© ISO 2016 Plastics — Symbols and abbreviated terms — Part 4 Flame retardants AMENDMENT 1 Code numbers Plastiques — Symboles et abréviations — Partie 4 Ignifuges AMENDEMENT 1 Numéros de code INTERNATI[.]
INTERNATIONAL STANDARD ISO 1043-4 First edition 1998-02-15 AMENDMENT 2016-04-15 Plastics — Symbols and abbreviated terms — Part 4: Flame retardants AMENDMENT 1: Code numbers Plastiques — Symboles et abréviations — Partie 4: Ignifuges AMENDEMENT 1: Numéros de code Reference number ISO 1043-4:1998/Amd.1:2016(E) © ISO 2016 ISO 1043-4:1998/Amd.1:2016(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2016, Published in Switzerland All rights reserved Unless otherwise specified, no part o f this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country o f the requester ISO copyright o ffice Ch de Blandonnet • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel +41 22 749 01 11 Fax +41 22 749 09 47 copyright@iso.org www.iso.org ii © ISO 2016 – All rights reserved ISO 1043-4:1998/Amd.1:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work o f preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o f electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part In particular the different approval criteria needed for the di fferent types o f ISO documents should be noted This document was dra fted in accordance with the editorial rules of the ISO/IEC Directives, Part (see www.iso.org/directives) Attention is drawn to the possibility that some o f the elements o f this document may be the subject o f patent rights ISO shall not be held responsible for identi fying any or all such patent rights Details o f any patent rights identified during the development o f the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents) Any trade name used in this document is in formation given for the convenience o f users and does not constitute an endorsement For an explanation on the meaning o f ISO specific terms and expressions related to formity assessment, as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword – Supplementary information The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 1, Terminology Hexabromocyclododecane (HBCD) is now regulated as persistent organic pollutant (POP); thus, is excluded from codes 14 and 15 and is newly assigned to codes 23 and 24 Silica is an inorganic compound and not an organic compound “Silica compounds ” is changed to “Silicon compounds” © ISO 2016 – All rights reserved iii ISO 1043-4:1998/Amd.1:2016(E) Plastics — Symbols and abbreviated terms — Part 4: Flame retardants AMENDMENT 1: Code numbers Clause 5, page Add “(excluding hexabromocyclododecane)” a fter the word “compounds” for code 14 and a fter the first “compounds” word for code 15, in order to read: 14 aliphatic/alicyclic brominated compounds (excluding hexabromocyclododecane) 15 aliphatic/alicyclic brominated compounds (excluding hexabromocyclododecane) in combination with antimony compounds Delete “23, 24 not allocated” and add the following: 23 hexabromocyclododecane 24 hexabromocyclododecane with antimony compounds Clause 5, page Replace “Silica compounds” with “Silicon compounds” In code 75, replace the word “silica” with “silicon” in order to read: 75 inorganic silicon compounds In code 76, replace the word “silica” with “silicon” and add the word “(silicones)” after the word “compounds” in order to read: 76 organic silicon compounds (silicones) © ISO 2016 – All rights reserved ISO 1043-4:1998/Amd.1:2016(E) ICS 83 080.01 ; 83 040.3 Price based on page © ISO 2016 – All rights reserved