Đang tải... (xem toàn văn)
Tài liệu hướng dẫn sửa chữa Hệ thống cửa kính trên xe Toyota camry hybrid xv50 2012 2017 windshield he thong cua kinh. Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành sửa chữa nhanh chóng, hiệu quả, chính xác
WS–4 WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM SYSTEM DIAGRAM M1 Power Window Regulator Master Switch Assembly 16 PU 15 PD B H6 Power Window Regulator Switch H4 Assembly (Front Passenger) Power Window Regulator Motor from POWER fuse from POWER fuse B SU SD U D K1 Power Window Regulator Switch Assembly (Rear RH) from RR DOOR RH fuse RLU 12 RLD 13 B SU SD U D J1 Power Window Regulator Switch Assembly (Rear LH) 10 RRU 18 RRD WS from RR DOOR LH fuse B SU SD U D K3 Power Window Regulator Motor J3 Power Window Regulator Motor I4 Power Window Regulator Motor (Front LH) DD DU E B145473E03 WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM WS–5 SYSTEM DESCRIPTION POWER WINDOW CONTROL SYSTEM DESCRIPTION (a) The power window control system controls the power window operation using the power window regulator motors The main controls of this system are the power window regulator master switch, which is mounted on the driver side door, and the power window regulator switches, which are mounted on the passenger side door and rear doors Operating a window switch results in electrical power being transmitted to the corresponding power window regulator motor (b) The power window control system has the following functions: Function Outline Manual up-and-down function Function that causes window to go up while power window switch is being pulled halfway up and to go down while pushed halfway down Window stops as soon as the switch is released Remote control function Function that allows power window master switch to control MANUAL up-and-down operations of front passenger door window and rear door windows Key-off operation function Function that makes it possible to operate power window for approx 43 seconds after power switch is on (ACC) or off, if either front door is not opened WS WS–6 WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM HOW TO PROCEED WITH TROUBLESHOOTING HINT: • Use the following procedure to troubleshoot the power window control system • The intelligent tester should be used in step VEHICLE BROUGHT TO WORKSHOP NEXT CUSTOMER PROBLEM ANALYSIS CHECK AND SYMPTOM CHECK NEXT PROBLEM SYMPTOMS TABLE HINT: See page WS-7 NEXT WS OVERALL ANALYSIS AND TROUBLESHOOTING (a) Circuit inspection (b) Terminal of ECU HINT: See page WS-8 NEXT ADJUST, REPAIR OR REPLACE NEXT END OPERATION CHECK B140183 CHECK WINDOW LOCK SWITCH (a) Check that the front passenger side power window and rear power windows operation are disabled when the window lock switch of the power window master switch is pressed Standard: Front passenger side power window and rear power windows operation are disabled WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM WS–7 (b) Check that the front passenger side power window and rear power windows can be operated when the window lock switch is pressed again Standard: Front passenger side power window and rear power windows can be operated CHECK MANUAL UP/DOWN FUNCTION (a) Check that the driver side power window operates as follows: Standard Condition Master Switch Power switch on (IG) Driver side Switch Operation Power Window Pulled halfway up UP (Closed) Pushed halfway down DOWN (Open) (b) Check that the power windows except the driver side power window operate as follows: Standard Condition Switch Passenger side • • Power switch on (IG) Window lock switch OFF Rear LH Rear RH Switch Operation Power Window Pulled up UP (Closed) Pushed down DOWN (Open) Pulled up UP (Closed) Pushed down DOWN (Open) Pulled up UP (Closed) Pushed down DOWN (Open) CHECK AUTO DOWN FUNCTION (a) Check that the driver side power window operates as follows: Standard Condition Power switch on (IG) Master Switch Driver side Switch Operation Power Window Pulled up fully UP (Closed) Pushed down fully DOWN (Open) CHECK REMOTE MANUAL UP/DOWN FUNCTION (a) Check that the power windows except the driver side power window operate as follows: Standard Condition Master Switch Passenger side • • Power switch on (IG) Window lock switch OFF Rear LH Rear RH Switch Operation Power Window Pulled up UP (Closed) Pushed down DOWN (Open) Pulled up UP (Closed) Pushed down DOWN (Open) Pulled up UP (Closed) Pushed down DOWN (Open) WS WS–8 WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM PROBLEM SYMPTOMS TABLE POWER WINDOW CONTROL SYSTEM Symptom Suspected Area POWER, RR DOOR LH/RH fuses Power window does not operate with power window regulator master switch Front passenger side power window does not operate with power window regulator switch Rear LH side power window does not operate with power window regulator switch Rear RH side power window does not operate with power window regulator switch Remote UP/DOWN function does not operate Power window can be operated after power switch is turned off even if operated conditions are not met WS See page - Power window master switch circuit (power source) WS-12 Power window regulator motor circuit WS-18 Power window regulator master switch WS-27 Power window switch circuit (power source) WS-15 Power window regulator motor circuit (front passenger side) WS-20 Power window regulator switch (front passenger side) WS-15 Power window switch circuit (power source) WS-16 Power window regulator motor circuit (rear LH side) WS-22 Power window regulator switch (rear LH side) WS-32 Power window switch circuit (power source) WS-17 Power window regulator motor circuit (rear RH side) WS-24 Power window regulator switch (rear RH side) WS-32 Power window regulator master switch WS-12 Wire harness Front door courtesy switch Wire harness LI-105 - WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM WS–9 TERMINALS OF ECU POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY M1 B137056E01 (a) Disconnect the M1 switch connector (b) Measure the voltage and resistance of each terminal according to the value(s) in the table below Standard resistance Symbols (Terminal No.) Wiring Color E (M1-1) - Body ground W-B - Body ground Terminal Description Condition Specified Condition Ground Always Below Ω Terminal Description Condition Specified Condition Power switch on (IG) 10 to 14 V Standard voltage Symbols (Terminal No.) Wiring Color B (M1-6) - E (M1-1) GR - W-B Power supply If the result is not as specified, there may be a malfunction in the wire harness (c) Reconnect the M1 switch connector and reset the power window motor (d) Measure the voltage according to the value(s) in the table below Standard voltage Symbols (Terminal No.) DU (M1-3) - E (M1-1) DD (M1-4) - E (M1-1) PU (M1-16) - E (M1-1) PD (M1-15) - E (M1-1) RLU (M1-12) - E (M1-1) Condition Specified Condition G - W-B Power window motor UP output Power switch on (IG), driver side power window switch OFF → UP (Manual operation) V → 10 to 14 V BR - W-B Power window motor DOWN output Power switch on (IG), driver side power window switch OFF → DOWN (Manual operation) V → 10 to 14 V W - W-B Power window motor UP output Power switch on (IG), front passenger side power window switch OFF → UP (Manual operation) V → 10 to 14 V R - W-B Power window motor DOWN output Power switch on (IG), front passenger side power window switch OFF → DOWN (Manual operation) V → 10 to 14 V L - W-B Power window motor UP output Power switch on (IG), rear LH side power window switch OFF → UP (Manual operation) V → 10 to 14 V Wiring Color Terminal Description WS WS–10 WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM Condition Specified Condition Power window motor DOWN output Power switch on (IG), rear LH side power window switch OFF → DOWN (Manual operation) V → 10 to 14 V Y - W-B Power window motor UP output Power switch on (IG), rear RH side power window switch OFF → UP (Manual operation) V → 10 to 14 V LG - W-B Power window motor DOWN output Power switch on (IG), rear RH side power window switch OFF → DOWN (Manual operation) V → 10 to 14 V Symbols (Terminal No.) Wiring Color RLD (M1-13) - E (M1-1) B - W-B RRU (M1-10) - E (M1-1) RRD (M1-18) - E (M1-1) Terminal Description If the result is not as specified, there may be a malfunction in the wire harness CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT RH) H6 B137057E01 WS (a) Disconnect the H6 switch connector (b) Measure the voltage according to the value(s) in the table below Standard voltage Symbols (Terminal No.) Wiring Color B (H6-3) - Body ground GR - Body ground Terminal Description Power supply Condition Specified Condition Power switch on (IG) 10 to 14 V If the result is not as specified, there may be a malfunction in the wire harness (c) Reconnect the H6 switch connector and reset the power window motor (d) Measure the voltage according to the value(s) in the table below Standard voltage Symbols (Terminal No.) Wiring Color U (H6-4) - Body ground G - Body ground D (H6-1) - Body ground Y - Body ground Condition Specified Condition Power window motor UP output Power switch on (IG), front passenger side power window switch OFF → UP (Manual operation) V → 10 to 14 V Power window motor DOWN output Power switch on (IG), front passenger side power window switch OFF → DOWN (Manual operation) V → 10 to 14 V Terminal Description If the result is not as specified, the power window regulator switch assembly may have a malfunction WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM WS–11 CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR LH) K1 B137057E02 (a) Disconnect the K1 switch connector (b) Measure the voltage according to the value(s) in the table below Standard voltage Symbols (Terminal No.) Wiring Color B (K1-3) - Body ground R - Body ground Terminal Description Power supply Condition Specified Condition Power switch on (IG) 10 to 14 V If the result is not as specified, there may be a malfunction in the wire harness (c) Reconnect the K1 switch connector and reset the power window motor (d) Measure the voltage according to the value(s) in the table below Standard voltage Symbols (Terminal No.) Wiring Color U (K1-4) - Body ground V - Body ground D (K1-1) - Body ground R - Body ground Condition Specified Condition Power window motor UP output Power switch on (IG), front passenger side power window switch OFF → UP (Manual operation) V → 10 to 14 V Power window motor DOWN output Power switch on (IG), front passenger side power window switch OFF → DOWN (Manual operation) V → 10 to 14 V Terminal Description If the result is not as specified, the power window regulator switch assembly may have a malfunction CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR RH) J1 B137057E03 (a) Disconnect the J1 switch connector WS WS–12 WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM (b) Measure the voltage according to the value(s) in the table below Standard voltage Symbols (Terminal No.) Wiring Color B (J1-3) - Body ground R - Body ground Terminal Description Power supply Condition Specified Condition Power switch on (IG) 10 to 14 V If the result is not as specified, there may be a malfunction in the wire harness (c) Reconnect the J1 switch connector and reset the power window motor (d) Measure the voltage according to the value(s) in the table below Standard voltage Symbols (Terminal No.) Wiring Color U (J1-4) - Body ground V - Body ground D (J1-1) - Body ground R - Body ground Condition Specified Condition Power window motor UP output Power switch on (IG), front passenger side power window switch OFF → UP (Manual operation) V → 10 to 14 V Power window motor DOWN output Power switch on (IG), front passenger side power window switch OFF → DOWN (Manual operation) V → 10 to 14 V Terminal Description If the result is not as specified, the power window regulator switch assembly may have a malfunction WS WINDSHIELD / WINDOWGLASS – REAR POWER WINDOW SWITCH WS–33 INSTALLATION INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (See page ED-80) INSTALL REAR DOOR INNER GLASS WEATHERSTRIP (See page ED-80) INSTALL REAR DOOR INSIDE HANDLE SUBASSEMBLY (See page ED-80) INSTALL REAR DOOR TRIM BOARD SUBASSEMBLY (See page ED-81) INSTALL DOOR ASSIST GRIP COVER (See page ED82) INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG (See page ED-82) WS WS–24 WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM CHECK WIRE HARNESS (WINDOW REGULATOR MOTOR - WINDOW REGULATOR SWITCH) (a) Disconnect the K1 and K3 connectors (b) Measure the resistance according to the value(s) in the table below Standard resistance K1 Power Window Regulator Switch Assembly (Rear LH): D Tester Connection Condition Specified Condition K1-4 (U) - K3-1 Always Below Ω K1-1 (D) - K3-2 Always Below Ω K1-4 (U) - Body ground Always 10 kΩ or higher K1-1 (D) - Body ground Always 10 kΩ or higher U NG K3 Power Window Regulator Motor (Rear LH): REPAIR OR REPLACE HARNESS OR CONNECTOR B137066E02 WS OK PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE WS–40 WINDSHIELD / WINDOWGLASS – WINDSHIELD GLASS WINDSHIELD GLASS WINDSHIELD / WINDOWGLASS BODY COMPONENTS ROOF HEADLINING ASSEMBLY FRONT ASSIST GRIP SUB-ASSEMBLY ASSIST GRIP COVER VISOR BRACKET COVER VISOR ASSEMBLY RH FRONT PILLAR GARNISH CLIP VISOR HOLDER ROOF CONSOLE BOX ASSEMBLY FRONT ASSIST GRIP SUB-ASSEMBLY ASSIST GRIP COVER VISOR HOLDER VISOR ASSEMBLY LH VISOR BRACKET COVER FRONT DOOR OPENING TRIM WEATHERSTRIP RH WS FRONT PILLAR GARNISH CLIP FRONT PILLAR GARNISH RH FRONT WIPER ARM AND BLADE ASSEMBLY RH 20 (204, 15) FRONT PILLAR GARNISH LH 20 (204, 15) FRONT DOOR OPENING TRIM WEATHERSTRIP LH FRONT WIPER ARM AND BLADE ASSEMBLY LH FRONT FENDER TO COWL SIDE SEAL RH FRONT FENDER TO COWL SIDE SEAL LH N*m (kgf*cm, ft.*lbf) : Specified torque COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY Non-reusable part B149544E01 WINDSHIELD / WINDOWGLASS – WINDSHIELD GLASS WS–41 INNER REAR VIEW MIRROR STAY HOLDER COVER INNER REAR VIEW MIRROR ASSEMBLY 1.8 (18, 16 in.*lbf) NO WINDSHIELD GLASS STOPPER *2 NO WINDSHIELD GLASS STOPPER *1 NO WINDSHIELD GLASS STOPPER *2 WINDSHIELD GLASS WS WINDSHIELD MOULDING WINDOW GLASS ADHESIVE DAM WINDSHIELD GLASS RETAINER WINDSHIELD GLASS RETAINER *1: 1-Piece type *2: 2-Piece type WINDSHIELD GLASS ASSEMBLY Non-reusable part N*m (kgf*cm, ft.*lbf) : Specified torque B146383E01 WS–25 WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM Rear Power Window Motor RH Circuit DESCRIPTION This circuit transmits signals from the power window regulator switch assembly (Rear RH) to the power window regulator motor (Rear RH) WIRING DIAGRAM J1 Power Window Regulator Switch Assembly (Rear RH) J3 Power Window Regulator Motor (Rear RH) U D WS C B137065E05 INSPECTION PROCEDURE INSPECT POWER WINDOW REGULATOR MOTOR Motor Gear Counterclockwise Clockwise B127535E01 (a) Remove the power window motor (b) Apply battery voltage to the motor connector according to the table below NOTICE: Do not apply battery voltage to any terminals except terminals and Standard Measurement Condition Specified Condition Battery positive (+) → Terminal Battery negative (-) → Terminal Motor gear rotates clockwise Battery positive (+) → Terminal Battery negative (-) → Terminal Motor gear rotates counterclockwise NG OK REPLACE POWER WINDOW REGULATOR MOTOR WS–26 WINDSHIELD / WINDOWGLASS – POWER WINDOW CONTROL SYSTEM CHECK WIRE HARNESS (WINDOW REGULATOR MOTOR - WINDOW REGULATOR SWITCH) (a) Disconnect the J1 and J3 connectors (b) Measure the resistance according to the value(s) in the table below Standard resistance J1 Power Window Regulator Switch Assembly (Rear RH): Tester Connection D Condition Specified Condition J1-4 (U) - J3-1 Always Below Ω J1-1 (D) - J3-2 Always Below Ω J1-4 (U) - Body ground Always 10 kΩ or higher J1-1 (D) - Body ground Always 10 kΩ or higher U NG J3 Power Window Regulator Motor (Rear RH): REPAIR OR REPLACE HARNESS OR CONNECTOR B137066E03 WS OK PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE WS–54 WINDSHIELD / WINDOWGLASS – BACK WINDOW GLASS BACK WINDOW GLASS WINDSHIELD / WINDOWGLASS BODY COMPONENTS REAR SEAT HEADREST ASSEMBLY REAR CENTER SEAT HEADREST ASSEMBLY 18 (184, 13) 18 (184, 13) WS 18 (184, 13) REAR SIDE SEATBACK ASSEMBLY RH SEPARATE TYPE REAR SEATBACK ASSEMBLY RH SEPARATE TYPE REAR SEATBACK ASSEMBLY LH 18 (184, 13) REAR SEAT CUSHION ASSEMBLY REAR SIDE SEATBACK ASSEMBLY LH N*m (kgf*cm, ft.*lbf) : Specified torque B136564E09 WINDSHIELD / WINDOWGLASS – BACK WINDOW GLASS REAR DOOR OPENING TRIM WEATHERSTRIP RH WS–55 ROOF SIDE INNER GARNISH RH ROOF SIDE INNER GARNISH LH REAR DOOR SCUFF PLATE RH WS REAR DOOR OPENING TRIM WEATHERSTRIP LH REAR DOOR SCUFF PLATE LH B142833E02 WS–56 WINDSHIELD / WINDOWGLASS – BACK WINDOW GLASS PACKAGE TRAY TRIM PANEL ASSEMBLY REAR SEAT SHOULDER BELT COVER REAR SEAT SHOULDER BELT HOLE COVER REAR SEAT SHOULDER BELT COVER REAR SEAT OUTER BELT ASSEMBLY WS 18 (184, 13) 42 (428, 31) 42 (428, 31) REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH 42 (428, 31) REAR SEAT OUTER BELT ASSEMBLY N*m (kgf*cm, ft.*lbf) : Specified torque B142834E02 WINDSHIELD / WINDOWGLASS – BACK WINDOW GLASS WS–57 without Sliding Roof: REAR ASSIST GRIP SUB-ASSEMBLY ASSIST GRIP COVER ROOF HEADLINING ASSEMBLY REAR ASSIST GRIP SUB-ASSEMBLY ASSIST GRIP COVER with Sliding Roof: WS REAR ASSIST GRIP SUB-ASSEMBLY ASSIST GRIP COVER ROOF HEADLINING ASSEMBLY REAR ASSIST GRIP SUB-ASSEMBLY ASSIST GRIP COVER SPOT LIGHT ASSEMBLY B146419E01 WS–58 WINDSHIELD / WINDOWGLASS – BACK WINDOW GLASS NO BACK WINDOW GLASS STOPPER *2 NO BACK WINDOW GLASS STOPPER *1 NO BACK WINDOW GLASS STOPPER *2 BACK WINDOW GLASS BACK WINDOW MOULDING WS *1: 1-Piece type *2: 2-Piece type BACK WINDOW GLASS ASSEMBLY Non-reusable part B136129E01 WS–28 WINDSHIELD / WINDOWGLASS – POWER WINDOW MASTER SWITCH INSTALLATION WS INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (See page ED-58) INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP (See page ED-58) INSTALL FRONT DOOR INSIDE HANDLE SUBASSEMBLY (See page ED-59) INSTALL FRONT DOOR TRIM BOARD SUBASSEMBLY (See page ED-59) INSTALL COURTESY LIGHT ASSEMBLY (See page ED-59) INSTALL ASSIST GRIP COVER (See page ED-60) INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG (See page ED-60) INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH (See page ED-60) WINDSHIELD / WINDOWGLASS – WINDOW DEFOGGER SYSTEM WS–69 WINDOW DEFOGGER SYSTEM PRECAUTION NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following system after the cable is reconnected System Name SFI System See procedure IN-43 WS WS–70 WINDSHIELD / WINDOWGLASS – WINDOW DEFOGGER SYSTEM PARTS LOCATION ENGINE ROOM R/B, J/B - RR DEFOG RELAY NOISE FILTER WINDOW DEFOGGER WIRE REAR WINDOW DEFOGGER SWITCH WS A/C AMPLIFIER ASSEMBLY MAIN BODY ECU (INSTRUMENT PANEL J/B) - A/C NO FUSE B148253E01 WS–30 WINDSHIELD / WINDOWGLASS – FRONT PASSENGER SIDE POWER WINDOW SWITCH INSTALLATION WS INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (a) Engage the claws and install the power window regulator switch assembly INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP (See page ED-58) INSTALL FRONT DOOR INSIDE HANDLE SUBASSEMBLY (See page ED-59) INSTALL FRONT DOOR TRIM BOARD SUBASSEMBLY (See page ED-59) INSTALL COURTESY LIGHT ASSEMBLY (See page ED-59) INSTALL ASSIST GRIP COVER (See page ED-60) INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG (See page ED-60) INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH (See page ED-60) WS–84 WINDSHIELD / WINDOWGLASS – DEFOGGER RELAY DEFOGGER RELAY ON-VEHICLE INSPECTION 5 INSPECT DEFOGGER RELAY (Marking: DEFOG) (a) Measure the resistance according to the value(s) in the table below Standard resistance Tester Condition Specified Condition 3-4 Below Ω (when battery voltage is not applied between terminals) 3-5 10 kΩ or higher (when battery voltage is not applied between terminals) 3-5 Below Ω (when battery voltage is applied to terminals and 2) B106753E01 If the result is not as specified, replace the relay WS