gia o to nissan sunny
Shop manual ô tô NISSAN 2000 Xterra - P1
... installing. Preparation SPECIAL SERVICE TOOLS NGAX0028 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore No.) Tool name Description KV40101000 (J25604-01) Axle ... Refer to “Auto-lock Free-running Hub”, AX-9. 2. Remove torsion bar spring. Refer to “Torsion Bar Spring”, SU-14. 3. Remove shock absorber lower fixing bolt. 4. Remove lower link, fixing bolts. Support ... Always torque brake lines when installing. Preparation SPECIAL SERVICE TOOLS NGAX0002 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore...
Ngày tải lên: 22/10/2012, 11:50
Shop manual ô tô NISSAN 2000 Xterra - P3
... to the illustra- tion below. CAUTION: Do not pull the harness or wires when disconnecting the connector. Be careful not to damage the connector support bracket when disconnecting the connector. AEL299C HARNESS ... to the following: ẳ GI-10, HOW TO READ WIRING DIAGRAMS ẳ EL-9, POWER SUPPLY ROUTING for power distribution circuit. When you perform trouble diagnosis, refer to the following: ẳ GI-34, HOW TO ... related to OBD> ẳ The slide-locking type connectors help prevent incomplete locking and accidental looseness or disconnec- tion. ẳ The slide-locking type connectors are disconnected by pushing or...
Ngày tải lên: 22/10/2012, 11:51
Shop manual ô tô NISSAN 2000 Xterra - P4
... to improve our Service Manuals. Use this form to report any issues or comments you may have regarding our Service Manuals. Please print this form and type or write your comments below. Mail or ... issue or problem in detail: Is the organization of the manual clear and easy to follow? (circle your answer) YES NO Please comment: What information should be included in NISSAN Service Manuals to ... reserved. No part of this Service Manual may be reproduced or stored in a retrieval system, or transmitted in any form, or by any means, electronic, mechanical, photo-copying, recording or otherwise, without...
Ngày tải lên: 22/10/2012, 11:51
Shop manual ô tô NISSAN 2000 Xterra - P5
... seconds. SAT967I 4. Turn ignition switch to ON position. (Do not start engine.) 5. Does O/ D OFF indicator lamp come on for about 2 seconds? AAT612A YesorNo Yes ᮣ GO TO 2. No ᮣ Go to “1. O/ D OFF ... circuit refer to EL-9 . When you perform trouble diagnosis, refer to the followings: ẳ HOW TO FOLLOW TEST GROUP IN TROUBLE DIAGNOSIS refer to GI-34 . ẳ HOW TO PERFORM EFFICIENT DIAGNOSIS FOR AN ELECTRICAL ... DESCRIPTION CONSULT-II (Cont’d) AT-46 Special Service Tools NGAT0006 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore No.) Tool...
Ngày tải lên: 22/10/2012, 11:51
Shop manual ô tô NISSAN 2000 Xterra - P6
... Insert piston seal into groove on cylinder body. 2. With piston boot fitted to piston, insert piston boot into groove on cylinder body and install piston. 3. Properly secure piston boot CAUTION: ẳ ... circuit Control unit or control unit connector Solenoid valve relay stuck Power supply for solenoid valve relay coil BR-66 ★1: If one or more wheels spin on a rough or slippery road for 40 seconds or ... trouble diagnosis, refer to the followings: ẳ HOW TO FOLLOW TEST GROUP IN TROUBLE DIAGNOSIS refer to GI-34 . ẳ HOW TO PERFORM EFFICIENT DIAGNOSIS FOR AN ELECTRICAL INCIDENT” refer to GI-23 . GI MA EM LC EC FE CL MT AT TF PD AX SU ST RS BT HA SC EL IDX PRECAUTIONS Supplemental...
Ngày tải lên: 22/10/2012, 11:51
Shop manual ô tô NISSAN 2000 Xterra - P7
... customer concern or symptom, check ASSIST for Technical Service Bulletins (TSB’s) related to that concern or symptom. If a TSB relates to the symptom, follow the procedure to repair the noise. LOCATE ... sure to keep oil away from it. ẳ Hood adjustment: Adjust at hinge portion. ẳ Hood lock adjustment: After adjusting, check hood lock control operation. Apply a coat of grease to hood locks engaging ... necessary to duplicate the conditions that exist when the noise occurs ẳ The customer may not be able to provide a detail description or location of the noise. Attempt to obtain all the facts and conditions...
Ngày tải lên: 22/10/2012, 11:51
Shop manual ô tô NISSAN 2000 Xterra - P9
... that these connectors belong to the same com- ponent. 30 Connector color ẳ This shows a code for the color of the connector. For code meaning, refer to wire color codes, Number 14 of this chart. 31 Fusible ... indicate a loose or poor elec- trical connection. Hint Connectors can be exposed to moisture. It is possible to get a thin film of corrosion on the connector terminals. A visual inspection may not reveal ... facilities. It is illegal to pour used oil onto the ground, down sewers or drains, or into water courses. The regulations concerning the pollution vary from country to country. PRECAUTIONS FOR FUEL NGGI0001S06 Use...
Ngày tải lên: 22/10/2012, 11:51
Shop manual ô tô NISSAN 2000 Xterra - P10
... SERVICE TOOLS =NGLC0068 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore No.) Tool name Description (J34301-C) Oil pressure ... Remove lower radiator shroud. 6. Remove radiator shroud. 7. Remove A/T oil cooler hoses (A/T models only). 8. Disconnect coolant reservoir hose. 9. Remove radiator. 10. After replacing radiator, ... resistance to fan rota- tion Damaged fan blades Damaged radiator shroud ——— Improper coolant mixture ratio ——— Poor coolant quality ——— Insufficient coolant Coolant leaks Cooling hose Loose clamp Cracked...
Ngày tải lên: 22/10/2012, 11:51
Shop manual ô tô NISSAN 2000 Xterra - P11
... Tighten bolt A to the torque of 68 to 87 N·m (6.9 to 8.9 kg-m, 50 to 64 ft-lb). f) Tighten bolt B to the torque of 68 to 87 N·m (6.9 to 8.9 kg-m, 50 to 64 ft-lb). g) Tighten bolt E to the torque of ... A. b) Temporarily tighten nut B. c) Tighten bolt C to the torque of 68 to 87 N·m (6.9 to 8.9 kg-m, 50 to 64 ft-lb). d) Tighten bolt D to the torque of 68 to 87 N·m(6.9 to 8.9 kg-m, 50 to 64 ft-lb). e) ... (Cont’d) PD-33 Preparation SPECIAL SERVICE TOOLS NGPD0052 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore No.) Tool...
Ngày tải lên: 22/10/2012, 11:51
Shop manual ô tô NISSAN 2000 Xterra - P12
... refer to the following: ẳ HOW TO READ WIRING DIAGRAMS, GI-10 ẳ POWER SUPPLY ROUTING for power distribution circuit, EL-11 When you perform trouble diagnosis, refer to the following: ẳ HOW TO FOLLOW ... terminal 3 ẳ to starter motor windings terminal +. The starter motor plunger closes and provides a closed circuit between the battery and the starter motor. The starter motor is grounded to the cylinder ... interlock relay terminal 3 ẳ to starter motor windings terminal +. The starter motor plunger closes and provides a closed circuit between the battery and the starter motor. The starter motor is grounded...
Ngày tải lên: 22/10/2012, 11:51
Shop manual ô tô NISSAN 2000 Xterra - P14
... SPECIFICATIONS (SDS) Clutch Control System CL-14 Special Service Tools NGCL0002 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore ... air. PRECAUTIONS Precautions CL-2 CLUTCH SECTION CL CONTENTS PRECAUTIONS 2 Precautions 2 PREPARATION 3 Special Service Tools 3 Commercial Service Tools 3 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING ... cup, for wear or damage ẳ Return spring, for wear or damage ẳ Dust cover, for cracks, deformation, or damage ẳ Reservoir, for deformation or damage CLUTCH MASTER CYLINDER Components CL-8 Components NGCL0004 ACL106 1....
Ngày tải lên: 22/10/2012, 11:51
Shop manual ô tô NISSAN 2000 Xterra - P13
... connector. 5. Remove knee protector. 6. Disconnect ignition switch and shift lock solenoid connectors. 7. Disconnect shift cable. 8. Remove bolt from lower joint. 9. Remove two steering column bolts ... shape of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore No.) Tool name Description ST27180001 (J25726-A) Steering wheel puller NT544 Removing ... force Drive belt looseness Improper steering wheel Improper installation or looseness of tilt lock lever Steering column deformation or damage Improper installation or looseness of steering column Steering...
Ngày tải lên: 22/10/2012, 11:51
