www bzfxw com BRITISH STANDARD BS EN 23661 1993 ISO 3661 1977 End suction centrifugal pumps — Baseplate and installation dimensions The European Standard EN 23661 1993 has the status of a British Stan[.]
Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI BRITISH STANDARD End-suction centrifugal pumps — Baseplate and installation dimensions The European Standard EN 23661:1993 has the status of a British Standard UDC 621.671 BS EN 23661:1993 ISO 3661:1977 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI BS EN 23661:1993 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y France Association franỗaise de normalisation Germany Deutsches Institut fỹr Normung e.V Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portuguès da Qualidade Spain Asociación Espola de Normalización y Certificación Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation United Kingdom British Standards Institution This British Standard, having been prepared under the direction of the Machinery and Components Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 September 1993 Amendments issued since publication © BSI 10-1999 Amd No The following BSI references relate to the work on this standard: Committee reference MCE/6 Special announcement in BSI News December 1992 ISBN 580 21909 Date Comments BS EN 23661:1993 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI Contents Page Cooperating organizations Inside front cover National foreword ii Foreword Scope Field of application 3 References Baseplate dimensions Basic installation dimensions Annex ZA (normative) Normative references to international publications with their relevant European publications National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-reference Inside back cover Figure — Basic baseplate and installation dimensions Table — Baseplate reference numbers and dimensions Table — Selection of baseplate number and installation dimensions © BSI 10-1999 i BS EN 23661:1993 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI National foreword This British Standard has been prepared under the direction of the Machinery and Components Standards Policy Committee and is the English language version of EN 23661:1993 End-suction centrifugal pumps — Baseplate and installation dimensions, published by the European Committee for Standardization (CEN) It is identical with ISO 3661:1977, published by the International Organization for Standardization (ISO) EN 23661:1993 was produced as a result of international discussion in which the UK took an active part A British Standard does not purport to include all the necessary provisions of a contract Users of British Standards are responsible for their correct application Compliance with a British Standard does not of itself confer immunity from legal obligations Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages to 6, an inside back cover and a back cover This standard has been updated (see copyright date) and may have had amendments incorporated This will be indicated in the amendment table on the inside front cover ii © BSI 10-1999 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD EN 23661 NORME EUROPÉENNE July 1993 EUROPÄISCHE NORM UDC 621.671 Descriptors: Pumps, centrifugal pumps, specifications, supports, designation, installation, dimensions English version End-suction centrifugal pumps — Baseplate and installation dimensions (ISO 3661:1977) Pompes centrifuges aspiration en bout — Dimensions relatives aux socles l’installation (ISO 3661:1977) Kreiselpumpen mit axialem Eintritt — Grundplatten- und Einbau-Maße (ISO 3661:1977) www.bzfxw.com This European Standard was approved by CEN on 1993-07-19 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels © 1993 Copyright reserved to CEN members Ref No EN 23661:1993 E Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI EN 23661:1993 Foreword In 1990, ISO 3661:1977 End-suction centrifugal pumps — Baseplate and installation dimensions was submitted to the CEN Primary Questionnaire procedure Following the positive result of the CEN/CS Proposal ISO 3661:1977 was submitted to the Formal Vote The result of the Formal Vote was positive This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1994, and conflicting national standards shall be withdrawn at the latest by January 1994 According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom Editorial modification The text of clause 2, Normative references, is to be replaced by: NOTE Normative references to international publications are listed in Annex ZA (normative) www.bzfxw.com © BSI 10-1999 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI EN 23661:1993 Scope References This International Standard specifies the basic baseplate and installation dimensions for end-suction centrifugal pumps Alternative numbers and locations of baseplate fixing holes are given to suit individual installations ISO/R 273, Clearance holes for metric bolts ISO 2858, End-suction centrifugal pumps (rating 16 bar) — Designation, nominal duty point and dimensions IEC Publication 72, Dimensions and output ratings for rotating electrical machines — Frame numbers 56 to 400 and flange numbers F55 to F1080 Field of application The dimensions and other data given in this International Standard are intended primarily for use with centrifugal pumps in accordance with ISO 2858, coupled to foot-mounted electric motors for installation on a foundation Where suitable, this International Standard may be used for other types of pump Baseplate dimensions The dimensions and the reference numbers of baseplates are given in Figure and Table Basic installation dimensions The baseplate number appropriate to a given pump designation and the corresponding electric motor frame number are obtained from Table The dimensions of the baseplate corresponding to this number are then obtained from Table and the basic installation dimensions from the last four columns in Table www.bzfxw.com © BSI 10-1999 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI EN 23661:1993 www.bzfxw.com Figure — Basic baseplate and installation dimensions Table — Baseplate reference numbers and dimensions Dimensions in millimetres Baseplate No L16) 800 900 000 120 250 400 600 800 L2 130 150 170 190 205 230 270 300 L3 540 600 660 740 840 940 060 200 35 35 40 40 45 50 55 55 B1 270 300 340 380 430 480 530 600 B2 360 390 450 490 540 610 660 730 B3 320 350 400 440 490 550 600 670 hmax 125 125 125 140 160 180 200 200 da: clearance hole for bolt M16 M16 M20 M20 M20 M24 M24 M24 L4 ± 25 a To ISO/R 273 (coarse series) © BSI 10-1999 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI EN 23661:1993 Table — Selection of baseplate number and installation dimensions Dimensions in millimetres Electric motor frame No.b Pump sizea 71 80 90 90 100 112 132 132 160 160 180 180 200 225 225 250 280 280 M M 50 50 50 50 65 65 65 65 65 65 65 80 80 80 80 80 80 80 100 100 100 100 100 100 100 125 125 125 125 125 125 125 125 125 150 150 150 200 200 200 32 32 32 32 40 50 40 50 40 40 40 50 65 50 65 50 50 50 65 80 65 80 65 65 65 80 80 80 80 80 100 100 100 100 125 125 125 150 150 150 125 160 200 250 125 125 160 160 200 250 315 125 125 160 160 200 250 315 125 125 160 160 200 250 315 160 200 250 315 400 200 250 315 400 250 315 400 250 315 400 2 2 2 2 S L 2 2 2 2 3 3 3 2 2 2 2 3 3 4 3 3 3 3 3 3 4 5 6 5 L 3 3 3 3 3 3 4 5 5 6 M 3 3 3 3 3 3 4 5 5 6 S M 4 4 4 5 4 4 5 4 5 5 5 6 6 4 4 4 5 4 4 5 4 5 5 5 6 6 M L M L L S M 6 6 5 6 5 6 6 6 7 7 5 6 5 6 6 7 7 7 5 6 5 6 6 6 6 6 8 6 6 6 7 7 8 8 M S M Basic installation dimensions Hmax2)4) 260 260 300 380 260 260 300 300 300 380 405 260 260 320 320 320 405 480 300 300 380 380 405 480 480 380 380 480 480 480 480 480 480 480 450 480 515 480 515 515 A 60 60 60 75 60 60 60 60 60 75 75 60 60 60 60 60 75 75 75 75 75 75 75 90 90 75 75 90 90 90 90 90 90 110 90 110 110 110 110 110 h2a 140 160 180 225 140 140 160 160 180 225 250 160 160 180 180 200 225 280 180 180 200 200 225 250 280 225 250 280 315 355 280 280 315 355 355 355 400 375 400 450 aa 80 80 80 100 80 80 80 80 100 100 125 100 100 100 100 100 125 125 100 100 100 100 100 125 125 125 125 125 125 125 125 140 140 140 140 140 140 160 160 160 www.bzfxw.com 6 6 6 7 7 8 8 6 7 7 7 7 7 8 8 7 7 7 7 7 7 8 8 9 7 7 7 7 7 8 8 9 7 8 8 8 8 9 8 9 8 8 8 8 9 9 9 9 9 8 9 9 9 See note NOTE hmax is the maximum permissible height of the baseplate, including packing that may be used between the baseplate and the pump or motor The actual height may be less NOTE Hmax in Table is the maximum permitted height The actual dimension H may be less The values Hmax given for each pump size take into account the maximum height for the greatest given baseplate number and the centre-line height of the pump or motor, whichever is the greater NOTE On the left side of the bold line in Table 2, the centre-line height of the pump is the greater; on the right side the centre-line height of the electric motor is the greater NOTE Additional sub-structures, for example feet for free-standing installations, vibration dampers, are not included in the dimensions Hmax and hmax NOTE Figure shows the locations for five holes (A, B, C, D and E) Baseplates may have either four (A, B, C and D) or three (A, C and E) holes as determined by the pump manufacturer NOTE In Table 1, the dimensions L1 and B1 are the length and the width respectively of the working surface and not include casting slope a To ISO 2858 IEC 72-1 b To © BSI 10-1999 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI EN 23661:1993 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications These normative references are cited at the appropriate places in the text and the publications are listed hereafter For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision For undated references the latest edition of the publication referred to applies (including amendments) Publication Year Title EN/HD Year ISO 273 Clearance holes for metric bolts 20273 1991 ISO 2858 End-suction centrifugal pumps (rating 16 bar) — Designation, nominal duty point and dimensions 22858 1992 IEC 72-1 Dimensions and output series for rotating electrical machines — Part 1: Frame numbers 56 to 400 and flange numbers F55 to F1080 — — www.bzfxw.com © BSI 10-1999 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI BS EN 23661:1993 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Machinery and Components Standards Policy Committee (MCE/-) to Technical Committee MCE/6, upon which the following bodies were represented: Association of Consulting Engineers Association of High Pressure Water Jetting Contractors British Chemical Engineering Contractors’ Association British Hydromechanics Reserach Association British Pump Manufacturers’ Association Department of Trade and Industry (National Engineering Laboratory) Electricity Association Energy Industries Council Engineering Equipment and Materials Users’ Association Health and Safety Executive Society of Motor Manufacturers and Traders Ltd UK Offshore Operators and Association Limited Water Services Association of England and Wales National annex NB (informative) Cross-reference Publication referred to Corresponding British Standard ISO/R 273:1979 BS 4186:1984 Specification for clearance holes for metric bolts and screws © BSI 10-1999 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Aug 07 12:13:45 BST 2006, Uncontrolled Copy, (c) BSI BS EN 23661:1993 ISO 3661:1977 BSI — British Standards Institution BSI is the independent national body responsible for preparing British Standards It presents the UK view on standards in Europe and at the international level It is incorporated by Royal Charter Revisions British Standards are updated by amendment or revision Users of British Standards should make sure that they possess the latest amendments or editions It is the constant aim of BSI to improve the quality of our products and services We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover Tel: 020 8996 9000 Fax: 020 8996 7400 BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services Tel: 020 8996 9001 Fax: 020 8996 7001 In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service Various BSI electronic information services are also available which give details on all its products and services Contact the Information Centre Tel: 020 8996 7111 Fax: 020 8996 7048 Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards For details of these and other benefits contact Membership Administration Tel: 020 8996 7002 Fax: 020 8996 7001 Copyright Copyright subsists in all BSI publications BSI also holds the copyright, in the UK, of the publications of the international standardization bodies Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained BSI 389 Chiswick High Road London W4 4AL If permission is granted, the terms may include royalty payments or a licensing agreement Details and advice can be obtained from the Copyright Manager Tel: 020 8996 7070