1. Trang chủ
  2. » Kỹ Thuật - Công Nghệ

Clevo P650RE6( g) P651RE6( g) P650RE3( g) P651RE3( g) service manual

134 36 0

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 134
Dung lượng 10,62 MB

Nội dung

P650RE6(-G) / P651RE6(-G) / P650RE3(-G) / P651RE3(-G) Preface Notebook Computer P650RE6(-G) / P651RE6(-G) / P650RE3(-G) / P651RE3(-G) Service Manual Preface I Preface Notice The company reserves the right to revise this publication or to change its contents without notice Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes Preface Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer Version 1.0 November 2015 Trademarks Intel and Intel Core are trademarks of Intel Corporation Windows® is a registered trademark of Microsoft Corporation Other brand and product names are trademarks and /or registered trademarks of their respective companies II Preface About this Manual This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and inspection of personal computers It is organized to allow you to look up basic information for servicing and/or upgrading components of the P650RE6(G) / P651RE6(-G) / P650RE3(-G) / P651RE3(-G) series notebook PC The following information is included: Chapter 1, Introduction, provides general information about the location of system elements and their specifications Chapter 2, Disassembly, provides step-by-step instructions for disassembling parts and subsystems and how to upgrade elements of the system Preface Appendix A, Part Lists Appendix B, Schematic Diagrams Appendix C, Updating the FLASH ROM BIOS III Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool Avoid using a telephone (other than a cordless type) during an electrical storm There may be a remote risk of electrical shock from lightning Do not use the telephone to report a gas leak in the vicinity of the leak Use only the power cord and batteries indicated in this manual Do not dispose of batteries in a fire They may explode Check with local codes for possible special disposal instructions This product is intended to be supplied by a Listed Power Unit as follows: Preface • AC Input of 100 - 240V, 50 - 60Hz, DC Output of 19.5V, 9.23A (180 Watts) minimum AC/DC Adapter FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: This device may not cause harmful interference This device must accept any interference received, including interference that may cause undesired operation IV Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged To prevent this, follow these suggestions: Don’t drop it, or expose it to shock If the computer falls, the case and the components could be damaged Do not expose the computer to any shock or vibration Do not place anything heavy on the computer Keep it dry, and don’t overheat it Keep the computer and power supply away from any kind of heating element This is an electrical appliance If water or any other liquid gets into it, the computer could be badly damaged Do not leave it in a place where foreign matter or moisture may affect the system Don’t use or store the computer in a humid environment Do not place the computer on any surface which will block the vents Preface Do not expose it to excessive heat or direct sunlight Do not place it on an unstable surface Follow the proper working procedures for the computer Shut the computer down properly and don’t forget to save your work Remember to periodically save your data as data may be lost if the battery is depleted Do not turn off the power until you properly shut down all programs Do not turn off any peripheral devices when the computer is on Do not disassemble the computer by yourself Perform routine maintenance on your computer V Preface Avoid interference Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields These can hinder proper performance and damage your data Take care when using peripheral devices Use only approved brands of peripherals Unplug the power cord before attaching peripheral devices Preface Power Safety The computer has specific power requirements:  VI • • Power Safety Warning • Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord) It is advisable to also remove your battery in order to prevent accidentally turning the machine on • • • Only use a power adapter approved for use with this computer Your AC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply If you are unsure of your local power specifications, consult your service representative or local power company The power adapter may have either a 2-prong or a 3-prong grounded plug The third prong is an important safety feature; not defeat its purpose If you not have access to a compatible outlet, have a qualified electrician install one When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices Before cleaning the computer, make sure it is disconnected from any external power supplies Do not plug in the power cord if you are wet Do not use the power cord if it is broken Do not place heavy objects on the power cord Preface Battery Precautions • Only use batteries designed for this computer The wrong battery type may explode, leak or damage the computer • Do not continue to use a battery that has been dropped, or that appears damaged (e.g bent or twisted) in any way Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire • Recharge the batteries using the notebook’s system Incorrect recharging may make the battery explode • Do not try to repair a battery pack Refer any battery pack repair or replacement to your service representative or qualified service personnel • Keep children away from, and promptly dispose of a damaged battery Always dispose of batteries carefully Batteries may explode or leak if exposed to fire, or improperly handled or discarded • Keep the battery away from metal appliances • Affix tape to the battery contacts before disposing of the battery • Do not touch the battery contacts with your hands or metal objects Battery Guidelines Preface The following can also apply to any backup batteries you may have • If you not use the battery for an extended period, then remove the battery from the computer for storage • Before removing the battery for storage charge it to 60% - 70% • Check stored batteries at least every months and charge them to 60% - 70%  Battery Disposal The product that you have purchased contains a rechargeable battery The battery is recyclable At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream Check with your local solid waste officials for details in your area for recycling options or proper disposal Caution Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Discard used battery according to the manufacturer’s instructions Battery Level Click the battery icon in the taskbar to see the current battery level and charge status A battery that drops below a level of 10% will not allow the computer to boot up Make sure that any battery that drops below 10% is recharged within one week VII Preface Related Documents You may also need to consult the following manual for additional information: User’s Manual on CD/DVD This describes the notebook PC’s features and the procedures for operating the computer and its ROM-based setup program It also describes the installation and operation of the utility programs provided with the notebook PC System Startup Remove all packing materials Place the computer on a stable surface Insert the battery and make sure it is locked in position Securely attach any peripherals you want to use with the computer (e.g keyboard and mouse) to their ports Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter Use one hand to raise the lid/LCD to a comfortable viewing angle (do not exceed 135 degrees); use the other hand (as illustrated in Figure 1) to support the base of the computer (Note: Never lift the computer by the lid/LCD) Press the power button to turn the computer “on” Preface 135° Figure Opening the Lid/LCD/ Computer with AC/DC Adapter Plugged-In  Shut Down Note that you should always shut your computer down by choosing the Shut down command in Windows (see below) This will help prevent hard disk or system problems Click the icon in the Start Screen and choose Shut down from the menu Or Right-click the Start button at the bottom of the Start Screen or the Desktop and choose Shut down or sign out > Shut down from the context menu VIII Schematic Diagrams P650RE HDD Board SATA PORT1 HSMB_SDA HSMB_SCK H_SATA_TXP1 H_SATA_TXN1 H_SATA_RXN1 H_SATA_RXP1 H_5V H_5VS H_3.3VS D P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 NC1 NC2 HGND HC13 HC11 *0.01u_16V_X7R_04 10 12 14 16 18 20 22 24 26 28 30 11 13 15 17 19 21 23 25 27 29 11 13 15 17 19 21 23 25 27 29 HGND HSATA_TXP1 HSATA_TXN1 HSATA_RXN1 HSATA_RXP1 HP670RG-M_TPLED D P650RE HDD D01 H_3.3VS 50009-03041-001 P/N = 6-21-C2430-215 PCB Footprint = 50009-0304x *10u_6.3V_X5R_06 H_5VS HGND HGND HC9 HC10 HC12 0.1u_16V_Y5V_04 1u_6.3V_X5R_04 10u_6.3V_X5R_06 + HC8 EEFCX0J221YR 220u,6.3V,ESR=15mȍ,H=1.9mm 220u_6.3V_SMD-D 51824-0227A-001 P/N = 6-20-437J0-022 PCB Footprint = 50887-0220A-XXX For P670RG-M TP LED ᶲẞ HGND HGND Sheet 67 of 79 P650RE HDD Board P650RE HDD D01 H5V_TPLED HU2 H_5V VIN VOUT GND 10u_6.3V_X5R_06 HGND HP670RG-M_TPLED EN# OC# HJ_LEDTP1 100 mil HC18 C HC19 HC21 0.1u_16V_Y5V_04 *10u_6.3V_X5R_06 2 uP7549UMA5-20 PCB Footprint = M-SOT23-5 HR10 HGND PIN16 HGND HGND HU1 HSATA_TXP1 HSATA_TXN1 HC4 HC3 0.01u_16V_X7R_04 0.01u_16V_X7R_04 HSATA_RXN1 HSATA_RXP1 HC2 HC1 0.01u_16V_X7R_04 0.01u_16V_X7R_04 HR11 4.7K_04 AIP AIN From PCH Note: Close to Re-driver IC HOST AOP AON DEVICE BON BOP BIN BIP HR1 *0_04 HR8 *0_04 HTXP1 HSATA_TXN1 HR2 *0_04 HR7 *0_04 HTXN1 HSATA_RXN1 HR3 *0_04 HR5 *0_04 HRXN1 HSATA_RXP1 HR4 *0_04 HR6 *0_04 HRXP1 *100K_04 *100K_04 *100K_04 HR13 HR20 *0_04 *0_04 HR17 2K_1%_04 T-PAD GND GND 21 13 DE_B DE_A HR12 HR21 HR16 H_3.3VS co-lay, place under SN75LVCP601 REXT Note: Close to Re-driver IC B EN 15 14 HTXP1 HTXN1 12 11 HRXN1 HRXP1 HC17 0.01u_16V_X7R_04 H_SATA_TXP1 HC16 0.01u_16V_X7R_04 H_SATA_TXN1 HC15 0.01u_16V_X7R_04 H_SATA_RXN1 HC14 0.01u_16V_X7R_04 H_SATA_RXP1 To Conn SMB_SCK SMB_SDA 1u_6.3V_X5R_04 PIN10 18 19 0.1u_16V_Y5V_04 PIN6 HSATA_TXP1 0_04 HC5 0.01u_16V_X7R_04 HGND HR9 10 16 20 HC7 *0_04 VCC33 VCC33 VCC33 VCC33 Port B HGND H_3.3VS SATA re-driver HC6 C 50501-0060N-001 HGND 17 B.Schematic Diagrams 10 12 14 16 18 20 22 24 26 28 30 HGND P650RE HDD D01 HJ_SATA1 S1 S2 S3 S4 S5 S6 S7 HJ_MB1 ASM1466_new HGND HR15 HR19 *100K_04 *100K_04 HR22 HR23 0_04 0_04 H_3.3VS HSMB_SDA HSMB_SCK P650RE HDD D01 BCN HR14 HR18 *0_04 *0_04 HGND HGND A A HH4 *H6_3D2_3 HH3 *H6_3D2_3 HH1 *H6_3D2_3 1HR HGND HGND *0_04 4HR *0_04 2HR *0_04 5HR *0_04 3HR *0_04 6HR *0_04 ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ Title Size A3 HGND Date: B - 68 P650RE HDD Board [67] P650RE HDD B'd_H Document Number P650RE Rev D01 6-71-P65RN-D01 Monday, July 06, 2015 Sheet 67 of 79 Schematic Diagrams P650RE LED Board LJ_LED1 LLED_ACIN LLED_PWR LLED_BAT_CHG LLED_BAT_FULL LLED_NUM# LLED_CAP# LLED_SCROLL# L_WLAN_AIRPLANE# L_dGPU_LED LSATA_LED# NC1 NC2 LD9 LLED_PWR LR9 A 330_04 LD11 LLED_BAT_FULL C Green LR13 330_04 A C D Green RY-SP260UYG24-5M LD10 LLED_ACIN LR7 A 330_04 RY-SP260UYG24-5M LD12 LLED_BAT_CHG C Amber LR11 330_04 A C Amber RY-SP260USO24-5M LED_GND RY-SP260USO24-5M AC IN/POWER ON LED L_3.3VS BAT CHARGE/FULL LED LED_GND FP225H-012S10M PCB Footprint = fp225-012g LED_GND 1LR *0_04 4LR *0_04 2LR *0_04 5LR *0_04 3LR *0_04 6LR *0_04 L_3.3VS Sheet 68 of 79 P650RE LED Board C C LR3 LR2 LR6 LR5 LR4 330_04 330_04 330_04 LR1 A A A A 330_04 LD3 LD2 RY-SP260UYG24-5M RY-SP260UYG24-5M RY-SP260UYG24-5M dGPU LED SCROLL LOCK LED CAPS LOCK LED NUM LOCK LED AIRPLANE LED HDD LED P650RE LED D02 LR14 *0_04 C LLED_SCROLL# LLED_CAP# LLED_NUM# C LD5 RY-SP260UYG24-5M C LD6 RY-SP260UYG24-5M C LD7 RY-SP260UYG24-5M C LD4 C C A 330_04 A 330_04 L_WLAN_AIRPLANE# LSATA_LED# B L_dGPU_LED E B B LQ1 DTC114EUA LED_GND LH1 *H3_2D2_2 LH4 *H3_2D2_2 LH3 *H6_3D2_3 LH2 *H6_3D2_3 P6504-D03 to P65R4-D01: LQ1ƃᣪ LED_GND LED_GND LED_GND LED_GND ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ A Title Size A4 Date: A [68] P650RE LED BOARD Document Number P650RE Rev 6-71-P65R4-D02 Friday, July 03, 2015 Sheet 68 D02 of 79 P650RE LED Board B - 69 B.Schematic Diagrams 12 11 10 D Schematic Diagrams Finger Sensor Board B.Schematic Diagrams Sheet 69 of 79 Finger Sensor Board F3.3V F2.5V F3.3V FLED1 FMOSI FMCLK FDISCON C F_XOUT 10 F2.5V 11 F3.3V 12 F_RST_N 13 14 15 EGND MODE AVDD DP DVDD VDDIO LED1 SPI_MOSI SPI_MISO DVSS_1 UVSS AVSS_1 RESETN DVSS SGND 29 FUSB_PP 28 FUSB_PN 27 SPI_CS DISCON RVDD D DN LED2 DVDD_1 30 UVDD SPI_CLK XO FJ1 26 FMCS 25 FMISO 24 FLED2 11 13 15 17 19 21 23 F2.5V FMOSI FMCLK FMCS FMISO F3.3V F_XIN F_XOUT F_RST_N 23 F3.3V F3.3V 10 12 14 16 18 20 22 24 FLED1 FLED2 FDISCON FUSB_PN FUSB_PP 22 21 XI SPNZ-24S1-B-017-1-R P/N = 6-21-41700-212 F_XIN FGND FGND 20 AVSS C 19 AVDD_1 F3.3V 18 CLK_SEL NOTE: CLK_SEL CLK_SEL=HIGH (NC) , FREQ=12MHz Crystal CLK_SEL=LOW , FREQ=48MHz OSC 17 EGND_2 16 EGND_1 ES603-WB FGND NOTE: MODE MODE=HIGH (NC) , USB MODE MODE=LOW , SPI MODE FU1 D FGND B B **GU1๙ሒᶵ⎗≈ᛄ⁦,ẍ⃵ᶲẞࠤ₅ཷ FJ1 23 24 BOTTON VIEW 23 24 TOP VIEW ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ A Title Size A4 Date: B - 70 Finger Sensor Board A [69] FINGER SENSOR BOARD Document Number P650RE Rev D01B 6-71-P650F-D01B Friday, July 03, 2015 Sheet 69 of 79 Schematic Diagrams P650RE Click Board T_TP_VCC TJ_MB TR5 TR6 27.4_1%_04 27.4_1%_04 TUSB_PN10 TUSB_PP10 TO M/B TGND FP226H-004S10M PCB Footprint = fp226h-004xxxm_r T_TP_CLK T_TP_DATA T_TP_BTN_L T_TP_BTN_R T_TP_SMB_CLK T_TP_SMB_DAT TD1 FP225H-008S10M fp225h-008gxxxm_r T_TP_DATA T_TP_CLK T_TP_SMB_DAT T_TP_SMB_CLK 50501-0060N-001 88511-06R TD3 6-20-94K30-108 TC9 TH2 H7_0D3_7 0.1u_10V_X7R_04 *V15AVLC0402 D TGND 4 T_TP_VCC TJ_FP1 NC1 NC2 TO T/P PIN TH1 H7_0D3_7 TGND TGND TD4 TD2 *V15AVLC0402 FP226H-004S10M JXT_FP226H-004XXAM T_TP_BTN_R T_TP_BTN_L *V15AVLC0402 2 NC1 NC2 TO BOTTOM/B TJ_TP1 TL1 FCM1005KF-121T03 W/O FP໚⊛⎒ᶲᏼ⋨᡾ẞ TJ_CLICK *V15AVLC0402 T3.3V D TGND D02 TGND TGND TGND T3.3V TU1 TC8 TUSB_PP10 0.1u_10V_X7R_04 VP NC NC VN CH2 CH1 TUSB_PN10 CM1293A-02SO TGND TGND FOR ESD, ᣨᅙFFC CONNECTORඒූ C C T_XIN TR2 TGND 15p_50V_NPO_04 11 13 15 17 19 21 23 T2.5V TMOSI TMCLK TMCS TMISO TGND TX1 HSX321G_12Mhz TC4 TJ_FPB1 T_XOUT 1M_04 T_XIN T_XOUT T_RST_N TC5 15p_50V_NPO_04 T3.3V TGND Sheet 70 of 79 P650RE Click Board 10 12 14 16 18 20 22 24 TLED1 TLED2 TDISCON NOTE: MODE MODE=HIGH (NC) , USB MODE MODE=LOW , SPI MODE TUSB_PN10 TUSB_PP10 *CON24A QPOFZ-24R2-XD-Z-LD TGND TGND TGND Place Botton B B T2.5V T3.3V TC3 TC7 TC1 TC6 0.1u_10V_X7R_04 4.7u_6.3V_X5R_06 0.1u_10V_X7R_04 4.7u_6.3V_X5R_06 TLED1 TR3 10K_04 TLED2 TR4 10K_04 TGND TGND NOTE: CLK_SEL CLK_SEL=HIGH (NC) , FREQ=12MHz Crystal CLK_SEL=LOW , FREQ=48MHz OSC TGND T3.3V S CLOSE TO SENSOR POWER PIN G D TUSB_PP10 TR7 1.5K_04 TR1 47K_04 TDISCON TQ1 AO3415 1TR *0_04 4TR *0_04 2TR *0_04 5TR *0_04 3TR *0_04 6TR *0_04 A A T3.3V T_RST_N TC2 1u_6.3V_X5R_04 Title Size A3 TGND Date: ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ [70] P650RE CLICK BOARD Document Number P650RE Rev D02 6-71-P65R2-D02 Friday, July 03, 2015 Sheet 70 of 79 P650RE Click Board B - 71 B.Schematic Diagrams It is strongly recommended that the TESD_GND has a dedicated connection to the system chassis or cable shield Schematic Diagrams P650RE USB Board 1/3 LAN (RTL8411B) KR80 0_06 2.49K_1%_04 La KREGOUT KL4 KGND KGND *1K_04 KR69 10K_04 KXTAL2 KXTAL1 KX1 C286-001_25MHZ PCB Footprint = FSX3M KC72 KC71 15p_50V_NPO_04 15p_50V_NPO_04 P65RE USB D02 KPCIE_W AKE# KLAN_W AKEUP# E_PAD KGND KLAN_MDIP1 KLAN_MDIN1 KLAN_MDIP2 KLAN_MDIN2 KVDD10 KLAN_MDIP3 KLAN_MDIN3 B KAVDD33 K3.3VS MDIP0 MDIN0 AVDD10 MDIP1 MDIN1 MDIP2 MDIN2 AVDD10 MDIP3 MDIN3 HV_GIGA VDD3 0.1u_16V_Y5V_04 RTL8411B QFN48 BIOS pulls high or low to GPO pin, Pkease refer to LAN/PHY Disable Application Note KR39 1K_04 KC59 0.1u_16V_Y5V_04 36 35 34 33 32 31 30 29 28 27 26 25 REG_OUT VDDREG ENSWREG VDD1 VD33 ISOLATEBPIN PERSTBPIN CLKREQBPIN MS_BS/SD_WP# DV33_18 HSON HSOP KREGOUT KREGOUT KD3V3 KENSW REG KISOLATEB KPERSTB KR31 KCLKREQB KMS_BS/SD_W P# KRTL8411B_HSON KRTL8411B_HSOP Remind that R109 using the main power (S0 power) KVDD10 KAVDD33 0.1u_16V_Y5V_04 PIN3 *0402_short KVDD33/18 0.1u_16V_Y5V_04 PIN8 72 KR22 0_04 0.1u_10V_X7R_04 0.1u_10V_X7R_04 KPCIE_RXN5_GLAN KPCIE_RXP5_GLAN GIGA LAN KENSW REG KR55 KEVDD10 KCLK_PCIE_GLAN# KCLK_PCIE_GLAN 72 72 KPCIE_TXN5_GLAN KPCIE_TXP5_GLAN 72 72 KCARD_3V3 0.2R 5% SMD0603 40 mil KR2 0.1u_16V_Y5V_04 PIN46 *150_06 *28mil short-p KLAN_MDIN0 KLAN_MDIP0 KLAN_MDIN1 KLAN_MDIP1 1u_6.3V_X5R_04 PIN20 KGND 12 11 KLAN_MDIN2 KLAN_MDIP2 KLAN_MDIN3 KLAN_MDIP3 KAVDD33 *28mil short-p KC36 KC49 KC62 0.1u_16V_Y5V_04 PIN11 0.1u_16V_Y5V_04 PIN32 0.1u_16V_Y5V_04 PIN48 KL3 *HCB1608KF-121T30 K3.3V KGND KD3V3 60 mil KR74 GND1 GND2 GND3 GND4 KGND 0_04 KSD_D0/MS_D1_R KR95 0_04 KSD_D1_R KSD_D2/MS_CLK KR96 0_04 KSD_D2/MS_CLK_R KSD_CLK/MS_D0 KR97 0_04 KSD_CLK/MS_D0_R KSD_D3/MS_D3 0_04 KSD_D3/MS_D3_R KR98 ໸ℏӼ Close to chip B KC87 KC88 KC89 KC90 KC91 KC92 KGND KGND KGND KGND KGND KC7 KC8 KC9 0.1u_16V_Y5V_04 2.2u_6.3V_X5R_04 2.2u_6.3V_X5R_04 C Near Cardreader CONN 10 40 mil TD4TD4+ TD3TD3+ MX4MX4+ MX3MX3+ TD2TD2+ TD1TD1+ MX2MX2+ MX1MX1+ TCT4 TCT3 TCT2 TCT1 MCT4 MCT3 MCT2 MCT1 13 14 16 17 19 20 22 23 KGND 0.01u_16V_X7R_04 KC58 KDLMX1- KLMX1KLMX1+ KLMX2KLMX2+ KJ_RJ1 KDLMX1+ KDLMX1- KDLMX2+ KDLMX2- KDLMX2+ *W CM2012F2S-161T03 KR104 0_04 KR103 0_04 KL8 KDLMX3- KLMX3KLMX3+ KLMX4KLMX4+ KDLMX3+ KDLMX3- KDLMX4+ KDLMX4- KDLMX3+ *W CM2012F2S-161T03 KR102 0_04 KR101 0_04 KL9 KDLMX4- 15 18 21 24 LDO Mode KGND DA+ DADB+ DB- GND1 GND2 shield shield 1KR *0_04 4KR *0_04 2KR *0_04 5KR *0_04 3KR *0_04 6KR *0_04 72 72,73 72 KVDD3 K3.3V K3.3VS KGND DC+ DCDD+ DDP JS-08SO1B P/N = 6-21-B40C0-008 PCB Footprint = PJS-08SL3B D P65RE USB D02 KDLMX4+ *W CM2012F2S-161T03 P65RE USB D02Aዷባᾖෑ2 USB Conᷳ᜛ἕឞ KC75 *28mil short-p KC60 0_04 0_04 KDLMX1+ *W CM2012F2S-161T03 KR106 0_04 KR105 0_04 KL6 KDLMX2- NS892402 KGND SD_C/D ៘ᱠ SD Card Remove Fall time less than ms when SD card remove KL7 D GND1 GND2 GND3 GND4 SD_WP KVCC_CARD KR100 KR99 KL5 KC29 KR64 KR94 KSD_D1 KVCC_CARD KGND 0_06 KR51 SD_DATA1 KGND KGND KGND KVDD3 KSD_D0/MS_D1 KGND 0.1u_16V_Y5V_04 Pin#27 0.1u_16V_Y5V_04 PIN20 SD_DATA0 KGND KC33 VDD3 meet rising time >1ms KSD_CMD/MS_D2_R KAVDD33 KGND KC30 0_04 0_04 Near Cardreader CONN KR1 SD_VSS2 CM2S-061-H-N PCB Footprint = SD-10395-001-3 KSD_CMD/MS_D2 KR93 *0_04 PULL LOW: LDO Mode KVDD33/18 KR13 P11 ࠝEMI⅒కФ,ෑSHORT KEVDD10 KVDD10 72 72 72 PULL HIGH: SWR Mode KGND KGND KSD_CD# 13 14 15 16 17 18 19 20 21 22 23 24 KSD_D1 KSD_D0/MS_D1 KSD_CLK/MS_D0 KSD_CMD/MS_D2 KSD_D3/MS_D3 KSD_D2/MS_CLK 0.1u_16V_Y5V_04 PIN32 KC31 *2.2u_6.3V_X5R_04 Pin#27 KLAN_CLKREQ# LAN_CLKREQ#Țᶵἧ᷀⎗๏ᜓ,๔PCH⎇ᾌఽPULL DOWN KC61 KGND KVDD33/18 P10 SD_CLK *10K_04 KBUF_PLT_RST# KC25 KC26 KMS_BS/SD_W P# KGND capacitors must be close to pin side KVDD10 KC51 KGND P8 SD_VDD KR23 KGND 0.1u_16V_Y5V_04 KGND KSD_D1_R K3.3VS KR38 15K_04 KC6 C P7 K3.3VS KR54 KCARD_3V3 KC39 KSD_D0/MS_D1_R A SD_VSS1 *5p_50V_NPO_04 RTL8411B KC52 P6 T87 T86 SD_CMD *5p_50V_NPO_04 KGND KVDD10 P5 SD_DATA3 *5p_50V_NPO_04 0.1u_16V_Y5V_04 PIN12 KVDD10 KSD_CLK/MS_D0_R SD_DATA2 *5p_50V_NPO_04 KC34 KVDD10 P2 P4 TO EC8587 PIN123 LAN_WAKEUP# CARD_3V3 SD_D1 SD_D0/MS_D1 SD_CLK/MS_D0 SD_CMD/MS_D2 SD_D3/MS_D3 SD_D2/MS_CLK VDDTX HSIP HSIN REFCLK_P REFCLK_N KVDD10 KSD_CMD/MS_D2_R *5p_50V_NPO_04 Sheet 71 of 79 P650RE USB Board 1/3 10 11 12 P1 KVCC_CARD ፗᶺ⅒కࠤᢃៃ,ෑSHORT᡾ẞ KC85 KLED1/GPO KLED2 P9 KSD_D3/MS_D3_R P3 72 KLAN_W AKEUP# KSD_D2/MS_CLK_R KGND LDO Mode໚: La,Ca,Cb ᶵᶲẞ,Raᶲẞ 72 KGND KLAN_MDIP0 KLAN_MDIN0 KC64 *0.1u_16V_Y5V_04 *5p_50V_NPO_04 B.Schematic Diagrams KGND TO SB PCH WAKE# 48 47 46 45 44 43 42 41 40 39 38 37 KU5 49 KAVDD33 A RB751S-40C2 HV_GIGA RSET LV_CEN CKXTAL2 CKXTAL1 MS_CD# SD_CD# LED0 LED_CR LANWAKEB LED1/GPO LED2 KGND C KD5 Cb KGND P65RE USB D02 KGND Ca KC66 *4.7u_6.3V_X5R_06 FOR S5 WAKE UP ON LAN T85 KAVDD33 KXTAL1 KSD_CD# KEECS KLED_CR KGND (>20mil) KGND KVDD10 A KJ_CARD1 KVDD10 *SW F2520CF-4R7M-M KR70 KXTAL2 1M_04 KR71 IN SOCKET ဗᶲStandard PUSH PUSH CARD READER KVDD10 (>20mil) KRSET KR77 Switching Regulator close to PIN48 Ra KNMCT_4 KNMCT_3 KNMCT_2 KNMCT_1 KR81 KR83 KR88 KR89 75_1%_04 75_1%_04 75_1%_04 75_1%_04 ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ KNMCT_R KC84 Title [71] P650RE USB BOARD_K 1/3 MA1206CG-101J-202ER *4.7u_6.3V_X5R_06 PIN35 Size A3 *0.1u_16V_Y5V_04 PIN35 Document Number KGND KGND B - 72 P650RE USB Board 1/3 Date: KGND Rev D02A 6-71-P65R3-D02A Tuesday, July 07, 2015 Sheet 71 of 79 Schematic Diagrams P650RE USB Board 2/3 USB3.0 re-driver USB3.0 PORT4 K3.3V *0_04 KR53 2K_1%_04 (MB⎛ᶳ) KUSBVCC3.0_6 *4.7K_04 *4.7K_04 KU3 K5V VIN VOUT D 19 21 *0_04 KR72 *0_04 GND DE_A SW_A RX2+ K_SCK_P4 KC44 0.1u_10V_X7R_04 KUSB3_TXN4 KC43 0.1u_10V_X7R_04 KUSB3_TXP4 11 KC42 0.1u_10V_X7R_04 KUSB3_RXN4 12 KC41 0.1u_10V_X7R_04 KUSB3_RXP4 KR37 10 CHIP_EN# RX2- 18 KR56 EQ_A TYPE_IND# TX2VCC 20 KC67 RX+ TX2+ 13 KC68 0.1u_10V_X7R_04 EN_RXD 0.1u_10V_X7R_04 KRXP4 RX1- TX1+ Reserverd KRXN4 To Conn TX1- SW_B 22 DE_B KC69 KGND SMB_SCK 14 0.1u_10V_X7R_04 15 KTXP4 GND SMB_DATA 16 23 GND KGND *4.7K_04 EN# OC# KR57 KR61 KR66 72,73 KDD_ON# KR28 KGND KC82 KC83 KUSBVCC3.0_6 K3.3V ⚈⍾ᘠco-lay, ⎴ᏽ⍾ᘠᢃё KTXN4_J KUSB_PN4_J KUSB_PP4_J KRXP4_J KC27 KC50 KC47 0.01u_16V_X7R_04 0.1u_10V_X7R_04 1u_6.3V_X5R_04 KRXN4_J USB3.0 Max Trace length Follow Design Guide KGND KGND KUSB_PN4_CON10 KUSB_PP4_CON KGND KL1 KUSB_PP4 *W CM2012F2S-161T03-short 22u_6.3V_X5R_08 KGND KGND SSTX+ SHIELD VBUS SSTXDGND D+ SSRX+ GND_D SSRX- SHIELD GND1 GND2 C Sheet 72 of 79 P650RE USB Board 2/3 KGND 377AH09FZT S4NVCB P/N = 6-20-B4Z40-109 PCB Footprint = 317AH09FZTS4T4CX KD2 KD4 ⍾ᘠco-lay, ⚈ᦹlayout⌒᜛ 22u_6.3V_X5R_08 KJ_USB3_2 KTXP4_J K3.3V KUSB_PN4 D *0402_short From PCH *4.7K_04 *4.7K_04 *4.7K_04 *0.1u_16V_Y5V_04 2A/90mohm CLOSE TO CONNECTOR C KC46 0.1u_16V_Y5V_04 uP7549UMA5-20 PCB Footprint = M-SOT23-5 KGND KGND ASM1464 PCB Footprint = QFN24-4X4MM KC45 2 KUSB_PN4_J KUSB_PP4_J KTXP4 KTXN4 KGND KRXP4 KRXN4 KGND PUSB3F96 10 KTXP4_J KTXN4_J KGND KRXP4_J KRXN4_J PUSB3F96 LAN BOARD KH7 *H7_5D2_8 (⏓USB3.0x2, PHONE JACK, SIM) KH9 *H9_5B6_5D2_8 KH8 *H9_5B6_5D2_8 KH4 *H7_5D2_8 KH2 *H7_0B7_5D2_2 KH1 *H7_0B7_5D2_2 KJ_MB1 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 K5V B KC4 KVDD3 KC5 2.2u_6.3V_X5R_04 0.1u_16V_Y5V_04 KC2 KGND KGND 0.1u_16V_Y5V_04 KGND K3.3V K3.3VS KC3 KC1 0.1u_16V_Y5V_04 0.1u_16V_Y5V_04 KGND KGND KVDD3 K3.3V 73 KUIM_PW R 73 KUIM_DATA 73 KUIM_CLK 73 KUIM_RST A K3.3VS 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 KUSB_PN4 KUSB_PP4 B KUSB3_TXN4 KUSB3_TXP4 KUSB3_RXN4 KUSB3_RXP4 KGND KUSB_PN3 KUSB_PP3 73 73 KUSB3_TXN3 KUSB3_TXP3 KUSB3_RXN3 KUSB3_RXP3 KH6 *H4_2D2_2 73 73 73 73 KGND KH13 *H4_2D2_2 KGND KH12 *H4_2D2_2 KGND KGND KH15 *H4_2D2_2 KCLK_PCIE_GLAN# 71 KCLK_PCIE_GLAN 71 KPCIE_TXN5_GLAN KPCIE_TXP5_GLAN KPCIE_RXN5_GLAN KPCIE_RXP5_GLAN 71 71 71 71 KDETECT_SW 73 KLAN_CLKREQ# 71 KPCIE_W AKE# 71 KLAN_W AKEUP# 71 KBUF_PLT_RST# 71 KDD_ON# 72,73 KGND KGND KGND KGND KGND KH3 *H4_2D2_2 K5V KT1 KT2 KT3 KT4 KT5 KT6 KGND A ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ P65RE USB D02 Title KT7 Size A3 P65SE USB D03 ᾖෑlib ӒҐ Date: 73 KVDD3 71 K3.3V 71,73 K3.3VS 71 51049-08041-001 PCB Footprint = 51049-0804X KGND KGND KH14 *H4_2D2_2 KGND [72] P650RE USB BOARD 2/3 Document Number P650RE Rev D02A 6-71-P65R3-D02A Tuesday, July 07, 2015 Sheet 72 of 79 P650RE USB Board 2/3 B - 73 B.Schematic Diagrams KC70 EQ_B 25 24 K_SDA_P4 GND *4.7K_04 0.1u_10V_X7R_04 17 KR79 KTXN4 VCC KU6 KGND KC28 10u_6.3V_X5R_06 KGND 100 MIL Standard-A KR62 KR58 KR68 Schematic Diagrams P650RE USB Board 3/3 USB3.0 PORT3 USB3.0 re-driver (MB⎛ᶲ) K3.3V KUSBVCC3.0_2 KR32 KR33 KR24 *0_04 KU8 K5V *4.7K_04 *4.7K_04 KC38 10u_6.3V_X5R_06 D KR15 VIN VOUT GND 2K_1%_04 72 KGND KR42 KDD_ON# *0402_short EN# OC# 100 mil KC48 KC40 0.1u_16V_Y5V_04 *0.1u_16V_Y5V_04 uP7549UMA5-20 PCB Footprint = M-SOT23-5 KC54 20 0.1u_10V_X7R_04 KC53 19 GND DE_A SW_A EN_RXD VCC TYPE_IND# CHIP_EN# RX2RX2+ TX2TX2+ KGND KR49 K_SCK_P3 KC24 0.1u_10V_X7R_04 KUSB3_TXN3 72 KC23 0.1u_10V_X7R_04 KUSB3_TXP3 72 10 *4.7K_04 KC81 KGND 22u_6.3V_X5R_08 From PCH KGND KC22 0.1u_10V_X7R_04 KUSB3_RXN3 72 12 KC21 0.1u_10V_X7R_04 KUSB3_RXP3 72 KTXP3_J ⚈⍾ᘠco-lay, ⎴ᏽ⍾ᘠᢃё KTXN3_J KUSB_PN3_J KUSB_PP3_J KRXP3_J K3.3V K3.3V KRXN3_J SSTX+ SHIELD VBUS SSTXDGND D+ SSRX+ GND_D SSRX- SHIELD C KR20 *0_04 KR41 *0_04 KR16 KR21 KR30 *4.7K_04 *4.7K_04 *4.7K_04 KGND KJ_USB3_1 11 ASM1464 PCB Footprint = QFN24-4X4MM 22u_6.3V_X5R_08 KC80 KUSBVCC3.0_2 Standard-A 0.1u_10V_X7R_04 KRXP3 VCC Sheet 73 of 79 P650RE USB Board 3/3 KRXN3 RX+ 13 To Conn RX1- TX1+ Reserverd 21 SW_B 22 DE_B KC55 SMB_SCK 14 0.1u_10V_X7R_04 TX1- 15 KTXP3 GND SMB_DATA 16 23 EQ_B KC56 GND 0.1u_10V_X7R_04 17 K_SDA_P3 *4.7K_04 KTXN3 18 KC65 KC63 KC57 0.01u_16V_X7R_04 0.1u_10V_X7R_04 1u_6.3V_X5R_04 GND1 GND2 C 377AH09FZT S4NVCB KGND P/N = 6-20-B4Z40-109 PCB Footprint = 317AH09FZTS4T4CX KGND USB3.0 Max Trace length Follow Design Guide KD3 KGND KGND ⍾ᘠco-lay, ⚈ᦹlayout⌒᜛ 72 KUSB_PN3 72 KUSB_PP3 KL2 *W CM2012F2S-161T03-short KUSB_PN3_CON10 KUSB_PP3_CON KGND KUSB_PN3_J KUSB_PP3_J KGND PUSB3F96 KD6 KTXP3 KTXN3 KRXP3 KRXN3 KGND 10 KTXP3_J KTXN3_J KGND KRXP3_J KRXN3_J PUSB3F96 B KR86 B Layout໚ SIMᷳ૘ྡᾉߧ♲≈┯(10mil) ૘ྡᾉߧ♲ᷳ᜛≈GND SIM hold ࿄ᱜ⚃␐≈GND⚵⛶ 4.SIM CONN ᣨᅙ MINI CARD CONN SIMᷳᑧᶨᾉߧ♲ἜLayoutཙ♲ᢈҧ๔10℔↮ SIM CONN *4.7K_04 KJ_SIM1 KDETECT_SW KR82 KDETECT_SW 0_04 (TOP VIEW) KR85 *0402_short KUIM_CLK KUIM_RST 72 72 KUIM_CLK KUIM_RST 72 KUIM_PW R KUIM_CLK_R SW1 C4 C3 C2 C1 KUIM_PW R DETECT_SW UIM_DATA UIM_CLK UIM_RST UIM_PWR UIM_MCMD UIM_I/O UIM_VPP UIM_GND C8 C7 C6 C5 KR84 *0402_short KUIM_DATA_R GNG GND GND GND 72 A KGND KGND PCB Footprint = msmps-s02-xxr P/N = 6-86-2B010-003 KC74 *22p_50V_NPO_04 SIMLOCK MEGA SIM W / SW STANDARD KC77 *22p_50V_NPO_04 KUIM_DATA KUIM_VPP KC76 GND1 GND2 GND3 GND4 B.Schematic Diagrams 25 24 EQ_A KU2 KR44 KGND 2A/90mohm KGND KGND D *22p_50V_NPO_04 KGND KUIM_DATA 72 KC78 *22p_50V_NPO_04 A KGND KGND MSMPS-S02 ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ Title K5V 72 K3.3V 71,72 K3.3VS 71,72 Size A3 Date: B - 74 [73] P650RE USB BOARD 3/3 Document Number P650RE Rev D02A 6-71-P65R3-D02A Tuesday, July 07, 2015 Sheet 73 of 79 Schematic Diagrams P670RE USB Board 1/3 LAN (RTL8411B) Crystal ෑ᷀5032 SIZE ZR44 ZRSET ZR33 2.49K_1%_04 ZR37 *1K_04 ZREGOUT ZAVDD33 ZR41 ZVDD10 ZXTAL2 ZXTAL1 ZX1 C286-001_25MHZ PCB Footprint = FSX3M ZC41 ZC44 15p_50V_NPO_04 15p_50V_NPO_04 P67RE USB D02 A RB751S-40C2 ZPCIE_W AKE# ZLAN_W AKEUP# ZLED1/GPO ZLED2 ZLAN_W AKEUP# ZGND ZLAN_MDIP3 ZLAN_MDIN3 MDIP0 MDIN0 AVDD10 MDIP1 MDIN1 MDIP2 MDIN2 AVDD10 MDIP3 MDIN3 HV_GIGA VDD3 QFN48 ZC39 P2 ZISOLATEB ZPERSTB ZR52 ZCLKREQB ZMS_BS/SD_W P# ZRTL8411B_HSON ZRTL8411B_HSOP 1K_04 Z3.3VS 0.1u_16V_Y5V_04 PIN46 ZGND ZVDD33/18 ZC67 ZC65 *4.7u_6.3V_X5R_06 Pin#27 ZGND ZGND ZVDD10 ZAVDD33 ZGND *0402_short ZBUF_PLT_RST# 75 ZR68 0_04 ZLAN_CLKREQ# 75 LAN_CLKREQ#Țᶵἧ᷀⎗๏ᜓ,๔PCH⎇ᾌఽPULL DOWN ZC52 ZC50 0.1u_10V_X7R_04 0.1u_10V_X7R_04 ZPCIE_RXN5_GLAN ZPCIE_RXP5_GLAN ZENSW REG ZR54 GIGA LAN ZCLK_PCIE_GLAN# ZCLK_PCIE_GLAN 75 75 ZPCIE_TXN5_GLAN ZPCIE_TXP5_GLAN 75 75 75 75 ZR67 0_04 ZSD_CMD/MS_D2_R ZR104 0_04 ZSD_D0/MS_D1_R ZSD_D1 ZR105 0_04 ZSD_D1_R ZSD_D2/MS_CLK ZR106 0_04 ZSD_D2/MS_CLK_R ZSD_CLK/MS_D0 ZR107 0_04 ZSD_CLK/MS_D0_R ZSD_D3/MS_D3 0_04 ZSD_D3/MS_D3_R ZCARD_3V3 1u_6.3V_X5R_04 PIN20 ZGND 12 11 ZLAN_MDIN2 ZLAN_MDIP2 ZLAN_MDIN3 ZLAN_MDIP3 ZAVDD33 10 ZC66 ZC38 ZC37 0.1u_16V_Y5V_04 PIN11 0.1u_16V_Y5V_04 PIN32 0.1u_16V_Y5V_04 PIN48 ZGND ZLAN_MDIN0 ZLAN_MDIP0 ZLAN_MDIN1 ZLAN_MDIP1 *28mil short-p D Z3.3V 0.2R 5% SMD0603 ZC23 ZC24 ZC25 0.1u_16V_Y5V_04 4.7u_6.3V_X5R_06 *10u_6.3V_X5R_06 0.1u_16V_Y5V_04 PIN13 40 mil ZGND Sheet 74 of 79 P670RE USB Board 1/3 ZC95 ZC94 ZC93 ZC92 ZC91 ZC98 ZGND ZGND ZGND ZGND ZGND *150_06 ZVCC_CARD SD Card Remove Fall time less than ms when SD card remove ZGND TD4TD4+ TD3TD3+ MX4MX4+ MX3MX3+ TD2TD2+ TD1TD1+ MX2MX2+ MX1MX1+ TCT4 TCT3 TCT2 TCT1 MCT4 MCT3 MCT2 MCT1 13 14 16 17 ZLMX1ZLMX1+ ZLMX2ZLMX2+ 19 20 22 23 ZLMX3ZLMX3+ ZLMX4ZLMX4+ ZGND ZD3V3 C 60 mil ZDLMX2+ *W CM2012F2S-161T03 ZR113 0_04 ZR114 0_04 ZL4 ZDLMX3- ZC63 *4.7u_6.3V_X5R_06 PIN35 *0.1u_16V_Y5V_04 PIN35 ZDLMX3+ ZDLMX3- ZDLMX4+ ZDLMX4- DA+ DADB+ DB- ZGND Z_CHASSIS_GND DC+ DCDD+ DD- 75 ZVDD3 75,76 Z3.3V 75 Z3.3VS ZR24 ZR21 ZR20 ZR19 75_1%_04 75_1%_04 75_1%_04 75_1%_04 P67RE USB D02 1ZR ZNMCT_R *0_04 4ZR *0_04 2ZR *0_04 5ZR *0_04 3ZR *0_04 6ZR *0_04 ZC31 D MA1206CG-101J-202ER ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ 0.1u_16V_Y5V_04 ZC88 *0.1u_16V_Y5V_04 ZC89 0.01u_50V_X7R_04 ZC90 *0.01u_50V_X7R_04 Z_CHASSIS_GND [74] P670RE USB BOARD_Z 1/3 ZGND ZGND GND1 GND2 shield shield P JS-08SO1B P/N = 6-21-B40C0-008 PCB Footprint = PJS-08SL3B ZDLMX4+ *W CM2012F2S-161T03 ZNMCT_4 ZNMCT_3 ZNMCT_2 ZNMCT_1 ZC87 LDO Mode ZC72 ZDLMX3+ *W CM2012F2S-161T03 ZR115 0_04 ZR116 0_04 ZL3 ZDLMX4- ZJ_RJ1 ZDLMX1+ ZDLMX1- ZDLMX2+ ZDLMX2- NS892402 ZC20 40 mil *28mil short-p ZDLMX1- ZDLMX1+ *W CM2012F2S-161T03 ZR111 0_04 ZR112 0_04 ZL6 ZDLMX2- 15 18 21 24 0.01u_16V_X7R_04 ZGND 0_04 0_04 Title GND1 GND2 GND3 GND4 Near Cardreader CONN ZC22 ZC49 0.1u_16V_Y5V_04 PIN20 ZR72 Close to chip ZGND ZVCC_CARD ZL5 ZGND ZL9 *HCB1608KF-121T30 ໸ℏӼ ࠝEMI⅒కФ,ෑSHORT ZGND P67RE USB D02A ὅ‫⓮ݸٽ‬ᶷᢈᓚᾖෑZC20, ZL5᜛ཥ ZR91 ZR108 0_04 PULL LOW: LDO Mode 0.1u_16V_Y5V_04 Pin#27 *28mil short-p SD_C/D CM2S-061-H-N PCB Footprint = SD-10395-001-3 ZSD_D0/MS_D1 *0_04 Near Cardreader CONN 0_06 ZR92 GND1 GND2 GND3 GND4 SD_WP ZGND ZC48 ZVDD3 SD_DATA1 B ZR109 ZR110 ZL7 VDD3 meet rising time >1ms SD_DATA0 ZGND ZEVDD10 ZVDD10 P11 ZSD_CMD/MS_D2 ZR103 ZAVDD33 PULL HIGH: SWR Mode ZGND ZR38 ZSD_CD# ZGND ZGND ZVDD33/18 P10 capacitors must be close to pin side 13 14 15 16 17 18 19 20 21 22 23 24 ZC42 0.1u_16V_Y5V_04 PIN32 ZMS_BS/SD_W P# *5p_50V_NPO_04 ZC64 SD_VSS2 *5p_50V_NPO_04 ZC35 P8 *10K_04 ZR22 0.1u_16V_Y5V_04 PIN8 ZSD_D1_R ZR51 Remind that R109 using the main power (S0 power) ZVDD10 0.1u_16V_Y5V_04 PIN3 P7 Z3.3VS ZR23 ZC36 SD_CLK P6 ZGND ZREGOUT ZD3V3 ZVDD33/18 SD_VDD P5 ZSD_D0/MS_D1_R A SD_VSS1 *5p_50V_NPO_04 ZSD_D1 ZSD_D0/MS_D1 ZSD_CLK/MS_D0 ZSD_CMD/MS_D2 ZSD_D3/MS_D3 ZSD_D2/MS_CLK ZENSW REG C ZGND ZSD_CLK/MS_D0_R ZR69 15K_04 ZREGOUT SD_CMD P4 ZVCC_CARD ZC96 ZC51 0.1u_16V_Y5V_04 36 35 34 33 32 31 30 29 28 27 26 25 SD_DATA3 P3 ፗᶺ⅒కࠤᢃៃ,ෑSHORT᡾ẞ ZR53 REG_OUT VDDREG ENSWREG VDD1 VD33 ISOLATEBPIN PERSTBPIN CLKREQBPIN MS_BS/SD_WP# DV33_18 HSON HSOP SD_DATA2 *5p_50V_NPO_04 ZCARD_3V3 ZVDD10 ZSD_CMD/MS_D2_R ZGND *5p_50V_NPO_04 RTL8411B ZVDD10 P1 *5p_50V_NPO_04 0.1u_16V_Y5V_04 PIN12 ZGND ZVDD10 P9 ZSD_D3/MS_D3_R BIOS pulls high or low to GPO pin, Pkease refer to LAN/PHY Disable Application Note ZEVDD10 ZVDD10 ZAVDD33 Z3.3VS B ZSD_D2/MS_CLK_R *0.1u_16V_Y5V_04 ZT4 ZT5 CARD_3V3 SD_D1 SD_D0/MS_D1 SD_CLK/MS_D0 SD_CMD/MS_D2 SD_D3/MS_D3 SD_D2/MS_CLK VDDTX HSIP HSIN REFCLK_P REFCLK_N ZLAN_MDIP1 ZLAN_MDIN1 ZLAN_MDIP2 ZLAN_MDIN2 10 11 12 ZC70 LDO Mode໚: La,Ca,Cb ᶵᶲẞ,Raᶲẞ 75 ZGND ZLAN_MDIP0 ZLAN_MDIN0 Cb *4.7u_6.3V_X5R_06 Size A3 ‫ޒ⓮ݸ‬೸ᦘᷱ Date: Document Number Rev D02A 6-71-P67R3-D02A Friday, July 03, 2015 Sheet 74 of 79 P670RE USB Board 1/3 B - 75 B.Schematic Diagrams E_PAD ZGND ZVDD10 ZC71 Ca 75 TO SB PCH WAKE# ZJ_CARD1 (>20mil) La TO EC8587 PIN123 LAN_WAKEUP# 48 47 46 45 44 43 42 41 40 39 38 37 ZU4 49 C ZD6 HV_GIGA RSET LV_CEN CKXTAL2 CKXTAL1 MS_CD# SD_CD# LED0 LED_CR LANWAKEB LED1/GPO LED2 ZGND IN SOCKET ဗᶲStandard PUSH PUSH CARD READER ZVDD10 ZVDD10 *SW F2520CF-4R7M-M ZAVDD33 0.1u_16V_Y5V_04 P67RE USB D02 ZGND 10K_04 FOR S5 WAKE UP ON LAN ZT3 ZXTAL1 ZSD_CD# ZEECS ZLED_CR ZGND ZGND ZGND ZL8 A 0_06 (>20mil) ZXTAL2 1M_04 ZGND meet realtek Freq tolerance 50ppm ZR36 Switching Regulator close to PIN48 Ra Schematic Diagrams P670RE USB Board 2/3 USB3.0 re-driver USB3.0 PORT4 Z3.3V *0_04 ZR88 2K_1%_04 (MB⎛ᶲ) ZUSBVCC3.0_6 *4.7K_04 *4.7K_04 ZU2 Z5V VIN VOUT D 0.1u_10V_X7R_04 ZC54 19 Sheet 75 of 79 P670RE USB Board 2/3 GND DE_A SW_A EQ_A TX1+ RX+ TYPE_IND# CHIP_EN# RX2RX2+ TX2VCC ZRXP4 ZGND RX1- TX2+ 13 20 21 EN_RXD ZC53 Reserverd 0.1u_10V_X7R_04 SW_B ZRXN4 To Conn TX1- DE_B 22 GND ZGND SMB_SCK 14 23 ZC56 15 ZC55 0.1u_10V_X7R_04 EQ_B 0.1u_10V_X7R_04 ZTXP4 GND ZTXN4 GND SMB_DATA 16 25 24 Z_SDA_P4 17 *4.7K_04 18 B.Schematic Diagrams ZR43 VCC ZU5 ZGND ZC19 10u_6.3V_X5R_06 ZGND Z_SCK_P4 ZR98 *4.7K_04 ZC78 0.1u_10V_X7R_04 ZUSB3_TXN4 ZC79 0.1u_10V_X7R_04 ZUSB3_TXP4 10 ZGND 75,76 ZR18 ZDD_ON# EN# OC# 100 MIL ZC80 0.1u_10V_X7R_04 ZUSB3_RXN4 12 ZC81 0.1u_10V_X7R_04 ZUSB3_RXP4 *0_04 ZGND ZC7 ZR58 22u_6.3V_X5R_08 ZGND ZJ_USB3_2 ⚈⍾ᘠco-lay, ⎴ᏽ⍾ᘠᢃё Z3.3V *4.7K_04 *4.7K_04 *4.7K_04 22u_6.3V_X5R_08 ZC10 ZTXP4_J ZR85 ZR77 ZR65 D 2A/90mohm ZTXN4_J ZUSB_PN4_J ZUSB_PP4_J ZRXP4_J ZR86 C *0.1u_16V_Y5V_04 uP7549UMA5-20 PCB Footprint = M-SOT23-5 *0402_short ZUSBVCC3.0_6 Z3.3V ASM1464 PCB Footprint = QFN24-4X4MM ZC8 0.1u_16V_Y5V_04 From PCH ZGND 11 ZC6 ZC68 ZC57 ZC82 0.01u_16V_X7R_04 0.1u_10V_X7R_04 1u_6.3V_X5R_04 ZRXN4_J Standard-A ZR70 ZR79 ZR60 SSTX+ SHIELD VBUS SSTXDGND D+ SSRX+ GND_D SSRX- SHIELD *0_04 USB3.0 Max Trace length Follow Design Guide ZGND GND1 GND2 C 377AH09FZT S4NVCB P/N = 6-20-B4Z40-109 PCB Footprint = 317AH09FZTS4T4CX ZGND ZGND ZGND ⍾ᘠco-lay, ⚈ᦹlayout⌒᜛ ZD3 CLOSE TO CONNECTOR ZUSB_PN4 ZL1 ZUSB_PP4 *W CM2012F2S-161T03-short ZD4 ZUSB_PN4_CON ZUSB_PP4_CON ZGND 10 ZUSB_PN4_J ZUSB_PP4_J ZTXP4 ZTXN4 ZGND ZRXP4 ZRXN4 ZGND PUSB3F96 10 ZTXP4_J ZTXN4_J ZGND ZRXP4_J ZRXN4_J PUSB3F96 LAN BOARD ZH2 *H5_0D2_5 (⏓USB3.0x2, PHONE JACK, SIM) ZH1 *H7_0D2_3 ZH3 *H8_0D2_8 ZH4 *H7_0D2_3 ZJ_MB1 Z5V B ZC1 ZVDD3 ZC5 10u_6.3V_X5R_06 0.1u_16V_Y5V_04 ZC2 ZGND ZGND 0.1u_16V_Y5V_04 ZGND Z3.3V Z3.3VS ZC3 ZC4 0.1u_16V_Y5V_04 0.1u_16V_Y5V_04 ZGND ZVDD3 Z3.3V ZGND A Z3.3VS 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 ZUSB_PN4 ZUSB_PP4 B ZUSB3_TXN4 ZUSB3_TXP4 ZUSB3_RXN4 ZUSB3_RXP4 ZGND ZUSB_PN3 ZUSB_PP3 ZH6 *H7_0D2_3 76 76 ZUSB3_TXN3 ZUSB3_TXP3 ZUSB3_RXN3 ZUSB3_RXP3 ZCLK_PCIE_GLAN# 74 ZCLK_PCIE_GLAN 74 ZPCIE_TXN5_GLAN ZPCIE_TXP5_GLAN ZPCIE_RXN5_GLAN ZPCIE_RXP5_GLAN B - 76 P670RE USB Board 2/3 ZH5 *H5_0D2_5 ZGND ZGND ZGND 74 74 74 74 D02 ZLAN_CLKREQ# 74 ZPCIE_W AKE# 74 ZLAN_W AKEUP# 74 ZBUF_PLT_RST# 74 ZDD_ON# 75,76 Z5V ZT7 ZT8 ZT9 ZT10 76 A ZVDD3 74 Z3.3V 74,76 Z3.3VS 74 ZT1 ZT6 ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ P67RE USB D02 Title ZT11 Size A3 P67 USB D03 ᾖෑLIBӒҐ ZH7 *H7_0D2_3 76 76 76 76 51049-08041-001 ZGND PCB Footprint = 51049-0804X ZGND ZGND Date: [75] P670RE USB BOARD 2/3 Document Number P650RE Rev D02A 6-71-P67R3-D02A Monday, July 06, 2015 Sheet 75 of 79 Schematic Diagrams P670RE USB Board 3/3 USB3.0 PORT3 (MB⎛ᶳ) USB3.0 re-driver Z3.3V ZUSBVCC3.0_2 ZR62 ZR73 ZR81 *0_04 ZU1 Z5V *4.7K_04 *4.7K_04 ZC18 10u_6.3V_X5R_06 D ZR90 VIN VOUT GND 2K_1%_04 75 ZDD_ON# ZGND ZR17 *0402_short EN# OC# 100 mil ZC17 ZC16 0.1u_16V_Y5V_04 *0.1u_16V_Y5V_04 uP7549UMA5-20 PCB Footprint = M-SOT23-5 TX2VCC RX2+ TX2+ Z_SCK_P3 ZC75 0.1u_10V_X7R_04 ZUSB3_TXN3 75 ZC76 0.1u_10V_X7R_04 ZUSB3_TXP3 75 10 *4.7K_04 ZGND ZUSBVCC3.0_2 22u_6.3V_X5R_08 ZC9 22u_6.3V_X5R_08 11 ZC77 0.1u_10V_X7R_04 ZUSB3_RXN3 75 12 ZC74 0.1u_10V_X7R_04 ZUSB3_RXP3 75 ZTXP3_J ⚈⍾ᘠco-lay, ⎴ᏽ⍾ᘠᢃё ZTXN3_J ZUSB_PN3_J ZUSB_PP3_J ZRXP3_J Z3.3V Z3.3V ZRXN3_J SSTX+ SHIELD VBUS SSTXDGND D+ SSRX+ GND_D SSRX- SHIELD C ZR84 ZR55 *0_04 ZR83 ZR76 ZR64 *4.7K_04 *4.7K_04 *4.7K_04 ZC62 ZC73 0.1u_10V_X7R_04 GND1 GND2 C 377AH09FZT S4NVCB ZGND P/N = 6-20-B4Z40-109 PCB Footprint = 317AH09FZTS4T4CX ZC69 ZGND 0.01u_16V_X7R_04 ZGND ZJ_USB3_1 From PCH ZGND ASM1464 PCB Footprint = QFN24-4X4MM ZC11 Standard-A GND DE_A SW_A EN_RXD VCC RX2- 13 19 CHIP_EN# Reserverd 20 ZC61 TYPE_IND# SW_B ZC60 0.1u_10V_X7R_04 RX1RX+ DE_B 0.1u_10V_X7R_04 ZRXP3 SMB_SCK TX1+ 18 ZRXN3 TX1- 14 21 To Conn GND SMB_DATA 15 22 EQ_B 23 ZC59 GND ZC58 0.1u_10V_X7R_04 16 0.1u_10V_X7R_04 ZTXP3 17 Z_SDA_P3 ZTXN3 ZGND ZR97 Sheet 76 of 79 P670RE USB Board 3/3 1u_6.3V_X5R_04 *0_04 USB3.0 Max Trace length Follow Design Guide ZGND ZGND ZD1 ⍾ᘠco-lay, ⚈ᦹlayout⌒᜛ 75 ZUSB_PN3 75 ZUSB_PP3 ZL2 *W CM2012F2S-161T03-short ZUSB_PN3_CON ZUSB_PP3_CON ZGND 10 ZUSB_PN3_J ZUSB_PP3_J ZGND PUSB3F96 ZD2 10 ZTXP3 ZTXN3 ZRXP3 ZRXN3 B ZGND ZTXP3_J ZTXN3_J ZGND ZRXP3_J ZRXN3_J B PUSB3F96 A A Z5V 75 Z3.3V 74,75 Z3.3VS 74,75 ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ Title Size A3 Date: [76] P670RE USB BOARD 3/3 Document Number P650RE Rev D02A 6-71-P67R3-D02A Monday, July 06, 2015 Sheet 76 of 79 P670RE USB Board 3/3 B - 77 B.Schematic Diagrams *4.7K_04 25 24 EQ_A ZU6 ZR46 ZGND 2A/90mohm ZGND ZGND D Schematic Diagrams P670RE LED Board YR30 *330_04 YLED_ACIN YR17 330_04 Oragne YR31 *330_04 YLED_PWR YR16 330_04 YJ_MB NC2 Green YD1_1 UHY YD1_3 UYG D RY-SP195UHYUYG4 AC IN/POWER ON LED Y_GND Y_GND Y_3.3VS YR32 *330_04 YD8 FP225H-012S10M PCB Footprint = fp225-012g Sheet 77 of 79 P670RE LED Board YLED_BAT_CHG YR19 330_04 Oragne YR33 *330_04 YLED_BAT_FULL YR18 330_04 Green YD8_1 UHY YD8_3 UYG RY-SP195UHYUYG4 BAT CHARGE/FULL LED Y_GND C C YR28 YR29 220_04 220_04 220_04 NUM LOCK LED YD2 HDD C RY-SP190YG34-5M YD3 LED RY-SP190YG34-5M AIRPLANE LED dGPU LED YD4 RY-SP190YG34-5M RY-SP190YG34-5M YLED_CAP# YLED_NUM# YSATA_LED# Y_WLAN_AIRPLANE# *0_04 C YR1 YLED_SCROLL# B P670RE LED D01 C YD5 RY-SP190YG34-5M C RY-SP190YG34-5M B CAPS LOCK LED C YD6 LED C SCROLL YD7 LOCK A YR27 220_04 A YR26 220_04 A YR25 220_04 A YR24 A A Y_3.3VS C B Y_dGPU_LED YQ1 DTC114EUA E B.Schematic Diagrams YD1 YLED_ACIN YLED_PWR YLED_BAT_CHG YLED_BAT_FULL YLED_NUM# YLED_CAP# YLED_SCROLL# Y_WLAN_AIRPLANE# Y_dGPU_LED YSATA_LED# 12 11 10 NC1 D Y_GND YH8 *H3_2D2_2 A 1YR *0_04 4YR *0_04 2YR *0_04 5YR *0_04 3YR *0_04 6YR *0_04 YH7 *H3_2D2_2 YH6 *H6_3D2_3 YH5 *H6_3D2_3 ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ Y_GND Y_GND Y_GND Y_GND Title Size A4 Date: B - 78 P670RE LED Board A [77] P670RE LED BOARD Document Number P650RE Rev D01 6-71-P67R4-D01 Friday, July 03, 2015 Sheet 77 of 79 Schematic Diagrams P655RE Power Board I3.3VS IJ_BTN1 D IM_BTN# D NC1 NC2 FP226H-004S10M PCB Footprint = fp226h-004xxxm_r I3.3VS POWER BUTTON POWER SWITCH LED I_SW1 TJE-532-Q-T/R IM_BTN# *0_04 4IR *0_04 2IR *0_04 5IR *0_04 3IR *0_04 6IR *0_04 20mil IR1 C C Sheet 78 of 79 P655RE Power Board 1K_04 PCB Footprint = tje-53x-q 1IR ID2 20mil IC2 IGND 0.1u_50V_Y5V_06 20mil IC1 *V15AVLC0402 *0.1u_16V_Y5V_04 BSW1 IGND ID1 6-53-3050B-B41 100g C P2808A1, ࿄ဳྛᩪᑘ, P2808A1 ҥ⏮ D26 mounted VARISTOR B IGND A VARISTOR 6-24-30003-006 BLUE RE2*0.8 2P P/N = RY-SP190DNB84-5/1X PCB Footprint = RY-SP190YG34-5M IH1 *H6_0D2_2 B IH2 *H6_0D2_2 IGND IGND IGND ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ A Title Size A Date: A [78] P655RE POWER BOARD_I Document Number P650RE Friday, July 03, 2015 Rev D01 6-71-P655C-DR1 Sheet of 78 79 P655RE Power Board B - 79 B.Schematic Diagrams IGND P655RE D01 Schematic Diagrams P655RE LED Board OJ_LED1 D NC1 NC2 OD9 OLED_PWR OR9 330_04 A OD11 OR13 330_04 A C D Green RY-SP260UYG24-5M OD10 OLED_ACIN OR7 330_04 A RY-SP260UYG24-5M OD12 LOT3 OLED_BAT_CHG C Amber OR11 330_04 A C Amber RY-SP260USO24-5M O_GND RY-SP260USO24-5M AC IN/POWER ON LED O_3.3VS BAT CHARGE/FULL LED O_GND O_GND 1OR *0_04 4OR *0_04 2OR *0_04 5OR *0_04 3OR *0_04 6OR *0_04 O_3.3VS C C OR1 330_04 330_04 OD3 OD2 RY-SP260UYG24-5M RY-SP260UYG24-5M RY-SP260UYG24-5M dGPU LED SCROLL LOCK LED CAPS LOCK LED NUM LOCK LED AIRPLANE LED HDD LED P655RE LED D02 OR14 *0_04 C OLED_SCROLL# OLED_CAP# OLED_NUM# C OD5 RY-SP260UYG24-5M C OD6 RY-SP260UYG24-5M C OD7 RY-SP260UYG24-5M C OD4 C C A OR2 330_04 A OR4 330_04 A OR5 330_04 A OR6 330_04 A OR3 A Sheet 79 of 79 P655RE LED Board OLED_BAT_FULL C Green FP225H-012S10M PCB Footprint = fp225-012g O_WLAN_AIRPLANE# OSATA_LED# B O_dGPU_LED B E B.Schematic Diagrams OLED_ACIN OLED_PWR OLED_BAT_CHG OLED_BAT_FULL OLED_NUM# OLED_CAP# OLED_SCROLL# O_WLAN_AIRPLANE# O_dGPU_LED OSATA_LED# 12 11 10 B OQ1 DTC114EUA O_GND P655RE LED D02AዷባᾖෑƮ# ᙔ!Ϻ!ႝ!တ!!DMFWP!DP/ A Title Size A4 Date: B - 80 P655RE LED Board A [79] P655RE LED BOARD Document Number P650RE Rev 6-71-P6554-DR2A Wednesday, July 08, 2015 Sheet 79 D02A of 79 BIOS Update Appendix C:Updating the FLASH ROM BIOS To update the FLASH ROM BIOS, you must: • • • • • • • Download the BIOS Go to www.clevo.com.tw and point to E-Services and click E-Channel Use your user ID and password to access the appropriate download area (BIOS), and download the latest BIOS files (the BIOS file will be contained in a batch file that may be run directly once unzipped) for your computer model (see sidebar for important information on BIOS versions) Unzip the downloaded files to a bootable CD/DVD or USB Flash drive Insert a bootable CD/DVD/USB flash drive into the CD/DVD drive/USB port of the computer containing the downloaded files Use a tool such as Winzip or Winrar to unzip all the BIOS files and refresh tools to your bootable CD/DVD/USB flash drive (you may need to create a bootable CD/DVD with the files using a 3rd party software) BIOS Version Make sure you download the latest correct version of the BIOS appropriate for the computer model you are working on You should only download BIOS versions that are V1.01.XX or higher as appropriate for your computer model Note that BIOS versions are not backward compatible and therefore you may not downgrade your BIOS to an older version after upgrading to a later version (e.g if you upgrade a BIOS to ver 1.01.05, you MAY NOT then go back and flash the BIOS to ver 1.01.04) Set the computer to boot from the external drive With the bootable CD/DVD/USB flash drive containing the BIOS files in your CD/DVD drive/USB port, restart the computer and press F2 (in most cases) to enter the BIOS Use the arrow keys to highlight the Boot menu Use the “+” and “-” keys to move boot devices up and down the priority order Make sure that the CD/DVD drive/USB flash drive is set first in the boot priority of the BIOS Press F4 to save any changes you have made and exit the BIOS to restart the computer C - C:BIOS Update Download the BIOS update from the web site Unzip the files onto a bootable CD/DVD/USB Flash Drive Reboot your computer from an external CD/DVD/USB Flash Drive Use the flash tools to update the flash BIOS using the commands indicated below Restart the computer booting from the HDD and press F2 at startup enter the BIOS Load setup defaults from the BIOS and save the default settings and exit the BIOS to restart the computer After rebooting the computer you may restart the computer again and make any required changes to the default BIOS settings  BIOS Update Use the flash tools to update the BIOS Make sure you are not loading any memory management programs such as HIMEM by holding the F8 key as you see the message “EFI Shell” You will then be prompted to give “Y” or “N” responses to the programs being loaded by EFI Shell Choose “N” for any memory management programs You should now see DISK fsX:\> (X is the designated drive number for the CD/DVD drive/USB flash drive) Type the following command: C:BIOS Update fsX:\> Flash.nsh The utility will then proceed to flash the BIOS You should then be prompted to press any key to restart the system or turn the power off, and then on again but make sure you remove the CD/DVD/USB flash drive from the CD/DVD drive/USB port before the computer restarts Restart the computer (booting from the HDD) With the CD/DVD/USB flash drive removed from the CD/DVD drive/USB port the computer should restart from the HDD Press F2 as the computer restarts to enter the BIOS Use the arrow keys to highlight the Exit menu Select Load Setup Defaults (or press F3) and select “Yes” to confirm the selection Press F4 to save any changes you have made and exit the BIOS to restart the computer Your computer is now running normally with the updated BIOS You may now enter the BIOS and make any changes you require to the default settings C-2 ... Preface Notebook Computer P650RE6(- G) / P651RE6( -G) / P650RE3( -G) / P651RE3( -G) Service Manual Preface I Preface Notice The company reserves the right to... Chapter 1: Introduction Overview This manual covers the information you need to service or upgrade the P650RE6(- G) / P651RE6( -G) / P650RE3( -G) / P651RE3( -G) series notebook computer Information... questions about those programs, you should consult those manuals 1.Introduction The P650RE6(- G) / P651RE6( -G) / P650RE3( -G) / P651RE3( -G) series notebook is designed to be upgradeable See Disassembly

Ngày đăng: 22/04/2021, 17:27

TỪ KHÓA LIÊN QUAN

w