Tài liệu xe HONDA ACCORD - P5

Xe Honda Accord thế hệ thứ 9, bắt đầu từ phiên bản 2013, có sự đổi mới cả về thiết kế nội và ngoại thất, đồng thời ứng dụng nhiều công nghệ mới.

Trang 1

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) (If body maintenance is required)

The Accord SRS includes a driver’s airbag in the steering wheel hub, a passenger’s airbag in the dashboard above theglove box, seat belt tensioners in the front seat belt retractors, seat belt outer lap tensioners in the front seat belt loweranchor, side curtain airbags in the sides of the roof, and side airbags in the front seat-backs Information necessary tosafely service the SRS is included in this Shop Manual Items marked with an asterisk ( ) on the contents pageinclude or are located near SRS components Servicing, disassembling, or replacing these items requires specialprecautions and tools, and should be done by an authorized Honda dealer

• To avoid rendering the SRS inoperative, which could lead to personal injury or death in the event of a severe frontal

or side collision, all SRS service work should be done by an authorized Honda dealer

• Improper service procedures, including incorrect removal and installation of the SRS, could lead to personal injurycaused by unintentional deployment of the airbags, side airbags, and/or side curtain airbags

• Do not bump or impact the SRS unit, front impact sensors, or side impact sensors, or rear safing sensor when theignition switch is ON (II), or for at least 3 minutes after the ignition switch is turned to LOCK (0); otherwise, thesystem may fail in a collision, or the airbags may deploy

• SRS electrical connectors are identified by yellow color coding Related components are located in the steeringcolumn, front console, dashboard, dashboard lower panel, in the dashboard above the glove box, in the front seats,

in the roof side, and around the floor Do not use electrical test equipment on these circuits

Trang 2

Body Doors

Mirrors

Glass

Sunroof

Interior Trim

Consoles

Dashboard

Special Tools 20-2

Component Location Index 20-3 Front Door Panel Removal/Installation 20-12 Front Door Outer Handle Replacement 20-19 Front Door Latch Replacement 20-23 Front Door Glass and Regulator Replacement 20-26 Front Door Sash Inner Trim Replacement 20-29 Front Door Sash Outer Trim Replacement 20-31 Front Door Glass Outer Weatherstrip Replacement 20-31 Front Door Outer Molding Replacement 20-33 Front Door Weatherstrip Replacement 20-34 Rear Door Panel Removal/Installation 20-35 Rear Door Outer Handle Replacement 20-38 Rear Door Latch Replacement 20-40 Rear Door Glass and Regulator Replacement 20-42 Rear Door Sash Inner Trim Replacement 20-45 Rear Door Sash Outer Trim Replacement 20-46 Rear Door Glass Outer Weatherstrip Replacement 20-47 Rear Door Outer Molding Replacement 20-48 Rear Door Weatherstrip Replacement 20-49 Door Glass Adjustment 20-50 Door Position Adjustment 20-51 Door Striker Adjustment 20-53

Component Location Index 20-54 Power Mirror Replacement 20-56 Mirror Holder Replacement 20-57 Mirror Housing Cover Replacement 20-59 Rearview Mirror Replacement 20-59

Component Location Index 20-61 Windshield Replacement 20-63 Rearview Mirror Harness Cover Base Replacement 20-68 Rain Sensor Cover Base Replacement 20-69 Rear Window Replacement 20-70 Quarter Glass Replacement 20-79

Component Location Index 20-84 Symptom Troubleshooting Index 20-85 Glass Position Adjustment 20-86 Glass Replacement 20-86 Glass Weatherstrip Replacement 20-87 Wind Deflector Replacement 20-88 Drain Channel Replacement 20-89 Sunshade Replacement 20-90

Component Location Index 20-98 Trim Removal/Installation - Door Areas 20-101 Trim Removal/Installation - Pillar Areas - Without Side Curtain Airbags 20-105 Trim Removal/Installation - Pillar Areas - With Side Curtain Airbags 20-108 Trim Removal/Installation - Rear Side Area 20-124 Trim Removal/Installation - Rear Shelf Area 20-125 Trim Removal/Installation - Trunk Area 20-128 Trim Removal/Installation - Trunk Lid 20-128 Sunvisor Removal/Installation 20-134 Grab Handle Removal/Installation 20-136 Headliner Removal/Installation 20-138 Carpet Replacement 20-150

Center Console Panel Removal/Installation 20-156 Center Console Removal/Installation 20-158 Center Console Rear Trim Removal/Installation 20-160 Console Armrest Replacement 20-161 Accessory Power Socket Trim Removal/Installation 20-164

Instrument Visor Removal/Installation 20-165 Driver’s Dashboard Lower Cover

Removal/Installation 20-166 Driver’s Pocket Removal/Installation 20-167 Driver’s Dashboard Undercover

Removal/Installation 20-168 Driver’s Outer Dashboard Trim

Removal/Installation 20-168 Driver’s Inner Dashboard Trim

Removal/Installation 20-169 Center Pocket Removal/Installation 20-169 Dashboard Center Lower Cover

Removal/Installation 20-170 Center Display Visor

Removal/Installation 20-172 Passenger’s Dashboard Trim

Removal/Installation 20-172 Glove Box Lock Cylinder Replacement 20-173 Glove Box Removal/Installation 20-174 Glove Box Striker Replacement 20-176 Passenger’s Dashboard Undercover

Removal/Installation 20-176 Dashboard Side Vent

Removal/Installation 20-177 Side Defogger Vent Trim

Removal/Installation 20-178 Driver’s Outer Middle Pad

Removal/Installation 20-178 Driver’s Inner Middle Pad

Removal/Installation 20-179 Passenger’s Middle Pad

Trang 3

Bumpers

Hood

Trunk Lid

Fuel Fill Door

Exterior Trim

Fenderwell

Openers

Frame

Component Location Index 20-191 Front Seat Active Head Restraint Inspection 20-193 Front Seat Removal/Installation 20-194 Front Seat Recline Motor Replacement 20-200 Front Seat Lumbar Support Replacement 20-201 Front Seat Slide Motor Replacement 20-203 Front Seat Slide Lever Replacement 20-206 Front Seat Torsion Bar Replacement 20-207 Rear Seat Access Cable Replacement 20-208 Front Seat Frame Replacement 20-209 Front Seat-back Cover Replacement 20-214 Front Seat Cushion Cover Replacement 20-224 Rear Seat Removal/Installation 20-236 Rear Seat-back Latch Replacement 20-239 Rear Seat-back Release Lever/Cable Removal/Installation 20-240 Rear Seat Armrest Replacement 20-241 Trunk Pass-through Lid Lock Cylinder Replacement 20-242 Trunk Pass-through Lid Replacement 20-243 Rear Seat Armrest Beverage Holder Replacement 20-243 Rear Seat-back Cover Replacement 20-245 Rear Seat Side Bolster Cover Replacement 20-249 Rear Seat Cushion Cover Replacement 20-249

Front Bumper Removal/Installation 20-251 Front Bumper Fog Light Cover Replacement 20-254 Front Air Spoiler Replacement 20-255 Rear Bumper Removal/Installation 20-256 Rear Bumper Finisher Cover Replacement 20-259

Hood Adjustment 20-260 Hood Seal Replacement 20-261 Hood Insulator Replacement 20-262 Hood Support Strut Replacement 20-262

Trunk Lid Adjustment 20-263 Trunk Lid Torsion Bar Replacement 20-264 Trunk Lid Weatherstrip Replacement 20-265 Trunk Lid Cushion Replacement 20-265 Trunk Lid Dynamic Damper Replacement 20-266

Fuel Fill Door Adjustment 20-267 Fuel Cap Adapter Replacement 20-268

Front Grille Cover Replacement 20-269 Front Grille Replacement 20-270 Front Fender Trim Replacement 20-272 Cowl Cover Replacement 20-273 Roof Molding Replacement 20-275 Side Sill Protection Tape Replacement 20-279 Trunk Lower Trim Replacement 20-281 Emblem/Sticker Replacement 20-284

Front Inner Fender Replacement 20-288 Front Splash Shield Replacement 20-289 Front Fender Fairing Replacement 20-290 Middle Floor Undercover Replacement 20-291 Fuel Pipe Protector Replacement 20-292 Rear Inner Fender Replacement 20-292 Rear Air Outlet Replacement 20-293

Component Location Index 20-294 Hood Opener Cable Replacement 20-295 Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Replacement 20-297 Hood Latch Replacement 20-302 Hood Release Handle Replacement 20-303 Trunk Lid Opener/Fuel Fill Door Opener Replacement 20-304 Trunk Lid Latch Replacement 20-305

Frame Brace Replacement 20-307 Rear Wheelhouse Gusset Replacement 20-307 Middle Cross-member Gusset

Replacement 20-308 Subframe Replacement 20-309 Frame Repair Chart 20-312

Trang 4

０１

Special Tools

Trang 5

POWER MIRROR SWITCH

DOOR GLASS INNER WEATHERSTRIP

LOWER GRIP BRACKET

(cont’d)

Removal/Installation, page 20-12

Trang 6

2-door (cont’d)Component Location Index (cont’d)

DOOR SASH INNER TRIM

DOOR SASH OUTER TRIM

DOOR OUTER MOLDING

DOOR GLASS OUTER WEATHERSTRIP

HINGE

DOOR CHECKER

DOOR

DOOR WEATHERSTRIP SPEAKER

Trang 7

20-5

GLASS

IMMOBILIZER and SECURITY LABEL

REGULATOR

CENTER LOWER CHANNEL

OUTER HANDLE COVER

OUTER HANDLE SEALS

OUTER HANDLE BASE

LOCK CYLINDER (Driver’s)

FRONT LOWER CHANNEL GLASS RUN CHANNEL

INNER HANDLE CAP LATCH PROTECTOR

Passenger’s side

OUTER HANDLE HOLDER

Replacement, page 20-26 Adjustment, page 20-50

Replacement, page 20-26

Adjustment, page 20-53

Trang 8

POWER MIRROR SWITCH

DOOR GLASS INNER WEATHERSTRIP

SWITCH PANEL POWER WINDOW SWITCH

COURTESY LIGHT LENS

DOOR PANEL

LHD Passenger’s side

SWITCH PANEL POWER WINDOW SWITCH

RHD Passenger’s side

Removal/Installation, page 20-16

Trang 9

20-7

HINGE

DOOR CHECKER

Trang 10

CENTER LOWER CHANNEL

OUTER HANDLE BASE

LOCK CYLINDER (Driver’s)

STRIKER

INNER HANDLE LATCH CABLE

Trang 12

4-door Rear door (cont’d)Component Location Index (cont’d)

HINGE

DOOR CHECKER

DOOR

DOOR WEATHERSTRIP PLASTIC COVER

Trang 13

20-11

GLASS

REGULATOR

OUTER HANDLE BASE STRIKER

LATCH

INNER HANDLE CABLE

INNER HANDLE CAP

REAR LOWER CHANNEL

OUTER HANDLE HOLDER

CHILD LOCK CAP

QUARTER GLASS

LATCH PROTECTOR

Replacement, page 20-42 Adjustment, page 20-50

Replacement, page 20-38 Replacement, page 20-285

Trang 14

A B

Fastener Locations : Screw, 2

A B : Screw, 1

A

B A

C

Fastener Location : Screw, 1

A

• Take care not to scratch the door and related parts

• When removing components, use the trim tools orequivalent

1 Remove the tweeter cover (see page 20-56)

2 Raise the glass fully

3 Push on the bottom of the inner handle cap (A)while pushing on the upper hook (B) with theappropriate trim tool, then pull back the cap toremove it

4 Remove the screws (A, B) securing the inner handle(C)

5 Remove the front pull pocket cap (A), and removethe screw

6 Pry up the notch (A) of the front door panel cap (B),then pull back the cap to detach the hooks (C), andrelease the hooks (D), then remove the cap

7 Remove the screw, and disconnect the powerwindow switch connector (E) and the power mirrorswitch connector (F)

Trang 15

B C D

A

B C

C

A B

–2 Detach the upper clips

–3 Starting at the rear, pull the door panel upward

NOTE: The inner handle cable (B) and the latchcable (C) are connected to the inner handle (D)

Do not pull the door panel up too far, or thesecables will be damaged

9 While holding the door panel (A) away from thedoor, remove the inner handle (B) from the doorpanel by releasing the hooks (C)

10 Remove the door panel (A) while pulling the innerhandle (B) out through the hole in the door panel

11 Disconnect the inner handle cable (A) and the latchcable (B) from the inner handle (C), then removethe handle

–1 Detach the inner handle cable fasteners (D, E),then disconnect the inner handle cable fromthe cable fasteners

–2 Detach the latch cable fastener (F), and removethe latch cable fastener (G) from the innerhandle by pinching its tabs out

NOTE: Check if the cable fasteners aredamaged or stress-whitened

(cont’d)

Trang 16

Fastener Locations : Screw, 4 : Clip, 3

A B : Scerw, 3 C : Screw, 1

A B

C

D

E F

A

B

12 Remove the ornament panel (A)

–1 Remove the screws from back of the doorpanel (B)

–2 Release the hooks (C) from back of the doorpanel

–3 Detach the hooks (D) and the clips from thegrip base (E)

13 Remove the screws (A, B, C), then remove the gripbase (D) and the upper grip bracket (E) from thedoor panel (F)

Trang 17

A C

A

B C

47 mm (1.85 in.)

A B

14 Remove the switch panel (A) and the armrest (B) as

an assembly from the door panel (C)

–1 Remove the screws from the back of the doorpanel

–2 Pull out along the edge of the armrest torelease all of the hooks (D)

–3 Pull out along the edge of the switch panel torelease the hooks (E) and to detach the clips

15 Remove the screws, and release the hook (A), thenseparate the switch panel (B) and the armrest (C)

16 Install the door panel in the reverse order ofremoval, and note these items:

• If the clips are damaged or stress-whitened,replace them with new ones

• Replace any damaged cable fasteners with newones

• The latch cable (A) should be fixed to the cablefastener (B) with the latch in the unlockedposition as shown

• Make sure the connectors are plugged inproperly, and the cables are connected securely

• Make sure the window and power door lockoperate properly

• When reinstalling the door panel, make sure theplastic cover is installed properly and sealedaround its outside perimeter to seal out water

Trang 18

A B

A

B

A

B

C D

Fastener Locations : Clip, 8 (Gray)

NOTE:

1 Remove the tweeter cover (see page 20-56)

4 Remove the screws securing the inner handle (A)

5 Pry up the notch (A) of the lid (B), then pull back thelid, and remove the screw

6 Remove the door panel (A) with as little bending aspossible to avoid creasing or breaking it

–1 Start at the bottom edge of the door panel,release the clips with a commercially availabletrim pad remover

NOTE: The inner handle cable (B) and the latchcable (C) are connected to the inner handle (D)

Trang 19

A B

C

D E

A

B

C D

C

While holding the door panel away from the door,disconnect the power window switch connector (C),the power mirror switch connector (D), and thecourtesy light bulb socket (E), and detach theharness clip (F)

10 Remove the switch panel (A) from the door panel(B)

–1 Detach the rear clip

–2 Pull out along the edge of the panel to releaseall of the hooks (C)

–3 Pull the switch panel rearward to release thefront hook (D)

(cont’d)

Trang 20

B C

A

B C

D E

C

46.5 mm (1.83 in.)

A B

11 Remove and loosen the screws from back of thedoor panel (A), and release the hook (B), thenremove the armrest (C)

12 Remove the screws from back of the door panel (A),and release the hooks (B, C, D), then remove theornament panel (E)

• Make sure the connectors are plugged inproperly, and the cables are connected securely

Trang 21

NOTE: Put on gloves to protect your hands.

1 Remove the door panel:

• 2-door (see page 20-12)

2 Disconnect the power door lock actuator connector(A), and detach the harness clips (B)

3 Remove the rear plug cap (C), then remove theplastic cover (D) as needed

NOTE: Remove the glue from the door surface Ifthe plastic cover is damaged or torn, replace it

4 Remove the maintenance cap (A) (2-door) or thehole seal (B) (4-door)

(cont’d)

Trang 22

6 x 1.0 mm

8 N·m (0.8 kgf·m, 6 lbf·ft)

B

A

5 Driver’s door: Pull both side flanges (A) of theretainer (B) outward, and pull the middle flangeportion (C) of the outer casing cover (D) out, thendisconnect the cylinder cable (E) from the latch

4-door is shown; 2-door is similar

6 2-door: Pull the glass run channel (A) away asneeded, and remove the bolt, then remove thecenter lower channel (B) by pulling it downward

Trang 23

6 x 1.0 mm 9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)

Fastener Location : Bolt, 1

A B

B

6 x 1.0 mm 9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)

A

B D

8 Release the hooks (A), then remove the lockcylinder (B) (driver’s door) or the outer handleholder (C) (passenger’s door) from the outer handlebase (D)

(cont’d)

Trang 24

9 Driver’s door: If the retainer (A) of the lock cylindercable (B) is damaged, release the hooks (C), thenreplace it.

10 Pull the outer handle (A) back, and out as shown toremove it from the door Take care not to scratchthe door

11 Release the hooks (A, B), then remove the outerhandle front seal (C) and the outer handle rear seal(D)

12 Remove the outer handle base (A)

–1 Detach the rod fastener (B)

–2 With a clip remover, disconnect the outerhandle rod (C)

–3 Loosen the nut

–4 Release the hook (D), and slide the outerhandle base forward to release the special bolt(E) from the door panel

Trang 25

A B

13 Remove the rod fastener (A) from the outer handlebase (B), then replace it with a new one

14 Install the handle in the reverse order of removal,and note these items:

• Reinstall the lock cylinder (driver’s door) or theouter handle holder (passenger’s door) beforeinstalling the outer handle cover

• Make sure that the actuator connector is plugged

in properly, and that the cylinder cable and theouter handle rod are connected securely

• Make sure the door key cylinder/door locksoperate properly

• Make sure the door handle works properly

NOTE: Put on gloves to protect your hands

1 Remove the door panel and the inner handle:

2 Remove the plastic cover as needed (see step 2 onpage 20-19)

3 Detach the rod fastener, and disconnect the outerhandle rod from the outer handle base (see step 12

6 4-door: Pull the glass run channel (A) away asneeded, and remove the bolt, then remove thecenter lower channel (B) by pulling it downward

(cont’d)

Replace.

Trang 26

＊０３

2-door

4-doorFront Door Latch Replacement (cont’d)

6 x 1.0 mm

6 N·m (0.6 kgf·m,

4 lbf·ft)

6 x 1.0 mm

6 N·m (0.6 kgf·m, 4 lbf·ft)

: Screw, 3 B

Fastener Locations

: Screw, 1 C

6 x 1.0 mm

6 N·m (0.6 kgf·m, 4 lbf·ft)

B C : Screw, 1

6 x 1.0 mm

6 N·m (0.6 kgf·m,

E

F

7 Detach the cable clips (A) Remove the screws(B, C) securing the latch (D), then remove the latchthrough the hole in the door Take care not to bendthe outer handle rod (E), the latch cable (F), and theinner handle cable (G)

Trang 27

D

B

A C

9 Disconnect the latch cable (A) and the inner handlecable (B) from the latch (C), and remove the spongeseals (D, E)

10 Install the latch in the reverse order of removal, andnote these items:

• Before reinstalling the cables to the latch (A),clean the latch surface where the new spongeseals will be attached with isopropyl alcohol, andattach the new sponge seals (B, C) to the latch asshown

• After reinstalling the latch cable (D) and the outerhandle cable (E) to the latch, attach the newsponge seal (F) to the cable connecting portions

on the latch as shown

• Before reinstalling the latch protector (G), replacethe inside sponge seal (H) and the outsidesponge seal (I) with new ones:

– Scrape off the old sponge seals from theprotector, and clean the protector surfaces withisopropyl alcohol

– Attach the new inside sponge seal to the insideface of the protector as shown

– After reinstalling the latch protector to the latch,attach the new outside sponge seal to theprotector and the latch as shown

• Make sure that the actuator connector is plugged

in properly, and that the cylinder cable and theouter handle rod are connected securely

• Make sure the door locks and opens properly

Trang 28

B C

G

F E

E

C B

1 Remove the door panel:

2 2-door: Remove the screws, then remove the doorpanel bracket (A)

3 Disconnect the power door lock actuator connector(A), and detach the harness clips (B) Remove theplug caps (C) 4-door: Disconnect the power mirrorconnector (D)

4 Pass the wire harness (E) through the slit (F) in theplastic cover (G), then remove the plastic cover

Trang 29

Fastener Locations : Bolt, 2

6 x 1.0 mm 9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)

A

6 x 1.0 mm 9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)

(cont’d)

Trang 30

C : Bolt, 1

(Silver) D

6 x 1.0 mm 9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)

C : Bolt, 1

(Silver) D

6 x 1.0 mm 9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)

A B E

C D

7 Disconnect the connector (A) from the regulator (B) 9 Apply multipurpose grease to all the sliding

surfaces of the regulator (A) where shown 4-door

is shown; 2-door is similar

10 Install the glass and regulator in the reverse order

of removal, and note these items:

• Roll the glass up and down to see if it movesfreely without binding

• Make sure that there is no clearance between theglass and glass run channel when the glass isclosed

• Adjust the position of the glass as necessary(see page 20-50)

• Do the power window control unit resetprocedure (see page 22-310)

• Check for water leaks (see step 8 on page 20-51)

• Test-drive and check for wind noise and rattles

• Make sure the power door locks, windows andpower mirror operate properly

Trang 31

C D

E

A A

A

D E

B D

F

NOTE: Take care not to scratch the door

1 Remove the door panel (see page 20-12)

2 Lower the glass fully

3 Remove the door sash inner trim (A)

–1 Detach the clip fastening the trim

–2 Pull back along the outside edge of the trim torelease the hook strip (B) from the door glassopening flange at the front pillar portion andthe roof portion of the door sash

–3 Release the hook (C) from the glass runchannel (D) at the rear corner portion of thedoor sash

–4 Pull back along the outside edge of the trim torelease the hook strip (E) from the door glassopening flange at the center pillar portion ofthe door sash

–5 Release the rear hook (F) from the door

4 Install the trim in the reverse order of removal, andnote these items:

• If the clip is damaged or stress-whitened, replace

it with a new one

• Push the hooks and the clip into place securely

Trang 32

B C

D

E

B

A A

D E

B D

Fastener Location : Clip, 1 (Gray)

B D

Fastener Location : Clip, 1 (Gray)

F

NOTE: Take care not to scratch the door

2 Lower the glass fully

3 Remove the front door sash inner trim (A)

–1 Detach the clip fastening the trim

–2 Pull back along the outside edge of the trim torelease the hooks or the hook strip (B) from thedoor glass opening flange at the front pillarportion and the roof portion of the door sash

–3 Release the hook (C) from the glass runchannel (D) at the rear corner portion of thedoor sash

–4 Pull back along the outside edge of the trim torelease the hooks or the hook strip (E) from thedoor glass opening flange at the center pillarportion of the door sash

–5 Release the rear hook (F) from the door

4 Install the trim in the reverse order of removal, andnote these items:

• If the clip is damaged or stress-whitened, replace

it with a new one

• Push the hooks and the clip into place securely

Trang 33

• Take care not to scratch the door

• 4-door is shown; 2-door is similar

1 Remove the door outer molding (see page 20-33)

2 Pull the door sash outer trim (A) up to release thehooks (B) from the door, and release the trim frombetween the door glass outer weatherstrip (C) anddoor, then remove the trim Take care not todamage the door glass outer weatherstrip

3 Install the trim in the reverse order of removal

NOTE:

• Put on gloves to protect your hands

1 Remove these items:

• Door panel– 2-door (see page 20-12)– 4-door (see page 20-16)

• Plastic cover, as needed (see step 2 on page20-26)

• Power mirror (see page 20-56)

3 Remove the screws from the front and rear edges

of the door

(cont’d)

Trang 34

(Engaged position)

A (Released position) D

B

A

B

C A

(Engaged position)

A (Released position) D

C

A

4 From the inside of the door, slide the clips (A) of thedoor glass outer weatherstrip (B) to release thehooks (C) from the flanges (D) of the door panel

5 Pull up the door glass outer weatherstrip (A), thenremove it

6 If the clips are damaged or stress-whitened, replacethem with new ones

7 Before installing the door glass outer weatherstrip,align the clips of the weatherstrip to the flangeswhere the clips should be engaged by sliding them

8 Push the clip portions of the front door glass outerweatherstrip into place securely

Trang 35

• If you remove the door outer molding, replace it with

a new one because it will bend during removal

• 4-door is shown; 2-door is similar

1 Remove the power mirror (see page 20-56)

2 Using a clip remover, detach the clip, then pull backthe door weatherstrip (A), and remove the screw

3 While removing the upper edge of the door outermolding (A) from the edge of the sash, cut thedouble-sided adhesive tape (B) with a utility knife,then remove the molding from the sash, andremove the molding from between the door glassouter weatherstrip (C) and the door

4 Scrape off the remaining double-sided adhesivetape from the sash, then clean the sash surfacewith a sponge dampened in isopropyl alcohol

5 Install the new door outer molding in the reverseorder of removal, and note these items:

• Insert the front edge of the molding between thedoor glass outer weatherstrip and the doorproperly

• Push the adhesive portions into place securely

• Make sure the upper and lower sides of themolding are catching the edges of the sashproperly

• Push the door weatherstrip clip into placesecurely

Trang 36

＊０２

2-door

4-doorFront Door Weatherstrip Replacement

A : Clip, 17

(Left: Pink)

B : Clip, 5

(White) C

(Right: Light Blue)

: Clip, 1 (Black)

D : Clip, 1

(White)

E : Clip, 1

(Orange) F

A B

C D

E F

Fastener Locations : Bolt, 1 A

: Clip, 2 (Black) D

A B

: Clip, 4 (Gray) C

: Clip, 16 (Left: Orange) B

(Right: Purple)

NOTE:

• Take care not to damage the front upper corner clip(black) (4-door) and the rear upper corner clips (black)

in the weatherstrip because these clips are not able toreplace with new ones

• Use a clip remover to remove the clips

1 At the front pillar, remove the door checkermounting bolt (A)

2 Detach the clips (B, C, D, E, F), and release the doorweatherstrip (G) from the holder (H) of the doorsash, then remove the weatherstrip

3 Install the weatherstrip in the reverse order ofremoval, and note these items:

• Make sure the weatherstrip is installed in theholder securely

• Apply medium strength liquid thread lock to thedoor checker mounting bolt before installation

Trang 37

3 Remove the screws securing the inner handle (A)

4 Pry up the notch (A) of the lid (B), then pull back thelid, and remove the screw

5 Remove the door panel (A) with as little bending aspossible to avoid creasing or breaking it

–1 Start at the bottom edge of the door panel,release the clips with a commercially availabletrim pad remover

NOTE: The inner handle cable (B) and latchcable (C) are connected to the inner handle (D)

(cont’d)

Trang 38

A B

A

B

D C

While holding the door panel away from the door,disconnect the power window switch connector (C)

9 Remove the power window switch panel (A) fromthe door panel (B)

–1 Detach the rear clip

–2 Pull out along the edge of the panel to releaseall of the hooks (C)

–3 Pull the switch panel rearward to release thefront hook (D)

Trang 39

B C

A B C

D E

47 mm (1.85 in.)

A B

10 Remove and loosen the screws from back of thedoor panel (A), and release the hook (B), thenremove the armrest assembly (C)

11 Remove the screws from back of the door panel (A),and release the hooks (B, C, D), then remove theornament panel (E)

• Make sure the connector is plugged in properly,and the cables are connected securely

Trang 40

A

6 x 1.0 mm 9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)

A

B C

2 Disconnect the power door lock actuator connector(A), and detach the harness clips (B)

3 Remove the rear plug cap (C), then remove theplastic cover (D) as needed

4 Remove the hole seal (A)

5 While holding the outer handle cover (A) fromoutside of the door, remove the bolt, and thenrelease the hooks (B) of the outer handle cover,then remove the cover

6 Release the hooks (A), then remove the outerhandle holder (B) from the outer handle base (C)

Định dạng
Số trang	317
Dung lượng	10,74 MB