Mechanical Properties CRC Handbook of Materials Science & Engineering Nimonic 75, bar 21 750 540 635 650 538 760 290 870 145 Nimonic 80A, bar 21 1240 540 1100 650 1000 760 760 870 400 Nimonic 90, bar 21 1240 540 1100 650 1030 760 825 870 430 Nimonic 105, bar 21 1140 540 1100 650 1080 760 965 870 605 Nimonic 115, bar 21 1240 540 1090 650 1120 760 1080 870 825 Pyromet 860, bar 21 1300 540 1250 650 1110 760 910 Table 141. TENSILE STRENGTH OF N ICKEL-BASE SUPERALLOYS (SHEET 3 OF 5) Alloy Temperature (°C) Tensile Strength (MPa) Data from ASM Metals Reference Book, Third Edition, Michael Bauccio, Ed., ASM International, Materials Park, OH, p387-389, (1993). 8.03 Mechanical Page 576 Wednesday, December 31, 1969 17:00 ©2001 CRC Press LLC Shackelford & Alexander Mechanical Properties René 41, bar 21 1420 540 1400 650 1340 760 1100 870 620 René 95, bar 21 1620 540 1540 650 1460 760 1170 Udimet 500, bar 21 1310 540 1240 650 1210 760 1040 870 640 Udimet 520, bar 21 1310 540 1240 650 1170 760 725 870 515 Udimet 700, bar 21 1410 540 1280 650 1240 760 1030 870 690 Udimet 710, bar 21 1190 540 1150 650 1290 760 1020 870 705 Table 141. TENSILE STRENGTH OF N ICKEL-BASE SUPERALLOYS (SHEET 4 OF 5) Alloy Temperature (°C) Tensile Strength (MPa) Data from ASM Metals Reference Book, Third Edition, Michael Bauccio, Ed., ASM International, Materials Park, OH, p387-389, (1993). 8.03 Mechanical Page 577 Wednesday, December 31, 1969 17:00 ©2001 CRC Press LLC Mechanical Properties CRC Handbook of Materials Science & Engineering Unitemp AF2–1DA, bar 21 1290 540 1340 650 1360 760 1150 870 830 Waspaloy, bar 21 1280 540 1170 650 1120 760 795 870 525 Table 141. TENSILE STRENGTH OF N ICKEL-BASE SUPERALLOYS (SHEET 5 OF 5) Alloy Temperature (°C) Tensile Strength (MPa) Data from ASM Metals Reference Book, Third Edition, Michael Bauccio, Ed., ASM International, Materials Park, OH, p387-389, (1993). 8.03 Mechanical Page 578 Wednesday, December 31, 1969 17:00 ©2001 CRC Press LLC Table 142. TENSILE STRENGTH OF WROUGHT TITANIUM ALLOYS AT ROOM TEMPERATURE (SHEET 1 OF 3) Class Alloy Condition Tensile Strength (MPa) Commercially Pure 99.5 Ti Annealed 331 99.2 Ti Annealed 434 99.1 Ti Annealed 517 99.0 Ti Annealed 662 99.2Ti-0.2Pd Annealed 434 Ti-0.8Ni-0.3Mo Annealed 517 Alpha Alloys Ti-5Al-2.5Sn Annealed 862 Ti-5Al-2.5Sn (low O 2 ) Annealed 807 Near Alpha Alloys Ti-8Al-1Mo-1V Duplex Annealed 1000 Ti-11Sn-1Mo-2.25Al-5.0Zr-1Mo-0.2Si Duplex Annealed 1103 Ti-6Al-2Sn-4Zr-2Mo Duplex Annealed 979 Ti-5Al-2Sn-2Zr-2Mo-0.25Si 975 ˚C (1/2h), AC + 595˚C (2h), AC 1048 Ti-6Al-2Nb-1Ta-1Mo As rolled 2.5 cm (1 in.) plate 855 Ti-6Al-2Sn-1.5Zr-1Mo- 0.35Bi-0.1Si Beta forge + duplex anneal 1014 Data from ASM Metals Reference Book, Third Edition, Michael Bauccio, Ed., ASM International, Materials Park, OH, p512, (1993). 8.04 Mechanical L Page 579 Wednesday, December 31, 1969 17:00 ©2001 CRC Press LLC Alpha-Beta Alloys Ti-8Mn Annealed 945 Ti-3Al-2.5V Annealed 689 Ti-6Al-4V Annealed 993 Solution + age 1172 Ti-6Al-4V(low O 2 ) Annealed 896 Ti-6Al-6V-2Sn Annealed 1069 Solution + age 1276 Ti-7Al-4Mo Solution + age 1103 Ti-6Al-2Sn-4Zr-6Mo Solution + age 1269 Ti-6Al-2Sn-2Zr-2Mo- 2Cr-0.25Si Solution + age 1276 Ti-10V-2Fe-3Al Solution + age 1276 Table 142. TENSILE STRENGTH OF WROUGHT TITANIUM ALLOYS AT ROOM TEMPERATURE (SHEET 2 OF 3) Class Alloy Condition Tensile Strength (MPa) Data from ASM Metals Reference Book, Third Edition, Michael Bauccio, Ed., ASM International, Materials Park, OH, p512, (1993). 8.04 Mechanical L Page 580 Wednesday, December 31, 1969 17:00 ©2001 CRC Press LLC Beta Alloys Ti-13V-1Cr-3Al Solution + age 1220 1276 Ti-8Mo-8V-2Fe-3Al Solution + age 1310 Ti-3Al-8V-6Cr-4Mo-4Zr Solution + age 1448 Annealed 883 Ti-11.5Mo-6Zr-4.5Sn Solution + age 1386 Table 142. TENSILE STRENGTH OF WROUGHT TITANIUM ALLOYS AT ROOM TEMPERATURE (SHEET 3 OF 3) Class Alloy Condition Tensile Strength (MPa) Data from ASM Metals Reference Book, Third Edition, Michael Bauccio, Ed., ASM International, Materials Park, OH, p512, (1993). 8.04 Mechanical L Page 581 Wednesday, December 31, 1969 17:00 ©2001 CRC Press LLC Table 143. TENSILE STRENGTH OF WROUGHT TITANIUM ALLOYS AT HIGH TEMPERATURE (SHEET 1 OF 4) Class Alloy Condition Test Temperature (°C) Tensile Strength (MPa) Commercially Pure 99.5 Ti Annealed 315 152 99.2 Ti Annealed 315 193 99.1 Ti Annealed 315 234 99.0 Ti Annealed 315 310 99.2Ti-0.2Pd Annealed 315 186 Ti-0.8Ni-0.3Mo Annealed 205 345 Ti-0.8Ni-0.3Mo Annealed 315 324 Alpha Alloys Ti-5Al-2.5Sn Annealed 315 565 Ti-5Al-2.5Sn (low O 2 ) Annealed -195 1241 -255 1579 Near Alpha Alloys Ti-8Al-1Mo-1V Duplex Annealed 315 793 425 738 540 621 Data from ASM Metals Reference Book, Third Edition, Michael Bauccio, Ed., ASM International, Materials Park, OH, p512, (1993). 8.04 Mechanical L Page 582 Wednesday, December 31, 1969 17:00 ©2001 CRC Press LLC Ti-11Sn-1Mo-2.25Al-5.0Zr-1Mo-0.2Si Duplex Annealed 315 896 425 827 540 758 Ti-6Al-2Sn-4Zr-2Mo Duplex Annealed 315 772 425 703 540 648 Ti-5Al-2Sn-2Zr-2Mo-0.25Si 975 ˚C (1/2h), AC + 595 ˚C (2h), AC 315 793 425 779 540 689 Ti-6Al-2Nb-1Ta-1Mo As rolled 2.5 cm (1 in.) plate 315 586 425 517 540 483 Ti-6Al-2Sn-1.5Zr-1Mo- 0.35Bi-0.1Si Beta forge + duplex anneal 480 724 Table 143. TENSILE STRENGTH OF WROUGHT TITANIUM ALLOYS AT HIGH TEMPERATURE (SHEET 2 OF 4) Class Alloy Condition Test Temperature (°C) Tensile Strength (MPa) Data from ASM Metals Reference Book, Third Edition, Michael Bauccio, Ed., ASM International, Materials Park, OH, p512, (1993). 8.04 Mechanical L Page 583 Wednesday, December 31, 1969 17:00 ©2001 CRC Press LLC Alpha-Beta Alloys Ti-8Mn Annealed 315 717 Ti-3Al-2.5V Annealed 315 483 Ti-6Al-4V Annealed 315 724 Annealed 425 669 Annealed 540 531 Solution + age 315 862 Solution + age 425 800 Solution + age 540 655 Ti-6Al-4V(low O 2 ) Annealed 160 1517 Ti-6Al-6V-2Sn Annealed 315 931 Solution + age 315 979 Ti-7Al-4Mo Solution + age 315 976 425 848 Table 143. TENSILE STRENGTH OF WROUGHT TITANIUM ALLOYS AT HIGH TEMPERATURE (SHEET 3 OF 4) Class Alloy Condition Test Temperature (°C) Tensile Strength (MPa) Data from ASM Metals Reference Book, Third Edition, Michael Bauccio, Ed., ASM International, Materials Park, OH, p512, (1993). 8.04 Mechanical L Page 584 Wednesday, December 31, 1969 17:00 ©2001 CRC Press LLC [...]... 1. 26 8 .6 6/10 Nylon General purpose Glass fiber (30%) reinforced 7.1—8.5 19 To convert psi to MPa, multiply by 145 Source: data compiled by J.S Park from Charles T Lynch, CRC Handbook of Materials Science, Vol 3, CRC Press, Boca Raton, Florida, 1975 and Engineered Materials Handbook, Vol.2, Engineering Plastics, ASM International, Metals Park, Ohio, 1988 ©2001 CRC Press LLC 8. 06 Mechanical L Page 60 2... Boston, (1983); and Ceramic Source, American Ceramic Society (19 86- 1991) ©2001 CRC Press LLC CRC Handbook of Materials Science & Engineering 8. 06 Mechanical L Page 593 Wednesday, December 31, 1 969 17:00 Table 1 46 TENSILE STRENGTH OF (SHEET 1 OF 3) GLASS Type Glass Tensile Strength (Kg • mm–2) SiO2 glass (48 µm diameter fiber) ( 56 µm diameter fiber) (60 µm diameter fiber) (65 µm diameter fiber) 49 .6 44.3 42.3... from Charles T Lynch, CRC Handbook of Materials Science, Vol 3, CRC Press, Boca Raton, Florida, 1975 and Engineered Materials Handbook, Vol.2, Engineering Plastics, ASM International, Metals Park, Ohio, 1988 ©2001 CRC Press LLC 8. 06 Mechanical L Page 60 5 Wednesday, December 31, 1 969 17:00 Table 147 TENSILE STRENGTH OF (SHEET 10 OF 12) POLYMERS Class Polymer Tensile Strength, (ASTM D638) (103 psi) Polyethylenes;... from Charles T Lynch, CRC Handbook of Materials Science, Vol 3, CRC Press, Boca Raton, Florida, 1975 and Engineered Materials Handbook, Vol.2, Engineering Plastics, ASM International, Metals Park, Ohio, 1988 ©2001 CRC Press LLC 8. 06 Mechanical L Page 60 7 Wednesday, December 31, 1 969 17:00 Table 147 TENSILE STRENGTH OF (SHEET 12 OF 12) POLYMERS Class Polymer Tensile Strength, (ASTM D638) (103 psi) Silicones... (ASTM D651) 6. 5 4 6 30—35 Ureas; Molded Alpha—cellulose filled (ASTM Type l) 5—10 To convert psi to MPa, multiply by 145 Source: data compiled by J.S Park from Charles T Lynch, CRC Handbook of Materials Science, Vol 3, CRC Press, Boca Raton, Florida, 1975 and Engineered Materials Handbook, Vol.2, Engineering Plastics, ASM International, Metals Park, Ohio, 1988 ©2001 CRC Press LLC 8.07 Mechanical Page 60 8... to (MPa), multiply by 6. 89 Data from ASM Engineering Materials Reference Book, Second Edition, Michael Bauccio, Ed., ASM International, Materials Park, OH, p1 06, (1994) ©2001 CRC Press LLC CRC Handbook of Materials Science & Engineering 8.07 Mechanical Page 60 9 Wednesday, December 31, 1 969 17:00 Mechanical Properties Table 149 TENSILE STRENGTH OF CARBON - AND GLASS REINFORCED ENGINEERING THERMOPLASTICS... phenolic—asbestos 6 4.5—9 3—5 4 ABS–Polycarbonate Alloy 8.2 5.0—8.5 5.0—8.5 5—9 5—10 To convert psi to MPa, multiply by 145 Source: data compiled by J.S Park from Charles T Lynch, CRC Handbook of Materials Science, Vol 3, CRC Press, Boca Raton, Florida, 1975 and Engineered Materials Handbook, Vol.2, Engineering Plastics, ASM International, Metals Park, Ohio, 1988 ©2001 CRC Press LLC 8. 06 Mechanical L Page 60 3 Wednesday,... purpose 5—10 4 6 15—17 Polyesters: Thermosets Reinforced polyester moldings To convert psi to MPa, multiply by 145 Source: data compiled by J.S Park from Charles T Lynch, CRC Handbook of Materials Science, Vol 3, CRC Press, Boca Raton, Florida, 1975 and Engineered Materials Handbook, Vol.2, Engineering Plastics, ASM International, Metals Park, Ohio, 1988 ©2001 CRC Press LLC 8. 06 Mechanical L Page 60 4 Wednesday,... Charles T Lynch, CRC Handbook of Materials Science, Vol 3, CRC Press, Boca Raton, Florida, 1975 and Engineered Materials Handbook, Vol.2, Engineering Plastics, ASM International, Metals Park, Ohio, 1988 ©2001 CRC Press LLC 8. 06 Mechanical L Page 60 6 Wednesday, December 31, 1 969 17:00 Table 147 TENSILE STRENGTH OF (SHEET 11 OF 12) POLYMERS Class Polymer Tensile Strength, (ASTM D638) (103 psi) Polystyrenes... rigid Glass cloth laminate 9 .6 12.0 59.2 Filler & type Cellulose electrical Glass fiber Alpha cellulose and mineral 5—9 6 9 5—8 Melamines; Molded 8—12 5.2—5.3 50—52 To convert psi to MPa, multiply by 145 Source: data compiled by J.S Park from Charles T Lynch, CRC Handbook of Materials Science, Vol 3, CRC Press, Boca Raton, Florida, 1975 and Engineered Materials Handbook, Vol.2, Engineering Plastics, ASM . Mechanical Properties CRC Handbook of Materials Science & Engineering Nimonic 75, bar 21 750 540 63 5 65 0 538 760 290 870 145 Nimonic 80A, bar 21 1240 540 1100 65 0 1000 760 760 870 400 Nimonic. 1420 540 1400 65 0 1340 760 1100 870 62 0 René 95, bar 21 162 0 540 1540 65 0 1 460 760 1170 Udimet 500, bar 21 1310 540 1240 65 0 1210 760 1040 870 64 0 Udimet 520, bar 21 1310 540 1240 65 0 1170 760 725 870. 1100 65 0 1030 760 825 870 430 Nimonic 105, bar 21 1140 540 1100 65 0 1080 760 965 870 60 5 Nimonic 115, bar 21 1240 540 1090 65 0 1120 760 1080 870 825 Pyromet 860 , bar 21 1300 540 1250 65 0 1110 760