autocad 2008 autocad lt 2008 no experience required - phần 10 docx

... 483–486, 484, 485 doors, 100 , 100 –124 alternate sliding-glass door, 124 dynamic block for, 369–370 rotating, 104 105 , 105 sliding glass door, 114–124 swinging doors, 100 108 swinging doors finish, ... 495, 666 angular units, 75–76, 666 Annotative property, for multiline text, 334 AR-RROOF pattern, 428 AR-RSHKE pattern, 435 arc order of selecting points for, 107 quadrant snaps for,...

Ngày tải lên: 08/08/2014, 23:21

... status bar if necessary. The End- point, Midpoint, and Intersection osnaps are now active. If not, then choose Settings from the shortcut menu to open the Drafting Set- tings dialog box at the Object ... 227 26531ch07.qxd 4/3/07 12:52 PM Page 227 NOTE If no objects are selected and you set Linetype Scale in the Prop- erties palette to a number other than 1.000, any noncontinuous lines that...

Ngày tải lên: 08/08/2014, 23:21

... entities in a current drawing. Using the Drop-Down Menus 13 26531ch01.qxd 3/30/07 4:59 PM Page 13 AUTOCAD ® 2008 AND AUTOCAD LT ® 2008 NO EXPERIENCE REQUIRED ™ David Frey Jon McFarland Wiley Publishing, ... I say AutoCAD, I mean both AutoCAD and AutoCAD LT. I’ll also refer to AutoCAD LT as LT throughout this chapter and the rest of the book to specifically refer t...

Ngày tải lên: 08/08/2014, 23:20

... dis- played. The notation always uses an expression that indicates a number from 1 to 10 that is to be multiplied by a power of 10. In this case, the power is 1, so the notation means 3.05 × 10, ... saveas↵). 7. Click Save. Notice that the AutoCAD title bar displays the new name of the file along with its path. It’s now safe to exit AutoCAD. 8. If you want to shut down AutoCAD at t...

Ngày tải lên: 08/08/2014, 23:20

... command has a nonzero radius setting that you want to keep, hold down the Shift key to set the radius to zero for one use of the com- mand. After the com- mand ends, the radius returns to its nonzero ... AutoSnap Set- tings area, click the Colors button to open the Drawing Window Colors dialog box. 2D Model Space and AutoSnap Marker will be selected. Open the Color drop-down list in the upper...

Ngày tải lên: 08/08/2014, 23:20

... some of which are beyond the scope of this book. For a more in-depth dis- cussion on blocks, see Mastering AutoCAD 2008 and AutoCAD LT 2008 by George Omura (Wiley, 2007). If You Would Like More ... single-line text in the cabin drawing. Finally, you’ll look at the methods for creating and controlling multiline text as it’s used for notes and tables. If you work in a non-AEC profes-...

Ngày tải lên: 08/08/2014, 23:21

... following widths: 2&apos ;-0 ", 2&apos ;-6 ", 3&apos ;-0 ", and 3&apos ;-6 ". Chapter 9 • Using Dynamic Blocks and Tables364 26531ch09.qxd 3/30/07 6:11 PM Page 364 Note the small exclamation ... Turn off Polar and Osnap, and then at the Specify action loca- tion or [Multiplier/Offset]: prompt, click to place the light- ning-bolt action symbol just above the door....

Ngày tải lên: 08/08/2014, 23:21

... performed a typi- cal installation of AutoCAD, the file should be in the C:\Program Files \AutoCAD 2008\ UserDataCache\Support folder. LT users should substitute AutoCAD LT 2008 for AutoCAD 2008 in the ... the tile pattern looks OK, right-click again. FIGURE 11.17: The tiled hatch pattern in place Note that the user-defined pattern has no scale factor to worry about. You sim...

Ngày tải lên: 08/08/2014, 23:21

... notation. With the surveyor’s unit system, a sloping line that has an up-and-to-the-left direction has a down-and-to-the-right direction if you start from the opposite end. So, in laying out property ... a line near the upper-right corner of the grid. 10. Be sure Snap is turned off. Then, enter the following: @140 < n90dw↵ @90 < s42d30'w↵ @140 < s67d30'e↵ @80 < n52d49&a...

Ngày tải lên: 08/08/2014, 23:21

... who do not wish to continue learning the 3D aspects of AutoCAD, I hope you have found the book useful in helping you learn AutoCAD 2008 and AutoCAD LT 2008. Good luck in your future with AutoCAD. ... is open. If it’s not, click the right-pointing arrow in the lower-right corner to open it. In the upper-right corner, make sure None is displayed in the Plot Style Table drop-down lis...

Ngày tải lên: 08/08/2014, 23:21