ISO TC 4/SC Reference number ISO 15 2011(E) © ISO 2011 INTERNATIONAL STANDARD ISO 15 Third edition 2011 03 01 Rolling bearings — Radial bearings — Boundary dimensions, general plan Roulements — Roulem[.]
INTERNATIONAL STANDARD ISO 15 Third edition 2011-03-01 Rolling bearings — Radial bearings — Boundary dimensions, general plan Roulements — Roulements radiaux — Dimensions d'encombrement, plan général `,,```,,,,````-`-`,,`,,`,`,,` - Reference number ISO 15:2011(E) Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 Not for Resale ISO 15:2011(E) PDF disclaimer This PDF file may contain embedded typefaces In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy The ISO Central Secretariat accepts no liability in this area Adobe is a trademark of Adobe Systems Incorporated Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing Every care has been taken to ensure that the file is suitable for use by ISO member bodies In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below COPYRIGHT PROTECTED DOCUMENT © ISO 2011 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester `,,```,,,,````-`-`,,`,,`,`,,` - ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyright@iso.org Web www.iso.org Published in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale ISO 15:2011(E) Contents Page Foreword iv `,,```,,,,````-`-`,,`,,`,`,,` - Introduction .v Scope Normative references Terms and definitions Symbols Boundary dimensions Annex A (informative) Guidelines for the extension of this International Standard for radial bearings 17 Bibliography 19 © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS iii Not for Resale ISO 15:2011(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work of preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part The main task of technical committees is to prepare International Standards Draft International Standards adopted by the technical committees are circulated to the member bodies for voting Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights ISO shall not be held responsible for identifying any or all such patent rights ISO 15 was prepared by Technical Committee ISO/TC 4, Rolling bearings This third edition cancels and replaces the second edition (ISO 15:1998), of which it constitutes a minor revision, mainly to update references and terminology `,,```,,,,````-`-`,,`,,`,`,,` - iv Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale ISO 15:2011(E) Introduction The object of the general plan (this International Standard) is to restrict the number of radial bearing sizes enough to ensure economic production, yet to provide a sufficient number of sizes to satisfy present and future needs of bearing users These needs are comprehensive and varying Therefore, the general plan needs to embrace a wide range of numerically determined sizes and proportions and can even be extended according to the guidelines given in Annex A `,,```,,,,````-`-`,,`,,`,`,,` - Tapered roller bearings, insert bearings and some types of needle roller bearings and instrument precision bearings standardized by ISO not conform to this International Standard because the dimensions given are not found to be optimal for the bearings in question © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS v Not for Resale `,,```,,,,````-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale INTERNATIONAL STANDARD ISO 15:2011(E) Rolling bearings — Radial bearings — Boundary dimensions, general plan Scope This International Standard specifies preferred boundary dimensions for radial bearings of the diameter series 7, 8, 9, 0, 1, 2, and Normative references The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies ISO 464, Rolling bearings — Radial bearings with locating snap ring — Dimensions and tolerances ISO 582, Rolling bearings — Chamfer dimensions — Maximum values ISO 5593, Rolling bearings — Vocabulary ISO 12043, Rolling bearings — Single-row cylindrical roller bearings — Chamfer dimensions for loose rib and non-rib sides ISO 12044, Rolling bearings — Single-row angular contact ball bearings — Chamfer dimensions for outer ring non-thrust side ISO 15241, Rolling bearings — Symbols for quantities Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5593 apply Symbols For the purposes of this document, the symbols given in ISO 15241 and the following apply The symbols shown in Figure and given in Tables to denote nominal dimensions, unless specified otherwise B bearing width D bearing outside diameter d bearing bore diameter r chamfer dimension rs smallest single chamfer dimension `,,```,,,,````-`-`,,`,,`,`,,` - © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 15:2011(E) Boundary dimensions Boundary dimensions for radial bearings of the diameter series 7, 8, 9, 0, 1, 2, and are given in Tables to The chamfer dimensions given in Tables to not always apply to: ⎯ the groove side of bearing rings with snap ring groove; these are specified in ISO 464; ⎯ the loose rib and the non-rib sides of cylindrical roller bearing rings; the exceptions are specified in ISO 12043; ⎯ the non-thrust side of angular contact bearing outer rings; these are specified in ISO 12044 Chamfer dimension, r, applies at the corners indicated in Figure and is specified with rs in Tables to The chamfer dimensions for inner rings of bearings with tapered bore may be smaller than those shown in Tables to The corresponding largest single chamfer dimensions to the rs dimensions in Tables to are given in ISO 582 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale `,,```,,,,````-`-`,,`,,`,`,,` - Figure — Radial bearing ISO 15:2011(E) Table — Diameter series d D 17 0,6 1,5 2,5 2,5 0,8 1 1,2 1,5 Dimension series 27 37 B — — — — — 1,8 — 1,8 2,3 7 10 11 2 2,5 2,5 2,5 2,5 2,5 3 10 12 15 12 14 15 18 21 2,5 3 4 17 20 22 25 28 23 27 30 32 35 30 32 35 40 45 47 rs — — — — — 0,05 0,05 0,05 0,05 0,08 3 3,5 3,5 — — — — — 0,08 0,08 0,08 0,1 0,1 — — — — — 3,5 4,5 4,5 5 — — — — — 0,1 0,1 0,1 0,2 0,2 4 4 — — — — — 5 5 — 7 7 0,2 0,2 0,2 0,2 0,2 37 40 44 50 55 4 6 — — — — — 8 10 10 0,2 0,2 0,3 0,3 0,3 50 55 60 65 70 62 68 75 80 85 7 7 — — — — — 10 10 12 12 12 12 13 15 15 15 0,3 0,3 0,3 0,3 0,3 75 80 85 90 95 90 95 105 110 115 7 10 10 10 — — — — — 12 12 15 15 15 15 15 — — — 0,3 0,3 0,6 0,6 0,6 100 105 110 120 130 120 125 135 145 160 10 10 13 13 16 — — — — — 15 15 19 19 23 — — — — — 0,6 0,6 1 140 150 160 170 180 170 180 190 200 215 16 16 16 16 18 — — — — — 23 23 23 23 26 — — — — — 1 1 1,1 190 200 230 240 20 20 — — 30 30 — — 1,1 1,1 © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS `,,```,,,,````-`-`,,`,,`,`,,` - Dimensions in millimetres Not for Resale ISO 15:2011(E) Table — Diameter series Dimensions in millimetres Dimension series D 08 18 28 38 48 58 68 08 B 18 to 68 rs 0,6 1,5 2,5 2,5 — — — — — 1 1,2 1,5 1,8 — — — — — 1,4 1,5 2,3 2,6 — — — — — — — — — — — — — — — — — — — — 0,05 0,05 0,05 0,08 0,08 7 11 13 14 — — — — — 2,5 3,5 3,5 — 3,5 5 6 — — — — — — — — — — — — — — — — — — — — 0,1 0,1 0,15 0,15 0,15 10 12 15 16 17 19 21 24 — — — — — 4 5 5 6 6 7 8 9 — — — — — — — — — — — — — — — 0,2 0,2 0,3 0,3 0,3 17 20 22 25 28 26 32 34 37 40 — 4 4 7 7 — — 10 10 10 10 12 — 12 — — 16 16 16 16 — 22 22 22 22 — 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 30 32 35 40 45 42 44 47 52 58 4 4 7 7 — 8 10 10 10 10 10 12 — 12 12 13 16 16 16 16 18 22 22 22 22 23 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 50 55 60 65 70 65 72 78 85 90 7 10 10 10 10 11 12 13 13 12 13 14 15 15 15 17 18 20 20 20 23 24 27 27 27 30 32 36 36 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,6 0,6 75 80 85 90 95 95 100 110 115 120 8 9 10 10 13 13 13 13 13 16 16 16 15 15 19 19 19 20 20 25 25 25 27 27 34 34 34 36 36 45 45 45 0,3 0,3 0,3 0,3 0,3 0,6 0,6 1 100 105 110 120 130 125 130 140 150 165 9 10 10 11 13 13 16 16 18 16 16 19 19 22 19 19 23 23 26 25 25 30 30 35 34 34 40 40 46 45 45 54 54 63 0,3 0,3 0,6 0,6 0,6 1 1 1,1 140 150 160 170 180 175 190 200 215 225 11 13 13 14 14 18 20 20 22 22 22 24 24 27 27 26 30 30 34 34 35 40 40 45 45 46 54 54 60 60 63 71 71 80 80 0,6 0,6 0,6 0,6 0,6 1,1 1,1 1,1 1,1 1,1 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale `,,```,,,,````-`-`,,`,,`,`,,` - d ISO 15:2011(E) Table — Diameter series Dimensions in millimetres Dimension series d D 09 19 29 39 49 59 69 09 B 19 to 39 49 to 69 rs 1,5 2,5 — — — — — 1,6 2,3 2,5 — — — — — 2,3 2,6 3,5 — — — — — — — — — — — — — — — — — — — — 0,1 0,15 0,15 0,15 0,15 — — — — — 11 13 15 17 19 — — — — — 4 5 — — — — — 7 — 10 10 10 11 — — — — — — — — — — — — — — — 0,15 0,2 0,2 0,3 0,3 — 0,15 0,15 0,15 0,2 10 12 15 17 20 22 24 28 30 — — — — — 6 7 — 8 8,5 8,5 10 10 10 10 11 13 13 13 13 — 16 16 18 18 — 22 22 23 23 — — — — — 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 20 22 25 28 30 37 39 42 45 47 7 7 9 9 11 11 11 11 11 13 13 13 13 13 17 17 17 17 17 23 23 23 23 23 30 30 30 30 30 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 32 35 40 45 50 52 55 62 68 72 7 8 10 10 12 12 12 13 13 14 14 14 15 15 16 16 16 20 20 22 22 22 27 27 30 30 30 36 36 40 40 40 0,3 0,3 0,3 0,3 0,3 0,6 0,6 0,6 0,6 0,6 0,6 0,6 0,6 0,6 0,6 55 60 65 70 75 80 85 90 100 105 9 10 10 13 13 13 16 16 16 16 16 19 19 19 19 19 23 23 25 25 25 30 30 34 34 34 40 40 45 45 45 54 54 0,3 0,3 0,3 0,6 0,6 1 1 1 1 1 80 85 90 95 100 110 120 125 130 140 10 11 11 11 13 16 18 18 18 20 19 22 22 22 24 23 26 26 26 30 30 35 35 35 40 40 46 46 46 54 54 63 63 63 71 0,6 0,6 0,6 0,6 0,6 1,1 1,1 1,1 1,1 1,1 1,1 1,1 1,1 105 110 120 130 140 145 150 165 180 190 13 13 14 16 16 20 20 22 24 24 24 24 27 30 30 30 30 34 37 37 40 40 45 50 50 54 54 60 67 67 71 71 80 90 90 0,6 0,6 0,6 1 1,1 1,1 1,1 1,5 1,5 1,1 1,1 1,1 1,5 1,5 150 160 170 180 210 220 230 250 19 19 19 22 28 28 28 33 36 36 36 42 45 45 45 52 60 60 60 69 80 80 80 95 109 109 109 125 1 1,1 2 2 2 2 `,,```,,,,````-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale ISO 15:2011(E) Table (continued) Dimensions in millimetres Dimension series d D 09 19 29 39 49 59 69 09 B 19 to 39 49 to 69 rs `,,```,,,,````-`-`,,`,,`,`,,` - 190 200 220 240 260 260 280 300 320 360 22 25 25 25 31 33 38 38 38 46 42 48 48 48 60 52 60 60 60 75 69 80 80 80 100 95 109 109 109 136 125 145 145 145 180 1,1 1,5 1,5 1,5 2 2,1 2,1 2,1 2,1 2,1 2,1 2,1 2,1 280 300 320 340 360 380 420 440 460 480 31 37 37 37 37 46 56 56 56 56 60 72 72 72 72 75 90 90 90 90 100 118 118 118 118 136 160 160 160 160 180 218 218 218 218 2,1 2,1 2,1 2,1 2,1 3 3 2,1 3 3 380 400 420 440 460 520 540 560 600 620 44 44 44 50 50 65 65 65 74 74 82 82 82 95 95 106 106 106 118 118 140 140 140 160 160 190 190 190 218 218 250 250 250 290 290 3 4 4 4 4 4 4 480 500 530 560 600 650 670 710 750 800 54 54 57 60 63 78 78 82 85 90 100 100 106 112 118 128 128 136 140 150 170 170 180 190 200 230 230 243 258 272 308 308 325 345 355 4 5 5 5 5 5 5 630 670 710 750 800 850 900 950 000 060 71 73 78 80 82 100 103 106 112 115 128 136 140 145 150 165 170 180 185 195 218 230 243 250 258 300 308 325 335 355 400 412 438 450 462 5 6 6 6 6 6 6 850 900 950 000 060 120 180 250 320 400 85 88 95 103 109 118 122 132 140 150 155 165 175 185 195 200 206 224 236 250 272 280 300 315 335 365 375 400 438 462 488 500 545 580 615 6 6 7,5 6 7,5 7,5 7,5 6 7,5 7,5 7,5 120 180 250 320 400 460 540 630 720 820 109 115 122 128 — 150 160 170 175 185 195 206 218 230 243 250 272 280 300 315 335 355 375 400 425 462 488 515 545 — 615 650 690 710 — 7,5 7,5 7,5 7,5 — 7,5 7,5 7,5 7,5 9,5 7,5 7,5 7,5 7,5 9,5 500 600 700 800 900 950 060 180 300 430 — — — — — 195 200 212 218 230 258 265 280 290 308 335 345 355 375 400 450 462 475 500 530 — — — — — — — — — — — — — — — 9,5 9,5 9,5 12 12 9,5 9,5 9,5 12 12 © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 15:2011(E) Table — Diameter series Dimensions in millimetres Dimension series D 00 10 20 30 40 50 60 00 B 10 to 60 rs 1,5 2,5 12 — — — — — 2,5 2,8 2,8 — — — — — 3,5 — — — — — — — — — — — — — — — — — — — — 0,15 0,15 0,15 0,15 0,2 14 17 19 22 24 — — — — — 6 7 — — 10 10 11 12 — — — 14 15 — — — 19 20 — — — 25 27 — — — — — 0,2 0,3 0,3 0,3 0,3 10 12 15 17 20 26 28 32 35 42 — 8 8 10 12 10 10 11 12 14 12 12 13 14 16 16 16 17 18 22 21 21 23 24 30 29 29 30 32 40 — 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,6 22 25 28 30 32 44 47 52 55 58 8 9 12 12 12 13 13 14 14 15 16 16 16 16 18 19 20 22 22 24 25 26 30 30 32 34 35 40 40 43 45 47 0,3 0,3 0,3 0,3 0,3 0,6 0,6 0,6 1 35 40 45 50 55 62 68 75 80 90 9 10 10 11 14 15 16 16 18 17 18 19 19 22 20 21 23 23 26 27 28 30 30 35 36 38 40 40 46 48 50 54 54 63 0,3 0,3 0,6 0,6 0,6 1 1 1,1 60 65 70 75 80 95 100 110 115 125 11 11 13 13 14 18 18 20 20 22 22 22 24 24 27 26 26 30 30 34 35 35 40 40 45 46 46 54 54 60 63 63 71 71 80 0,6 0,6 0,6 0,6 0,6 1,1 1,1 1,1 1,1 1,1 85 90 95 100 105 130 140 145 150 160 14 16 16 16 18 22 24 24 24 26 27 30 30 30 33 34 37 37 37 41 45 50 50 50 56 60 67 67 67 75 80 90 90 90 100 0,6 1 1 1,1 1,5 1,5 1,5 110 120 130 140 150 170 180 200 210 225 19 19 22 22 24 28 28 33 33 35 36 36 42 42 45 45 46 52 53 56 60 60 69 69 75 80 80 95 95 100 109 109 125 125 136 1 1,1 1,1 1,1 2 2 2,1 160 170 180 240 260 280 25 28 31 38 42 46 48 54 60 60 67 74 80 90 100 109 122 136 145 160 180 1,5 1,5 2,1 2,1 2,1 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale `,,```,,,,````-`-`,,`,,`,`,,` - d ISO 15:2011(E) Table (continued) Dimensions in millimetres Dimension series d D 00 10 20 30 40 50 60 00 B 10 to 60 rs 290 310 340 360 400 31 34 37 37 44 46 51 56 56 65 60 66 72 72 82 75 82 90 92 104 100 109 118 118 140 136 150 160 160 190 180 200 218 218 250 2 2,1 2,1 2,1 2,1 3 280 300 320 340 360 420 460 480 520 540 44 50 50 57 57 65 74 74 82 82 82 95 95 106 106 106 118 121 133 134 140 160 160 180 180 190 218 218 243 243 250 290 290 325 325 4 4 4 5 380 400 420 440 460 560 600 620 650 680 57 63 63 67 71 82 90 90 94 100 106 118 118 122 128 135 148 150 157 163 180 200 200 212 218 243 272 272 280 300 325 355 355 375 400 5 5 5 6 480 500 530 560 600 700 720 780 820 870 71 71 80 82 85 100 100 112 115 118 128 128 145 150 155 165 167 185 195 200 218 218 250 258 272 300 300 335 355 365 400 400 450 462 488 5 6 6 6 6 630 670 710 750 800 920 980 030 090 150 92 100 103 109 112 128 136 140 150 155 170 180 185 195 200 212 230 236 250 258 290 308 315 335 345 388 425 438 462 475 515 560 580 615 630 6 7,5 7,5 7,5 7,5 7,5 7,5 7,5 850 900 950 000 060 220 280 360 420 500 118 122 132 136 140 165 170 180 185 195 212 218 236 243 250 272 280 300 308 325 365 375 412 412 438 500 515 560 560 600 670 690 730 750 800 7,5 7,5 7,5 7,5 9,5 7,5 7,5 7,5 7,5 9,5 120 180 250 320 400 580 660 750 850 950 145 155 — — — 200 212 218 230 243 265 272 290 300 315 345 355 375 400 412 462 475 500 530 545 615 650 — — — 825 875 — — — 9,5 9,5 — — — 9,5 9,5 9,5 12 12 500 600 700 800 120 240 360 500 — — — — 272 280 290 308 355 365 375 400 462 475 500 530 615 630 650 690 — — — — — — — — — — — — 12 12 15 15 `,,```,,,,````-`-`,,`,,`,`,,` - 190 200 220 240 260 © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 15:2011(E) Table — Diameter series Dimensions in millimetres Dimension series d D 01 11 21 31 41 51 61 01 B 11 to 61 rs 15 18 21 23 25 — — — — — — — — — — — 10 10 10 11 12 12 — — 14 15 16 — — 19 20 21 — — 25 27 29 — — — — — 0,3 0,3 0,3 0,3 0,3 10 12 15 17 20 28 30 33 37 44 — — — — — — — — — — 12 12 12 13 15 14 14 14 15 18 18 18 18 20 24 24 24 24 27 32 32 32 32 36 43 — — — — — 0,3 0,3 0,3 0,6 0,6 22 25 28 30 32 47 50 55 58 62 — — — — — — — — — — 16 16 17 18 19 19 19 20 21 23 25 25 27 28 30 34 34 36 38 40 45 45 48 50 54 — — — — — 1 1 35 40 45 50 55 68 75 80 85 95 — — — — — — — — — — 21 22 22 22 24 25 26 26 26 30 33 35 35 35 40 43 46 46 46 54 60 63 63 63 71 — — — — — 1,1 1,1 1,1 1,1 1,1 60 65 70 75 80 100 110 115 125 130 — — — — — — — — — — 24 27 27 30 30 30 34 34 37 37 40 45 45 50 50 54 60 60 67 67 71 80 80 90 90 — — — — — 1,1 1,5 1,5 1,5 1,5 85 90 95 100 105 140 150 160 165 175 — — — 21 22 — — — 30 33 31 33 39 39 42 41 45 52 52 56 56 60 65 65 69 75 80 88 88 95 100 109 118 118 125 — — — 1,1 1,1 1,5 2 2 110 120 130 140 150 180 200 210 225 250 22 25 25 27 31 33 38 38 40 46 42 48 48 50 60 56 62 64 68 80 69 80 80 85 100 95 109 109 115 136 125 145 145 155 180 1,1 1,5 1,5 1,5 2 2 2,1 2,1 160 170 180 190 200 270 280 300 320 340 34 34 37 42 44 51 51 56 60 65 66 66 72 78 82 86 88 96 104 112 109 109 118 128 140 150 150 160 175 190 200 200 218 236 250 2 2,1 3 2,1 2,1 3 220 240 260 280 300 370 400 440 460 500 48 50 57 57 63 69 74 82 82 90 88 95 106 106 118 120 128 144 146 160 150 160 180 180 200 200 218 243 243 272 272 290 325 325 355 4 4 5 `,,```,,,,````-`-`,,`,,`,`,,` - 10 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale ISO 15:2011(E) Table (continued) Dimensions in millimetres Dimension series d D 01 11 21 31 41 51 61 01 B 11 to 61 rs 320 340 360 380 400 540 580 600 620 650 71 78 78 78 80 100 106 106 106 112 128 140 140 140 145 176 190 192 194 200 218 243 243 243 250 300 325 325 325 335 400 438 438 438 450 5 5 5 5 420 440 460 480 500 700 720 760 790 830 88 88 95 100 106 122 122 132 136 145 165 165 175 180 190 224 226 240 248 264 280 280 300 308 325 375 375 400 425 450 500 500 545 560 600 6 6 7,5 6 7,5 7,5 7,5 530 560 600 630 670 870 920 980 030 090 109 115 122 128 136 150 160 170 175 185 195 206 218 230 243 272 280 300 315 336 335 355 375 400 412 462 488 515 545 560 615 650 690 710 750 7,5 7,5 7,5 7,5 7,5 7,5 7,5 7,5 7,5 7,5 710 750 800 850 900 150 220 280 360 420 140 150 155 165 165 195 206 212 224 230 250 272 272 290 300 345 365 375 400 412 438 475 475 500 515 600 630 650 690 710 800 — — — — 9,5 9,5 9,5 12 12 9,5 9,5 9,5 12 12 950 000 060 120 180 500 580 660 750 850 175 185 190 — — 243 258 265 280 290 315 335 345 365 388 438 462 475 475 500 545 580 600 630 670 750 775 800 — — — — — — — 12 12 12 — — 12 12 15 15 15 250 320 400 500 950 060 180 300 — — — — 308 325 345 355 400 425 450 462 530 560 580 600 710 750 775 800 — — — — — — — — — — — — 15 15 19 19 `,,```,,,,````-`-`,,`,,`,`,,` - 11 © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 15:2011(E) Table — Diameter series Dimensions in millimetres Dimension series D 82 02 12 22 32 42 52 62 82 B 02 to 62 rs 10 13 16 19 22 2,5 3,5 5 — — — — — — — — — — 10 11 — — — — — — — — 18 20 — — — 23 27 0,1 0,15 0,15 0,2 0,3 0,15 0,2 0,3 0,3 0,3 10 12 15 24 26 30 32 35 7 8 10 11 — — — — — — — 14 14 14 12 13 14,3 15,9 15,9 — — — — 20 21 23 27 27 27 29 30 36 36 36 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,6 0,6 0,6 17 20 22 25 28 40 47 50 52 58 9 10 10 12 14 14 15 16 — — — — — 16 18 18 18 19 17,5 20,6 20,6 20,6 23 22 27 27 27 30 30 36 36 36 40 40 48 48 48 54 0,3 0,3 0,3 0,3 0,6 0,6 1 1 30 32 35 40 45 62 65 72 80 85 10 11 12 13 13 16 17 17 18 19 — — — — — 20 21 23 23 23 23,8 25 27 30,2 30,2 32 33 37 40 40 43 43 50 54 54 58 60 67 71 71 0,6 0,6 0,6 0,6 0,6 1 1,1 1,1 1,1 50 55 60 65 70 90 100 110 120 125 13 14 16 18 18 20 21 22 23 24 — — — — — 23 25 28 31 31 30,2 33,3 36,5 38,1 39,7 40 45 50 56 56 54 60 67 75 75 71 80 90 100 100 0,6 0,6 1 1,1 1,5 1,5 1,5 1,5 75 80 85 90 95 130 140 150 160 170 18 19 21 22 24 25 26 28 30 32 — — — — — 31 33 36 40 43 41,3 44,4 49,2 52,4 55,6 56 60 65 69 75 75 80 88 95 100 100 109 118 125 136 1 1,1 1,1 1,1 1,5 2 2,1 100 105 110 120 130 180 190 200 215 230 25 27 28 — — 34 36 38 40 40 — — — 42 46 46 50 53 58 64 60,3 65,1 69,8 76 80 80 85 90 95 100 109 115 122 128 136 145 155 160 170 180 1,5 1,5 1,5 — — 2,1 2,1 2,1 2,1 140 150 160 170 180 250 270 290 310 320 — — — — — 42 45 48 52 52 50 54 58 62 62 68 73 80 86 86 88 96 104 110 112 109 118 128 140 140 150 160 175 190 190 200 218 236 250 250 — — — — — 3 4 190 200 220 240 260 340 360 400 440 480 — — — — — 55 58 65 72 80 65 70 78 85 90 92 98 108 120 130 120 128 144 160 174 150 160 180 200 218 200 218 243 272 300 272 290 325 355 400 — — — — — 4 4 12 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale `,,```,,,,````-`-`,,`,,`,`,,` - d ISO 15:2011(E) Table (continued) Dimensions in millimetres Dimension series d D 82 02 12 22 32 42 52 62 82 B 02 to 62 rs 280 300 320 340 360 500 540 580 620 650 — — — — — 80 85 92 92 95 90 98 105 118 122 130 140 150 165 170 176 192 208 224 232 218 243 258 280 290 300 325 355 375 388 400 438 462 500 515 — — — — — 5 6 380 400 420 440 460 680 720 760 790 830 — — — — — 95 103 109 112 118 132 140 150 155 165 175 185 195 200 212 240 256 272 280 296 300 315 335 345 365 400 438 462 475 500 545 580 615 630 670 — — — — — 6 7,5 7,5 7,5 480 500 530 560 600 870 920 980 030 090 — — — — — 125 136 145 150 155 170 185 200 206 212 224 243 258 272 280 310 336 355 365 388 388 412 450 475 488 530 560 600 630 670 710 750 — — — — — — — — 7,5 7,5 9,5 9,5 9,5 630 670 710 750 800 150 220 280 360 420 — — — — — 165 175 180 195 200 230 243 250 265 272 300 315 325 345 355 412 438 450 475 488 515 545 560 615 615 710 750 775 825 — — — — — — — — — — — 12 12 12 15 15 850 900 950 000 500 580 660 750 — — — — 206 218 230 243 280 300 315 330 375 388 412 425 515 515 530 560 650 670 710 750 — — — — — — — — — — — — 15 15 15 15 © ISO for 2011 – All rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS `,,```,,,,````-`-`,,`,,`,`,,` - Not for Resale 13 ISO 15:2011(E) Table — Diameter series Dimensions in millimetres Dimension series D 83 03 13 23 33 83 B 03 to 33 rs 13 16 19 22 26 — — — — — 5 — — — — — — — — 11 13 10 13 15 — — — — — 0,2 0,3 0,3 0,3 0,3 10 12 15 28 30 35 37 42 — — 9 9 10 11 12 13 — — — — — 13 14 17 17 17 15 16 19 19 19 — — 0,3 0,3 0,3 0,3 0,6 0,6 1 17 47 10 14 — 19 22,2 0,6 20 22 25 28 52 56 62 68 10 11 12 13 15 16 17 18 — — — — 21 21 24 24 22,2 25 25,4 30 0,6 0,6 0,6 0,6 1,1 1,1 1,1 1,1 30 32 35 40 45 72 75 80 90 100 13 14 14 16 17 19 20 21 23 25 — — — — — 27 28 31 33 36 30,2 32 34,9 36,5 39,7 0,6 0,6 0,6 1 1,1 1,1 1,5 1,5 1,5 50 55 60 65 70 110 120 130 140 150 19 21 22 24 25 27 29 31 33 35 — — — — — 40 43 46 48 51 44,4 49,2 54 58,7 63,5 1,1 1,1 1,1 1,5 2 2,1 2,1 2,1 75 80 160 170 27 28 37 39 — — 55 58 68,3 68,3 1,5 1,5 2,1 2,1 85 90 95 180 190 200 30 30 33 41 43 45 — — — 60 64 67 73 73 77,8 2 3 100 105 110 120 130 215 225 240 260 280 36 37 42 44 48 47 49 50 55 58 51 53 57 62 66 73 77 80 86 93 82,6 87,3 92,1 106 112 2,1 2,1 3 3 3 14 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2011 – All rights reserved Not for Resale `,,```,,,,````-`-`,,`,,`,`,,` - d