Supplemental Tables for AGMA 2015/915- 1- A02 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915- 1- A02 Accuracy Classification System Tangential Measurement Tolerance Tables for Cylindrical Gears AGMA INFORMATION SHEET (This Information Sheet is NOT an AGMA Standard) Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited American Gear Accuracy Classification System - Tangential Measurement Tolerance Manufacturers Tables for Cylindrical Gears Supplemental Tables for AGMA 2015/915 A02 Association CAUTION NOTICE: AGMA technical publications are subject to constant improvement, revision, or withdrawal as dictated by experience Any person who refers to any AGMA technical publication should be sure that the publication is the latest available from the Association on the subject matter [Tables or other self supporting sections may be quoted or extracted Credit lines should read: Extracted from Supplemental Tables for AGMA 2015/915 A02, Accuracy Classification System Tangential Measurement Tolerance Tables for Cylindrical Gears with the permission of the publisher, the American Gear Manufacturers Association, 1500 King Street, Suite 201, Alexandria, Virginia 22314.] Approved October 20, 2002 ABSTRACT This information sheet provides tolerance tables as a supplement to AGMA 2015 A01, Accuracy Classification System Tangential Measurements for Cylindrical Gears Published by American Gear Manufacturers Association 1500 King Street, Suite 201, Alexandria, Virginia 22314 Copyright 2002 by American Gear Manufacturers Association All rights reserved No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher Printed in the United States of America ISBN: 55589 813 ii Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Contents Page Foreword Scope References Symbols and corresponding terms iv 1 Tables Symbols and definitions Table sequence for each accuracy grade: Single pitch deviation tolerance, fptT Cumulative pitch deviation tolerance, total, FpT Single flank composite tolerance, tooth to tooth, fisT Single flank composite tolerance, total, FisT Profile tolerance, total, FαT Profile slope tolerance, fHαT Profile form tolerance, ffαT Helix tolerance, total, FβT Helix slope tolerance, fHβT Helix form tolerance, ffβT Metric tables (micrometers, mm) 12 22 32 42 52 62 72 82 92 - 11 21 31 41 51 61 71 81 92 101 Tables for grade A2 Tables for grade A3 Tables for grade A4 12 Tables for grade A5 17 Tables for grade A6 22 Tables for grade A7 27 Tables for grade A8 32 Tables for grade A9 37 Tables for grade A10 42 Tables for grade A11 47 Inch tables (ten thousandths of an inch, 0.0001 inch) 102 111 112 121 122 131 132 141 142 151 152 161 162 171 172 181 182 192 192 201 Tables for grade A2 Tables for grade A3 Tables for grade A4 Tables for grade A5 Tables for grade A6 Tables for grade A7 Tables for grade A8 Tables for grade A9 Tables for grade A10 Tables for grade A11 52 57 62 67 72 77 82 87 92 97 iii Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited Supplemental Tables for AGMA 2015/915 A02 AMERICAN GEAR MANUFACTURERS ASSOCIATION Foreword This Information Sheet (supplement) is provided for informational purposes only, and should not be construed to be part of American Gear Manufacturers Association Standard ANSI/AGMA 2015 A01 This supplement provides tables of tolerances for all the different gear accuracy grades While the tables may be used to estimate the tolerances, the actual tolerance should be calculated and rounded according to the formulas in ANSI/AGMA 2015 A01 The range of gear sizes covered by the standard is generally shown in the tables The tolerances are calculated at convenient combinations of module and tolerance diameter, dT The tables are limited to the range of to 1000 teeth, using the simple spur gear relationship that tolerance diameter is approximately equal to the number of teeth times the module The tolerance diameter of helical gears may be significantly higher The helix tables are arbitrarily limited to a minimum facewidth of dT/40 and a maximum face width of × dT, values outside of which are generally beyond normal practice Some combinations of module and diameter or facewidth that are beyond the range shown in these tables may be valid Therefore, limits of application implied by these tables should not be relied upon; the actual limits given in ANSI/AGMA 2015 A01 should be used The tables with inch units cover a slightly narrower range than those given in the metric tables The inch tables are just within the limits given in ANSI/AGMA 2015 A01 The diameter of 98 inches is used because the composite tolerances are limited to a tolerance diameter of 2500 mm (98.425 inches) It should be noted that ANSI/AGMA 2015 A01 uses a fundamentally different evaluation method for tooth to tooth single flank composite tolerances than was used in prior standards; therefore these tolerances should not be directly compared to those in prior standards The first draft of the Supplemental Tables for AGMA 2015/915 A02 was made in January, 2002 It was approved by the AGMA membership in October, 2002 Suggestions for improvement of this information sheet will be welcome They should be sent to the American Gear Manufacturers Association, 1500 King Street, Suite 201, Alexandria, Virginia 22314 iv Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 PERSONNEL of the AGMA Inspection and Handbook Committee Chairman: Edward Lawson M&M Precision Systems ACTIVE MEMBERS D.R Choiniere J Clatworthy B.L Cox T.C Glasener G.G Grana B Hofrichter T Klaves I Laskin Profile Engineering, Inc Gear Metrology, Inc BWXT Y12 LLC Xtek, Incorporated The Gleason Works Arrow Gear Company Milwaukee Gear Consultant S Lindley M May D.A McCarroll D.R McVittie R.W Ott J Rinaldo L.J Smith R.E Smith The Falk Corporation The Gleason Works ZF Industries Gear Engineers, Inc Caterpillar, Inc Atlas Copco Comptec, Inc Consultant R.E Smith & Company, Inc W.E Lake A.J Lemanski G.A Luetkemeier D Matzo P.A McNamara W.J Michaels M Milam S Moore M Nanlawala M Octrue T Okamoto J.A Pennell K.R Price R.S Ramberg V.Z Rychlinski D.H Senkfor S Shariff E Storm R.F Wasilewski F.M Young P Zwart Mitsubishi Gear Tech Center Penn State University Rockwell Automation/Dodge Northwest Gears, Inc Caterpillar, Inc Sundstrand Corporation Amarillo Gear Company Martin Sprocket & Gear, Inc IIT Research Institute/INFAC Centre Technique Des Ind Mec Nippon Gear Company, Ltd Univ of Newcastle Upon Tyne Eastman Kodak Company The Gear Works Seattle, Inc Brad Foote Gear Works, Inc Precision Gear Company PMI Food Equipment Group Consultant Arrow Gear Company Forest City Gear Company Caterpillar, Inc ASSOCIATE MEMBERS M Antosiewicz M.J Barron D Behling M.K Considine R Considine J.S Cowan M.E Cowan B Cowley C Dick H.D Dodd R Green D Gregory B Gudates J.S Hamilton H Harary D Heinrich G Henriot J Horwell S Johnson T Klemm D.E Kosal J Koshiol The Falk Corporation Gear Motions, Inc Hamilton Sundstrand Aero Considine Associates Considine Associates Eaton Corporation Process Equipment Company Mahr Corporation The Horsburgh & Scott Co Caterpillar, Inc R7 Group Gear Products, Inc Fairfield Manufacturing Co., Inc Regal Beloit Corporation NIST Xtek, Incorporated Consultant Brown & Sharpe The Gear Works Seattle, Inc Liebherr National Broach & Machine Co Columbia Gear Corporation v Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited Supplemental Tables for AGMA 2015/915 A02 AMERICAN GEAR MANUFACTURERS ASSOCIATION (This page is intentionally left blank.) vi Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited AMERICAN GEAR MANUFACTURERS ASSOCIATION American Gear Manufacturers Association Accuracy Classification System Tangential Measurement Tolerance Tables for Cylindrical Gears Supplemental Tables for AGMA 2015/915 A02 References The following standards contain provisions which are referenced in the text of this information sheet At the time of publication, the editions indicated were valid All standards are subject to revision, and parties to agreements based on this document are encouraged to investigate the possibility of applying the most recent editions of the standards indicated AGMA 915 A02, Inspection Practices Part 1: Cylindrical Gears Tangential Measurements ANSI/AGMA 2015 A01, Accuracy Classification System Tangential Measurements for Cylindrical Gears ISO 701:1998, International gear notation -Symbols for geometrical data Scope Symbols and corresponding terms This information sheet contains tolerance tables dealing with the tangential measurements of cylindrical involute gear tooth flanks While the tables may be used to estimate the tolerances, the actual tolerance should be calculated and rounded according to the formulas in ANSI/AGMA 2015 A01 It supplements the standard ANSI/AGMA 2015 A01, Accuracy Classification System -Tangential Measurements for Cylindrical Gears The symbols and terms used throughout this document are in basic agreement with the symbols and terms given in ISO 701:1998, International gear notation Symbols for geometrical data See table NOTE: The symbols and definitions used in this document may differ from other AGMA standards The user should not assume that familiar symbols can be used without a careful study of their definitions Table Symbols and definitions Units Symbols b dT FisT FpT FαT FβT ffαT ffβT fHαT fHβT fisT fptT mn Pnd Definition Facewidth (axial) Tolerance diameter Single flank composite tolerance, total Cumulative pitch deviation tolerance, total Profile tolerance, total Helix tolerance, total Profile form tolerance Helix form tolerance Profile slope tolerance Helix slope tolerance Single flank composite tolerance, tooth to tooth Single pitch deviation tolerance Normal module Normal diametral pitch SI mm mm mm mm mm mm mm mm mm mm mm mm mm Inch in in 0.0001 in 0.0001 in 0.0001 in 0.0001 in 0.0001 in 0.0001 in 0.0001 in 0.0001 in 0.0001 in 0.0001 in -in 1 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table Grade A2 Single pitch deviation tolerance, fptT (micrometers, mm) Module, mn 0.5 1.9 1.9 10 1.9 2.1 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 20 1.9 2.1 2.2 25 1.9 2.1 2.2 50 1.9 2.1 2.2 100 2.1 2.2 2.3 150 2.1 2.1 2.2 2.3 200 2.1 2.2 2.3 2.4 250 2.2 2.2 2.3 2.4 Tolerance diameter, dT 300 400 500 600 2.2 2.3 2.4 2.3 2.4 2.5 2.6 2.4 2.5 2.6 2.7 2.5 2.6 2.7 2.8 2.3 2.3 2.4 2.3 2.4 2.5 2.6 2.4 2.5 2.6 2.7 2.4 2.5 2.6 2.7 2.5 2.6 2.7 2.8 2.5 2.6 2.7 2.8 2.6 2.7 2.8 2.9 2.7 2.8 2.9 2.8 2.9 3.1 2.7 2.8 3.5 4.1 2.8 3.1 3.6 4.1 2.9 3.1 3.6 4.2 3.2 3.7 4.2 3.2 3.7 4.3 3.1 3.3 3.9 4.4 4.6 4.7 6.5 4.8 5.5 6.5 7.5 4.8 5.5 6.5 7.5 4.9 5.5 6.5 7.5 10 15 20 25 30 40 50 800 1000 1250 1600 2500 4000 6000 8000 10000 2.7 2.8 2.9 2.9 3.1 3.1 3.2 3.3 3.4 3.9 2.9 3.1 3.2 3.1 3.3 3.4 3.2 3.3 3.4 3.5 3.3 3.4 3.6 3.7 3.5 3.6 3.7 3.9 4.1 4.2 4.3 4.5 4.6 4.7 4.8 5.5 5.5 3.2 3.4 4.5 3.3 3.5 4.6 3.5 3.7 4.2 4.7 3.6 3.8 4.3 4.9 3.8 4.5 4.2 4.7 4.4 4.6 5.5 4.9 5.5 5.5 6.5 6.5 7.5 6.5 5.5 6.5 7.5 5.5 6.5 5.5 5.5 5.5 6.5 7.5 8.5 6.5 6.5 7.5 8.5 9.5 7.5 10 8.5 9.5 11 8.5 10 11 Table Grade A2 Cumulative pitch deviation tolerance, total, FpT (micrometers, mm) Module, mn 0.5 10 15 20 25 30 40 50 7 10 7.5 7.5 20 7.5 7.5 7.5 7.5 25 7.5 7.5 7.5 7.5 50 7.5 7.5 8 100 8 8.5 8.5 150 8.5 9 200 9.5 9.5 9.5 250 10 10 10 10 Tolerance diameter, dT 300 400 500 600 10 11 12 10 11 12 13 10 12 13 14 11 12 13 14 7.5 8 8 8.5 8.5 8.5 9 9 9.5 9.5 9.5 9.5 10 10 10 10 10 10 11 11 11 11 12 12 12 12 13 13 13 13 8.5 8.5 9 9.5 10 9.5 9.5 10 11 10 10 11 11 11 11 11 12 11 11 12 12 12 12 13 13 11 12 12 12 13 12 13 14 15 13 13 14 16 14 14 16 17 800 1000 1250 1600 2500 4000 6000 8000 10000 15 15 15 17 17 17 18 18 20 20 25 14 14 14 14 15 16 16 16 17 17 17 17 19 19 19 19 21 21 21 21 25 25 25 25 31 31 31 31 37 37 13 13 14 14 14 14 15 15 16 16 17 17 17 18 18 19 19 19 20 20 21 21 22 22 25 26 26 27 31 31 32 33 38 38 38 39 43 43 44 44 48 48 49 15 16 17 18 16 16 18 19 18 18 19 20 19 20 21 22 21 21 22 23 23 23 24 25 27 28 29 30 33 34 35 36 39 40 41 42 45 45 46 47 49 50 51 52 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table Grade A2 Single flank composite tolerance, tooth to tooth, fisT (micrometers, µm) Module, mn 0.5 0.7 0.7 10 0.7 0.7 0.7 Tolerance diameter, dT 200 250 300 400 0.9 1 1.1 0.9 1 1.1 0.9 1 1.2 1 1.1 1.2 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 20 0.7 0.7 0.7 0.8 25 0.7 0.7 0.8 0.8 50 0.8 0.8 0.8 0.8 100 0.8 0.8 0.8 0.8 150 0.9 0.9 0.9 0.9 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.9 0.9 0.9 0.9 0.9 0.9 0.9 0.9 1 1 1 1 1.1 1.1 1.1 1.1 0.8 0.9 0.9 0.9 1 1 1.1 1 1.1 1.1 1.1 1.1 1.1 1.2 1.1 1.2 1.2 1.2 1.3 1.2 1.3 1.4 1.5 10 15 20 25 30 40 50 500 1.2 1.2 1.3 1.3 600 800 1000 1250 1600 2500 1.4 1.4 1.4 1.6 1.6 1.6 1.8 1.8 1.8 2.1 2.1 2.4 2.4 3.4 1.2 1.2 1.2 1.2 1.3 1.3 1.3 1.3 1.4 1.4 1.4 1.4 1.6 1.6 1.6 1.6 1.8 1.8 1.8 1.8 2.1 2.1 2.1 2.1 2.4 2.5 2.5 2.5 3.4 3.4 3.4 3.4 1.1 1.1 1.2 1.2 1.2 1.2 1.3 1.3 1.3 1.3 1.4 1.4 1.4 1.4 1.5 1.6 1.6 1.7 1.7 1.8 1.9 1.9 1.9 2.1 2.1 2.2 2.2 2.5 2.5 2.6 2.6 3.4 3.5 3.5 3.6 1.3 1.3 1.4 1.6 1.4 1.4 1.6 1.7 1.5 1.6 1.7 1.8 1.6 1.7 1.8 1.9 1.8 1.9 2.1 2.1 2.2 2.3 2.3 2.4 2.5 2.6 2.7 2.7 2.8 2.9 3.6 3.7 3.8 3.9 Table Grade A2 Single flank composite tolerance, total, FisT (micrometers, µm) Module, mn 0.5 10 15 20 25 30 40 50 8 10 8 20 8 8.5 25 8 8.5 8.5 50 8.5 8.5 8.5 8.5 100 9 9.5 150 9.5 9.5 10 10 Tolerance diameter, dT 200 250 300 400 10 11 11 13 10 11 11 13 10 11 12 13 10 11 12 13 8.5 8.5 8.5 9 9 9.5 9.5 9.5 10 10 10 10 10 11 11 11 11 11 11 11 12 12 12 12 12 13 13 13 13 14 14 14 14 15 15 15 16 18 18 18 18 20 20 20 20 23 23 23 23 27 27 27 27 37 38 38 38 9.5 9.5 10 10 11 11 10 11 11 12 11 11 12 12 12 12 12 13 12 12 13 14 13 14 14 15 15 15 15 16 16 16 17 17 18 18 19 19 20 21 21 22 23 24 24 25 27 28 28 29 38 38 39 39 12 13 13 14 15 14 14 15 17 14 15 16 17 15 16 17 18 17 17 18 19 18 18 19 21 20 21 22 23 22 23 24 25 25 26 27 28 29 30 31 32 40 40 42 43 500 14 14 14 14 600 800 1000 1250 1600 2500 15 15 15 17 17 17 20 20 20 23 23 27 27 37 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table Grade A2 Profile tolerance, total, FαT (micrometers, µm) Module, mn 0.5 1.2 1.6 10 1.3 1.6 2.1 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 20 1.4 1.7 2.2 2.6 25 1.4 1.8 2.2 2.6 50 1.6 1.9 2.4 2.8 100 1.8 2.2 2.6 150 2.3 2.8 3.2 200 2.1 2.5 2.9 3.3 250 2.3 2.6 3.1 3.4 Tolerance diameter, dT 300 400 500 600 800 2.4 2.6 2.8 2.7 2.9 3.1 3.3 3.6 3.2 3.4 3.6 3.8 3.6 3.8 3.9 4.1 4.4 2.9 2.9 3.2 3.1 3.3 3.6 3.8 3.3 3.6 3.8 3.5 3.7 4.2 3.6 3.9 4.1 4.3 3.7 4.2 4.5 3.9 4.1 4.4 4.6 4.1 4.3 4.6 4.8 4.2 4.5 4.8 4.4 4.7 4.9 4.4 4.2 4.6 5.5 4.4 4.8 5.5 6.5 4.5 4.9 5.5 6.5 4.7 6.5 4.8 6.5 5.5 5.5 6.5 7 7.5 7.5 8.5 7.5 8.5 9.5 7.5 9.5 7.5 10 7.5 10 10 15 20 25 30 40 50 1000 1250 1600 2500 4000 6000 8000 10000 3.8 4.3 4.7 4.6 5 5.5 4.7 5 5.5 5 5.5 5.5 5.5 5.5 6 5.5 6 6.5 6.5 6.5 7 7.5 7.5 8 9.5 5.5 5.5 6.5 5.5 7.5 6.5 6.5 7.5 6.5 7.5 8.5 7.5 7.5 8.5 8.5 8.5 9.5 10 9.5 10 11 11 10 11 12 12 12 12 13 8.5 9.5 10 8.5 9.5 10 8.5 10 11 8.5 10 11 9.5 11 11 10 10 11 12 11 11 12 13 12 12 13 14 13 13 14 15 14 14 15 16 Table Grade A2 Profile slope tolerance, fHαT (micrometers, µm) Module, mn 0.5 10 15 20 25 30 40 50 0.8 10 0.8 1.3 20 0.9 1.1 1.4 1.6 25 0.9 1.1 1.4 1.6 50 1.2 1.5 1.8 100 1.2 1.4 1.7 1.9 150 1.3 1.5 1.8 200 1.4 1.6 1.9 2.1 250 1.5 1.7 2.2 Tolerance diameter, dT 300 400 500 600 1.5 1.7 1.8 1.7 1.9 2.1 2.2 2.3 2.4 2.3 2.4 2.5 2.6 1.8 1.8 1.9 2.1 2.3 2.4 2.1 2.3 2.4 2.5 2.2 2.4 2.5 2.7 2.3 2.5 2.6 2.7 2.4 2.5 2.7 2.8 2.4 2.6 2.8 2.9 2.6 2.7 2.9 2.7 2.9 3.2 2.5 2.8 2.7 2.9 3.4 3.8 2.8 3.5 3.9 2.9 3.1 3.6 3.2 3.7 4.1 3.3 3.8 4.2 3.2 3.4 3.9 4.3 4.3 4.7 4.4 4.7 5.5 4.5 4.8 5.5 4.6 4.9 5.5 4.7 5.5 800 1000 1250 1600 2500 4000 6000 8000 10000 2.3 2.6 2.8 2.4 2.7 2.9 3.2 3.2 3.4 3.9 2.8 3.1 3.3 3.2 3.3 3.4 3.2 3.3 3.5 3.6 3.3 3.5 3.7 3.8 3.6 3.7 3.9 4.1 4.2 4.4 4.5 4.7 4.9 5 5.5 3.3 3.5 4.4 3.4 3.6 4.1 4.6 3.6 3.8 4.3 4.7 3.7 4.5 4.9 3.9 4.2 4.7 4.2 4.4 4.9 5.5 4.7 4.9 5.5 5.5 5.5 6.5 6 6.5 6.5 7.5 7.5 8.5 4.8 6.5 4.9 5.5 6.5 5.5 6.5 5.5 5.5 6.5 5.5 6.5 5.5 6.5 6.5 7.5 7 8.5 7.5 8.5 8.5 9.5 8.5 9.5 10 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 174 Grade A9 Single flank composite tolerance, tooth to tooth, fisT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.4 3.4 3.4 3.4 3.7 3.7 3.7 3.7 3.9 3.9 3.9 3.9 4.1 4.1 4.1 4.2 4.4 4.4 4.4 4.4 4.6 4.6 4.6 4.6 5 5 5.5 5.5 5.5 5.5 6 7 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.4 3.4 3.4 3.5 3.5 3.5 3.7 3.7 3.7 3.7 3.9 3.9 4 4.2 4.2 4.2 4.2 4.4 4.4 4.4 4.4 4.6 4.7 4.7 4.7 5 5 5.5 5.5 5.5 5.5 6 6 7 7 3.4 3.4 3.4 3.4 3.5 3.5 3.5 3.6 3.7 3.7 3.8 3.8 3.9 4 4.1 4.2 4.2 4.3 4.3 4.4 4.5 4.5 4.5 4.6 4.7 4.7 4.8 4.9 5 5.5 5.5 5.5 5.5 5.5 6.5 6.5 6.5 6.5 4.2 4.5 4.7 5.5 4.9 5.5 6.5 6.5 5.5 6.5 6.5 7.5 6.5 7.5 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 8 8 9 9 10 10 10 7 7 8 8 9.5 9.5 9.5 9.5 10 10 11 11 15 15 15 15 7.5 8.5 8.5 10 9.5 10 11 11 12 12 16 16 17 50 60 98 Table 175 Grade A9 Single flank composite tolerance, total, FisT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 20 16 14 12 10 0.6 88 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 35 35 35 35 36 36 36 36 36 36 36 36 36 36 37 38 38 38 38 40 40 40 40 43 43 43 43 45 46 46 46 48 48 48 48 51 51 51 51 56 56 56 56 61 61 61 62 68 68 68 75 75 88 36 36 36 36 37 37 37 37 37 37 37 38 38 38 38 41 41 41 41 43 43 44 44 46 46 46 46 49 49 49 49 51 51 51 52 56 57 57 57 62 62 62 62 68 68 69 69 75 75 75 75 88 88 88 89 101 101 102 102 115 115 115 37 37 37 38 38 39 39 39 41 41 42 42 43 44 44 45 46 47 47 47 49 49 49 50 51 52 52 53 54 57 57 58 59 62 63 63 64 69 69 70 71 76 76 76 78 89 89 90 91 102 102 103 104 115 115 116 117 165 166 166 167 47 49 56 52 58 54 61 70 57 64 72 62 69 78 68 74 83 74 81 90 81 87 96 94 101 109 107 114 123 120 127 136 171 177 186 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 176 Grade A9 Profile tolerance, total, FαT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 5.5 6.5 6 6.5 7.5 6.5 6.5 6.5 7.5 7.5 8.5 8.5 10 9.5 10 11 9.5 10 11 11 10 11 11 12 11 11 12 12 12 12 13 13 13 13 13 14 14 14 15 15 16 17 8.5 8.5 9.5 10 8.5 9.5 10 9.5 10 10 11 10 11 11 12 11 12 12 13 12 12 13 13 12 13 13 14 13 14 14 14 14 14 15 15 15 15 16 16 16 16 17 17 16 17 17 18 11 12 11 12 13 12 13 14 16 13 14 15 17 13 14 16 18 14 15 16 19 15 16 17 19 15 16 18 20 16 17 18 21 17 18 19 22 18 19 20 23 23 23 31 24 31 25 32 39 25 33 40 26 33 41 27 34 42 28 35 43 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 150 250 18 18 19 19 19 20 20 21 21 21 22 19 20 21 23 20 21 23 25 21 22 24 26 29 36 43 30 38 45 31 39 46 300 390 23 24 25 27 26 27 29 31 33 35 41 33 40 47 36 44 51 40 48 55 47 54 61 49 57 64 54 61 68 98 150 250 300 390 31 36 41 34 39 43 Table 177 Grade A9 Profile slope tolerance, fHαT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 20 16 14 12 10 0.6 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 50 60 3.6 3.8 4.1 3.8 4.3 4.7 4.1 4.3 4.6 4.2 4.4 4.7 4.6 4.9 5.5 5.5 5.5 6 6 6.5 6.5 6.5 6.5 6.5 7 7.5 7 7.5 7.5 7.5 8.5 8.5 8.5 9 9.5 9.5 10 11 5.5 5.5 5.5 5.5 6.5 5.5 6 6.5 6.5 6.5 6.5 7.5 7.5 7.5 8 7.5 8 8.5 8.5 8.5 8.5 9 9 9.5 10 9.5 9.5 10 10 10 10 11 11 10 11 11 11 11 12 12 12 12 13 13 13 13 14 14 7.5 7.5 8.5 7.5 10 8.5 9.5 11 8.5 10 11 9.5 10 12 9.5 10 11 12 9.5 10 11 13 10 11 12 13 11 11 12 14 11 12 13 14 12 12 13 15 13 13 14 16 14 14 15 17 14 15 16 17 17 17 18 20 21 22 26 14 15 19 15 20 16 20 25 16 21 25 16 21 26 17 22 26 18 22 27 18 23 27 19 24 28 20 25 29 21 25 30 23 28 32 26 30 35 30 34 39 89 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 178 Grade A9 Profile form tolerance, ffαT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 4.3 4.5 4.9 4.5 4.8 5.5 4.9 5.5 5.5 5.5 5.5 6 6.5 6.5 6.5 7.5 7 7.5 7.5 7.5 8.5 8 8.5 8.5 8.5 9.5 9.5 9.5 10 9.5 10 10 11 11 11 12 12 12 13 6.5 6.5 7.5 7.5 6.5 7.5 7.5 8.5 8.5 9 8.5 9.5 10 9.5 10 10 9.5 10 10 11 10 10 11 11 11 11 11 12 11 12 12 13 12 12 13 13 13 13 13 14 8.5 8.5 10 9.5 11 13 10 11 12 13 10 11 12 14 11 12 13 15 11 12 13 15 12 12 14 15 12 13 14 16 13 14 15 17 14 15 16 17 18 18 24 19 24 19 25 31 19 25 31 20 26 32 21 27 32 22 27 33 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 150 250 14 14 15 15 15 15 16 16 16 17 17 14 15 16 18 16 16 17 19 17 17 18 20 18 18 19 21 20 21 22 24 25 27 32 22 28 34 23 29 35 24 30 36 25 31 37 28 34 40 31 37 43 36 42 48 300 390 38 44 50 41 47 53 Table 179 Grade A9 Helix tolerance, total, FβT (ten thousandths of an inch, 0.0001 inch) Face width, id h b 0.16 0.25 0.5 0.75 1.5 10 15 20 30 39 90 0.2 9.5 11 Tolerance diameter, dT 10 12 16 0.4 9.5 11 11 0.8 9.5 10 11 12 9.5 10 11 12 9.5 10 11 12 10 11 12 13 11 11 12 13 20 25 11 12 13 12 13 13 13 14 12 12 13 14 12 14 14 16 13 14 15 16 13 14 15 17 14 15 16 17 14 15 16 18 14 15 16 18 18 20 18 20 24 19 21 24 28 19 21 25 28 31 30 40 50 60 98 13 14 14 14 15 14 15 16 18 15 16 17 18 15 16 17 19 19 21 25 28 19 22 25 29 20 22 26 29 31 37 32 37 32 37 41 150 16 17 18 19 16 17 18 20 17 18 19 20 18 19 21 20 21 23 20 22 26 30 21 23 26 30 21 23 27 30 22 24 27 31 22 24 28 32 23 25 29 32 24 27 30 34 26 29 32 36 33 38 41 33 38 42 33 38 42 34 39 43 35 40 43 35 40 44 37 42 46 39 44 48 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 180 Grade A9 Helix slope tolerance, fHβT (ten thousandths of an inch, 0.0001 inch) Face width, id h b 0.16 0.25 0.5 0.75 0.2 6.5 7.5 1.5 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 0.4 6.5 7.5 0.8 6.5 7.5 8.5 6.5 8.5 7.5 8.5 7.5 7.5 8.5 7.5 8.5 9 9.5 8.5 9.5 9.5 8.5 9.5 10 9.5 10 11 10 11 12 9.5 10 11 12 9.5 10 11 12 10 11 11 12 10 11 12 13 13 14 13 15 17 13 15 17 20 13 15 18 20 22 10 15 20 30 39 Tolerance diameter, dT 10 12 16 20 25 30 40 50 60 98 9.5 10 9.5 10 11 10 11 12 13 11 11 12 13 11 12 12 13 14 15 18 20 14 15 18 20 14 16 18 21 22 26 23 26 23 27 29 150 11 12 13 14 11 12 13 14 12 13 13 14 13 14 15 14 15 16 14 16 19 21 15 16 19 21 15 17 19 22 15 17 20 22 16 17 20 22 16 18 20 23 17 19 22 24 19 20 23 25 23 27 30 23 27 30 24 27 30 24 28 31 25 28 31 25 29 31 26 30 33 28 31 34 150 Table 181 Grade A9 Helix form tolerance, ffβT (ten thousandths of an inch, 0.0001 inch) Face width, id h b 0.16 0.25 0.5 0.75 1.5 10 15 20 30 39 0.2 6.5 7.5 Tolerance diameter, dT 10 12 16 0.4 6.5 7.5 0.8 6.5 7.5 8.5 6.5 8.5 7.5 8.5 7.5 7.5 8.5 7.5 8.5 20 25 9.5 8.5 9.5 9.5 8.5 9.5 10 9.5 10 11 10 11 12 9.5 10 11 12 9.5 10 11 12 10 11 11 12 10 11 12 13 13 14 13 15 17 13 15 17 20 13 15 18 20 22 30 40 50 60 98 9.5 10 9.5 10 11 10 11 12 13 11 11 12 13 11 12 12 13 11 12 13 14 11 12 13 14 12 13 13 14 13 14 15 14 15 16 14 15 18 20 14 15 18 20 14 16 18 21 14 16 19 21 15 16 19 21 15 17 19 22 15 17 20 22 16 17 20 22 16 18 20 23 17 19 22 24 19 20 23 25 22 26 23 26 23 27 29 23 27 30 23 27 30 24 27 30 24 28 31 25 28 31 25 29 31 26 30 33 28 31 34 91 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 182 Grade A10 Single pitch deviation tolerance, fptT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 13 13 13 13 13 13 13 13 13 13 13 13 14 14 14 14 14 14 14 14 14 15 15 15 15 15 15 15 16 16 16 16 17 17 18 12 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 14 13 14 14 14 14 14 14 14 14 14 14 15 14 15 15 15 15 15 16 16 16 16 16 16 16 17 17 17 17 17 17 18 13 14 13 14 15 14 14 15 16 14 14 15 17 14 15 15 17 15 15 16 17 15 15 16 18 15 16 16 18 16 16 17 19 17 17 18 19 17 18 18 20 21 21 30 21 30 22 30 42 22 31 42 23 31 43 23 32 43 24 33 44 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 150 250 18 18 19 19 19 19 20 20 20 21 21 18 18 19 21 19 20 20 22 20 21 21 23 21 21 22 24 24 24 25 26 28 30 34 25 33 45 26 34 46 27 35 47 28 36 48 31 39 51 34 42 54 39 47 58 300 390 41 49 61 44 52 64 300 390 267 276 287 301 310 321 Table 183 Grade A10 Cumulative pitch deviation tolerance, total, FpT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 20 16 14 12 10 0.6 92 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 50 60 45 45 45 46 46 46 46 46 46 46 47 47 47 47 47 48 48 48 49 52 52 52 52 55 55 55 55 58 59 59 59 62 62 62 62 65 65 65 66 72 72 72 72 79 79 79 79 86 86 86 93 93 105 46 46 46 47 47 47 47 47 47 47 48 49 49 49 49 52 52 53 53 56 56 56 56 59 59 59 60 62 63 63 63 66 66 66 66 73 73 73 73 79 79 80 80 87 87 87 87 93 93 94 94 48 48 48 48 49 50 50 51 52 53 53 54 56 56 57 58 59 60 60 61 62 63 64 64 66 67 67 68 69 73 74 75 76 80 80 81 83 87 88 89 90 60 63 72 67 75 70 78 90 73 82 93 80 89 100 87 95 107 94 103 114 98 150 250 105 105 106 106 116 116 116 116 125 125 126 94 95 95 97 106 106 107 109 116 117 118 119 126 126 127 129 156 157 157 159 190 192 242 101 109 121 113 121 133 123 132 143 133 141 153 163 171 183 196 204 216 246 254 266 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 184 Grade A10 Single flank composite tolerance, tooth to tooth, fisT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 4.5 4.5 4.5 4.6 4.6 4.6 4.6 4.6 4.6 4.6 4.7 4.7 4.7 4.7 4.7 4.8 4.8 4.8 4.9 5 5 5.5 5.5 5.5 5.5 6 6 6 6 6.5 6.5 6.5 6.5 7 7 8 8 8.5 8.5 9.5 9.5 11 4.6 4.6 4.6 4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.8 4.9 4.9 4.9 4.9 5 5.5 5.5 5.5 5.5 5.5 5.5 6 6 6.5 6.5 6.5 6.5 6.5 6.5 6.5 7.5 7.5 7.5 7.5 8 8 9 9 9.5 9.5 9.5 9.5 4.8 4.8 4.8 4.8 4.9 5 5 5.5 5.5 5.5 5.5 5.5 5.5 6 6 6 6.5 6.5 6.5 6.5 6.5 6.5 7 7.5 7.5 7.5 7.5 8 8.5 9 9 6.5 6.5 7.5 7.5 9.5 10 8.5 9.5 11 9.5 10 12 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 11 11 11 11 13 13 13 13 15 15 15 9.5 10 10 10 11 11 12 12 13 13 13 13 15 15 15 15 21 21 21 22 10 11 12 12 13 14 14 15 16 15 16 17 22 23 24 50 60 98 Table 185 Grade A10 Single flank composite tolerance, total, FisT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 20 16 14 12 10 0.6 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 50 50 50 50 50 50 51 51 51 51 51 51 51 51 52 53 53 53 54 57 57 57 57 61 61 61 61 64 64 65 65 68 68 68 68 72 72 72 72 79 79 79 80 87 87 87 87 96 96 96 106 106 124 51 51 51 51 52 52 52 52 52 52 52 54 54 54 54 57 58 58 58 61 61 62 62 65 65 65 65 69 69 69 69 72 73 73 73 80 80 80 80 87 87 88 88 97 97 97 97 106 106 106 107 125 125 125 125 143 144 144 144 162 162 163 52 53 53 53 54 55 55 56 57 58 59 60 61 62 63 63 65 66 66 67 69 70 70 71 72 73 74 75 76 81 81 82 84 88 89 89 91 98 98 99 100 107 107 108 110 126 126 127 128 144 145 145 147 163 163 164 166 234 234 235 237 66 70 79 73 83 77 86 99 81 90 103 88 98 110 96 105 117 105 114 127 114 124 136 133 142 155 152 161 173 170 180 192 241 251 263 93 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 186 Grade A10 Profile tolerance, total, FαT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 8.5 8.5 9.5 10 9.5 10 11 9.5 10 11 10 11 11 12 12 12 13 14 13 13 14 15 14 14 15 16 15 15 16 17 15 16 16 17 17 17 18 19 18 18 19 20 20 20 21 21 22 25 11 12 13 12 13 13 14 12 13 14 14 13 14 15 15 15 15 16 17 16 17 17 18 17 18 18 19 17 18 19 20 18 19 20 20 19 20 21 22 21 22 22 23 22 23 24 24 23 24 25 25 15 16 15 17 19 16 18 20 23 18 19 21 24 19 20 22 26 20 21 23 27 21 22 24 27 21 23 25 28 23 24 26 29 24 25 27 31 25 27 29 32 32 33 44 34 44 35 45 56 36 46 56 37 47 58 38 49 59 39 50 60 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 150 250 25 26 27 28 27 28 29 29 30 30 31 26 28 30 33 29 30 32 35 30 32 34 37 40 51 61 43 53 64 44 55 65 300 390 32 33 35 39 37 39 41 44 46 50 59 46 57 67 51 62 72 57 68 78 66 77 87 70 80 91 76 86 97 98 150 250 300 390 44 51 57 48 55 61 Table 187 Grade A10 Profile slope tolerance, fHαT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 20 16 14 12 10 0.6 94 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 50 60 5.5 5.5 5.5 6.5 6 6.5 6 6.5 7.5 6.5 7.5 7.5 8 8.5 9.5 9 9.5 10 9.5 9.5 10 11 10 10 11 11 11 11 11 12 11 12 12 13 13 13 14 14 14 16 7.5 7.5 8.5 7.5 8.5 8.5 8.5 9.5 10 9.5 10 10 11 10 11 11 11 11 11 12 12 11 12 12 13 12 12 13 13 12 13 13 14 13 14 14 15 14 15 15 15 15 15 16 16 16 17 17 18 17 18 18 19 19 19 20 9.5 10 10 11 12 10 11 13 15 11 12 13 15 12 13 14 16 13 13 15 17 13 14 15 17 14 14 16 18 14 15 17 19 15 16 17 19 16 17 18 20 17 18 19 21 18 19 20 22 19 20 21 23 20 21 22 25 24 25 26 28 30 32 37 20 21 27 21 28 22 29 35 22 29 36 23 30 36 24 31 37 25 31 38 26 32 39 27 34 40 28 35 41 29 36 42 33 39 46 36 43 49 42 48 55 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 188 Grade A10 Profile form tolerance, ffαT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 6.5 6.5 7.5 7.5 8.5 7.5 8.5 8 9.5 9.5 10 11 10 10 11 12 11 11 11 12 11 12 12 13 12 12 13 13 13 13 14 14 14 14 15 15 15 16 16 17 17 19 8.5 9.5 10 10 10 11 9.5 10 11 11 10 11 11 12 11 12 12 13 12 13 13 14 13 14 14 15 13 14 15 15 14 15 15 16 15 16 16 17 16 17 17 18 17 18 18 19 18 19 19 20 12 13 12 13 14 13 14 15 18 14 15 16 19 15 16 17 20 15 16 18 21 16 17 19 21 17 18 19 22 18 19 20 23 19 20 21 24 20 21 22 25 25 26 34 26 35 27 35 43 28 36 44 29 37 45 29 38 46 30 39 47 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 150 250 19 20 21 21 21 22 22 23 23 23 24 20 21 23 26 22 23 25 27 23 25 26 29 25 26 27 30 29 30 31 34 36 39 45 31 40 48 33 41 49 34 43 51 36 44 52 40 48 56 44 53 61 51 59 68 300 390 54 62 70 59 67 75 Table 189 Grade A10 Helix tolerance, total, FβT (ten thousandths of an inch, 0.0001 inch) Face width, id h b 0.16 0.25 0.5 0.75 1.5 10 15 20 30 39 0.2 13 13 15 Tolerance diameter, dT 10 12 16 0.4 13 14 15 16 0.8 13 14 15 16 13 14 15 17 14 14 16 17 14 15 17 18 15 16 17 18 20 25 16 18 19 16 18 19 18 19 17 17 19 20 18 19 20 23 18 20 21 23 19 20 22 24 19 21 22 24 20 21 23 25 20 22 23 25 25 28 26 29 34 26 29 34 39 27 30 35 40 44 30 40 50 60 98 19 20 19 20 21 20 22 23 25 21 23 24 26 21 23 24 27 27 30 35 40 27 31 36 41 28 31 36 41 45 52 45 52 45 53 58 150 22 24 25 27 23 24 26 28 24 25 26 29 26 27 30 28 30 33 29 32 37 42 29 32 37 42 30 33 38 43 31 34 39 44 31 35 40 45 32 35 40 45 35 38 43 48 37 40 45 50 46 53 59 47 54 59 47 54 60 48 55 61 49 56 61 50 57 62 52 59 65 55 62 67 95 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 190 Grade A10 Helix slope tolerance, fHβT (ten thousandths of an inch, 0.0001 inch) Face width, id h b 0.16 0.25 0.5 0.75 0.2 9.5 11 1.5 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 0.4 9.5 11 12 0.8 9.5 10 11 12 9.5 10 11 12 10 10 11 12 10 11 12 13 11 11 12 13 11 12 13 12 13 14 13 14 12 12 14 15 13 14 15 16 13 14 15 17 13 14 15 17 14 15 16 17 14 15 16 18 14 15 16 18 18 20 18 21 24 19 21 25 28 19 21 25 28 31 10 15 20 30 39 Tolerance diameter, dT 10 12 16 20 25 30 40 50 60 98 13 14 14 15 15 14 16 17 18 15 16 17 19 15 16 17 19 19 22 25 29 20 22 25 29 20 22 26 29 32 37 32 37 32 37 41 150 16 17 18 19 16 17 18 20 17 18 19 20 18 19 21 20 22 23 20 23 26 30 21 23 27 30 21 23 27 31 22 24 28 31 22 25 28 32 23 25 29 32 25 27 30 34 26 29 32 36 33 38 42 33 38 42 34 39 43 34 39 43 35 40 44 35 40 44 37 42 46 39 44 48 150 Table 191 Grade A10 Helix form tolerance, ffβT (ten thousandths of an inch, 0.0001 inch) Face width, id h b 0.16 0.25 0.5 0.75 1.5 10 15 20 30 39 96 0.2 9.5 11 Tolerance diameter, dT 10 12 16 0.4 9.5 11 12 0.8 9.5 10 11 12 9.5 10 11 12 10 10 11 12 10 11 12 13 11 11 12 13 20 25 11 12 13 12 13 14 13 14 12 12 14 15 13 14 15 16 13 14 15 17 13 14 15 17 14 15 16 17 14 15 16 18 14 15 16 18 18 20 18 21 24 19 21 25 28 19 21 25 28 31 30 40 50 60 98 13 14 14 15 15 14 16 17 18 15 16 17 19 15 16 17 19 16 17 18 19 16 17 18 20 17 18 19 20 18 19 21 20 22 23 19 22 25 29 20 22 25 29 20 22 26 29 20 23 26 30 21 23 27 30 21 23 27 31 22 24 28 31 22 25 28 32 23 25 29 32 25 27 30 34 26 29 32 36 32 37 32 37 32 37 41 33 38 42 33 38 42 34 39 43 34 39 43 35 40 44 35 40 44 37 42 46 39 44 48 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 192 Grade A11 Single pitch deviation tolerance, fptT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 17 17 17 17 17 17 17 17 17 17 18 17 17 17 18 17 17 18 18 18 18 18 18 18 18 19 19 19 19 19 19 19 19 20 20 20 20 20 20 21 21 21 21 22 22 22 22 23 23 23 24 24 26 18 18 18 18 18 18 19 18 18 18 19 18 18 19 19 19 19 19 19 19 19 20 20 19 20 20 20 20 20 20 21 20 21 21 21 21 22 22 22 22 23 23 23 23 24 24 24 24 25 25 25 19 20 19 20 21 19 20 21 23 20 20 21 23 20 21 22 24 21 21 22 24 21 22 23 25 22 22 23 25 23 23 24 26 24 24 25 27 25 25 26 28 29 30 42 30 42 31 43 59 31 43 59 32 44 60 33 45 61 34 46 62 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 150 250 26 26 26 27 27 28 28 28 29 29 29 25 26 27 29 27 28 29 31 28 29 30 32 30 30 31 33 34 34 35 37 40 42 49 35 47 63 37 49 65 38 50 66 39 51 67 43 55 71 48 60 76 55 67 83 300 390 58 70 86 62 74 90 300 390 378 390 406 426 438 454 Table 193 Grade A11 Cumulative pitch deviation tolerance, total, FpT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 20 16 14 12 10 0.6 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 50 60 64 64 64 64 65 65 65 65 66 66 66 66 66 66 66 68 68 69 69 73 73 73 74 78 78 78 78 83 83 83 83 87 88 88 88 92 92 93 93 102 102 102 102 111 111 112 112 122 122 122 131 132 149 65 65 66 66 66 67 67 67 67 67 67 69 69 70 70 74 74 74 75 79 79 79 79 83 84 84 84 88 88 89 89 93 93 94 94 103 103 103 103 112 112 112 113 122 123 123 123 132 132 132 133 67 68 68 68 69 70 71 72 74 75 76 77 79 80 80 81 83 85 85 86 88 89 90 91 93 94 95 96 98 104 104 105 107 113 114 115 117 124 124 125 127 85 89 101 94 106 99 111 127 104 116 132 113 125 141 123 135 151 133 145 161 98 150 250 149 149 149 150 164 164 164 164 177 177 178 133 134 135 137 150 151 152 154 165 165 166 168 178 179 180 182 221 221 222 224 269 271 342 143 155 171 160 172 188 174 186 202 188 200 216 230 242 258 277 289 305 348 360 376 97 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 194 Grade A11 Single flank composite tolerance, tooth to tooth, fisT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 7 7 7.5 7.5 7.5 7.5 8 8 8.5 8.5 8.5 8.5 8.5 9 9 9.5 9.5 10 10 10 10 11 11 11 11 12 12 12 14 14 16 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 7 7 7.5 7.5 7.5 7.5 8 8 8.5 8.5 8.5 8.5 9 9 9.5 9.5 9.5 9.5 10 10 10 10 11 11 11 11 12 12 12 12 14 14 14 14 6.5 7 7 7 7.5 7.5 7.5 7.5 8 8 8.5 8.5 8.5 8.5 9 9 9.5 9.5 9.5 9.5 10 10 10 11 11 11 11 11 12 13 13 13 13 8.5 10 9.5 11 10 11 13 10 12 13 11 13 14 12 13 15 13 15 16 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 16 16 16 16 18 18 18 18 21 21 21 14 14 14 14 16 16 16 16 19 19 19 19 21 21 21 21 30 30 30 30 15 16 17 17 18 20 19 21 22 22 23 25 31 32 34 50 60 98 Table 195 Grade A11 Single flank composite tolerance, total, FisT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 20 16 14 12 10 0.6 98 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 70 70 71 71 71 71 71 72 72 72 73 72 73 73 73 75 75 75 76 80 81 81 81 86 86 86 86 91 91 91 92 96 96 97 97 102 102 102 102 112 112 112 113 123 123 123 123 136 136 136 149 150 176 72 72 72 73 73 73 74 73 74 74 74 76 76 76 77 81 82 82 82 86 87 87 87 92 92 92 93 97 97 98 98 102 103 103 103 113 113 113 114 123 124 124 124 137 137 137 137 150 150 150 151 176 177 177 177 203 203 203 203 229 230 230 74 75 75 75 76 77 78 79 81 82 83 84 86 88 88 90 92 93 94 95 97 98 99 100 102 104 104 105 108 114 115 116 118 125 125 126 129 138 139 140 142 151 152 153 155 178 178 179 181 204 205 206 208 230 231 232 234 331 331 332 335 93 98 112 104 117 109 122 140 114 127 145 125 138 156 135 148 166 148 162 179 162 175 192 188 201 219 214 228 245 241 254 272 341 354 372 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 196 Grade A11 Profile tolerance, total, FαT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 11 12 13 12 12 13 15 13 13 14 16 13 14 15 16 14 15 16 18 17 17 18 20 18 19 20 21 19 20 21 22 21 21 22 24 22 22 23 25 24 24 25 27 25 26 27 28 28 29 30 30 32 35 16 17 18 17 18 19 20 17 18 19 20 19 20 21 22 21 22 23 24 22 23 24 25 23 25 26 27 25 26 27 28 26 27 28 29 28 29 30 31 29 31 31 32 31 32 33 34 33 34 35 36 21 23 22 24 26 23 25 28 33 25 27 30 35 27 29 31 36 28 30 33 37 29 31 34 39 30 32 35 40 32 34 37 42 34 36 39 43 36 38 40 45 45 47 62 48 63 49 64 79 50 65 80 52 67 82 54 69 83 56 70 85 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 150 250 36 37 38 39 38 40 40 42 42 43 44 37 39 42 47 40 42 45 50 43 45 48 52 57 72 87 60 75 90 63 78 92 300 390 45 47 50 55 53 55 58 62 66 70 83 65 80 95 73 88 102 81 96 111 93 108 123 99 113 128 107 122 137 98 150 250 300 390 63 72 81 68 77 86 Table 197 Grade A11 Profile slope tolerance, fHαT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 20 16 14 12 10 0.6 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 50 60 7.5 7.5 8.5 9.5 8.5 10 8.5 9.5 10 9.5 9.5 10 11 11 11 12 12 12 12 13 13 12 13 13 14 13 14 14 15 14 14 15 16 15 15 16 17 16 17 17 18 18 18 19 19 20 22 10 11 11 11 11 12 13 11 12 12 13 12 13 13 14 13 14 15 15 14 15 16 16 15 16 16 17 16 17 17 18 16 17 18 18 18 18 19 20 19 19 20 21 20 21 21 22 21 22 22 23 23 24 24 25 24 25 26 26 27 27 28 14 15 14 15 17 15 16 18 21 16 17 19 22 17 18 20 23 18 19 21 24 19 20 22 24 19 20 22 25 21 22 23 26 22 23 24 27 23 24 26 29 24 25 27 30 26 27 29 32 27 29 30 33 29 30 32 35 34 35 37 39 42 45 53 28 29 39 30 40 31 40 50 32 41 50 33 42 51 34 43 52 35 44 54 36 45 55 38 47 57 40 49 58 41 51 60 46 55 65 51 61 70 59 68 78 99 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 198 Grade A11 Profile form tolerance, ffαT (ten thousandths of an inch, 0.0001 inch) Normal diametral pitch, Pnd 48 40 32 24 Tolerance diameter, dT 0.2 0.4 0.8 10 12 16 20 25 30 40 8.5 10 9.5 10 11 9.5 10 11 12 10 11 11 12 11 12 12 13 13 13 14 15 14 14 15 16 15 15 16 17 16 16 17 18 17 17 18 19 18 19 19 20 19 20 21 22 21 22 23 23 24 27 12 13 14 13 14 15 15 13 14 15 16 14 15 16 17 16 17 18 18 17 18 19 20 18 19 20 21 19 20 21 22 20 21 22 22 21 22 23 24 23 24 24 25 24 25 26 27 25 26 27 28 17 18 17 18 20 18 19 22 25 20 21 23 27 21 22 24 28 22 23 25 29 23 24 26 30 23 25 27 31 25 26 29 32 26 28 30 33 28 29 31 35 35 36 48 37 49 38 50 61 39 51 62 40 52 64 42 53 65 43 55 66 20 16 14 12 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 10 0.6 50 60 98 150 250 28 29 29 30 30 31 31 32 32 33 34 29 30 33 36 31 33 35 38 33 35 37 40 35 37 39 42 41 42 44 48 51 54 64 44 56 68 47 58 70 49 60 72 51 62 74 56 68 80 63 74 86 72 84 95 300 390 76 88 100 83 95 106 Table 199 Grade A11 Helix tolerance, total, FβT (ten thousandths of an inch, 0.0001 inch) Face width, id h b 0.16 0.25 0.5 0.75 1.5 10 15 20 30 39 100 0.2 18 19 21 Tolerance diameter, dT 10 12 16 0.4 18 19 21 23 0.8 19 20 22 23 19 20 22 23 19 20 23 24 20 21 23 25 21 22 24 26 20 25 23 25 26 23 25 27 26 27 24 25 27 29 25 27 29 32 25 28 30 33 26 29 31 34 27 29 31 34 28 30 32 35 28 30 32 36 35 40 36 41 48 37 42 49 56 38 42 49 56 62 30 40 50 60 98 27 28 27 29 30 29 31 33 36 30 32 34 37 30 33 34 38 38 43 50 57 39 43 50 57 40 44 51 58 63 73 63 74 64 74 82 150 31 33 35 38 32 34 36 39 33 36 37 41 37 39 42 40 43 46 40 45 52 59 41 46 53 60 42 46 54 61 43 48 55 62 44 49 56 63 46 50 57 64 49 53 61 68 53 57 64 71 65 75 83 66 76 84 67 77 84 68 78 86 69 79 87 70 80 88 74 84 91 77 87 95 AMERICAN GEAR MANUFACTURERS ASSOCIATION Supplemental Tables for AGMA 2015/915 A02 Table 200 Grade A11 Helix slope tolerance, fHβT (ten thousandths of an inch, 0.0001 inch) Face width, id h b 0.16 0.25 0.5 0.75 0.2 13 14 15 1.5 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited 0.4 13 14 15 16 0.8 13 14 15 17 13 14 16 17 14 15 16 17 15 15 17 18 15 16 17 18 16 18 19 17 18 19 18 19 17 18 19 21 18 19 21 23 18 20 21 23 19 20 22 24 19 21 22 25 20 21 23 25 20 22 23 25 25 29 26 29 34 26 30 35 40 27 30 35 40 45 10 15 20 30 39 Tolerance diameter, dT 10 12 16 20 25 30 40 50 60 98 19 20 19 21 21 20 22 23 26 21 23 24 26 22 23 25 27 27 30 36 41 28 31 36 41 28 31 36 42 45 52 45 52 46 53 59 150 22 24 25 27 23 24 26 28 24 25 27 29 26 27 30 28 30 33 29 32 37 42 29 33 38 43 30 33 38 43 31 34 39 44 32 35 40 45 32 36 41 46 35 38 43 48 37 41 46 51 46 54 59 47 54 60 47 55 60 48 56 61 49 56 62 50 57 63 52 60 65 55 62 68 150 Table 201 Grade A11 Helix form tolerance, ffβT (ten thousandths of an inch, 0.0001 inch) Face width, id h b 0.16 0.25 0.5 0.75 1.5 10 15 20 30 39 0.2 13 14 15 Tolerance diameter, dT 10 12 16 0.4 13 14 15 16 0.8 13 14 15 17 13 14 16 17 14 15 16 17 15 15 17 18 15 16 17 18 20 25 16 18 19 17 18 19 18 19 17 18 19 21 18 19 21 23 18 20 21 23 19 20 22 24 19 21 22 25 20 21 23 25 20 22 23 25 25 29 26 29 34 26 30 35 40 27 30 35 40 45 30 40 50 60 98 19 20 19 21 21 20 22 23 26 21 23 24 26 22 23 25 27 22 24 25 27 23 24 26 28 24 25 27 29 26 27 30 28 30 33 27 30 36 41 28 31 36 41 28 31 36 42 29 32 37 42 29 33 38 43 30 33 38 43 31 34 39 44 32 35 40 45 32 36 41 46 35 38 43 48 37 41 46 51 45 52 45 52 46 53 59 46 54 59 47 54 60 47 55 60 48 56 61 49 56 62 50 57 63 52 60 65 55 62 68 101 PUBLISHED BY AMERICAN GEAR MANUFACTURERS ASSOCIATION 1500 KING STREET, ALEXANDRIA, VIRGINIA 22314 Licensed to Brown & Sharpe Inc./John Horwell ANSI Store order #X134817 Downloaded: 5/25/2004 8:22:38 AM ET Single user license only Copying and networking prohibited ... 10 8.5 9.5 10 8.5 10 11 9.5 10 11 12 11 11 12 13 12 12 13 14 13 14 15 16 15 16 17 10 11 12 13 10 11 12 13 11 11 12 13 11 12 13 14 11 12 13 14 12 13 14 15 14 14 16 17 15 16 17 18 16 17 18 19 17 ... 16 18 15 16 18 19 15 16 18 19 15 16 18 19 11 11 11 11 12 12 12 12 12 12 13 13 13 13 13 14 14 14 14 14 15 15 15 15 15 15 16 17 17 17 17 18 18 18 19 12 12 13 13 14 15 13 14 15 15 14 15 15 16 15 15 ... 9.5 10 11 11 10 10 11 12 10 11 12 12 11 11 12 13 11 12 12 13 10 11 11 12 14 15 11 12 14 16 12 12 14 16 12 13 15 16 12 13 15 17 13 14 16 17 13 14 16 18 17 19 18 19 21 18 19 22 24 18 20 22 24 19