Towards high energy and high power density lithium rich cathode materials for future lithium ion batteries exploring and understanding mechanisms and role of transformation

TOWARDS HIGH-ENERGY AND HIGH-POWER DENSITY LITHIUM-RICH CATHODE MATERIALS FOR FUTURE LITHIUM-ION BATTERIES: EXPLORING AND UNDERSTANDING MECHANISMS AND ROLE OF TRANSFORMATION SONG BOHANG NATIONAL UNIVERSITY OF SINGAPORE 2013 TOWARDS HIGH-ENERGY AND HIGH-POWER DENSITY LITHIUM-RICH CATHODE MATERIALS FOR FUTURE LITHIUM-ION BATTERIES: EXPLORING AND UNDERSTANDING MECHANISMS AND ROLE OF TRANSFORMATION SONG BOHANG (B.Sc.) A THESIS SUBMITTED FOR THE DEGREE OF DOCTOR OF PHILOSOPHY DEPARTMENT OF MECHANICAL ENGINEERING NATIONAL UNIVERSITY OF SINGAPORE 2013 Declaration DECLARATION I hereby declare that the thesis is my original work and it has been written by me in its entirety I have duly acknowledged all the sources of information which have been used in the thesis This thesis has also not been submitted for any degree in any university previously SONG BOHANG 09 August 2013 I Acknowledgements ACKNOWLEDGEMENTS First and foremost, I would like to express my deepest and the most sincere gratitude to my supervisors, Prof Lu Li and A/Prof Lai Man On, for their invaluable guidance and consistent support throughout my four years’ study at the National University of Singapore Their incisive mind and unique perspectives always enlightened me of new insights into research topics, and it is extremely pleasant to work with them I am also grateful to National University of Singapore for the financial support I would like to express my sincere thanks to my seniors, Dr Xiao Pengfei and Dr Wang Hailong for introducing me to this graduate program, teaching and inspiring me a lot in experiments and life I would also like to thank Dr Liu Hongwei and A/Prof Liu Zongwen for their professional skills on transmission electron mircoscopy characterizations In addition, I would like to thank Dr Ye Shukai, Dr Wang Shijie, Dr Zhang Zhen, Dr Xia Hui, Dr Yan Feng, Dr Zhu Jing, Dr Ding Yuanli, Mr Lin Chunfu, Mr Chen Yu, Mr Ding Bo, Mr Yan Binggong and Mr Helmy for their generous encouragement and valuable suggestions on lab work A special appreciation goes to my friend, Mr Mi Yu for the unstoppable support during my four years’ study I would like to acknowledge the following staff in Materials Laboratory: Mr Thomas Tan, Mr Ng Hongwei, Mr Khalim, Mr Juraimi and Dr Aye Thein for providing professional technical support Finally, I would like to express my utmost thanks to my parents and all other family members Without their understandings and endless love, I wouldn’t make it happen to accomplish this entire study II Summary SUMMARY Developing high-energy and high-power density cathode materials for next-generation lithium ion batteries (LIB) is important and urgent because of high demand of long lasting power sources, such as portable devices, power tools and electric vehicles (EVs) In addition to the cathode materials developed in the past two decades, a new family of Li-rich layered cathodes has received great interests due to their high theoretical and reversible capacities However, several drawbacks still gap them from real applications, for instance first irreversible capacity loss, poor rate capability and voltage decay during electrochemical cycling To conquer these critical issues, this study firstly focuses on exploring the mechanisms behind the voltage decay which is highly associated with inevitable phase transformation in local structure To solve this issue, a doping strategy taking advantages of cation ions is proposed to slow down the progress of this phase transformation Furthermore, inspired by a positive aspect on rate performance as a result of serious transformation, several surface modification strategies are proposed to enhance the rate capability of the Li-rich layered cathode, which involves a similar phase transformation during preparation but only occurs in the particle surface regions Systematic characterizations on crystal structure and solid state chemistry are performed to lead to comprehensive understandings on various evolutions of corresponding electrochemical behaviors III Table of Contents Table of Contents DECLARATION I ACKNOWLEDGEMENTS II SUMMARY III LIST OF FIGURES IX LIST OF TABLES XXII CHAPTER INTRODUCTION AND LITERATURE REVIEW 1.1 Basic Concepts of Rechargeable Li-ion Batteries 1.2 Literature Review 1.2.1 Overview of Electrode Materials 1.2.2 Cathode Materials Within Spinel Structure 1.2.3 Cathode Materials Within Olivine Structure 1.2.4 Cathode Materials Within Layered Structure 11 1.2.4.1 Conventional LiCoO2, LiNiO2 and LiMnO2 11 1.2.4.2 Other Derivatives 13 1.2.5 Cathode Materials Within Two-phase Integrated Structure 19 1.2.5.1 Origins of Designation and Basic Concepts 19 1.2.5.2 Critical Issues and Achieved Improvements 22 1.3 Present Work on Improving Li-rich Layered Cathodes 26 CHAPTER EXPERIMENTAL APPROACH 28 2.1 Synthesis Routes 28 IV Table of Contents 2.1.1 Hydroxide Based Co-precipitation Method 28 2.1.2 Spray-dryer Assisted Sol-gel Method 29 2.2 Material Characterizations 29 2.2.1 Elemental Analysis 29 2.2.2 X-ray Diffraction and Rietveld Refinement 30 2.2.3 Raman Spectroscopy 30 2.2.4 Electron Microscopy 30 2.2.5 X-ray Photoelectron Spectroscopy 31 2.2.6 TGA/DSC Characterization 31 2.3 Characterization of Electrochemical Properties 31 2.3.1 Preparation of Positive Electrode and Battery Assembly 31 2.3.2 Galvanostatic Charge/Discharge Cycling 32 2.3.3 Cyclic Voltammetry 33 2.3.4 Electrochemical Impedance Spectroscopy 33 2.3.5 dQ/dV Plots 33 CHAPTER Ru DOPING ON 3a SITE IN Li-RICH LAYERED CATHODES 35 3.1 Motivation of the Doping Strategy 35 3.2 Material Preparation 36 3.3 Crystallographic Characterizations 37 3.4 Electrochemical Properties 41 3.5 Discussions on Facile Phase Transformation upon Long-term Cycling 56 3.5.1 Analysis Based on Electrochemical Behaviors 56 V Table of Contents 3.5.2 XPS analysis 59 3.5.3 Analysis Based on TEM-EDS and ICP 62 3.5.4 Analysis based on HRTEM 64 3.5.5 Analysis Based on Ex-situ XRD 69 3.5.6 Influence of Spinel-like Phase on Electrochemical Performance 70 3.6 Summary 72 CHAPTER Cr DOPING ON 3a SITE IN Li-RICH LAYERED CATHODES .74 4.1 Motivation of the Doping Strategy 74 4.2 Material Preparation 75 4.3 Crystallographic Characterization 76 4.4 Electrochemical Properties 82 4.5 Suppression of Phase Transformation upon Long-term Cycling 86 4.5.1 XPS Analysis 86 4.5.2 Cycle Performance 90 4.5.3 Analysis Based on Discharge Curves and dQ/dV 93 4.5.4 Ex-situ XRD 97 4.6 Summary 98 CHAPTER GRAPHENE-INVOLVED SURFACE TREATMENT ON LI-RICH LAYERED CATHODES 100 5.1 Motivation of the Modification Strategy 100 5.2 Material Preparation 101 5.3 Crystallographic Characterization 102 5.4 Electrochemical Properties 112 VI Table of Contents 5.4.1 Galvanostatic Charge/Discharge Behaviors 112 5.4.2 Cyclic Voltammetry 115 5.5 Discussions on Enhanced Rate Capability Led by Phase Transformation 117 5.5.1 XPS Analysis 118 5.5.2 Cycling Performance and Enhanced Rate Capability 121 5.5.3 Analysis Based on Discharge Curves and dQ/dV 125 5.5.4 Analysis Based on EIS 128 5.6 Summary 130 CHAPTER CARBON BLACK-INVOLVED SURFACE TREATMENT ON LI-RICH LAYERED CATHODES 131 6.1 Motivation of the Modification Strategy 131 6.2 Material Preparation 132 6.3 Crystallographic Characterizations 132 6.4 Electrochemical Properties 139 6.4.1 Galvanostatic Charge/Discharge Behaviors 139 6.4.2 Cyclic Voltammetry 141 6.5 Discussion on Enhanced Rate Capability Led by Phase Transformation 144 6.5.1 XPS Analysis 144 6.5.2 Analysis Based on TEM-EDS 146 6.5.3 Cycling Performance and Enhanced Rate Capability 148 6.5.4 Analysis Based on Discharge Curves and dQ/dV 151 6.5.5 Analysis Based on EIS 153 VII Table of Contents 6.6 Summary 155 CHAPTER SURFACE COATING OF CARBON ON LI-RICH LAYERED CATHODES 157 7.1 Motivation of the Modification Strategy 157 7.2 Material Preparation 157 7.3 Crystallographic Characterizations 158 7.4 Electrochemical Properties 166 7.5 Discussion on Enhanced Cyclability and Rate Capability 169 7.5.1 XPS Analysis 169 7.5.2 Enhanced Cyclability and Rate Capability 172 7.5.3 Analysis Based on Discharge Curves and dQ/dV 173 7.6 Summary 176 CHAPTER CONCLUSIONS AND RECOMMENDATIONS 177 8.1 Conclusions 177 8.2 Limitations and Recommendations 181 REFERENCES 184 LIST OF PUBLICATIONS 197 VIII References REFERENCES Tarascon, J.M and M Armand, Issues and challenges facing rechargeable lithium batteries Nature, 2001 414(6861): p 359-367 Armand, M and J.M Tarascon, Building better batteries Nature, 2008 451(7179): p 652-657 Goodenough, J.B and Y Kim, Challenges for Rechargeable Li Batteries Chemistry of Materials, 2010 22(3): p 587-603 Whittingham, M.S., Materials challenges facing electrical energy storage Mrs Bulletin, 2008 33(4): p 411-419 Gamble, F.R., et al., INTERCALATION COMPLEXES OF LEWIS BASES AND LAYERED SULFIDES LARGE CLASS OF NEW SUPERCONDUCTORS Science, 1971 174(4008): p 493-& Whittingham, M.S., ELECTRICAL ENERGY-STORAGE AND INTERCALATION CHEMISTRY Science, 1976 192(4244): p 1126-1127 Murphy, D.W., et al., VANADIUM-OXIDE CATHODE MATERIALS FOR SECONDARY LITHIUM CELLS Journal of the Electrochemical Society, 1979 126(3): p 497-499 Whittingham, M.S and M.B Dines, NORMAL-BUTYLLITHIUM - EFFECTIVE, GENERAL CATHODE SCREENING AGENT Journal of the Electrochemical Society, 1977 124(9): p 1387-1388 Whittingham, M.S., ROLE OF TERNARY PHASES IN CATHODE REACTIONS Journal of the Electrochemical Society, 1976 123(3): p 315-320 10 Mizushima, K., et al., LIXCOO2 "(OLESS-THANXLESS-THAN-OR-EQUAL-TO1) - A NEW CATHODE MATERIAL FOR BATTERIES OF HIGH-ENERGY DENSITY Materials Research Bulletin, 1980 15(6): p 783-789 11 Fong, R., U Vonsacken, and J.R Dahn, STUDIES OF LITHIUM INTERCALATION INTO CARBONS USING NONAQUEOUS ELECTROCHEMICAL-CELLS Journal of the Electrochemical Society, 1990 137(7): p 2009-2013 12 Yazami, R., Surface chemistry and lithium storage capability of the graphite-lithium electrode Electrochimica Acta, 1999 45(1-2): p 87-97 13 Whittingham, M.S., Lithium batteries and cathode materials Chemical Reviews, 2004 104(10): p 4271-4301 14 Ellis, B.L., K.T Lee, and L.F Nazar, Positive Electrode Materials for Li-Ion and Li-Batteries Chemistry of Materials, 2010 22(3): p 691-714 15 Thackeray, M.M., et al., LITHIUM INSERTION INTO MANGANESE SPINELS Materials Research Bulletin, 1983 18(4): p 461-472 16 Robertson, A.D., et al., M3+-modified LiMn2O4 spinel intercalation cathodes Admetal effects on morphology and electrochemical performance Journal of the Electrochemical Society, 1997 144(10): p 3500-3505 17 Jang, D.H., Y.J Shin, and S.M Oh, Dissolution of spinel oxides and capacity losses in 4V Li/LixMn2O4 coils Journal of the Electrochemical Society, 1996 143(7): p 2204-2211 18 Tarascon, J.M., et al., SYNTHESIS CONDITIONS AND OXYGEN STOICHIOMETRY EFFECTS ON LI INSERTION INTO THE SPINEL LIMN2O4 Journal of the Electrochemical Society, 1994 141(6): 184 References p 1421-1431 19 Kunduraci, M and G.G Amatucci, Synthesis and characterization of nanostructured 4.7 VLixMn1.5Ni0.5O4 spinels for high-power lithium-ion batteries Journal of the Electrochemical Society, 2006 153(7): p A1345-A1352 20 Kunduraci, M., J.F Al-Sharab, and G.G Amatucci, High-power nanostructured LiMn2-xNixO4 high-voltage lithium-ion battery electrode materials: Electrochemical impact of electronic conductivity and morphology Chemistry of Materials, 2006 18(15): p 3585-3592 21 Tarascon, J.M., et al., THE SPINEL PHASE OF LIMN2O4 AS A CATHODE IN SECONDARY LITHIUM CELLS Journal of the Electrochemical Society, 1991 138(10): p 2859-2864 22 Okada, M., Y.S Lee, and M Yoshio, Cycle characterizations of LiMxMn2-xO4 (M = Co, Ni) materials for lithium secondary battery at wide voltage region Journal of Power Sources, 2000 90(2): p 196-200 23 Lee, Y.S., N Kumada, and M Yoshio, Synthesis and characterization of lithium aluminum-doped spinel (LiAlxMn2-xO4) for lithium secondary battery Journal of Power Sources, 2001 96(2): p 376-384 24 Kim, D.K., et al., Spinel LiMn2O4 Nanorods as Lithium Ion Battery Cathodes Nano Letters, 2008 8(11): p 3948-3952 25 Lee, H.W., et al., Ultrathin Spinel LiMn2O4 Nanowires as High Power Cathode Materials for Li-Ion Batteries Nano Letters, 2010 10(10): p 3852-3856 26 Jiao, F., et al., Synthesis of Ordered Mesoporous Li-Mn-O Spinel as a Positive Electrode for Rechargeable Lithium Batteries Angewandte Chemie-International Edition, 2008 47(50): p 9711-9716 27 Ohzuku, T and R.J Brodd, An overview of positive-electrode materials for advanced lithium-ion batteries Journal of Power Sources, 2007 174(2): p 449-456 28 Padhi, A.K., K.S Nanjundaswamy, positive-electrode materials for and J.B Goodenough, Phospho-olivines rechargeable lithium batteries Journal of as the Electrochemical Society, 1997 144(4): p 1188-1194 29 Yamada, A., S.C Chung, and K Hinokuma, Optimized LiFePO4 for lithium battery cathodes Journal of the Electrochemical Society, 2001 148(3): p A224-A229 30 Yang, S.F., et al., Reactivity, stability and electrochemical behavior of lithium iron phosphates Electrochemistry Communications, 2002 4(3): p 239-244 31 Herle, P.S., et al., Nano-network electronic conduction in iron and nickel olivine phosphates Nature Materials, 2004 3(3): p 147-152 32 Huang, H., S.C Yin, and L.F Nazar, Approaching theoretical capacity of LiFePO4 at room temperature at high rates Electrochemical and Solid State Letters, 2001 4(10): p A170-A172 33 Yang, S.F., et al., Performance of LiFePO4 as lithium battery cathode and comparison with manganese and vanadium oxides Journal of Power Sources, 2003 119: p 239-246 34 Chung, S.Y., J.T Bloking, and Y.M Chiang, Electronically conductive phospho-olivines as lithium storage electrodes Nature Materials, 2002 1(2): p 123-128 35 Kang, B and G Ceder, Battery materials for ultrafast charging and discharging Nature, 2009 458(7235): p 190-193 36 Delacourt, C., et al., One-step low-temperature route for the preparation of electrochemically active LiMnPO4 powders Chemistry of Materials, 2004 16(1): p 93-99 185 References 37 Amine, K., H Yasuda, and M Yamachi, Olivine LiCoPO4 as 4.8 V electrode material for lithium batteries Electrochemical and Solid State Letters, 2000 3(4): p 178-179 38 Barker, J., M.Y Saidi, and J.L Swoyer, Electrochemical insertion properties of the novel lithium vanadium fluorophosphate, LiVPO4F Journal of the Electrochemical Society, 2003 150(10): p A1394-A1398 39 Pizarrosanz, J.L., et al., THE NATURAL AND SYNTHETIC TAVORITE MINERALS CRYSTAL-CHEMISTRY AND MAGNETIC-PROPERTIES Materials Letters, 1994 18(5-6): p 327-330 40 Barker, J., et al., Structural and electrochemical properties of lithium vanadium fluorophosphate, LiVPO4F Journal of Power Sources, 2005 146(1-2): p 516-520 41 Nyten, A., et al., Electrochemical performance of Li2FeSiO4 as a new Li-battery cathode material Electrochemistry Communications, 2005 7(2): p 156-160 42 Dominko, R., et al., Structure and electrochemical performance of Li2MnSiO4 and Li2FeSiO4 as potential Li-battery cathode materials Electrochemistry Communications, 2006 8(2): p 217-222 43 Van der Ven, A., et al., First-principles investigation of phase stability in LixCoO2 Physical Review B, 1998 58(6): p 2975-2987 44 Amatucci, G.G., J.M Tarascon, and L.C Klein, CoO2, the end member of the LixCoO2 solid solution Journal of the Electrochemical Society, 1996 143(3): p 1114-1123 45 Bruce, P.G., A.R Armstrong, and R.L Gitzendanner, New intercalation compounds for lithium batteries: layered LiMnO2 Journal of Materials Chemistry, 1999 9(1): p 193-198 46 Robertson, A.D., A.R Armstrong, and P.G Bruce, Layered LixMn1-yCoyO2 intercalation electrodes-influence of ion exchange on capacity and structure upon cycling Chemistry of Materials, 2001 13(7): p 2380-2386 47 Armstrong, A.R and P.G Bruce, Synthesis of layered LiMnO2 as an electrode for rechargeable lithium batteries Nature, 1996 381(6582): p 499-500 48 Bruce, P.G., B Scrosati, and J.M Tarascon, Nanomaterials for rechargeable lithium batteries Angewandte Chemie-International Edition, 2008 47(16): p 2930-2946 49 Ohzuku, T and Y Makimura, Layered lithium insertion material of LiNi1/2Mn1/2O2: A possible alternative to LiCoO2 for advanced lithium-ion batteries Chemistry Letters, 2001(8): p 744-745 50 Kang, K.S., et al., Electrodes with high power and high capacity for rechargeable lithium batteries Science, 2006 311(5763): p 977-980 51 Yoon, W.S., et al., Investigation of the local structure of the LiNi0.5Mn0.5O2 cathode material during electrochemical cycling by X-ray absorption and NMR spectroscopy Electrochemical and Solid State Letters, 2002 5(11): p A263-A266 52 Yoon, W.S., et al., In situ X-ray absorption spectroscopic study on LiNi0.5Mn0.5O2 cathode material during electrochemical cycling Chemistry of Materials, 2003 15(16): p 3161-3169 53 Reed, J and G Ceder, Charge, potential, and phase stability of layered Li(Ni0.5Mn0.5)O-2 Electrochemical and Solid State Letters, 2002 5(7): p A145-A148 54 Delmas, C., et al., On the behavior of the LixNiO2 system: an electrochemical and structural overview Journal of Power Sources, 1997 68(1): p 120-125 55 Jang, Y.I., et al., Electrochemical cycling-induced spinel formation in high-charge-capacity orthorhombic LiMnO2 Journal of the Electrochemical Society, 1999 146(9): p 3217-3223 186 References 56 Schougaard, S.B., et al., LiNi0.5+delta Mn0.5-delta O2 - A high-rate, high-capacity cathode for lithium rechargeable batteries Advanced Materials, 2006 18(7): p 905-909 57 Makimura, Y and T Ohzuku, Lithium insertion material of LiNi1/2Mn1/2O2 for advanced lithium-ion batteries Journal of Power Sources, 2003 119: p 156-160 58 Ohzuku, T and Y Makimura, Layered lithium insertion material of LiCo1/3Ni1/3Mn1/3O2 for lithium-ion batteries Chemistry Letters, 2001(7): p 642-643 59 Koyama, Y., et al., Systematic research on insertion materials based on superlattice models in a phase triangle of LiCoO2-LiNiO2-LiMnO2 I First-principles calculation on electronic and crystal structures, phase stability and new LiNi1/2Mn1/2O2 material Journal of the Electrochemical Society, 2004 151(9): p A1499-A1506 60 Thackeray, M.M., et al., Li2MnO3-stabilized LiMO2 (M = Mn, Ni, Co) electrodes for lithium-ion batteries Journal of Materials Chemistry, 2007 17(30): p 3112-3125 61 Hwang, B.J., et al., A combined computational/experimental study on LiNi1/3Co1/3Mn1/3O2 Chemistry of Materials, 2003 15(19): p 3676-3682 62 Koyama, Y., et al., Solid-state chemistry, and electrochemistry of LiCo1/3Ni1/3Mn1/3O2 for advanced lithium-ion batteries - I First-principles calculation on the crystal and electronic structures Journal of the Electrochemical Society, 2004 151(10): p A1545-A1551 63 Yabuuchi, N., Y Makimura, and T Ohzuku, Solid-state chemistry and electrochemistry of LiCo1/3Ni1/3Mn1/3O2 for advanced lithium-ion batteries III Rechargeable capacity and cycleability Journal of the Electrochemical Society, 2007 154(4): p A314-A321 64 Shaju, K.M and P.G Bruce, Macroporous Li(Ni1/3Co1/3Mn1/3)O-2: A high-power and high-energy cathode for rechargeable lithium batteries Advanced Materials, 2006 18(17): p 2330-+ 65 Yabuuchi, N., et al., Solid-state chemistry and electrochemistry of LiCo1/3Ni1/3Mn1/3O2 for advanced lithium-ion batteries Journal of the Electrochemical Society, 2005 152(7): p A1434-A1440 66 Park, S.H., et al., Synthesis of nanostructured Li Ni1/3Co1/3Mn1/3 O-2 via a modified carbonate process Chemistry of Materials, 2005 17(1): p 6-8 67 Shaju, K.M., G.V.S Rao, and B.V.R Chowdari, Performance of layered Li(Ni1/3Co1/3Mn1/3)O-2 as cathode for Li-ion batteries Electrochimica Acta, 2002 48(2): p 145-151 68 Lin, B., et al., Morphology and electrochemical performance of Li Ni1/3Co1/3Mn1/3 O-2 cathode material by a slurry spray drying method Journal of Power Sources, 2008 175(1): p 564-569 69 Park, S.H., et al., Synthesis and structural characterization of layered Li Ni1/3Co1/3Mn1/3 O-2 cathode materials by ultrasonic spray pyrolysis method Electrochimica Acta, 2004 49(4): p 557-563 70 Myung, S.T., K Amine, and Y.K Sun, Surface modification of cathode materials from nano- to microscale for rechargeable lithium-ion batteries Journal of Materials Chemistry, 2010 20(34): p 7074-7095 71 Marcinek, M.L., et al., Microwave Plasma Chemical Vapor Deposition of Carbon Coatings on LiNi1/3Co1/3Mn1/3O2 for Li-Ion Battery Composite Cathodes Journal of the Electrochemical Society, 2009 156(1): p A48-A51 72 Kim, H.S., et al., Effect of carbon coating on LiNi1/3Mn1/3Co1/3O2 cathode material for 187 References lithium secondary batteries Journal of Power Sources, 2007 171(2): p 917-921 73 Lin, B., et al., Electrochemical properties of carbon-coated Li Ni1/3Co1/3Mn1/3 O-2 cathode material for lithium-ion batteries Solid State Ionics, 2008 179(27-32): p 1750-1753 74 Sun, Y.K., et al., AlF3-coating to improve high voltage cycling performance of Li Ni1/3Co1/3Mn1/3 O-2 cathode materials for lithium secondary batteries Journal of the Electrochemical Society, 2007 154(3): p A168-A172 75 Huang, Y.Y., et al., A modified ZrO2-coating process to improve electrochemical performance of Li(Ni1/3Co1/3Mn1/3)O-2 Journal of Power Sources, 2009 188(2): p 538-545 76 Hu, S.K., et al., Cycle life improvement of ZrO2-coated spherical LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion batteries Journal of Power Sources, 2009 188(2): p 564-569 77 Jang, S.B., et al., Synthesis and improved electrochemical performance of Al (OH)(3)-coated Li Ni1/3Mn1/3Co1/3 O-2 cathode materials at elevated temperature Electrochimica Acta, 2005 50(20): p 4168-4173 78 Myung, S.T., et al., Role of alumina coating on Li-Ni-Co-Mn-O particles as positive electrode material for lithium-ion batteries Chemistry of Materials, 2005 17(14): p 3695-3704 79 Kim, Y., H.S Kim, and S.W Martin, Synthesis and electrochemical characteristics of Al2O3-coated LiNi1/3Co1/3Mn1/3O2 cathode materials for lithium ion batteries Electrochimica Acta, 2006 52(3): p 1316-1322 80 Sun, Y.K., et al., High-energy cathode material for long-life and safe lithium batteries Nature Materials, 2009 8(4): p 320-324 81 Jung, Y.S., et al., Ultrathin Direct Atomic Layer Deposition on Composite Electrodes for Highly Durable and Safe Li-Ion Batteries Advanced Materials, 2010 22(19): p 2172-2176 82 Johnson, C.S., et al., Anomalous capacity and cycling stability of xLi(2)MnO(3)center dot(1-x)LiMO2 electrodes (M = Mn, Ni, Co) in lithium batteries at 50 degrees C Electrochemistry Communications, 2007 9(4): p 787-795 83 Robertson, A.D and P.G Bruce, Mechanism of electrochemical activity in Li2MnO3 Chemistry of Materials, 2003 15(10): p 1984-1992 84 Deng, H.X., et al., Nanostructured Lithium Nickel Manganese Oxides for Lithium-Ion Batteries Journal of the Electrochemical Society, 2010 157(4): p A447-A452 85 Lu, Z.H., D.D MacNeil, and J.R Dahn, Layered cathode materials Li NixLi(1/3-2x/3)Mn(2/3-x/3) O-2 for lithium-ion batteries Electrochemical and Solid State Letters, 2001 4(11): p A191-A194 86 Armstrong, A.R., et al., Demonstrating oxygen loss and associated structural reorganization in the lithium battery cathode Li Ni0.2Li0.2Mn0.6 O-2 Journal of the American Chemical Society, 2006 128(26): p 8694-8698 87 Grey, C.P., et al., Electrochemical activity of Li in the transition-metal sites of O3Li Li(1-2x)/3Mn(2-x)/3Nix O-2 Electrochemical and Solid State Letters, 2004 7(9): p A290-A293 88 Kang, K and G Ceder, Factors that affect Li mobility in layered lithium transition metal oxides Physical Review B, 2006 74(9) 89 Gu, M., et al., Formation of the Spinel Phase in the Layered Composite Cathode Used in Li-Ion Batteries Acs Nano, 2013 7(1): p 760-767 90 Yabuuchi, N., et al., Detailed Studies of a High-Capacity Electrode Material for Rechargeable 188 References Batteries, Li2MnO3-LiCo1/3Ni1/3Mn1/3O2 Journal of the American Chemical Society, 2011 133(12): p 4404-4419 91 Hong, J., et al., Critical Role of Oxygen Evolved from Layered Li-Excess Metal Oxides in Lithium Rechargeable Batteries Chemistry of Materials, 2012 24(14): p 2692-2697 92 Song, B.H., M.O Lai, and L Lu, Influence of Ru substitution on Li-rich 0.55Li(2)MnO(3)center dot 0.45LiNi(1/3)Co(1/3)Mn(1/3)O(2) cathode for Li-ion batteries Electrochimica Acta, 2012 80: p 187-195 93 Wang, Q.Y., et al., High capacity double-layer surface modified Li Li0.2Mn0.54Ni0.13Co0.13 O-2 cathode with improved rate capability Journal of Materials Chemistry, 2009 19(28): p 4965-4972 94 Liu, J., B Reeja-Jayan, and A Manthiram, Conductive Surface Modification with Aluminum of High Capacity Layered Li Li0.2Mn0.54Ni0.13Co0.13 O-2 Cathodes Journal of Physical Chemistry C, 2010 114(20): p 9528-9533 95 Xu, B., et al., Identifying surface structural changes in layered Li-excess nickel manganese oxides in high voltage lithium ion batteries: A joint experimental and theoretical study Energy & Environmental Science, 2011 4(6): p 2223-2233 96 Amalraj, F., et al., Study of the Lithium-Rich Integrated Compound xLi(2)MnO(3) center dot (1-x)LiMO2 (x around 0.5; M = Mn, Ni, Co; 2:2:1) and Its Electrochemical Activity as Positive Electrode in Lithium Cells Journal of the Electrochemical Society, 2013 160(2): p A324-A337 97 Song, B.H., et al., Structural evolution and the capacity fade mechanism upon long-term cycling in Li-rich cathode material Physical Chemistry Chemical Physics, 2012 14(37): p 12875-12883 98 Croy, J.R., et al., Li2MnO3-based composite cathodes for lithium batteries: A novel synthesis approach and new structures Electrochemistry Communications, 2011 13(10): p 1063-1066 99 Croy, J.R., et al., Countering the Voltage Decay in High Capacity xLi(2)MnO(3)center dot(1-x)LiMO2 Electrodes (M=Mn, Ni, Co) for Li+-Ion Batteries Journal of the Electrochemical Society, 2012 159(6): p A781-A790 100 Gu, M., et al., Conflicting Roles of Nickel in Controlling Cathode Performance in Lithium Ion Batteries Nano Letters, 2012 12(10): p 5186-5191 101 Croy, J.R., et al., Designing High-Capacity, Lithium-Ion Cathodes Using X-ray Absorption Spectroscopy Chemistry of Materials, 2011 23(24): p 5415-5424 102 Kang, S.H and M.M Thackeray, Enhancing the rate capability of high capacity xLi(2)MnO(3) center dot (1-x)LiMO2 (M = Mn, Ni, Co) electrodes by Li-Ni-PO4 treatment Electrochemistry Communications, 2009 11(4): p 748-751 103 Wu, F., et al., Can surface modification be more effective to enhance the electrochemical performance of lithium rich materials? Journal of Materials Chemistry, 2012 22(4): p 1489-1497 104 Liu, Y.J., et al., Effect of MnO2 modification on electrochemical performance of LiNi0.2Li0.2Mn0.6O2 layered solid solution cathode Journal of Power Sources, 2013 222: p 455-460 105 Yu, D.Y.W., K Yanagida, and H Nakamura, Surface Modification of Li-Excess Mn-based Cathode Materials Journal of the Electrochemical Society, 2010 157(11): p A1177-A1182 189 References 106 Amine, K., et al., Mechanism of capacity fade of MCMB/Li-1.1 Ni1/3Mn1/3Co1/3 (0.9)O-2 cell at elevated temperature and additives to improve its cycle life Journal of Materials Chemistry, 2011 21(44): p 17754-17759 107 Ito, A., et al., Cyclic deterioration and its improvement for Li-rich layered cathode material Li Ni0.17Li0.2Co0.07Mn0.56 O-2 Journal of Power Sources, 2010 195(2): p 567-573 108 Jung, Y.S., et al., Effects of Atomic Layer Deposition of Al2O3 on the Li Li0.20Mn0.54Ni0.13Co0.13 O-2 Cathode for Lithium-Ion Batteries Journal of the Electrochemical Society, 2011 158(12): p A1298-A1302 109 Singh, G., et al., Electrochemical and Structural Investigations on ZnO Treated 0.5 Li2MnO3-0.5LiMn(0.5)Ni(0.5)O(2) Layered Composite Cathode Material for Lithium Ion Battery Journal of the Electrochemical Society, 2012 159(4): p A470-A478 110 Zhang, H.Z., et al., Surface nitridation of Li-rich layered Li(Li0.17Ni0.25Mn0.58)O-2 oxide as cathode material for lithium-ion battery Journal of Materials Chemistry, 2012 22(26): p 13104-13109 111 Wang, Q.Y., et al., High capacity double-layer surface modified Li Li(0.2)Mn(0.54)Ni(0.13)Co(0.13) O(2) cathode with improved rate capability Journal of Materials Chemistry, 2009 19(28): p 4965-4972 112 Larson, A.C and R.B VonDreele, Los Alamos National Laboratory Report LAUR 2000: p 86-748 113 Liu, J and A Manthiram, Understanding the Improved Electrochemical Performances of Fe-Substituted V Spinel Cathode LiMn1.5Ni0.5O4 Journal of Physical Chemistry C, 2009 113(33): p 15073-15079 114 Marzec, J., et al., Conduction mechanism in operating a LiMn2O4 cathode Solid State Ionics, 2002 146(3-4): p 225-237 115 Wilcox, J., S Patoux, and M Doeff, Structure and Electrochemistry of LiNi1/3Co1/3-yMyMn1/3O2 (M = Ti, Al, Fe) Positive Electrode Materials Journal of the Electrochemical Society, 2009 156(3): p A192-A198 116 Zhou, F., X.M Zhao, and J.R Dahn, Synthesis, Electrochemical Properties, and Thermal Stability of Al-Doped LiNi1/3Mn1/3Co(1/3-z)AlzO2 Positive Electrode Materials Journal of the Electrochemical Society, 2009 156(4): p A343-A347 117 Hong, J., et al., Structural evolution of layered Li1.2Ni0.2Mn0.6O2 upon electrochemical cycling in a Li rechargeable battery Journal of Materials Chemistry, 2010 20(45): p 10179-10186 118 Johnson, C.S., et al., Synthesis, Characterization and Electrochemistry of Lithium Battery Electrodes: xLi(2)MnO(3)center dot(1-x)LiMn0.333Ni0.333Co0.333O2 (0