MINISTRYOFEDUCATIONANDTRAINING MINISTRYOFNATIONALDEFENCE ACADEMY OF MILITARY SCIENCE AND TECHNOLOGY PHAM VAN CHINH INVESTIGATION OF SIMULATION AND OPTIMIZATION FOR NITROGEN GAS GENERATOR USING PRESSURE SWING ADSORPTION PhD THESIS IN TECHNIQUE Hanoi – 2021 MINISTRYOFEDUCATIONANDTRAINING MINISTRYOFNATIONALDEFENCE ACADEMY OF MILITARY SCIENCE AND TECHNOLOGY PHAM VAN CHINH INVESTIGATION OF SIMULATION AND OPTIMIZATION FOR NITROGEN GAS GENERATOR USING PRESSURE SWING ADSORPTION Specialization: Chemical Engineering Code: 9520301 PhD THESIS IN TECHNIQUE Supervisors: Assoc Prof Dr Vu Dinh Tien Dr Le Quang Tuan Hanoi – 2021 i COMMITMENT I hereby declare that this is my own research The research results presented in the thesis and is completely honest Scientific conclusions have never been published in any other work by any authors, reference data are fully cited th March, 19 , 2021 PhD Candidate Pham Van Chinh ii ACKNOWLEDGEMENTS First of all, I would like to express my sincere gratitude to my supervisors Associate Professor.Dr Vu Dinh Tien and Dr Le Quang Tuan for their enthusiastically guidance and helping me to complete this thesis They sincere cooperation at every stage of my research work, their valuable advice and assistance always guided me to conduct my research smoothly Secondly, I would like to thank Head of Academy of Military Science and Technology, Training Department of Academy of Military Science and Technology, Head of Institute of Chemistry - Materials, Department of Physical Chemistry, Department of Machinery and Equipment for Chemical Industrial, School of Chemical Engineering, Hanoi University of Technology, Head of Institute of Technology/General Department of Defense Industry, Department of Chemical Technology have always enthusiastically guided and helped me in all aspects of the thesis implementation process Finally, I am in debt of my families, friends and relatives for their love and encouragement and motivation in the process of implementing the thesis PhD Candidate Pham Van Chinh iii TABLE OF CONTENTS Page NOMENCLATURE vi LIST OF TABLES xi LIST OF FIGURES .xii INTRODUCTION CHAPTER I - OVERVIEW 1.1 Air composition and separation technichques 1.1.1 Air composition 1.1.2 Air separation techniques 1.2 Absorbent 17 1.2.1 Introduction of adsorption and adsorbent 17 1.2.2 Molecular sieve adsorbent 19 1.3 Theoretical background of adsorption, desorption and nitrogen gas generator using pressure swing adsorption 25 1.3.1 Theoretical background of adsorption and desorption processes 25 1.3.2 Structure of adsorption column 28 1.3.3 Mechanism of adsorption process 29 1.3.4 Structure and principle of N2 gas generator using pressure swing adsorption 31 1.4 Mathematical model, simulation and optimization for a single fixed bed .34 1.4.1 Mathematical models to describe a single fixed bed 34 1.4.2 Simulation for process and equipment in adsorption .38 1.4.3 Optimization of nitrogen gas generator 39 1.5 The results recently 42 1.5.1 In the world 42 1.5.2 In Vietnam 45 CHAPTER II - OBJECTS AND METHODOLOGY 49 2.1 Object and scope 49 2.2 Materials, chemicals and equipment 49 iv 2.2.1 Carbon Molecular Sieve 49 2.2.2 Analytical equipment for investigating characteristics of adsorbent 49 2.2.3 A complete experimental system is N2 gas generator using PSA cycle 50 2.3 Methodology 50 2.3.1 Introduction 50 2.3.2 General method 51 2.3.3 Studying method about carbon molecular sieve 51 2.3.4 Methods of a building experimental systems for air separator by PSA 52 2.3.5 Determining method of diffusion coefficient 54 2.3.6 Determining method of pressure drop through particle layer of a bed 55 2.3.7 Methods establish a mathematical models to describe a single fixed bed 57 2.3.8 Simulation and optimization of air separator 61 2.3.9 Experimental method 63 2.2.10 Method scale-up of industry 64 CHAPTER III - RESULTS AND DISCUSSION 65 3.1 Specifications of CMS-240 65 3.1.1 Some general specifications of CMS-240 65 3.1.2 Thermal analysis DSC and TG of CMS-240 66 3.1.3 Composition and structure of CMS-240 67 3.1.4 Specific surface of CMS-240 71 3.2 Manufacturing an experimental system to separate nitrogen gas from air .74 3.2.1 Calculation characteristics and basic dimensions of a single fixed bed 74 3.2.2 Maximum adsorption capacity calculation of a single fixed bed 75 3.2.3 Manufacturing an experimental system to generate nitrogen gas 77 3.3 Calculation, measure and analyze pressure drop of particle layer 83 3.3.1 Pressurization 84 3.3.2 Adsorption 84 3.3.3 Descrease pressure 85 3.3.4 Desorption 85 3.4 Mathematical models describe a single fixed bed by partial pressure .89 v 3.5 Determine velocity and diffusion coefficient 90 3.5.1 Velocity of air flow through a single fixed bed, uc (m/s) 91 3.5.2 Molecular diffusion coefficient, DAB (cm /s) 91 3.5.3 Determination membrane diffusion coefficient (Knudsen), Dk (cm /s) .92 3.5.4 Axial diffusion coefficient, DL (cm /s) 92 3.6 Summary parameters of nitrogen gas generator 95 3.7 Simulation and optimization for nitrogen gas generator 97 3.7.1 Simulation and optimization for a single fixed bed 97 3.7.2 Investigation of simulation and optimization for N2 gas generator using PSA 122 3.7.3 Simulation and experimental comparision of a single fixed bed and two beds 145 3.8 Scale-up industry for equipment and applications 147 3.8.1 Scale-up industry for equipment with different productivity 148 3.8.2 Application of N2 gas generators for production of RDX explosive 152 CONCLUSSIONS .157 THE SCIENTIFIC PUBLICATIONS 161 REFERENCES 163 vi NOMENCLATURE ai,1 Coefficient a1 isothermal bi-Langmuir of component i ai,2 Coefficient a2 isothermal bi-Langmuir of component i bi,1 bi,2 DL Dia F Coefficient b1 isothermal bi-Langmuir of component i Coefficient b2 isothermal bi-Langmuir of component i Axial diffusion coefficient (adsorption bed) Diameter of bed Feed raw materials into bed IP1 Isothermal constant in Aspen Adsorption IP2 Isothermal constant in Aspen Adsorption ki Mass transfer coefficient of component i Ki Equilibrium constant of the component i L, H Height of bed Z Axial distance across bed (from top to bottom of bed) ΔP Pressure drop ΔPi Partial pressure drop of component i Pe Standard number Peclet of adsorbent particles qi * q i rp S Vbed U Amount of gas absorbed in adsorbent of component i Amount of gas absorbed in adsorbent of component i in equilibrium Particle radius Cross-sectional area of bed Volume of bed Theoretical velocity of air flow vii V D j Volume of dead zone in bed [cm ] XFac Volume correction factor [-] ΔPj Pressure drop in partial j [bar] ΔPmax Maximum pressure drop through bed [bar] VT Total empty column volume Vx Empty volume between particles Vp Empty volume inside particles εi Intergranular porosity (internal porosity) εp Porosity inside particles (particle porosity) εt Internal and intergranular porosity (total porosity) m void m m void m void m void m void µ ψ Viscosity of liquids, gases m void Coefficient of particle shape ϕ Pressure drop coefficient [cP]3 P V T Pressure of gas Volume of gas bar.min Absolute temperature of gas [mmHg, kG/cm ] Rk Constant of dry air cm2 [m ] [K] Rhn Constants of water vapor Ci t [-] Concentration of component i in gas mixture Time 2,153 [mmHg.m /k g.K] 3,461 [mmHg.m /k g.K] [mol/cm ] [s] 157 CONCLUSSIONS * The main results of the thesis The thesis has identified basic characteristics of carbon molecular sieve adsorbent CMS-240 what supplier does not provide such as bulk density, particle density, solid density, particle size distribution, porosity, specific surface, composition and structure of adsorbent by analysis and calculation methods available in Vietnam The results show that the main component of the adsorbent is carbon, cylindrical particles, two-layer structure They are fabricated by impregnation, extrution and drum coating and activation at very high velocity and strictly controlled conditions There are a lot of macropores, mesopores and micropore uniformly, total porosity of the adsorbent is ε t = 0.615, specific surface result is determined by calculation according to capacity of bed S r = 1146 m /g is quite reliable compared to the actual yield obtained; to has built a completely experimental system of N2 gas generator successfully as pilot scale, with high level of automation to study purposes, It has productivity from 10 L/min to 14 L/min N gas ≥ 99.5% at standard conditions It is installed a full range of measuring insttruments (pressure, temperature, flow and concentration sensors) with high accuracy (pressure sensors are installed according to height of bed, mass flow I/O flow sensor and S7-1200 PLC control system, real-time accurate data acquisition monitoring and monitoring (SCADA) can import and export data easy experiments; to calculated, analyzed and measured of pressure drop through particle layer of bed, depending on velocity of gas flow through section of bed and diffusion process in the adsorption and desorption processes In fact, the pressure drop through particle layer is not linearly dependent on velocity in the adsorption and desorption processes due to pore attraction The thesis has established a mathematical model describing rules of adsorption and desorption processes in a single fixed bed according to partial pressure of oxygen depending on time and height of bed with initial condition and boundary conditions as working mode of bed and equipment according to pressure 158 swing adsorption (PSA); to have calculated to determine a set of model parameters to program and simulate the established mathematical model; to has determined the important model parameters by calculation such as the parameters of materials, bed and equipment, equilibrium constants and especially velocity and diffusion coefficient; contemporaneous, to chose a hidden back OLE algorithm to program and simulate a single fixed bed and equipment using Matlab software Sequently, to used Presto software to simulate movement through bed and Aspen Adsorption software to optimize the simulation to achieve the highest productivity, stable product concentration; to studied the rules of changes in technological parameters of pressure, flow and concentration, especially pressure drop and factors affecting productivity and purity product Study on the factors affecting the adsorption process, optimize a single fixed bed to optimize for N gas generator on a experimental system that has achieved N purity ≥ 99.5% stable with the highest product recovery The mathematical model and simulation results are compatible with the built experimental system, with acceptable errors The thesis has studied industrial scale-up this equipment successfully by calculating and simulating on softwares at different productivity for specific applications in manufacturing and storage Contemporaneous, the thesis has built a complete method by simulating and optimizing for air separators by molecular sieve adsorbent using the adsorption cycles * New contributions of the thesis The thesis has clarified the rule of pressure change in a single fixed bed and N2 gas generator according to the height of bed and time in a working cycle by a mathematical model is described by partial pressure of O2 (component is adsorbed), which is simulated by commercial and self-contained softwares successfully for N2 gas generator is a small capacity (pi-lot) Having studied industry scaled-up for specific applications at suitable capacity successfully, that is achieving good results by calculation combined with simulation of separating technique by adsorption using pressure swing adsorption cycle and carbon molecular sieving adsorption material completely 159 In addition, the thesis has built a systematic approach to simulate, optimize and scale-up of separator using molecular sieve adsorbents and the pressure swing adsorption cycle: from studying characteristics and structure of carbon molecular sieve adsorbents, calculating, design of a single fixed bed or equipment and calculation and analysis of pressure drop, velocity and diffusion coefficient for simulation and optimization of nitrogen gas generator by math model and software This method can be applied to study other separative processes and equipments using molecular sieve adsorbents and adsorption cycles * Further directions Results of the thesis, which shows that investigation of simulation and optimization for separative equipments to separate gase components from its mixture using PSA cycle and molecular sieve adsorption materials Nowaday, this issue is very attractive in terms of science as well as practice and application in practice These research results and methods have great potential for applications in chemical and petrol refinery industries, especially in substance separation techniques Because this method can give results quickly, accuratetly and effectively Some directions can be deployed to solve necessary science and fact problems in as follows, for example: - Investigate on simulating of temperature during adsorption and desorption processes in a single fixed bed of N2 gas generator using pressure swing adsorption - Study on improving product purity and capacity of N gas generators using pressure swing adsorption by heterogeneous reaction technique to reduce O by H2 gas after nitrogen gas generator - Investigation of simulation and optimization for O gas generator using pressure swing adsorption and zeolite 5A, 13X molecular sieve adsorbent to medical, supporting treatment for patients with Covid-19 in Vietnam - Investigation of simulation and optimization for separation processes by PSA, VSA, TSA to separate CO 2, H2, C2H5OH gases for fuel preparation, gas processing and other industrial components 160 - Investigation of simulation and optimization for absolute alcohol production equipment by zeolite 3A using pressure swing adsorption Because, simulation is a best method for deploying processes and equipment of chemical engineering This method can give shorten time and high economic efficiency Separation technique using the adsorption cycle and molecular sieve adsorbent is a potential field in the future In addition, this method can be used to simulate and optimize the existing production line and other dissociation processes by Aspen Plus software 161 THE SCIENTIFIC PUBLICATIONS Pham Van Chinh, Nguyen Tuan Hieu, Le Quang Tuan, Vu Dinh Tien (2018) Assembling of an experimental system to investigate and optimize of nitrogen gas generator using pressure swing adsorption to separate nitrogen gas from the air Journal of Military Science and Technology (ISSN 1859-1043), no 56, p 157-165 Pham Van Chinh, Nguyen Tuan Hieu, Le Quang Tuan, Vu Dinh Tien (2018) Design a measuring and control system to investigate and optimize of nitrogen gas generator using pressure swing adsorption Journal of Military Science and Technology (ISSN 1859-1043), special issue 08, p 269-275 Pham Van Chinh, Nguyen Tuan Hieu, Le Quang Tuan, Vu Dinh Tien (2019) Investigation of Simulation and optimization for nitrogen gas generator using pressure swing adsorption (PSA) by Aspen Adsorption Software Journal of Military Science and Technology (ISSN 1859-1043), no.61, p.140-149 Pham Van Chinh, Nguyen Tuan Hieu, Le Quang Tuan, Vu Dinh Tien (2019) Study comparative and selection of 4-step and 6-step using pressure swing adsorption to generate N2 gas Journal of Catalytic and Adsorption Viet Nam (ISSN 0866-7411), Volume 8, Issue 3, p25-31 Pham Van Chinh, Nguyen Tuan Hieu, Le Quang Tuan, Vu Dinh Tien (2019) Study on the carbon molecular sieve adsorbent CMS-240 used in the N gas generator Journal of Military Science and Technology (ISSN 1859-1043), no.62, p97-105 Pham Van Chinh, Nguyen Tuan Hieu, Nguyen Tan Y, Nguyen Hoang Nam, Do Van Thom, Ngo Thi Anh, Vu Dinh Tien (2019) Simulation and experiment study of a single fixed bed model of nitrogen gas generator working by pressure swing adsorption Special Issue “Chemical Process Design, Simulation and Optimization” of Journal Processes (ISSN 2227-9717) Processes 2019, (10), 654; https://doi.org/103390/pr7100654 Pham Van Chinh, Nguyen Tuan Hieu, Le Quang Tuan, Vu Dinh Tien (2019) Establish a mathematical model to describe pressure swing adsorption in N gas 162 generator Journal of Military Science and Technology (ISSN 1859-1043), special issue FEE – October, p357-364 Pham Van Chinh, Nguyen Tuan Hieu, Le Quang Tuan, Vu Dinh Tien (2019) Study on simulation about partial pressure of oxygen in a single fixed bed of nitrogen gas generator using pressure swing adsorption Journal of Military Science and Technology (ISSN 1859-1043), no.64 – December, p132-139 Pham Van Chinh, Nguyen Tuan Hieu, Le Quang Tuan, Vu Dinh Tien (2019) Study on caculation and simulation of pressure drop through a single fixed bed of nitrogen gas generator using pressure swing adsorption CASEAN-6 Proceedings (ISBN 978-604-913-088-5), p60-66 10 Pham Van Chinh, Nguyen Tuan Hieu, Le Quang Tuan, Vu Dinh Tien (2020) Study on calculating the kinetic parameters of the mathematical model describing the adsorption process of a single fixed bed of N gas generator using pressure swing adsorption (PSA) and carbon molecule sieve adsorbent CMS-240 Journal of Catalytic and Adsorption Viet Nam (ISSN 0866-7411), Volume 9, Issue 1, p1-7 163 REFERENCES Vietnamese Võ Văn Bang, Vũ Bá Minh (2004) Quá trình thiết bị Cơng nghệ Hóa học & Thực phẩm – Tập 3, Truyền khối Nhà xuất Đại học Quốc gia – TP 10 11 12 13 14 Hồ Chí Minh Nguyễn Bin (2008) Các q trình, thiết bị cơng nghiệp hóa chất thực phẩm, Tập 4: Chưng luyện, hấp thụ, hấp phụ, trích ly, sấy Nhà xuất Khoa học Kỹ thuật Lê Văn Cát (2002) Hấp phụ trao đổi ion trong kỹ thuật xử lý nước & nước thải Nhà xuất Thống kê Trần Đức Cường (1976) Giáo trình Quá trình thiết bị chuyển khối Nhà xuất Đại học Bách khoa Hà nội Đặng Vũ Chí, Hồng Kiều Hưng (2013) Nghiên cứu giải pháp bơm xả khí ni tơ trình khai thác nhằm phịng chống cháy mỏ vỉa 24 khu Tràng Khê Công ty TNHH MTV than Hồng Thái Tạp chí KHKT mỏ địa chất, số 43, p 51-55 Võ Chí Chính (2003) Tính tốn thiết kế Hệ thống điều hịa khơng khí Nhà xuất Đà Nẵng Cao Vân Điểm, Nguyên Xuân Trang (2006) Nghiên cứu thiết kế chế tạo máy làm giàu oxy dùng y tế L/ph Bộ KHCN - YT, Hà Nội Tạ Ngọc Đôn (2012) Rây phân tử vật liệu hấp phụ Nhà xuất Đại học Bách Khoa Hà Nội Hà Văn Hảo, Vũ Đình Tiến (2015) Mơ q trình làm việc thiết bị tạo khí ni tơ chu trình hấp phụ thay đổi áp suất Tạp chí Xúc tác Hấp phụ, số 3, p 165-169 Nguyễn Minh Hệ, Nguyễn Đức Trung, Phan Minh Thụy (2018) Cơ sở đo lường lý thuyết điều khiển tự động q trình cơng nghệ Nhà xuất Đại học Bách khoa Hà nội Nguyễn Thị Minh Hiền (2014) Mô q trình Cơng nghệ hóa học Nhà xuất Đại học Bách khoa Hà nội Mai Xuân Kỳ (2006) Thiết bị phản ứng Công nghiệp hóa học, Tập 1,2 Nhà xuất Khoa học Kỹ thuật Trần Cơng Minh (2007) Khí hậu khí tượng đại cương Nhà xuất Đại học Quốc gia Hà nội Nguyễn Hữu Phú (1998) Hấp phụ Xúc tác bề mặt vật liệu vô mao quản Nhà xuất Khoa học Kỹ thuật 164 15 Hồ Hữu Phương (1977) Cơ sở tính tốn thiết bị hóa chất Nhà xuất Đại 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 học Bách Khoa Hà nội Hồ Viết Q (2007) Các phương pháp phân tích cơng cụ hóa học đại Nhà xuất Đại học Sư phạm - Hà nội Bùi Văn Tài (2018) Nghiên cứu số yếu tố ảnh hưởng trình chế tạo than hoạt tính dạng vải sợi từ nguyên liệu sợi viscose Luận án Tiến sĩ Hóa học – Viện Khoa học Công nghệ quân Phan Thanh Tao (2004) Giáo trình Matlab Nhà xuất Đại học Bách Khoa – Đại học Đà Nẵng Vũ Đình Tiến (2017) Giáo trình Hấp phụ Trao đổi ion Nhà xuất Đại học Bách khoa Hà Nội Nguyễn Văn Thắng (2016) Giáo trình Vật lý Khí Nhà xuất Tài Nguyên – Môi trường Bản đồ Việt Nam Nguyễn Đình Thành (2011) Cơ sở phương pháp phổ ứng dụng hóa học Nhà xuất Khoa học Kỹ thuật Hồ Sĩ Thoảng (2006) Giáo trình Xúc tác dị thể Nhà xuất Viện Khoa học Công nghệ Việt Nam Bùi Trung Thành, Nguyễn Hay (2009) Xác định vận tốc khí qua lớp hạt sơi tối thiểu mơ hình máy sấy muối tinh tầng sơi liên tục Tạp chí Cơ khí Việt Nam, số 148, p19-24 Nguyễn Hoa Toàn, Lê Thị Mai Hương (2005) Công nghệ hợp chất vô ni tơ Nhà xuất Khoa học Kỹ thuật Đinh Trọng Toan, Nguyễn Trọng Khng (1999) Sổ tay q trình thiết bị cơng nghệ hóa chất - Tập 1,2 Nhà xuất Khoa học kỹ thuật Phạm Anh Tuấn, Vũ Thị Nga (2016) Tối ưu hóa số thơng số công nghệ bảo quản long kỹ thuật bao gói khí điều biến Tạp chí Khoa học Công nghệ, số 54(4A), p314-322 Nguyễn Hữu Tùng, Trần Trung Kiên (2016) Hóa cơng – Cơ sở chuyển khối Nhà xuất Đại học Bách khoa Hà nội Nguyễn Hữu Tùng (2012) Kỹ thuật tách hỗn hợp nhiều cấu tử Tập 1,2 Nhà xuất Đại học Bách khoa Hà nội Nguyễn Minh Tuyển, Phạm Văn Thiêm (2018) Kỹ thuật hệ thống Cơng nghệ Hóa học, Tập 1, Cơ sở mơ hình hóa q trình cơng nghệ hóa học Nhà xuất Đại học Bách Khoa Hà Nội Lê Trọng Vinh, Trần Minh Tồn (2019) Giáo trình Phương pháp tính Matlab Nhà xuất Đại học Bách khoa Hà nội Quy chuẩn kỹ thuật Quốc gia QCVN 06:2011/BTC (2011) dự trữ nhà nước gạo Bộ Tài ban hành 165 32 Tiêu chuẩn quốc gia TCVN 3286:1979 (1979) Tiêu chuẩn phương pháp thử nitơ kỹ thuật 33 Công ty TNHH Vạn Tấn Phát (2017) Nitơ hướng dẫn sử dụng sản phẩm (MSDS) English 34 A.R.Smith, J.Klosek (2001) A review of air separation technologies and their integration with energy conversion processes Fuel Processing Technoloy, no 70, pp 115-134 35 A Da˛browski (2001) Adsorption - from theory to practice Advances in Colloid and Interface Science, Vol.93, p135-224 36 Anders Rasmuson, Ronnie Andersson (2014) Mathematical Modeling in Chemical Engineering Cambridge University Press 37 Ashkan, Mostamand, Masoud, Mofarahi (2011) Simulation of a Single Bed Pressure Swing Adsorption for Producing Nitrogen International Conference on Chemical, Biological and Environment Sciences, Bangkok 38 Adamus, A.(2002) Review of the use of nitrogen in phes fires The Institue of Materials, Pherals and Phing, no 111, pp A89-A98 39 Alda Lumban Gaol, Djoko Setyanto (2018) Optimization of Nitrogen Air Separation Plant with Experimental Method International Journal of Applied Engineering Research, Volume 13, Number 13 (2018) pp 1125211260 40 A Marcinek, J Guderian, D Bathen (2020), Performance determination of high-purity N2-PSA-plants Adsorption volume 26, pages1215–1226(2020), ISSN:1572-8757, FH Münster-University of Applied Sciences, https://doi.org/10.1007/s10450-020-00204-9 41 Bahram Haddadi, Christian Jordan (2016) Investigation of the Pressure Drop of Random Packed Bed Adsorbers Chemical Engineering Transactions, Vol.52 (p439-444), Copyright © 2016, AIDIC Servizi S.r.l 42 C B&echaud, S M&elen, D Lasseux; ∗, M Quintar, C H Bruneau (2001) Stabilityanaly sis of a pressure swing adsorption process Chemical Engineering Science 56 (2001) 3123–3137 43 C.L Cavalcante JR (2000) Industrial Adsorption separation proceses: fundamentals, modeling and applications Latin American Applied Research 30:357-364 44 C.Barg, J.M.P.Ferreira (2000) Simulation and Optimization of an industrial PSA unit Brazilian Journal of Chemical Engineering, vol.17 n.4-7 166 45 Choi Y, Kim S, Kim D (2008) A Semi-empirical Correlation for Pressure Drop in Packed Beds of Spherical Particles Transp in Porous Med; Vol.75(2): p133-49 46 Christie J.Geankoplis (1993) Transport Processes and Unit Operations – Third Edition Prentice-Hall International Inc 47 David R Vinson (2006) Air separation control technology Computers and Chemical Engineering 30 (2006) 1436–1446 48 Douglas M Ruthven, Shamsuzzanman Farroq, Kent S Knaebel (1994) Pressure Swing Adsorption New York: Wiley - VCH Publishers 49 D.Roy Chowdhury, S.C Sakar (2016) Application of Pressure Swing Adsorption Cycle in the quest of production of Oxygen and Nitrogen International Journal of Engineering Science and Innovative Technology, Vol 5, no 2, pp 64-69 50 Dr Hussein, H Hamed (2015) Oxygen Separation from Air Using Zeolite Type 5A International Journal of Scientific and Engineering Research, vol 6, no 5, pp 597-602 51 Dr M Wulkow (2000), Presto Manual, Simulation of Kinetic Models Computing in Technology GmbH Oldenburger Straße 200, 26 180 Rastede 52 Engineers, Department of the Army US Army Corps of (2001) Engineering and Design Adsorption Design Guide, US 53 Daniel Bahamon Garcia (2015), New generation adsorbents for gas separation:from modelling to industrial application A dissertation submitted in partial fulfillment of the requirements for the degree of doctor of philosophy, Universitat Autonama de Barcelona 54 E J Shokrooi, S M A M Motlaghian (2015) A robust and user friendly sofware (TB-PSA-SS) for numerical sumulation of two – bed pressure swing adsorption proceses Petroleum & Coal Vol.57(1):p13-18 55 Evgeny Akulinin, Stanislav Dvoretsky (2020), Optimization and Analysis of Pressure Swing Adsorption pressure process for oxygen production from air under uncertaintly Chemical Industry & Chemical Engineering Quarterly Q 26 (1) 89−104, https://doi.org/10.2298/CICEQ190414028A 56 Gerhard Wurm, Georgi Paraskov (2004) On the importance of gas flow through porous bodies for the formation of planetesimals The Astrophysical Journal, Vol.606: p983–987 57 Grande, Carlos A (2012) Advances in Pressure Swing Adsorption for Gas Separation International Scholarly Research Network ISRN Chemical Engineering, vol 2012, p 13 page 167 58 Hans-Jorg Bart, Ulrich Von Gemmigen (2012) Adsorption (Ullmann’s Encyclopedia of Industrial Chemistry) Wiley – VCH Verlag GmbH &KgaA, Weinhein, Vol.1, p549-620 59 Heinz-Wolfgang Häring (2008) Industrial Gases Processing WILEY-VCH Verlag GmbH & Co KGaA, Weinheim 60 H G Karge • J.Weitkamp (2008) Molecular Sieves: Science and Technology Springer-Verlag Berlin Heidelberg 61 Harish Khajuria (2011), Model-based Design, Operation and Control of Pressure Swing Adsorption Systems A thesis submitted to Imperial College London for the degree of Doctor of Philosophy, Center for Process System Engineering, Department of Chemical Engineering, Imperial College London, United Kingdom 62 Iman Ahmadi Kakavandi IA, Shokroo EJ, Baghbani M, Farniaei M (2017) Dynamic Modeling of Nitrogen Adsorption on Zeolite 13X Bed Fluid Mechanic Research International, Vol.1(1), p1-6 63 J.D Seader, Ernest J Heney, D Keith Roper (2011) Separation Process Principles Chemical and Biochemical Operations John Wiley and Sons, Inc 64 Juma Haydary (2019) Chemical Process Design and Simulation: Aspen Plus and Aspen HYSYS Applications JohnWiley & Sons, Inc 65 Jaime Benitez (2009), Principles and modern applications of mass transfer operations (Second Edition) John Wiley & Sons, Inc 66 Javadi Shokroo Ehsan, Mofara Masoud (2014) Pilot-Scale Experiments for Nitrogen Separation from Air by Pressure Swing Adsorption South African Journal of Chemical Engineering, vol 19, no 2, pp 42-56 67 Jafar Sadeghzadeh Ahari, Saeed Pakseresht (2008) Deterphation effects of Process Variable on Nitrogen Production PSA System by Mathematical Modeling Petroleum and Coal, vol 2, no 50, pp 52-59 68 J C Santos, A F Portugal, F D Magalha˜es, and A Mendes (2006) Optimization of Medical PSA Units for Oxygen Production Ind Eng Chem Res 2006, 45, 1085-1096 69 Jeong-Geun Jee, Sang-Jin Lee and Chang-Ha Lee (2004) Comparison of the Adsorption Dynamics of Air on Zeolite 5A and Cacbon Molecular Sieve Beds Korean Journal Chemical Engineering, Vol 21(6), p1183-1192 70 J.L.Soares; H.J.José; R.F.P.M.Moreira (2003) Preparation of a cacbon molecular sieve and application to separation of N 2, O2 and CO2 in a fixed bed Brazilian Journal of Chemical Engineering, Vol.20, no.1 71 Juan M Rodriguez, Tommy Edeskär (2013) Particle Shape Quantities and Measurement Techniques–A Review Electronic Journal Geotechnical Engineering, Vol.18: p169-198 168 72 Jamie Trahan, Alessandro Graziani (2013) Evaluation of pressure drop and 73 74 75 76 77 78 79 80 81 82 83 84 85 particle sphericity for an air-rock bed thermal energy storage system Energy Procedia, Vol.57: p 633 – 642 Kamal I.M, Al-Malah (2017) ASPEN PLUS® Chemical Engineering Applications John Wiley & Sons, Inc Kamal I.M Al-Malah (2017) Aspen Plus®:Chemical Engineering Applications, First Edition John Wiley & Sons, Inc Kevin R.Wood, Y.A.Liu, Yueying Yu (2018) Design, Simulation and Optimization of Adsorption and Chromatographic Separation: A Hand-On Approach, First Edition Wiley-VCH Verlag GmbH and Co.KgaA Kulkarami, Sunil Jayant (2016) Pressure Swing Adsorption: A Summary on Investigation in Recent Past International Journal of Research and Review, vol 3, no 10, pp 46-49 K.C.Chong, S.O.Lai, H.S.Thiam, H.C.Teoh, S.L.Heng (2016) Recent progress of oxygen/nitrogen separation using membrane technology Journal of Engineering Science and Technology, vol 11, no 7, pp 1016-1030 Li L, Ma W (2011) Experimental study on the effective particle diameter of a Packed Bed with Non-Sperical Particles Transp in Porous Med; Vol.89:p35-48 Mohammed Salique, Nabila Rumane, (2016) Oxygen Concentrators - A Study International Journal of Scientific Research and Modern Education, vol I, no I, pp 205-210 M.Delavar, N.Nabian (2015) An investigation on the Oxygen and Nitrogen separation from air using cacbonaceous adsorbents Journal of Engineering Science and Technology, vol 10, no 11, pp 1394-1403 M Vaduva, V Stanciu (2007) Cacbon molecular sieves production and performance assessment in cacbon dioxide separation Journal of optoelectronics and advanced materials, Vol.9, No.7, p.2296 – 2301 Mădălina Vaduva and Vasile Stanciu (2008) Separation of nitrogen from air Revue Roumaine de Chimie, Vol.53(3), p223–228 M.H Chahbani,D.Tondeur (2001) Pressure drop in fixed-bed adsorbers Chemical Engineering Journal 81, p 23–34 M.h.Macconell (2005), Instrument Engineers’ Handbook, Process Control Optimization (Separation Controls, Air p2123-2136) Taylor&Francis Group LLC Masoud Mofarahi, Ehsan Javadi Shokroo (2013) Comparison of two pressure swing adsorption proceses for air separation using zeolite 5A and zeolite 13X Petroleum & Coal Vol.55 (3) p216-225 169 86 Maedeh Mohammadi, Ghasem D Najafpour (2011) Production of cacbon molecular sieves from palm shell through cacbon deposition from methane Chemical Industry & Chemical Engineering Quarterly Vol.17 (4) p525−533 87 Mădălina Vaduva, V Stanciu (2006) Separation of nitrogen from air by selective adsorption of cacbon molecular sieves U.P.B Sci Bull., Series A, Vol 68, No 2, p71-86 88 Matthias Bitzer (2005) Model–based Nonlinear Tracking Control of Pressure Swing Adsorption Plants Control and Observer Design, LNCIS 322, pp 403–418 89 Phgfei Pan, Hecham M Omar and Sohrab Rohani (2017) Application of Nanosize Zeolite Molecular Sieves for Medical Oxygen Concentration Nanomaterials, Vol 7, 195 90 Nisith Kr Das, Pradeep Kumar (2010) Multi-component Adsorption Studies on LiLSX and CMS for Helium Separation Adsorption Science & Technology Vol 28 No 3, p281-296 91 Nguyen Hong Khanh, Nguyen Viet Hoang (2006) Adsorption process on fixed bed column in rich organic wastewater treatment experimental studies and numerical simulation Vietnam Journal of Mechanics, VAST, Vol 28, No (2006), pp 28 – 34 92 P Pruksathorn, T.Vitidsant (2009) Production of Pure Ethanol from Azeotropic Solution by Pressure Swing Adsorption American Journal of Engineering and Applied Sciences, vol 2, no 1, pp 1-7 93 Pranta Sutradhar, Pritam Maity (2019) Modelling and Optimization of PSA (Pressure Swing Adsorption) Unit by using Aspen Plus® and Design Expert ® International Journal of Innovative Technology and Exploring Engineering (IJITEE), Volume-8 Issue-4: p64-69 94 Robert Lewis, Timothy Lebrecht (2018) Meeting Nitrogen Demand: On-site Nitrogen generation can be a cost effective option for a wide range of purity and flow requirements http://www.aiche.org/cep 95 R Agrawal and D M Herron (2000) Air liquefaction: Distillation Air Products and Chemicals, Hamilton Boulevard, Allentown, PA, USA, p18951909 96 Ralph T Yang (1987) Gas Separation by Adsorption Processes Butterworth Publishers, Printed in the United States of America 97 Ruthven, D.M (1984) Principles of Adsorption and Adsorption Process New York: Wiley VCH - Publisher 98 Rodney L Mieville, Ken K Robinson (2016) Cacbon molecular sieves and other porous cacbons - Synthesis and Applications Mega-Cacbon Company 103 N 11th Avenue, Suite 114 St Charles, Il 60174 170 99 Radojica Pesic, Tatjana Kaluderovic Radoicic (2015) Pressure drop in packed beds of spherical particles at ambient and elevated air temperature Chemical Industry & Chemical Engineering Quarterly, Vol.21(3): p419-427 100 Scope Ratings AG (2016) Industrial Gases Industry: Globally Strong, Regionally Different http://www.scoperatings.com/ 101 Suzuki, Motoyuki (1990) Adsorption Engineering University of Tokyo 102 Snehal V.Patel, Dr.J.M Patel (2014) Separation of High Purity from Air by Pressure Swing Adsorption on Cacbon Molecular Sieve International Journal of Engineering Research and Technology, vol 3, no 3, pp 450-454 103 Svetlana Ivanova, Robert Lewis (2012) Pressure Swing Adsorption can be a cost-effective method of onsite nitrogen generation for a wide range of purity and flow requirements American Institute of Chemical Engineers, pp 38-42 104 S.Knaebel, Kent (2011) A "How to" Guide for Adsorber Design Dublin, Ohio 43016: Adsorption Research, Inc 105 S Sircar (2001) Applications of Gas Separation by Adsorption for the Future Adsorption Science & Technology Vol 19 No 5, p347-366 106 Snehal V Patel, Dr J M Patel (2014) Separation of High Purity Nitrogen from Air by Pressure Swing Adsorption on Cacbon Molecular Sieves International Journal of Engineering Research & Technology (IJERT), Vol Issue 3, p450-454 107 Salil U.Rege and Raloh T.Yang (1999) Kinetic Separation of Oxygen and Argon Using Molecular Sieve Cacbon Adsorption 6, 15–22 (2000) 2000 Kluwer Academic Publishers Manufactured in The Netherlands 108 Singh R, Saini RP, Saini JS (2006) Nusselt number and friction factor correlations for packed bed solar energy storage system having large sized elements of different shapes Sol Energy; Vol 80(7):p760-71 109 T L P Dantas, F M T Luna (2011) Modeling of the fixed bed adsorption of cacbon dioxide and a cacbon dioxiden nitrogen mixture on zeolite 13X Brazilian Journal of Chemical Engineering, Vol 28, No 03, pp 533 – 544 110 Xiong Yang, Haoyu Wang (2019) Two-Dimensional Modeling of Pressure Swing Adsorption (PSA) Oxygen Generation with Radial-Flow Adsorber Applied Sciences, Vol.9,1153:p1-15 111 Xinyu Phg, Dan S Borgnakke (2013) Possibility of Combustion Furnace Operation with Oxygen-Enriched Gas from Nitrogen Generator ©2013 ACEEE Summer Study on Energy Efficiency in Industry 171 112 Yong-Jin Park, Sang-Jin Lee (2006) Adsorption Equilibria of O 2, N2, and Ar on Cacbon Molecular Sieve and Zeolites 10X, 13X, and LiX Journal of Chemical and Engineering Data, Vol 51, No.3, p1001-1008 113 Zhe XU, Jian-guo CAI, Bing-cai PAN (2013) Review mathematically modeling fixed-bed adsorption in aqueous systems Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), Vol.14(3):p155176 114 Zaid A Abdel-Rahman, Abdulbasit H Mhdi, Heba S Auob (2016) Parametric Study for Nitrogen Separation from Air by Pressure Swing Adsorption Using Cacbon Molecular Sieve Tikrit Journal of Engineering Sciences, Vol 23 (2): p 1-9