Cat.6 Installation Cable - S-STP 450/AWG23, FRNC - Duplex S-STP 450/AWG23, FRNC

KRONE GmbH Beeskowdamm 3-11 09/2003_Subject to changes! Seite 1 von 2 14167 Berlin Tel.: + 49 30 84 53 1 Fax: + 49 30 84 53 23 TECHNICAL DATA Application The KRONE S-STP 450/AWG23 cable is designed for applications up to 450 MHz and provides transmission performance meeting Category 6 specifications. This cables are low skew products, i.e. the difference in propagation delay between the individual pairs is very low. This is increasingly being requested for Gigabit Ethernet. The suitability of the cable for high-bit-rate transmission systems ensures a high degree of future proofing. Additional features are the slim design and low weight of the cables. Each pair is individually shielded (STP). The twisted pairs are additionally enclosed as a group in a braided shield (S-STP) to provide superior shielding performance. The cable thus exceeds the requirements for EN 55022 Class B emission and EN 55024 immunity, enabling networks to be built which are compliant with the standards on electromagnetic compatibility. Characteristics The KRONE S-STP 450/AWG23 cables are available in halogenfree versions with FRNC outer jacket. Every single pair is shielded with foil (STP). Each pair is individually shielded (STP). The twisted pairs are additionally enclosed as a group in a braided shield (S-STP) to provide superior shielding performance. This cables are low skew products, i.e. the difference in propagation delay between the individual pairs is very low. The slim and lightweight design allowed best characteristics in fire retardance. The compact design allows the cables to be installed flat or folded together. Print example (single cable): “KRONE PREMISNET CAT6 S-STP LSZH FR 4P AWG23 SBC ISO/IEC 11801/ EN50173-1 IEC 60332-3 CAT C“ <Woche/Jahr> CA KRONE 7053326255 <METERMARKER> + <Charge> Duplex cable: same as single cable except for part number. Cat.6 Installation Cable - S-STP 450/AWG23, FRNC - Duplex S-STP 450/AWG23, FRNC Copper Conductor AWG 23 Foam/Skin-PE-insulation Twisted pair Braided shield Sheath zero halogen, flame retardant Foil shield 4 twisted pairs S–STP 450/AWG23 4P KRONE GmbH Beeskowdamm 3-11 09/2003_Subject to changes! Seite 2 von 2 14167 Berlin Tel.: + 49 30 84 53 1 Fax: + 49 30 84 53 23 TECHNICAL DATA Cat.6 Installation Cable - S-STP 450/AWG23, FRNC - Duplex S-STP 450/AWG23 FRNC Design Type designation Category Diameter conductor Number of pairs Fire rating (MJ/m) Halogen- free Tensile strength for installation [N] Outside- ? [mm] Weight [kg/km] S-STP 450 / 23 4P LS0H-3 6 AWG 23 4 0,57 Yes 145 7,4 58 Electrical Characteristics at 20° Frequency in MHz 1 10 16 20 31,25 62,5 100 250 450 Attenuation in dB/ 100 m per Standard * 2,1 6,0 7,6 8,5 10,8 15,1 19,9 33,0 - Typical data dB / 100 m 1,8 5,3 6,8 7,6 9,6 13,6 18,0 28,5 40,5 Near-end crosstalk loss in dB per Standard * 66,0 59,3 56,2 54,8 51,9 47,4 44,3 38,3 - Typical data dB / 100 m 100,0 100,0 100,0 100,0 100,0 96,0 93,0 87,0 82,0 PSNEXT in dB/ 100 m per Standard * 64,0 57,3 54,2 52,8 49,9 45,4 42,3 36,3 - Typical data dB / 100 m 98,0 98,0 98,0 98,0 98,0 94,0 93,0 88,0 83,0 ELFEXT in dB/ 100 m per Standard * 66,0 50,0 45,9 44,0 40,1 34,1 30,0 22,0 - Typical data dB / 100 m 93,0 93,0 93,0 93,0 90,0 86,0 83,0 70,0 54,0 PSELFEXT in dB/ 100 m per Standard * 64,0 47,0 43,0 41,0 37,1 31,1 27,0 19,0 - Typical data dB / 100 m 91,0 91,0 91,0 91,0 88,0 84,0 81,0 68,0 52,0 ACR in dB 98,2 94,7 93,2 92,4 90,4 82,4 75,0 58,5 41,5 *) Standard: Requirements on 100 m installed Category 6 cable for Class E cabling links (corresponds to pr EN 50288-5-1 June 2001) Max. loop resistance: 146 Ohm/km Max. resistance difference: 1% Insulation resistance: > 5000 MOhm x km Impedance Zo at 0,064 MHz: 125 Ohm ??20% Impedance Zo at 1 - 100 MHz: 100 Ohm ??15% Impedance Zo at 101 - 250 MHz: 100 Ohm ??18% Transfer impedance: < 10 mOhm per meter bei 10 MHz Longitudinal conversion loss dB/ref. Length = 1000 m: > 46 dB bei 64 kHz Longitudinal conversion loss dB/ref. Length = 100 m: > 40 dB bei 1 MHz Longitudinal conversion loss dB/ref. Length = 100 m: > 20 dB bei 100 MHz Mutual capacity: 43 pF/m Max. capacitance at 0,001 MHz: 1000 pF/km Propagation velocity > 10 MHz (NVP*c): 0,79 c Propagation delay ??10 MHz: 4,2 ns/m Skew: 4 ns/100m Mechanical Wire insulation: Zero halogen foam-skin material Characteristics Sheath material: FRNC Deployment area: Dry and damp rooms Max. temperature range during installation: 0°C up to +50 °C Max. operating temperature: -20 up to +60°C Min. bend radius for single flexure: 40 mm (over flat side) Min. bend radius during installation or pulling: 60 mm (over flat side) Ordering Information Type designation: Cat.6 Installation Cable Delivery: 1000 m on one way drum 500 m on one way drum (Duplex) Ordering number 4 pairs: 7053 3 262-55 7053 3 762-54 (Duplex) . for part number. Cat. 6 Installation Cable - S-STP 450/AWG23, FRNC - Duplex S-STP 450/AWG23, FRNC Copper Conductor AWG 23 Foam/Skin-PE-insulation Twisted. designation: Cat. 6 Installation Cable Delivery: 1000 m on one way drum 500 m on one way drum (Duplex) Ordering number 4 pairs: 7053 3 262 -5 5 7053 3 762 -5 4 (Duplex)