Tài liệu Digital Signal Cross-Connect Solutions pptx

www.adc.com • +1-952-938-8080 • 1-800-366-3891 307 Digital Signal Cross-Connect Solutions DS1 Signal Rate MiniDSX-1 Front and Rear Cross-Connect 308 DSXi ™ 84-Termination Cross-Connect Panels 311 DSX-1 Accessories 315 DS3 Signal Rate DSX-3 Minimum Point of Presence Panels 320 RZX-3 Panels 323 Multifunction Panel 327 DSX-3 Accessories 330 Extend TM Optical/Electrical Line Extender 333 DSX Relay Racks and Accessories 335 308 6/04 • 1247379 MSO Market Solutions www.adc.com • +1-952-938-8080 • 1-800-366-3891 308 Digital Signal Cross-Connect - DS1 MiniDSX-1 The eight-termination MiniDSX-1 is especially designed for small central or remote offices and customer premises demarcation points. These panels can be used for monitoring, terminating, accessing, and reconfiguring DS1 (1.544 Mbps) and DS1C (3.152 Mbps) circuits. The front cross-connect panel provides jack access and cross-connections on the front and IN/OUT equipment terminations on the rear of the panel. The rear cross-connect panel has jacks on the front with the cross-connect and IN/OUT equipment terminations on the back of the panel. Chassis include one preinstalled eight-termination module (blanks occupy unused positions). Additional modules are ordered as needed. Cross- Connect Jumper OUT IN MiniDSX-1 Permanent Equipment Cable Network Element A Tx OUT OUT OUT IN IN Rx IN X-OUT X-IN M O I MiniDSX-1 Permanent Equipment Cable Network Element B Tx OUT X-OUT X-IN Rx IN OUT MON MON IN MON OUT IN R T T R R2 R2 GND S -48V -48V LED RED TL OUT TN RN TN IN RN IN OUT ACCEPTS BANTAM PLUGS MiniDSX-1 Jack Schematic Cross-Connect Signal Flow Introduction 309 6/04 • 1247379 MSO Market Solutions www.adc.com • +1-952-938-8080 • 1-800-366-3891 309 Digital Signal Cross-Connect - DS1 MiniDSX-1 Cross-Connect Front Front Front Rear Rear Rear Front Total Module Positions 6 6 3 3 3 3 1 Ordering Information IN/OUT Cabling Wire-wrap RJ48X DB15 Wire-wrap DB15 Wire-wrap Dimensions (HxWxD) 5.25" x 19" x 8" (13.3 x 48.3 x 20.3 cm) 5.25" x 19" x 8" (13.3 x 48.3 x 20.3 cm) 5.25" x 19" x 8" (13.3 x 48.3 x 20.3 cm) 1.75" x 19" x 7.5" (4.5 x 48.3 x 19.1 cm) 1.75" x 19" x 7.5" (4.5 x 48.3 x 19.1 cm) 5.25" x 19" x 8" (13.3 x 48.3 x 20.3 cm) 4" x 6.5" x 5.5" (10.2 x 16.5 x 14.0 cm) Color White Black Black Black Black Black Black Catalog Number Mini-DSX-1/W Mini-DSX-1/WRJ Mini-DSX-1/WD DS-1/3 MPOP-CH* Mini-DSX-1/W-1.75x19 Mini-DSX-D/PRE-X Mini-DSX-1/FA** Features • All chassis are equipped with one eight-termination module • Remaining empty positions are preinstalled with blanks • WECO/EIA mounting brackets *Chassis is not equipped with modules, only blanks. **Designed for wall-mounting; does not require additional modules. 1 234 5678 M O I 19.0" 1 2 3 4 5 6 7 8 1.75" OPEN POSITION FOR FUTURE MODULES OPEN POSITION FOR FUTURE MODULES Mini-DSX-1/W-1.75x19 Front View Up to 24 Terminations 310 6/04 • 1247379 MSO Market Solutions www.adc.com • +1-952-938-8080 • 1-800-366-3891 310 Digital Signal Cross-Connect - DS1 MiniDSX-1 Up to 48 Terminations Mini-DSX-1/W with chassis and Mini-DSX-1/WM Cross-Connect Cabling Front wire-wrap Front wire-wrap Front wire-wrap Rear wire-wrap Rear wire-wrap Internally cross-connected Ordering Information IN/OUT Cabling Wire-wrap RJ48X DB15 Wire-wrap Wire-wrap DB15; 4 receptacles and 4 plugs Color White Black Black Black Black Black Circuit Count 8 8 8 8 8 8 Compatible Chassis Catalog Number Mini-DSX-1/W Mini-DSX-1/WRJ Mini-DSX-1/WD DS-1/3 MPOP-CH Mini-DSX-1/W-1.75x19 Mini-DSX-D/PRE-X Module Catalog Number Mini-DSX-1/WM Mini-DSX-1/WMRJ Mini-DSX-1/WMD DS-1/3 MPOP-H Mini-DSX-1/WM-1.75x19 Mini-DSX-MD-PRE-X Features • Additional modules may be ordered for each chassis • Rear IN/OUT cabling • Modules are mounted into a compatible 19-inch chassis • No LEDs 311 6/04 • 1247379 MSO Market Solutions www.adc.com • +1-952-938-8080 • 1-800-366-3891 311 Digital Signal Cross-Connect - DS1 DSXi ™ – Introduction ADC’s DSX i is the next generation of panels for digital signal cross-connect in T1 networks. DSXi panels have improved density and manageability – making this the preferred choice in fixed-circuit DSX-1 equipment. Providing individual panel configurations for specific network needs, DSXi can be ordered online and shipped within 48 hours with our Instant Delivery Program. It’s connecting on a whole new level. Features Increased density Up to 27 percent greater bay density, saving valuable floor space. Innovative design Easier circuit access and faster identification to help save time and money. Ingenious cable management Ensures cables are kept well organized. Incredibly reliable panels Designed to comply with NEBS Level 3 standards and backed by a lifetime warranty. Individual configurations for individual needs Configurable to meet specific network needs. Instant delivery program Most orders shipped within 48 hours. DSX i ™ Panel Design Enhancements Jumper rings for maximum cable management Large circuit identification cards Wire wrap connectors Circuit identification label Plenty of labeling space Increased Density Sleek, ergonomic design Smaller, brighter LEDs Every circuit is numbered, with key circuits bolded Conveniently located catalog number Physical and visual separations between monitor and IN/OUT ports Front View Rear View 312 6/04 • 1247379 MSO Market Solutions www.adc.com • +1-952-938-8080 • 1-800-366-3891 312 Digital Signal Cross-Connect - DS1 DSXi ™ 84-Termination Rear Cross-Connect Panels Features • Improved circuit density by 20 percent with 4-inch-high panels • Two 4-inch by 4-inch (10.2 x 10.2 cm) vertical jumper rings • WECO/EIA mounting brackets • Circuit identification cards with major circuits bolded • Red tracer LEDs for easier circuit identification • Panel color: putty Cross-Connect Rear Rear Rear Rear Rear Rear Ordering Information IN/OUT Cabling Wire wrap Wire wrap 64-pin 64-pin Wire wrap Wire wrap Designation 1-28 A 1-28 B 1-28 C 1-84 1-28 A 1-28 B 1-28 C 1-84 1-28 A 1-28 B 1-28 C 1-84 Dimensions (HxWxD) 4" x 23" x 8" (10.2 x 58.2 x 20.3 cm) 4" x 23" x 8" (10.2 x 58.2 x 20.3 cm) 4" x 23" x 8" (10.2 x 58.2 x 20.3 cm) 4" x 23" x 8" (10.2 x 58.2 x 20.3 cm) 7" x 19" x 8" (17.8 x 48.3 x 20.3 cm) 7" x 19" x 8" (17.8 x 48.3 x 20.3 cm) Mounting Options Flush, 2", 3", 4" recess Flush, 2", 3", 4" recess Flush, 2", 3", 4" recess Flush, 2", 3", 4" recess Flush, 2", 3", 4" recess Flush, 2", 3", 4" recess Catalog Number Di-G2GU1 Di-G2CU1 Di-G3GU1 Di-G3CU1 Di-F2GU1* Di-F2CU1* *Reversible brackets for 19-inch or 23-inch rack-mounting included. Di-G2CU1 Front View Di-G2CU1 Rear View 313 6/04 • 1247379 MSO Market Solutions www.adc.com • +1-952-938-8080 • 1-800-366-3891 313 Digital Signal Cross-Connect - DS1 DSXi ™ 84-Termination Front Cross-Connect Panels Cross-Connect Front split Front split Front split Front split Front below Front below Ordering Information IN/OUT Cabling Wire wrap Wire wrap 64-pin 64-pin Wire wrap Wire wrap Designation 1-28 A 1-28 B 1-28 C 1-84 1-28 A 1-28 B 1-28 C 1-84 1-28 A 1-28 B 1-28 C 1-84 Dimensions (HxWxD) 4" x 23" x 8" (10.2 x 58.2 x 20.3 cm) 4" x 23" x 8" (10.2 x 58.2 x 20.3 cm) 4" x 23" x 8" (10.2 x 58.2 x 20.3 cm) 4" x 23" x 8" (10.2 x 58.2 x 20.3 cm) 7" x 19" x 8" (17.8 x 48.3 x 20.3 cm) 7" x 19" x 8" (17.8 x 48.3 x 20.3 cm) Mounting Options Flush 2", 3", 4", recess Flush 2", 3", 4", recess Flush 2", 3", 4", recess Flush 2", 3", 4", recess Flush 2", 3", 4", recess Flush 2", 3", 4", recess Catalog Number Di-M2GU1 Di-M2CU1 Di-M3GU1 Di-M3CU1 Di-T2GU1* Di-T2CU1* Features • Increased circuit density by 20 percent with 4-inch-high panels • Two 2-inch by 4-inch (5.1 x 10.2 cm) vertical jumper rings • Circuit identification cards with major circuits bolded • WECO/EIA mounting brackets • Red tracer LEDs for easier circuit identification • Panel color: putty *Reversible brackets for 19-inch or 23-inch rack-mounting included. Di-M2GU1 Front View Di-M2GU1 Rear View 314 6/04 • 1247379 MSO Market Solutions www.adc.com • +1-952-938-8080 • 1-800-366-3891 314 Digital Signal Cross-Connect - DS1 Bantam Plugs .44" (11.18 mm) .250" (6.35 mm) 2.036" (51.71 mm) 1.144" (29.06 mm) 3.203" (81.36 mm) Terminating Plug Short Profile Terminating Plug Looping Plug .312" (7.92 mm) DIA .31" (7.88 mm) DIA .24" DIA (6.10 mm) .5" (12.7 mm) .865" (21.97 mm) 1.365" (34.67 mm) .285" (7.24 mm) .173" (4.39 mm) .02'' (.5 mm) .865" (21.97 mm) 2.625" (66.67 mm) .312" (7.92 mm) 1.75" (44.45 mm) Conversion Plugs Conversion plugs provide a means to interface longframe [310] jacks to bantam jacks. The rear of the longframe plug is modified to accept either two-conductor or three-conductor bantam plugs. Hole Plugs The bantam hole plug is used to fill unused jack positions or to complete a panel when jacks are to be added at a later date. Looping Plugs Bantam looping plugs are used to “loop” OUT jacks to IN jacks at the DSX. The plug conductors are strapped internally. The three-conductor plugs are wired tip to tip, ring to ring and sleeve to sleeve. Terminating Plugs The bantam terminating plug is used to terminate a circuit with a specific load. It has an integrated 0.5 watt ± 1 percent resistor. The plug shell is marked with the resistance value. Other resistance values available on special order. Dummy Plugs When bantam dummy plugs are inserted into jack circuits, they actuate the circuit contacts and do not carry a signal. .860" (21.84 mm) Three-Conductor 1.209" (30.71 mm) 3.406" (86.51 mm) .25" (6.35 mm) .55" (13.97 mm) 1.144" (29.06 mm) 3.203" (81.36 mm) .25" (6.35 mm) .44" (11.18 mm) Two-Conductor Conversion Plug Three-Conductor Conversion Plug 315 6/04 • 1247379 MSO Market Solutions www.adc.com • +1-952-938-8080 • 1-800-366-3891 315 Digital Signal Cross-Connect - DS1 DSXi ™ 84-Termination Total Front Access Panels Cross-Connect Total front access Total front access Ordering Information IN/OUT Cabling Wire wrap Wire wrap Designation 1-28 A 1-28 B 1-28 C 1-84 Dimensions (HxWxD) 6" x 23" x 8" (15.2 x 58.2 x 20.3 cm) 6" x 23" x 8" (15.2 x 58.2 x 20.3 cm) Mounting Options Flush 2", 3", 4", recess Flush 2", 3", 4", recess Catalog Number Di-X2GU1 Di-X2CU1 Features • Increased circuit density by 14 percent with 6-inch-high panels • Two 2-inch by 4-inch (5.1 x 10.2 cm) vertical jumper rings • Circuit identification cards with major circuits bolded • WECO/EIA mounting brackets • Red tracer LEDs for easier circuit identification • Front cross-connect and network equipment cable interface • Panel color: putty 316 6/04 • 1247379 MSO Market Solutions www.adc.com • +1-952-938-8080 • 1-800-366-3891 316 Digital Signal Cross-Connect - DS1 Bantam Plugs Circuit Guard Plugs Circuit guard plugs snap-fit into bantam jacks, but do not actuate the circuit. • Single circuit guard plugs identify and block entry to critical circuits. • Quad circuit guard plugs cover the send and receive sides of a four-wire circuit, yet leave the monitor jacks open. They feature a clear window and white designation card. • Dual circuit guard plugs cover the IN and OUT jacks. They feature a plastic window and designation card, and are offered in kits of 25. .480" (12.19 mm) .22" (5.59 mm) .290" (7.37 mm) DIA. .183" (4.65 mm) DIA. .465" (11.81 mm) .266" (6.67 mm) .612" ( 15.54 mm) .312" (7.92 mm) .14" (3.56 mm) .05" (1.27 mm) .06" (1.52 mm) .183" (4.65 mm) .15" (3.81 mm) .480" (12.19 mm) .266" (6.67 mm) .160" (4.06 mm) TYP. (2) .610" (15.49 mm) .610" (15.49 mm) .312" (7.92 mm) .15" (3.81 mm) .312" (7.92 mm) .15" (3.81 mm) Single Dual Quad [...]... Plug (kits of 25) Red Black White PJ925R PJ925W PJ925 PJ926R PJ926W PJ926B PLG-100051 PLG-100050 PLG-100052 6/04 • 1247379 MSO Market Solutions Description www.adc.com • +1-952-938-8080 • 1-800-366-3891 317 Digital Signal Cross-Connect - DS1 6/04 • 1247379 MSO Market Solutions Patch Cords – Three-Conductor Bantam patch cords are plastic jacketed, shielded cords with molded-on plugs with molded insulation... 3.78" MAX (96.01 mm) Dual Conversion Patch Cord 6/04 • 1247379 MSO Market Solutions Ordering Information Longframe to Bantam Conversion Cord www.adc.com • +1-952-938-8080 • 1-800-366-3891 319 Digital Signal Cross-Connect - DS3 DSX-3 Minimum Point of Presence DS-3 MPOP-FA Series – Total Front Access 6/04 • 1247379 MSO Market Solutions Supports up to 4 DS3 circuits Rack Mount Chassis Module Wall Mount... 1247379 MSO Market Solutions The common chassis accepts three individual plug-in modules or one CSU and one plug-in module This concept eliminates the need to purchase separate chassis panels for each application www.adc.com • +1-952-938-8080 • 1-800-366-3891 328 Digital Signal Cross-Connect - DS3 Multifunction Panel Plug-In Modules Ordering Information 6/04 • 1247379 MSO Market Solutions Description... Rack-Mounted Chassis RP3-2XWP01 Wall-Mounted Chassis 6/04 • 1247379 MSO Market Solutions Rack-Mounted Chassis with integrated heat baffle Supports 24 modules (includes cable rings) Cable Rings Wall-Mount Chassis with extension brackets www.adc.com • +1-952-938-8080 Module • 1-800-366-3891 334 Digital Signal Cross-Connect Relay Racks MSO Market Solutions Relay Racks feature universal hole patterns on the side,... available with modular pre-termination, you’ll find that ADC leads the way Again, RZX-3 sets the new standard www.adc.com • +1-952-938-8080 • 1-800-366-3891 323 Digital Signal Cross-Connect - DS3 RZX-3 – Individual Modules 6/04 • 1247379 MSO Market Solutions DSX-4R modules have rear BNC connectors staggered high and low across the chassis in order to obtain the ultimate in system density Modules may be... With its basic architecture, RZX-3 is ideal for any 19-inch or 23-inch mounting arrangement in racks or cabinets www.adc.com • +1-952-938-8080 • 1-800-366-3891 324 Digital Signal Cross-Connect - DS3 RZX-3 – Unloaded Chassis 4" MSO Market Solutions 19" Without Adapters 23" With Adapters 12" to 15" Adjustable Depth 32-Position Unloaded Chassis Front View 32-Position Unloaded Chassis Rear View Description... install and remove BNC connectors because of extreme high density Please contact your ADC sales representative www.adc.com • +1-952-938-8080 • 1-800-366-3891 325 Digital Signal Cross-Connect - DS3 RZX-3 – Loaded Chassis Features: MSO Market Solutions • • • 19-inch mounting (23-inch adapters included with each chassis) Flush and 2-inch recess mounting option Red flashing LED on front of chassis (optional... insertion/withdrawal tool (BT2000) is recommended to install and remove BNC connectors Please contact your ADC sales representative www.adc.com • +1-952-938-8080 • 1-800-366-3891 326 Digital Signal Cross-Connect - DS3 MSO Market Solutions Multifunction Panel Multifunction swing-out universal chassis loaded with a fiber, DS1 and DS3 module The compact, modular universal multifunction chassis provides a point... connections • 8 termination DSX-1 cross-connect modules available in wire-wrap or RJ IN/OUT connections • 1 circuit DS3 MPOP interconnect module with a modular design for growth up to 3 DS3 circuits • Fiber connector module • CSU mounting shelf • Fuse and alarm module 6/04 • 1247379 • 8 termination monitor module www.adc.com • +1-952-938-8080 • 1-800-366-3891 327 Digital Signal Cross-Connect - DS3 Multifunction... 1.75" x 23" x 7.5" (4.45 x 58.42 x 19.05 cm) depth includes 3" (7.62 cm) cable tray +1-952-938-8080 • DS-3 MPOP-FA-23 1-800-366-3891 320 Digital Signal Cross-Connect - DS3 DSX-3 Minimum Point of Presence DS-3 MPOP-RAH Series – Rear Access 6/04 • 1247379 MSO Market Solutions Supports up to 6 DS3 circuits Features • Each horizontally mounted two position module interconnects four network elements (two . 1-800-366-3891 307 Digital Signal Cross-Connect Solutions DS1 Signal Rate MiniDSX-1 Front and Rear Cross-Connect 308 DSXi ™ 84-Termination Cross-Connect Panels. Schematic Cross-Connect Signal Flow Introduction 309 6/04 • 1247379 MSO Market Solutions www.adc.com • +1-952-938-8080 • 1-800-366-3891 309 Digital Signal Cross-Connect