autocad 2008 autocad lt 2008 no experience required - phần 7 pot

... performed a typi- cal installation of AutoCAD, the file should be in the C:\Program Files \AutoCAD 2008\ UserDataCache\Support folder. LT users should substitute AutoCAD LT 2008 for AutoCAD 2008 in the ... Figure 11. 17) . If the tile pattern looks OK, right-click again. FIGURE 11. 17: The tiled hatch pattern in place Note that the user-defined pattern has no scale factor to...

Ngày tải lên: 08/08/2014, 23:21

... following widths: 2&apos ;-0 ", 2&apos ;-6 ", 3&apos ;-0 ", and 3&apos ;-6 ". Chapter 9 • Using Dynamic Blocks and Tables364 26531ch09.qxd 3/30/ 07 6:11 PM Page 364 Note the small exclamation ... block Creating a Dynamic Block 373 26531ch09.qxd 3/30/ 07 6:11 PM Page 373 7. At the Specify action location or [Base type]: prompt, place the Scale lightning-bolt sym...

Ngày tải lên: 08/08/2014, 23:21

... minutes is shown as N30d30'E in AutoCAD notation. With the surveyor’s unit system, a sloping line that has an up-and-to-the-left direction has a down-and-to-the-right direction if you start from ... a line near the upper-right corner of the grid. 10. Be sure Snap is turned off. Then, enter the following: @140 < n90dw↵ @90 < s42d30'w↵ @140 < s67d30'e↵ @80 < n52d49&...

Ngày tải lên: 08/08/2014, 23:21

... Project. 2. In the resulting dialog, shown in Figure 1. 57, click the Browse button. 3. Browsing will throw you into a category with several other templates. You can now choose a different ... exactly where they may have mapped Revit. 6. Notice there is a list of doors. Select Single-Raised Panel with Sidelights.rfa , and click Open. 7. In the Properties dialog, click the change ......

Ngày tải lên: 07/07/2014, 07:20

... the Drop-Down Menus 13 26531ch01.qxd 3/30/ 07 4:59 PM Page 13 AUTOCAD ® 2008 AND AUTOCAD LT ® 2008 NO EXPERIENCE REQUIRED ™ David Frey Jon McFarland Wiley Publishing, Inc. 26531fm.qxd 4/3/ 07 9:18 ... at (800) 76 2-2 974 , outside the U.S. at (3 17) 57 2-3 993 or fax (3 17) 57 2-4 002. Wiley also publishes its books in a variety of electronic formats. Some content...

Ngày tải lên: 08/08/2014, 23:20

... As or saveas↵). 7. Click Save. Notice that the AutoCAD title bar displays the new name of the file along with its path. It’s now safe to exit AutoCAD. 8. If you want to shut down AutoCAD at this ... radian equals 57. 3 degrees, and 360 degrees equals 6.28 radians, or 2π radians. AutoCAD uses r as the symbol for radians. Summarizing AutoCAD s Units 75 26531ch03.qxd 3/30/ 07 5:03...

Ngày tải lên: 08/08/2014, 23:20

... TYP R0.50" TYP R0 .75 " TYP R0.25" TYP 8.00 R 0 .75 R 1.00 .25 DIA R 0.50 R 0.50 Note: Thickness 0.125 If You Would Like More Practice… 169 26531ch05.qxd 3/30/ 07 5:11 PM Page 169 Positioning ... You Would Like More Practice… 1 27 26531ch04.qxd 3/30/ 07 5:09 PM Page 1 27 2. Offset the right inside wall line 3' to the left. Then, offset this new line 9&apos ;-1 0&quo...

Ngày tải lên: 08/08/2014, 23:20

... 2 37 26531ch 07. qxd 4/3/ 07 12:52 PM Page 2 37 CHAPTER 7 Combining Objects into Blocks Ǡ Creating and inserting blocks Ǡ Using the Wblock command Ǡ Detecting blocks in a drawing Ǡ Working with AutoCAD s ... rotation angle < 0.00>: prompt, press ↵ again to accept the default angle of 0°. The door3_0 block properly appears in the drawing (see the bottom of Figure 7. 7). FIGURE 7....

Ngày tải lên: 08/08/2014, 23:21

... the navi- gation bar can be on the left or right side. FIGURE 7. 46: The tool palettes displayed on the screen Sharing Information Between Drawings 275 26531ch 07. qxd 4/3/ 07 12:52 PM Page 275 FIGURE ... highlighted at the default of 0&apos ;-0 ". 7. Enter 12, and then press Tab again. A height of 1&apos ;-0 " replaces the default height. Setting Up Text Styles 285 ǡ By de...

Ngày tải lên: 08/08/2014, 23:21

... who do not wish to continue learning the 3D aspects of AutoCAD, I hope you have found the book useful in helping you learn AutoCAD 2008 and AutoCAD LT 2008. Good luck in your future with AutoCAD. ... Page Setup dia- log box. 6. Notice that in the Plot Style Table (Pen Assignments) area, None is selected. No plot-style table file has been assigned to this layout. 7. Open the dro...

Ngày tải lên: 08/08/2014, 23:21