autocad 2008 autocad lt 2008 no experience required - phần 8 pot

... notation. With the surveyor’s unit system, a sloping line that has an up-and-to-the-left direction has a down-and-to-the-right direction if you start from the opposite end. So, in laying out property ... a line near the upper-right corner of the grid. 10. Be sure Snap is turned off. Then, enter the following: @140 < n90dw↵ @90 < s42d30'w↵ @140 < s67d30'e↵ @80 < n52d49&a...

Ngày tải lên: 08/08/2014, 23:21

... following widths: 2&apos ;-0 ", 2&apos ;-6 ", 3&apos ;-0 ", and 3&apos ;-6 ". Chapter 9 • Using Dynamic Blocks and Tables364 26531ch09.qxd 3/30/07 6:11 PM Page 364 Note the small exclamation ... Turn off Polar and Osnap, and then at the Specify action loca- tion or [Multiplier/Offset]: prompt, click to place the light- ning-bolt action symbol just above the door....

Ngày tải lên: 08/08/2014, 23:21

... performed a typi- cal installation of AutoCAD, the file should be in the C:\Program Files \AutoCAD 20 08\ UserDataCache\Support folder. LT users should substitute AutoCAD LT 20 08 for AutoCAD 20 08 in the ... the tile pattern looks OK, right-click again. FIGURE 11.17: The tiled hatch pattern in place Note that the user-defined pattern has no scale factor to worry about. Y...

Ngày tải lên: 08/08/2014, 23:21

... Drop-Down Menus 13 26531ch01.qxd 3/30/07 4:59 PM Page 13 AUTOCAD ® 20 08 AND AUTOCAD LT ® 20 08 NO EXPERIENCE REQUIRED ™ David Frey Jon McFarland Wiley Publishing, Inc. 26531fm.qxd 4/3/07 9: 18 PM ... Starting AutoCAD If you installed AutoCAD using the default settings for the location of the pro- gram files, start the program by choosing Start ➣ Programs ➣ Autodesk ➣...

Ngày tải lên: 08/08/2014, 23:20

... saveas↵). 7. Click Save. Notice that the AutoCAD title bar displays the new name of the file along with its path. It’s now safe to exit AutoCAD. 8. If you want to shut down AutoCAD at this time, ... spacing 8. Move the crosshair cursor to the upper-right corner of the grid, and check the coordinate readout. It should display 60&apos ;-0 ", 40&apos ;-0 ", 0&apos ;-0 &quo...

Ngày tải lên: 08/08/2014, 23:20

... command has a nonzero radius setting that you want to keep, hold down the Shift key to set the radius to zero for one use of the com- mand. After the com- mand ends, the radius returns to its nonzero ... and swing in another opening 0 use the Offset and Trim commands to make a sliding- glass door Chapter 4 • Gaining Drawing Strategies: Part 11 28 26531ch04.qxd 3/30/07 5:09 PM Page 1 28 6. T...

Ngày tải lên: 08/08/2014, 23:20

... (bottom) Chapter 7 • Combining Objects into Blocks2 28 26531ch07.qxd 4/3/07 12:52 PM Page 2 28 2. Click the Headers layer. The drop-down list closes. Headers is now in the box; this tells you that the Headers ... status bar if necessary. The End- point, Midpoint, and Intersection osnaps are now active. If not, then choose Settings from the shortcut menu to open the Drafting Set- tings dialo...

Ngày tải lên: 08/08/2014, 23:21

... 1&apos ;-0 " 12 1 ⁄2" = 1&apos ;-0 " 24 1 ⁄4" = 1&apos ;-0 " 48 1 8& quot; = 1&apos ;-0 " 96 1 ⁄16" = 1&apos ;-0 " 192 Defining a Text Style for Room Labels Now that ... and AutoCAD s DesignCenter. Blocks follow a set of complex rules, some of which are beyond the scope of this book. For a more in-depth dis- cussion on blocks, see Mastering...

Ngày tải lên: 08/08/2014, 23:21

... who do not wish to continue learning the 3D aspects of AutoCAD, I hope you have found the book useful in helping you learn AutoCAD 20 08 and AutoCAD LT 20 08. Good luck in your future with AutoCAD. ... is open. If it’s not, click the right-pointing arrow in the lower-right corner to open it. In the upper-right corner, make sure None is displayed in the Plot Style Table drop-down...

Ngày tải lên: 08/08/2014, 23:21

... balcony, 485 , 486 with Baseline command, 480 , 480 – 482 , 481 Continue command for, 479– 480 , 480 placing on drawing, 476– 486 summary of changes, 470 vertical dimensions, 483 – 486 , 484 , 485 doors, ... 388 , 388 –409 balcony, 4 08, 4 08 concrete hatch for foundation, 432–433, 433 copying, 4 18, 4 18 door and wall hatch, 433–436, 434, 435 door, step and windows, 402–4 08, 403 fini...

Ngày tải lên: 08/08/2014, 23:21