Tài liệu CCNA Semester 1 Skills Based Final – Part 1 Cable Build / Test pptx

CCNA Semester 1 Skills Based Final – Part 1 Cable Build / Test Name: _____________Date: _________ (Total possible Points: 20) Objective: Build an Ethernet 10BaseT straight thru cable to connect from a workstation to a hub or switch. Use UTP cable and wire all eight conductors using the correct wire colors and pins for either a T568A or T568B. Test the cable with a cable tester to verify continuity, correct pinouts and cable length. This cable can be used to connect your workstation to the hub or switch for exam part 3. Directions: Obtain a piece of CAT 5 cable (depending on use) and two RJ45 connectors. Use a crimping tool to attach the RJ 45 connectors to the cable. Use a cable tester to test the cable to verify that is functional. Indicate which cabling pinout standard (T568A or T568B) you will use ___________ 1) Are the correct wires pins in the correct position? Initial _______ (10 pts) 2) Does cable test OK with cable tester? Initial _______ (10 pts) Points Scored: _______ Semester 1 Skills Based Final – Part 2 Network Concepts (Total possible Points: 30) Objective: Answer the 3 questions on networking concepts as assigned by the instructor. Write the questions assigned in the space provided below. You may be asked to answer orally or write your answers on the back of this sheet. Answers should be as detailed as possible for maximum credit. Question 1: (10 pts): _________________________________________________________________________________ _________________________________________________________________________________ Question 2: (10 pts) _________________________________________________________________________________ _________________________________________________________________________________ _________________________________________________________________________________ Question 3: (10 pts) _________________________________________________________________________________ _________________________________________________________________________________ _________________________________________________________________________________ Points Scored: ____________ Semester 1 Skills Based Final – Part 3 Network Connection Workstation #: _______ (Total possible Points: 50) Objective: Connect your workstation to a LAN. Configure the network settings and troubleshoot as necessary. Use your web browser to connect to router interface 152.20.71.237 and display the web interface. After you have successfully connected to the router, the instructor will introduce problems into the PC and/or network which must be resolved and documented in the space provided. Include the following: symptoms, causes, details of tests done, detailed problem results (from layer 1 testing), detailed solutions. You will be assigned a workstation number that will become the useable subnet # with which you will perform this assessment. Make sure you have an appropriate assigned subnet number before starting. You will be using a class C network 193.5.5.0 which is divided into subnets by borrowing 5 bits from the network portion of the address. The subnet number assigned is the same usable subnet (1 st , 2 nd 3 rd etc.) as your workstation number. The proctor must initial each step as you answer the following questions. The default gateway (nearside router port) for your host is 193.5.5.1. Write the IP address of your workstation here: ____________________ 1. What is the subnet mask? ____________________________ Initial ________ (5 pts) 2. Subnet host IP address range? _________________________ Initial ________ (5 pts) 3. Network address of your subnet? ______________________ Initial ________ (5 pts) 4. Broadcast address of your subnet? _____________________ Initial ________ (5 pts) 5. Ping the router default gateway Initial ________ (10 pts) 6. Open the web page at 152.20.71.237 with your browser. Initial ________ (10 pts) 7. Identify and resolve troubleshooting problems listed below Initial ________ (10 pts) Total points _______ Troubleshooting Activity Record (use back if necessary) Symptom / Cause Tests / Results Detailed Solutions Points Scored: Part 1 ____ +Part 2 _____ +Part 3 _____ = Total ______ WS1 WS2 WS3 … . CCNA Semester 1 Skills Based Final – Part 1 Cable Build / Test Name: _____________Date: _________ (Total possible Points: 20) Objective: Build. ___________ 1) Are the correct wires pins in the correct position? Initial _______ (10 pts) 2) Does cable test OK with cable tester? Initial _______ (10 pts)