Tạp chí phân tích Hóa, Lý và Sinh học Tập 24, Số 4B/2019 DETERMINATION OF MULTI CLASS PESTICIDES IN SURFACE WATER BY ULTRAHIGH PERFORMANCE LIQUID CHROMATOGRAPHY IN COMBINATION WITH HIGH RESOLUTION MAS[.]
Tạp chí phân tích Hóa, Lý Sinh học - Tập 24, Số 4B/2019 DETERMINATION OF MULTI-CLASS PESTICIDES IN SURFACE WATER BY ULTRAHIGH PERFORMANCE LIQUID CHROMATOGRAPHY IN COMBINATION WITH HIGH RESOLUTION MASS SPECTROMETRY (UPLC-Orbitrap MS) Đến tòa soạn 10-4-2019 Thuy Le Minh, Trung Nguyen Quang, Tung Nguyen Ngoc, Nam Vu Duc, Hung Nguyen Xuan Centre for Research and Technology Transfer, Vietnam Academy of Science and Technology Hai Anh Vu, Lan Anh Nguyen, Tri Tran Manh, Minh Tu Binh Faculty of Chemistry, VNU University of Science, Vietnam National University-Hanoi Dinh Binh Chu School of Chemical Engineering, Hanoi University of Science and Technology Lan Anh Phung Thi School of Environmental Science and Technology, Hanoi University of Science and Technology TÓM TẮT NGHIÊN CỨU XÁC ĐỊNH CÁC HÓA CHẤT BẢO VỆ THỰC VẬT TRONG MẪU NƯỚC MẶT SỬ DỤNG THIẾT BỊ SẮC KÝ LỎNG SIÊU HIỆU NĂNG CAO GHÉP NỐI KHỐI PHỔ PHÂN GIẢI CAO (UPLC-Orbitrap MS) Trong nghiên cứu này, phương pháp sắc ký lỏng ghép nối khối phổ phân giải cao (UPLC-Orbitrap MS) giới thiệu để xác định đa nhóm hóa chất bảo vệ thực vật mẫu nước mặt Quá trình sắc ký sử dụng cột tách Thermo Hypersil Gold PFP (2.1 mm x 100 mm x µm) hệ pha động có chứa mM HCOONH4, 0.1% FA nước deion methanol Phương pháp quét toàn dải (fullscan) độ phân giải 70000 FWHM áp dụng cho chế độ ion dương âm để phát định lượng chất phân tích Các điều kiện sắc ký nhiệt độ cột tách, pha động chương trình dung mơi, tốc dộ dịng thơng số nguồn ion hóa khảo sát tối ưu Sự có mặt chất phân tích mãu thực định tính dựa thời gian lưu, khối lượng phân tử, độ lệch khối, mảnh phổ tương ứng lượng phân mảnh Các chất phân tích tách khỏi mẫu kỹ thuật chiết pha rắn sử dụng cột Water Oasis HLB Các thí nghiệm với mẫu thêm chuẩn thực để đánh giá phương pháp phân tích thơng qua độ lặp lại, hiệu suất thu hồi, khoảng tuyến tính… Phương pháp xây dựng giới hạn phát nằm khoảng từ 0,0002 (Azoxystrobin) – 0,493 ngmL-1 (Parathion-methyl) Cũng nghiên cứu này, phương pháp tối ưu để phân tích đa nhóm chất bảo vệ thực vật 20 mẫu nước sử dụng nông nghiệp, thu thập vùng trồng rau địa bàn Hà Nội Key words: thuốc bảo vệ thực vật, nước mặt, UPLC, Orbitrap MS, chiết pha rắn prevent the increase of harmful pestilent insects, weed and fungi Besides, they are also used to dramatically quality of agricultural INTRODUCTION “Pesticides” play an important role in protecting crop yields [1]-[3] They are synthesized chemicals to limit, inhibit and 153 animals, [4]-[5] improve products [2] However, uncontrolled use of pesticides has been increasing the presence of their residues in various environment They can be dispersed to the atmosphere, released to surrounding soil or transported to surface water Most of pesticides are known as toxic compounds so, their exposure at high level may have the risk of being carcinogenic and mutagenic properties in humans and other animals Facts have shown that presence of pesticides in environment and food is controlled more and more strictly in numerous countries [2], [6] In EU, the legal limits with 0.1 µg L-1 per individual pesticide and 0.5 µg L-1 for the sum of all pesticides was recommended to protect human health and environment [1] In Vietnam, according to a circular no 03/2018/TT-BNNPTNT, more than 30 different pesticides were banned in agriculture [7] Pesticide usage and residue level of not many pesticides in soil, food were also monitored Based on chemical structure, pesticides can be classified into some groups: organophosphate, carbamate, neonicotinoid, strobilurin, triazole, etc Recently, many researches have been published about pesticide analysis in both GC-MS [8]-[9] and LC-MS [10]-[15] Among them, LC-MS/MS technique is the most popular for multi-residue quantitative method of pesticide analysis Moreover, the high resolution mass spectrometry- a method with several advantages, such as excellent mass accuracy, high sensitivity… has been introduced for screening of residual pesticides [10] Also, several sample preparation procedures have been frequently applied such as: liquid-liquid extraction, solid phase extraction, etc., in order to enhance sensitivity of analytical methods The purpose of this study was to investigate the analytical method of multi-residue pesticides in surface water samples by using of ultrahigh liquid chromatography in combination with high resolution mass spectrometry (UPLC-Orbitrap MS) In this work, pesticide presence was isolated from the matrix by solid-phase extraction (SPE) before analysis by the UPLC-Orbitrap MS Also, the parameters such as: limit of detection (LOD), limit of quantitation (LOQ), linearity, recovery… have been investigated to evaluate method through spiking experiments Finally, the developed method was applied to screening multi-residue of pesticides in real samples which were collected from several villages in Hanoi MATERIALS AND METHODS 2.1 Chemicals and reagents HPLC-grade methanol (MeOH), acetonitrile (ACN), ammonium formate (HCOONH4) and Formic acid (FA) with high purity were purchased from Merck (Germany) HPLCgrade water was obtained by purifying demineralized water in a Milli-Q Integral from Merck Millipore (France) Twelve investigated pesticides (high purities, > 90%) were acquired from Dr Ehrenstorfer GmH (Germany) Standard solution of 10 ppm was prepared by mixing and diluting the 1000 ppm stock individual solutions in ACN Solution of 10 ppm of surrogates (IS) including dimethoate-d6, dichlorvos-d6 (Dr Ehrenstorfer) and malathion-d10 (Toronto Research Chemicals) were prepared in MeOH The working standard solutions were built at concentration 5, 10, 25, 50, 100, 250, 500 ppb with 250 ppb surrogates in MeOH solvent 2.2 Instrumentation and analytical method An UPLC system (Ultimate 3000) coupled to a Q-Exactive Focus Orbitrap MS system (Thermo Scientific) was used to determine pesticides in surface water samples All of parameters of UPLC-HRMS system were monitored by the Thermo X-calibur software ver 4.0 For LC, a Thermo Hypersil gold PFP column (150 x 2.1 mm, µm) was used for separation of target analytes at temperature of 40 0C The binary mobile phases were 0.1% FA + mM HCOONH4 in H2O (A) and in MeOH (B) Their gradient elution was started with 2% B for 0.25 mins, raised to 30% B for 0.75 mins, linearily increased to 100% B in 24 mins (held for mins) then restored to the 2% B in 0.5 154 mins and held for mins to re-equilibrate the column for the next injection The flow rate was constantly kept at 0.3 mL.min-1 during chromatographic separation of time (37.5 mins) µL of each sample was injected to LC-Orbitrap MS system via autosampler Needle and sample loop in autosampler were washed triplicate by using mixture of methanol: deionized water (1:9, v:v) A system of Orbitrap MS using electrospray ionization (ESI), with 70000-FWHM resolution (at 200 Da) was operated in both positive and negative ionization modes The mass spectrometer was calibrated before each batch of measurement by Pierce Positive/negative ion mass calibration solution (Thermo Fisher, CAS number 88324) This system was optimized for each pesticide by direct infusion experiment Optimum operating conditions followed parameters: Sheath gas pressure at 32 psi, auxiliary gas flow rate at L.min-1, sweep gas flow rate at L.min-1, Spray voltage +2.8 kV and -2.5 kV for positive and negative mode, respectively Capillary and vaporizer temperature at 320 0C and 295 0C, respectively; S-lens RF level at 50 V The FullMS mode (resolution 70000-FWHM) was conducted in mass range 80-1000 to measure target ions of precursors The FullMS/ddMS2 (Full-scan data dependent MS/MS) mode could simultaneously record the fragmentation spectra for the precursors Besides, the FullMS/confirmation mode (with inclusion list) was also used to confirm fragments of the selected precursors Both the dd-MS2 and confirmation mode conditions followed parameters: resolution 17500-FWHM, mass isolation window 1.0 m/z, maximum and minimum automatic gain control (AGC) target 8x104 and 5x103, respectively; normalized collision energy (NCE) 30%; spectrum data format for confirmation: centroid A software of Thermo TraceFinder ver 3.3 was applied for data evaluation and reporting 2.3 Sample collection and preparation Twenty surface water samples were collected from local villages including Van Noi (coded N1), Tien Duong (N3), Tam Xa (N5) (Dong Anh district), Van Duc (Gia Lam district) (N4) and Yen My (Thanh Tri district) (N2) in Hanoi then acidified to pH by FA and stored at 0C until analysis For method evaluation, the experiment was conducted with pooled samples, which were the mixture of equal volume of individual sample SPE technique using Waters OASIS HLB cc column was applied for sample preparation Cartridges were firstly conditioned by 10 mL MeOH followed by 10 mL deionized water adjusted with pH about by FA Each 100 mL acidified surface water sample with 250 ppb IS, was loaded up to cartridge at drop.sec-1 flow rate by gravity Target compounds were eluted by 10 mL MeOH The SPE eluent was dried under a gentle nitrogen flow to 0.5 mL, then add mL mobile phase before removing solvent to exact mL Samples were filtered then injected into UPLC-HRMS system The real samples were followed above procedure for determination of pesticides RESULTS AND DISCUSSION 3.1 Optimization chromatographic separation for all target analytes In this work, Thermo Hypersil GOLD PFP column was used for chromatographic separation of multi-class pesticides based on retaining of polar compounds The working standard solution and matrix-match were prepared and injected on the LC-Orbitrap MS followed the optimized operating conditions which have shown in 2.2 As clearly shown on the Table 1, the repeatability of both retention time and precursor of all twelve selected compounds in standard solution and in matrix match were very good 155 Table 1: The retention time and mass accuracy of investigated analytes in neat solvent and match- matrix [M+H] or [M-H] experiment RT± SD Precursor (n=6), (Polarity) Neat solvent Match matrix Compound Chemical formula Dimethoate C5H12NO3PS2 230.0069 (+) 5.48 ± 0.03 230.0069 ± 0.0001 0.11 230.0069 ± 0.0001 0.14 Parathionmethyl C8H10NO5PS Organophosphate261.9944 (-) 6.40 ± 0.02 261.9945 ± 0.0001 0.38 261.9944 ± 0.0001 -0.06 Dichlorvos C4H7Cl2O4P 220.9532 (+) 7.81 ± 0.03 220.9533 ± 0.0001 0.23 220.9532 ± 0.0000 -0.08 Methomyl C5H10N2O2S 163.0536 (+) 4.47 ± 0.13 163.0535 ± 0.0000 -0.46 163.0536 ± 0.0001 0.20 Carbaryl C12H11NO2 202.0862 (+) 9.05 ± 0.04 202.0863 ± 0.0001 0.25 202.0863 ± 0.0001 0.33 Azoxystrobin C22H17N3O5 404.1241 (+) 13.19 ± 0.03 404.1238 ± 0.0001 -0.80 404.1236 ± 0.0001 -1.32 Dinotefuran C7H14N4O3 Neonicotinoid 201.0993 (-) 3.95 ± 0.13 201.0986 ± 0.0000 -3.48 201.0986 ± 0.0000 -3.40 Carbendazim C9H9N3O2 benzimidazole 192.0768 (+) 4.74 ± 0.04 192.0768 ± 0.0000 0.00 192.0768 ± 0.0001 0.00 C12H14ClNO2 Isoxazolidinone 240.0786 (+) 11.06 ± 0.04 240.0786 ± 0.0001 -0.21 240.0784 ± 0.0001 -0.83 C22H28N2O2 351.2080 ± 0.0001 0.57 351.2080 ± 0.0001 0.43 528.078 (+) 17.86 ± 0.02 528.0771 ± 0.0002 -1.74 528.0773 ± 0.0000 -1.33 Pyridazinone 365.1449 (+) 19.29 ± 0.03 365.1446 ± 0.0001 -0.82 365.1445 ± 0.0001 -1.14 Category Carbamate Clomazone Tebufenozide Strobilurin diacylhydrazine 351.2078 (-) 14.35 ± 0.02 Indoxacarb C22H17ClF3N3O7 Oxadiazine Pyridaben C19H25ClN2OS Mass Mass m/z ± SD (n=6) accuracy m/z ± SD (n=6) accuracy (ppm) (ppm) analytes was carried out by comparison of retention time, mass accuracies, fragments… with the standard at experimental conditions Fragments were searched in Mass bank and taken by Thermo Mass Frontier sofware ver 7.0 From table 2, mass accuracy of all product ions achieved below ppm, except dinotefuran (-11.5 ppm) and pyridaben (-5.44 ppm) 3.2 Mass accuracy of the target analytes The mass accuracy of all target compounds was assessed by injected times independently of 100 ngmL-1 neat solvent and sample with 25 ppb of all analytes on LC-Orbitrap MS system The theorical mass was calculated by online Envipat Web 2.2 From Table 1, it should also be noted that the excellent mass accuracy was achieved in both neat solvent and matrix-match solutions Mass accuracies of all target were below ± 3.5 ppm The identification of target 156 Table 2: Protonated mass and mass accuracy of product ions of target analytes Fragment Fragment m/z Mass m/z Mass Formula m/z theor Formula m/z theor exp accuracy exp accuracy Dimethoate C5H12NO3PS2 230.0069 (+) C2H6O2PS 124.9826 124.9820 -4.80 ParathionC8H10NO5PS 261.9944 (-) C7H6O3N 152.0348 152.0343 -3.29 C6H4O3N 138.0191 138.0187 -2.90 methyl Dichlorvos C4H7Cl2O4P 220.9532 (+) C2H8O4P 127.0160 127.0154 -4.72 CH4O2P 78.9949 78.9948 -1.27 Methomyl C5H10N2O2S 163.0536 (+) C3H6NS 88.0221 88.0219 -2.27 C3H8NOS 106.0326 106.0321 -4.72 Carbaryl C 12H11NO2 202.0862 (+) C10H9O 145.0653 145.0647 -4.14 C9H9 117.0704 117.0700 -3.42 Azoxystrobin C22H17N3O5 404.1241 (+) C21H14N3O4 372.0984 372.0972 -3.22 C20H14N3O3 344.1035 344.1024 -3.20 Dinotefuran C7H14N4O3 201.0993 (-) HN2O2 61.0038 61.0031 -11.47 Carbendazim C9H9N3O2 192.0768 (+) C8H6N3O 160.0511 160.0505 -3.75 Clomazone C12H14ClNO2 240.0786 (+) C7H6Cl 125.0158 125.0153 -4.00 Tebufenozide C22H28N2O2 351.2078 (-) C9H9O2 149.0602 149.0598 -2.68 Indoxacarb C22H17ClF3N3O7528.0780 (+) C15H7O3N 249.0426 249.0421 -2.01 C13H10ClN2O4 293.0329 293.0324 -1.71 Pyridaben C19H25ClN2OS 365.1449 (+) C11H15 147.1174 147.1166 -5.44 C15H18ClN2OS 309.0828 309.0814 -4.53 Compound Chemical formula Precursor (Polarity) using isotopic labelled internal standards It can be seen from table that correlation (R2) between analytical signal and analytical concentration were achieved higher than 0.99 The method of detected limit (MDL) and quantitative limit (MQL) were investigated by spiking experiments at 25 ppb target analytes with 250 ppb mixture of three surrogate compounds Based on European Pharmacopoeia guideline, LOD and LOQ was calculated by 3*S/N and 10*S/N, respectively, where S/N refers for signal to noise ratio From Table 3, MDL ranged from 0.0002 ng mL-1 (azoxystrobin) to 0.493 ng mL-1 (parathionmethyl) 3.3 Validation of the developed method In this work, the Waters Oasis HLB cartridge was selected because it is a universal sorbent that has been extensively used for extraction of organic contaminants, and its hydrophilic /lipophilic character makes it suitable for interaction with analytes of a wide polarity range From Table 3, recovery of target analytes was in ranged from 62% (azoxystrobin) to 125% (pyridaben) The lower recovery was attributed by ionization suppression in mass spectrometry, especially in heated electrospray ionization mass spectrometry The higher recovery was explained by enhancement of analytical in sample matrix However, both effects could be eliminated by Table 3: Calibration curves, MDL, MQL of twelve native compounds in this study Precursor (Polarity) Dimethoate 230.0069 (+) Parathion-methyl 261.9944 (-) Dichlorvos 220.9532 (+) Methomyl 163.0536 (+) Carbaryl 202.0862 (+) Azoxystrobin 404.1241 (+) Dinotefuran 201.0993 (-) Carbendazim 192.0768 (+) Clomazone 240.0786 (+) Tebufenozide 351.2078 (-) Indoxacarb 528.078 (+) Pyridaben 365.1449 (+) Compound RT ± SD, Regression equation R2 5.48 ± 0.03 6.40 ± 0.02 7.81 ± 0.03 4.47 ± 0.13 9.05 ± 0.04 13.19 ± 0.03 3.95 ± 0.13 4.74 ± 0.04 11.06 ± 0.04 14.35 ± 0.02 17.86 ± 0.02 19.29 ± 0.03 Y = 1.512e-2*X + 1.03e-1 Y = 2.631e4*X + 1.886e5 Y = 4.096e-3*X - 3.452e-2 Y = 2.868e-4*X - 3.706e-3 Y = 1.024e-2*X + 8.166e-2 Y = 4.916e-2*X + 1.123e-1 Y = 2.623e5*X - 2.953e5 Y = 1.073e-3*X - 2.462e-2 Y = 2.096e-2*X + 4.949e-2 Y = 1.805e5*X + 2.073e6 Y = 3.352e-3*X - 1.168e-2 Y = 9.504e-3*X - 6.26e-3 0.9995 0.9977 0.9999 0.9939 0.9995 0.9993 0.9999 0.9933 0.9993 0.9968 0.9959 0.9995 157 MDL MQL Recovery (ng/mL) (ng/mL) (%) 0.001 0.004 93.68 0.493 1.644 117.71 0.157 0.522 85.74 0.282 0.940 74.40 0.012 0.042 100.33 0.0002 0.001 62.47 0.137 0.456 73.46 0.005 0.018 108.30 0.016 0.052 92.60 0.045 0.151 111.43 0.047 0.157 72.00 0.055 0.183 124.90 3.5 Analysis of real samples In general, carbendazim and indoxacarb were found in all of twenty investigated samples Dinotefuran and clomazone were present with lower frequencies (67% and 56%, respectively) Meanwhile, insecticide namely Tebufenozide was detected in 22% samples It was hardly to detect organophosphate group (dimethoate, parathion-methyl, dichlorvos), carbaryl and pyridaben Comparison with report taken by Rousis et.al., carbendazim was observed with the highest frequency in all test samples in both Spain and Italy Besides, carbaryl, methomyl, parathion-methyl, dichlorvos, dimethoate were not present in collected samples in this study, resulting from the regular recently banning pesticide uses in TT03/2018/TT-BNNPTNN Figure 3: Pesticide distribution in individual sample Figure shows pesticide distribution in individual samples Generally, in N3 and N5 villages, Dinotefuran as recorded was found at the highest concentration in surface water samples The other samples were found the significant distribution of carbendazim CONCLUSION This study was developed method of multiresidue pesticide analysis in surface water samples collected from several villages in Hanoi by using SPE technique for preparation and LC-ESI-Orbitrap MS for analysis This procedure can analyze simultaneous difference pesticide groups by quantification in fullscan mode at 70000-FWHM resolution and confirmation of fragmentation based on datadependent MSMS mode at 17500-FWHM resolution This method was applied to analyze twelve pesticides in twenty investigated samples It demonstrated clearly that the surface samples were contaminated with carbendazim, dinotefuran and indoxacarb ACKNOWLEDDGEMENT This research is funded by Vietnam National Foundation for Science and Technology Development (NAFOSTED) under grant number 104.04-2018.331 REFERENCES [1] J Casado, D Santillo, P Johnston, “Multiresidue analysis of pesticides in surface water by liquid chromatography quadrupole-Orbitrap high resolution tandem mass spectrometry,” Analytica Chimica Acta, vol 1024, pp 1-17, 2018 [2] Water Corporation, “QuEChERS Procedure Figure 2: The amount of individual analytes in areas Figure shows a summary of twelve pesticide concentrations in five investigated areas Indoxacarb displayed the highest concentration (1010 ng mL-1 and 545 ng mL-1) in N3 and N5 areas, respectively Meanwhile, in both N2 and N4 areas, carbendazim was occurred at the top leading level (> 100 ng mL-1) It was significant to pay attention that carbendazim is one of pesticides are not approved by the EU, according to the EU regulation 1107/2009 Carbendazim can be a metabolite of benomyl and thiophanate Besides, clomazone was found 24.1 ng mL-1- the highest value in N1 area 158 For Multi-Residue Pesticide Analysis -disQuE dispersive Sample Preparation,” Waters - The Science of What’s Possible pp 1–8, 2011 [3] Helen V Botitsi, Spiros D Garbis, Anastasios Economou, and Despina F Tsipi, “Current Mass spectrometry strategies for the analysis of pesticides and their metabolites in food and water matrices,” Wiley Online Library, 2010 [4] Nikolaos I Rousis, Richard Bade, Lubertus Bijlsma, Ettore Zuccato, Juan V Sancho, Felix Hernandez, Sara Castiglioni, “Monitoring a large number of pesticides and transformation products in water samples from Spain and Italy,” Environmental Research, vol 156, pp 31-38, 2017 [5] R Meffe and I de Bustamante, “Emerging organic contaminants in surface water and groundwater: A first overview of the situation in Italy,” Sci Total Environ., vol 481, no 1, pp 280–295, 2014 [6] Anastassiades et al, “Fast and Easy Multiresidue Method Employing Acetonitrile,” J AOAC Int., vol 86, no 2, pp 412–431, 2003 [7] Ministry of Agriculture and Rural development, Circulars No.03, 2018 [8] N Ochiai et al., “Optimization of a multiresidue screening method for the determination of 85 pesticides in selected food matrices by stir bar sorptive extraction and thermal desorption GC-MS,” J Sep Sci., vol 28, no 9–10, pp 1083–1092, 2005 [9] Helvécio C Menezes, Breno P Paulo, Maria Jose N Paiva, and Zenilda L Cardeal, “A simple and quick method for the determination of pesticides in environmental water by HF-LPME-GCMS,” Journal of Analytical methods in Chemistry, vol 2016 [10] Rajski, M M Gómez-Ramos, and A R Fernández-Alba, “Application of LC-Time-ofFlight and Orbitrap-MS/MS for Pesticide Residues in Fruits and Vegetables,” Comprehensive Analytical Chemistry, vol 71 pp 119–154, 2016 [11] A Kamel, “Refined methodology for the determination of neonicotinoid pesticides and their metabolites in honey bees and bee products by liquid chromatography-tandem mass spectrometry (LC-MS/MS),” J Agric Food Chem., vol 58, no 10, pp 5926–5931, 2010 [12] S J Lehotay, Y Sapozhnikova, and H G J Mol, “Current issues involving screening and identification of chemical contaminants in foods by mass spectrometry,” TrAC - Trends Anal Chem., vol 69, pp 62–75, 2015 [13] J F García-Reyes, M D Hernando, A Molina-Díaz, and A R Fernández-Alba, “Comprehensive screening of target, non-target and unknown pesticides in food by LC-TOFMS,” TrAC - Trends in Analytical Chemistry, vol 26, no pp 828–841, 2007 [14] California Department of Food and Agriculture, “Determination of Acephate and Methamidophos in SW by LCMS,” 2008 [15] “Determination of pesticide residues in ground water by LC-MSMS” https://www.researchgate.net/publication/3038 43678 159 ... resolution mass spectrometry (UPLC- Orbitrap MS) In this work, pesticide presence was isolated from the matrix by solid-phase extraction (SPE) before analysis by the UPLC -Orbitrap MS Also, the parameters... injected to LC -Orbitrap MS system via autosampler Needle and sample loop in autosampler were washed triplicate by using mixture of methanol: deionized water (1:9, v:v) A system of Orbitrap MS using... Instrumentation and analytical method An UPLC system (Ultimate 3000) coupled to a Q-Exactive Focus Orbitrap MS system (Thermo Scientific) was used to determine pesticides in surface water samples