBD-II scan tool) MA Check after connecting the connector to be measured Procedure without CONSULT or GST EM Insert key into ignition...

Ngày tải lên: 22/10/2012, 11:51

... radiator shroud and horns ¼ Tape the harness connectors to prevent water from entering Apply water by hose to the back side of the radiator core vertically downward Apply water again to all radiator ... KA24DE System Check (Cont’d) CHECKING RADIATOR CAP NGLC0112S04 To check radiator cap, apply pressure to radiator cap with a radiator cap tester Radiator cap relief pressure: Standard 78 - 98 kPa ... CHECKING RADIATOR GI EC FE NGLC0112S02 Check radiator for mud or clogging If necessary, clean radiator as follows ¼ Be careful not to bend or damage the radiator fins ¼ When radiator is cleaned...

Ngày tải lên: 22/10/2012, 11:51

... bolt C to the torque of 68 to 87 N·m (6.9 to 8.9 kg-m, 50 to 64 ft-lb) Tighten bolt D to the torque of 68 to 87 N·m(6.9 to 8.9 kg-m, 50 to 64 ft-lb) Tighten bolt A to the torque of 68 to 87 N·m ... N·m (6.9 to 8.9 kg-m, 50 to 64 ft-lb) Tighten bolt B to the torque of 68 to 87 N·m (6.9 to 8.9 kg-m, 50 to 64 ft-lb) Tighten bolt E to the torque of 68 to 87 N·m (6.9 to 8.9 kg-m, 50 to 64 ft-lb) ... following inspection ¼ Total preload a) Turn drive pinion in both directions several times to set bearing rollers b) Check total preload with Tool Tool number: ST3127S000 (J25765-A) Total preload: 1.4...

Ngày tải lên: 22/10/2012, 11:51

... terminal ¼ to starter motor windings terminal + The starter motor plunger closes and provides a closed circuit between the battery and the starter motor The starter motor is grounded to the cylinder ... terminal ¼ to starter motor windings terminal + The starter motor plunger closes and provides a closed circuit between the battery and the starter motor The starter motor is grounded to the cylinder ... terminal ¼ to starter motor windings terminal + The starter motor plunger closes and provides a closed circuit between the battery and the starter motor The starter motor is grounded to the cylinder...

Ngày tải lên: 22/10/2012, 11:51

... collector Do not use compressed air CL-2 PREPARATION Special Service Tools Special Service Tools NGCL0002 The actual shapes of Kent-Moore tools may differ from those of special service tools ... ¼ ¼ NGCL0007 Use a screwdriver to remove stopper ring while pushing push rod into cylinder When installing stopper ring, tap in lightly while pushing push rod into cylinder Inspection NGCL0008 ... PRESSURE PLATE (Distortion) FLYWHEEL (Distortion) 2 ENGINE MOUNTING (Loose) CLUTCH DISC (Lining broken) CL-9 OPERATING CYLINDER PISTON CUP (Damaged) CL-12 CL-8 MASTER CYLINDER PISTON CUP (Damaged)...

Ngày tải lên: 22/10/2012, 11:51

... PD AX SST735C ¼ Install sector shaft into sector shaft cover Set adjusting screw to its outermost position Before installing sector shaft, apply multi-purpose grease to adjusting screw and adjusting ... piston rack at straight-ahead position Turn piston rack about 10° to 15° toward yourself with your finger This enables smooth insertion of sector gear ST696 SST328C 11 Gradually insert sector ... sector shaft into gear housing 12 Tighten sector shaft cover bolts 13 Set worm gear turning torque by turning sector shaft adjusting screw and locking with lock nut Refer to “TURNING TORQUE MEASUREMENT”,...

Ngày tải lên: 22/10/2012, 11:51

... Block 120 (Cont’d) Piston, Piston Ring and Piston Pin 122 AVAILABLE PISTON 122 PISTON RING .122 AVAILABLE PISTON 123 PISTON RING .123 PISTON PIN 124 Connecting ... NGEM0060S09 To remove valve guide, heat cylinder head to 120 to 140°C (248 to 284°F) by soaking in heated oil Drive out valve guide with a press [under a 20 kN (2 ton, 2.2 US ton, 2.0 Imp ton) pressure] ... piston oversize according to amount of cylinder wear Oversize pistons are available for service Refer to SDS, EM-62 Cylinder bore size is determined by adding piston -to- bore clearance to piston...

Ngày tải lên: 22/10/2012, 11:51

... Special Service Tool Special Service Tool NGFE0001 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here Tool number (Kent-Moore No.) Tool name Description ... connecting accelerator wire, be careful not to twist or scratch its inner wire ¼ Refer to EL-170 (“AUTOMATIC SPEED CONTROL DEVICE”) for ASCD wire adjustment GI MA EM LC EC CL MT AT AFE090 TF PD AX ... electrical connectors Remove filler protector 1) 2) Remove the quick connectors as follows Put mating marks on the connectors for correct installation Hold the sides of the connector, push in tabs,...

Ngày tải lên: 22/10/2012, 11:51

... blower motor and fuse block (J/B) ¼ Harness connectors M27 and M62 CL MT CHECK BLOWER MOTOR AT Disconnect blower motor harness connector Apply 12 volts to blower motor terminal and ground to blower ... refer to “POWER SUPPLY ROUTING”, EL-9 Are fuses OK? OK ᮣ GO TO NG ᮣ GO TO CHECK BLOWER MOTOR POWER SUPPLY CIRCUIT Disconnect blower motor harness connector Check voltage between blower motor harness ... blower motor terminal TF PD AX AHA455A Does blower motor rotate? Yes ᮣ Reconnect blower motor connector and go to Trouble Diagnosis Procedure for Blower Motor, HA-29 No ᮣ SU Replace blower motor BR...

Ngày tải lên: 22/10/2012, 11:51

... Generator SC-19 EC Generator - See Alternator SC-19 Generic scan tool (GST) EC-89, 663 FE Glass BT-18 Grease MA-14 CL H MT Harness connector EL-5 Harness connector ... diff .PD-52, 78 Torque converter installation .AT-263 Torque converter clutch solenoid valve .AT-151, 159 Torsion bar spring .SU-14 Tow truck towing GI-45 Towing point ... Pinion gear height diff .PD-25, 48, 75 Piston assembly EM-52, 111 Piston pin inspection EM-45, 104 Piston ring inspection .EM-46, 104 Piston to bore clearance EM-47, 106 PNP/SW - Wiring...

Ngày tải lên: 22/10/2012, 11:51

... filler neck slowly to allow air in system to escape MT SMA182B SMA412B Fill radiator and reservoir tank to specified level Warm up engine to normal operating temperature without radiator cap installed ... gauge so as not to overheat the engine Stop engine and cool it down ¼ Cool down using a fan to reduce the time ¼ If necessary, refill radiator up to filler neck Refill reservoir tank to MAX level ... as not to overheat the engine Stop engine and cool it down ¼ Cool down using a fan to reduce the time ¼ If necessary, refill radiator up to filler neck with coolant Refill reservoir tank to Max...

Ngày tải lên: 22/10/2012, 11:51

... chart shown at left to determine the proper reading torque (Length of torque wrench vs setting or reading torque) Reference: Formula to convert torque wrench indication to the true torque value: T ... Special Service Tools Special Service Tools NGMT0045 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here Tool number (KentMoore No.) Tool name Description ... Special Service Tools Special Service Tools NGMT0001 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here Tool number (Kent-Moore No.) Tool name GI...

Ngày tải lên: 22/10/2012, 11:51

... Connect CONSULT-II to data link connector Turn ignition switch ON ABR847 Touch “START” Touch “AIRBAG” Touch “SELF-DIAG [CURRENT] ” Self-diagnosis result is displayed on “SELF-DIAG [CURRENT] ” SRS695 ... KV991065S0 (J38381–30)] to attach passenger air bag module, or for pre-tensioner, use deployment tool adapter [SST: KV99 1090 00 (J44230)} to attach seat belt pre-tensioner, to deployment tool [SST: KV99106400 ... bag module connector to air bag harness connector Attach passenger air bag module connector clip to lid Close lid and glove box Connect both battery cables Conduct Self-diagnosis to ensure entire...

Ngày tải lên: 22/10/2012, 11:51