BRITISH STANDARD AUTOMOBILE SERIES BS AU 233 1989 ISO 9458 1988 Specification for Starter motor electrical connections for passenger cars L ic e n s e d C o p y L o n d o n S o u th B a n k U n iv e r[.]
Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 05: G M T+00: 00 2006, U n trol l ed Copy, (c) BSI BRITISH STANDARD AUTOMOBILE SERIES Specification for Starter motor electrical connections for passenger cars BS AU 233:1989 ISO 9458:1988 Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 05: G M T+00: 00 2006, U n trol l ed Copy, (c) BSI BS AU 233:1989 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Automobile Standards Policy Committee (AUE/- ) to Technical Committee AUE/1 6, upon which the following bodies were represented: Association of Trailer Manufacturers British Cable Makers’ Confederation Department of Transport (Highways) Department of Transport (Transport and Road Research Laboratory) Department of Trade and Industry Institution of Electronic and Radio Engineers National Caravan Council Ltd Society of Motor Manufacturers and Traders Ltd This British Standard, having been prepared under the direction of the Automobile Standards Policy Committee, was published under the authority of the Board of BSI and comes into effect on 29 September 989 © BSI 01 - 2000 The following BSI references relate to the work on this standard: Committee reference AUE/1 Draft for comment 87/71 51 DC ISBN 580 17434 Amendments issued since publication Amd No Date of issue Comments Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 05: G M T+00: 00 2006, U n trol l ed Copy, (c) BSI BS AU 233:1989 Contents Page Committees responsib le National foreword ii Scope and field of application Reference D imensions and tolerances O ther specifications Figure — Positive terminal to battery — Preferred type Figure — Positive terminal to battery — Alternative type Figure — Positive terminal to solenoid — Alternative Figure — Positive terminal to solenoid — Alternative 2 Tab le Pub lication referred to © BSI 01 - 000 Inside front cover Inside back cover i Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 05: G M T+00: 00 2006, U n trol l ed Copy, (c) BSI BS AU 3 : 989 National fore word This British Standard has been prepared under the direction of the Automobile Passenger cars — Starter motor electrical connections”, published by the International Standards Policy Committee and is identical with ISO 9458: 988 “ Organization for Standardization (ISO) C ross re fe re nce The Technical Committee has reviewed the provisions of ISO 8092- , to which reference is made in the text, and has decided that they are acceptable for use in conj unction with this standard A British Standard does not purport to include all the necessary provisions of a contract Users of British Standards are responsible for their correct application C omp liance with a British S tand ard d oe s no t of itse lf confe r immunity from le gal ob ligatio ns S ummary of p age s This document comprises a front cover, an inside front cover, pages i and ii, pages and 2, an inside back cover and a back cover This standard has been updated (see copyright date) and may have had amendments incorporated This will be indicated in the amendment table on the inside front cover ii © BSI 01 - 2000 Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 05: G M T+00: 00 2006, U n trol l ed Copy, (c) BSI BS AU 3 : 989 S cop e and fie ld of ap p lication This International Standard specifies the requirements for electrical connections used on the starter motors of passenger cars The specifications of this International Standard apply to the positive terminals of the starter motor to the battery and to the solenoid Re fe re nce ISO 8092 - , Road vehicles — Flat quick- connect terminations — Part : Tabs for single pole connections 1) D ime nsions and tole rance s Batte ry p o sitive te rminal Figure — Po sitive te rminal to b atte ry — Alte rnative typ e The dimensions shown in Figure and Figure , and the Table shall apply to the battery positive Tab le terminal of the starter motor D imensions in millimetres S tarte r mo to r d l a 6g ±2 max p ower kW 0, to , , to , M8 14 2,5 E ither M8 or M1 threads and corresponding dimensions can be used, by agreement b etween vehicle and starter motor manufacturers , to M1 16 Figure — Po sitive te rminal to b atte ry — Pre fe rre d typ e 1) At present at the stage of draft © BSI 01 - 000 Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 05: G M T+00: 00 2006, U n trol l ed Copy, (c) BSI BS AU 3 : 989 S o le noid p ositive te rminal The dimensions given in Figure and Figure are recommended for the solenoid p ositive terminal of the s tarter motor, for s tarter motor p ower b etween 0, and kW Figure — Po sitive te rminal to sole noid — Alte rnative O ther sp ecifications Ap art from the dimensions indicated in this International S tandard, all other sp ecifications are left to the dis cretion of the manufacturer Figure — Positive te rminal to sole noid — Alte rnative © BS I - 00 Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 05: G M T+00: 00 2006, U n trol l ed Copy, (c) BSI BS AU 233:1989 Publication referred to See national foreword © BSI 01 - 000 Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 05: G M T+00: 00 2006, U n trol l ed Copy, (c) BSI BS AU 233:1989 ISO 9458:1988 BSI — British Standards Institution BS I is the indep endent national b ody res p ons ib le for p rep aring Britis h S tandards It p res ents the UK view on s tandards in E urop e and at the international level It is incorp orated b y Royal C harter Revisions Britis h S tandards are up dated b y amendment or revis ion Us ers of Britis h S tandards should make s ure that they p oss es s the latest amendments or editions It is the constant aim of BS I to imp rove the quality of our p roducts and services We would b e grateful if anyone finding an inaccuracy or amb iguity while us ing this Britis h S tandard would inform the S ecretary of the technical committee res p ons ib le, the identity of which can b e found on the inside front cover Tel: 02 89 96 90 00 Fax: 02 89 96 40 BS I offers memb ers an individual up dating s ervice called PLUS which ens ures that s ub s crib ers automatically receive the lates t editions of s tandards Buying standards O rders for all BS I, international and foreign s tandards p ub lications s hould b e addres s ed to C us tomer S ervices Tel: 899 00 Fax: 899 7001 In res p ons e to orders for international standards , it is BS I p olicy to sup p ly the BS I imp lementation of thos e that have b een p ub lis hed as Britis h S tandards, unless otherwis e requested Information on standards BS I p rovides a wide range of information on national, E urop ean and international standards through its Lib rary and its Technical H elp to E xp orters S ervice Various BS I electronic information s ervices are also availab le which give details on all its p roducts and s ervices C ontact the Information C entre Tel: 02 89 96 71 1 Fax: 02 89 96 048 S ub s crib ing memb ers of BS I are kep t up to date with s tandards develop ments and receive sub s tantial discounts on the p urchase p rice of s tandards For details of thes e and other b enefits contact Memb ership Adminis tration Tel: 02 89 96 70 02 Fax: 02 89 96 00 Copyright C op yright s ub s is ts in all BS I p ub lications BS I als o holds the cop yright, in the UK, of the p ub lications of the international s tandardization b odies E xcep t as p ermitted under the C op yright, D es igns and Patents Act 988 no extract may b e rep roduced, s tored in a retrieval s ystem or transmitted in any form or b y any means – electronic, p hotocop ying, recording or otherwis e – without p rior written p ermis s ion from BS I This does not p reclude the free us e, in the cours e of imp lementing the standard, of necess ary details such as s ymb ols, and size, typ e or grade designations If thes e details are to b e used for any other p urp os e than imp lementation then the p rior written p ermiss ion of BS I must b e ob tained If p ermis sion is granted, the terms may include royalty p ayments or a licensing agreement D etails and advice can b e ob tained from the C op yright Manager BS I 89 C his wick H igh Road London W4 4AL Tel: 02 89 96 70